共查询到20条相似文献，搜索用时 31 毫秒
1.
Micro- and macroscale experiments which document the dynamics of salt damage to porous stone have yielded data which expose weaknesses in earlier interpretations. Previously unexplained differences are found in crystal morphology, crystallization patterns, kinetics and substrate damage when comparing the growth of mirabilite (Na2SO4. 10H2O) and thenardite (Na2SO4) versus halite (NaCl). The crystallization pattern of sodium sulphate was strongly affected by relative humidity (RH), while a lesser RH effect was observed for sodium chloride. Macroscale experiments confirmed that mirabilite (crystallizing at RH > 50 per cent) and thenardite (crystallizing at RH < 50 per cent) tend to form subflorescence in highly localized areas under conditions of constant RH and temperature. This crystallization pattern was more damaging than that of halite, since halite tended to grow as efflorescence or by filling the smallest pores of the stone in a homogeneous fashion, a result which contradicts Wellman and Wilson's theoretical model of salt damage. Low RH promoted rapid evaporation of saline solutions and higher supersaturation levels, resulting in the greatest damage to the stone in the case of both sodium sulphate and sodium chloride crystallization. At any particular crystallization condition, sodium chloride tended to reach lower supersaturation levels (resulting in the crystallization of isometric crystals) and created negligible damage, while sodium sulphate reached higher supersaturation ratios (resulting in non-equilibrium crystal shapes), resulting in significant damage. ESEM showed no damage from sodium sulphate due to hydration. Instead, after water condensation on thenardite crystals, rapid dissolution followed by precipitation of mirabilite took place, resulting in stone damage by means of crystallization pressure generation. It is concluded that salt damage due to crystallization pressure appears to be largely a function of solution supersaturation ratio and location of crystallization. These key factors are related to solution properties and evaporation rates, which are constrained by solution composition, environmental conditions, substrate properties, and salt crystallization growth patterns. When combined with a critical review of salt damage literature, these experiments allow the development of a model which explains variations in damage related to combinations of different salts, substrates and environmental conditions. Copyright © 1999 John Wiley & Sons, Ltd. 相似文献
2.
Throughout the world, large caves in rocks (tafoni) are found, which originate from salt weathering. The mechanisms that control their development are poorly understood. The growth of tafoni has been studied with a model that describes how a rock surface, containing a small pit, disintegrates by salt crystallization during wetting/drying cycles. In the model the rock is mapped on a grid. The migration and crystallization of salts are simulated explicitly in the drying phase of a cycle. At the end of each wetting/drying cycle the amount of salt deposited at the grid nodes is evaluated and the shape of the rock surface is adjusted by removing nodes. The length of the drying period in a single cycle proved to be the key parameter. For short drying periods the amount of crystallized salt at the surface is proportional to the drying rate. Therefore, for short drying periods most salts are deposited at the more exterior parts of the rock surface. As a result, most damage will develop at these parts of the surface, which results in smooth surfaces. Due to the characteristics of the drying process for long drying periods, most salts accumulate at regions with low evaporation rates, which are the sheltered parts of the rock surface. These parts are not exposed to the wind or the sun. As a result, the pit grows and a tafone develops. Copyright © 2004 John Wiley & Sons, Ltd. 相似文献
3.
A. S. Goudie 《地球表面变化过程与地形》1999,24(8):715-724
A total of 21 different types of British and European Mesozoic limestones have been subjected to simulated salt weathering using sodium sulphate (Na2SO4) with the following aims: assessment of the relative durabilities of different types of limestone; assessment of the importance of modulus of elasticity and other factors in affecting durability; and assessment of the use of impulse excitation techniques to monitor changes in rock modulus of elasticity. The rocks showed a wide spectrum of durabilities; while rocks with high values of modulus of elasticity, lower water absorption capacities, high densities and low salt uptakes tended to be durable, there were anomalies, the explanation for which probably lies in their pore structures. Non-destructive testing techniques showed that, although the more durable rocks failed to lose weight or to show visual signs of disintegration, their modulus of elasticity values did tend to decline, indicating a loss in strength. Copyright © 1999 John Wiley & Sons, Ltd. 相似文献
4.
This research characterizes the weathering of natural building stone using an unsteady‐state portable probe permeameter. Variations between the permeability properties of fresh rock and the same rocks after the early stages of a salt weathering simulation are used to examine the effects of salt accumulation on spatial variations in surface rock permeability properties in two limestones from Spain. The Fraga and Tudela limestones are from the Ebro basin and are of Miocene age. Both stone types figure largely in the architectural heritage of Spain and, in common with many other building limestones, they are prone to physical damage from salt crystallization in pore spaces. To examine feedbacks associated with salt accumulation during the early stages of this weathering process, samples of the two stone types were subjected to simulated salt weathering under laboratory conditions using magnesium sulphate and sodium chloride at concentrations of 5% and 15%. Permeability mapping and statistical analysis (aspatial statistics and spatial prediction) before and after salt accumulation are used to assess changes in the spatial variability of permeability and to correlate these changes with salt movement, porosity change, potential rock deterioration and textural characteristics. Statistical analyses of small‐scale permeability measurements are used to evaluate the drivers for decay and hence aid the prediction of the weathering behaviour of the two limestones. Copyright © 2010 John Wiley & Sons, Ltd. 相似文献
5.
A. S. Goudie 《地球表面变化过程与地形》1986,11(3):275-285
‘The wick effect’ is the upward migration of saline solutions into rocks and their subsequent crystallization. Lower Carboniferous sandstone blocks of rectangular shape have been subjected to this process in the laboratory using a range of salt types, a range of salt concentrations, and various mixtures of salts. Some treatments produced severe disintegration, notably sodium carbonate and a mixture of sodium carbonate with magnesium sulphate, whereas other salts (including sodium chloride and gypsum) were much less effective. The debris produced by this experimental salt weathering included appreciable quantities of silt-sized material, which were analysed with a laser granulometer. Such material could provide a source for desert loess. 相似文献
6.
C. Cardell T. Rivas M.J. Mosquera J.M. Birginie A. Moropoulou B. Prieto B. Silva R. Van Grieken 《地球表面变化过程与地形》2003,28(1):1-14
A saline‐spray artificial ageing test was used to simulate the effects produced in granites and sedimentary rocks (calcarenites, micrites and breccia) under conditions in coastal environments. Three main points were addressed in this study: the durability of the different kinds of rock to salt decay, the resulting weathering forms and the rock properties involved in the weathering processes. For this, mineralogical and textural characterization of each of the different rocks was carried out before and after the test. The soluble salt content at different depths from the exposed surfaces was also determined. Two different weathering mechanisms were observed in the granite and calcareous rocks. Physical processes were involved in the weathering of granite samples, whereas dissolution of calcite was also involved in the deterioration of the calcareous rocks. We also showed that microstructural characteristics (e.g. pore size distribution), play a key role in salt damage, because of their influence on saline solution transport and on the pressures developed within rocks during crystallization. Copyright © 2003 John Wiley & Sons, Ltd. 相似文献
7.
Here we characterize the nutrient content in the outflow of the Green Lake 5 rock glacier, located in the Green Lakes Valley of the Colorado Front Range. Dissolved organic carbon (DOC) was present in all samples with a mean concentration of 0·85 mg L?1 . A one‐way analysis of variance test shows no statistical difference in DOC amounts among surface waters (p = 0·42). Average nitrate concentrations were 69 µmoles L?1 in the outflow of the rock glacier, compared to 7 µmoles L?1 in snow and 25 µmoles L?1 in rain. Nitrate concentrations from the rock glacier generally increased with time, with maximum concentrations of 135 µmoles L?1 in October, among the highest nitrate concentrations reported for high‐elevation surface waters. These high nitrate concentrations appear to be characteristic of rock glacier outflow in the Rocky Mountains, as a paired‐difference t‐test shows that nitrate concentrations from the outflow of 7 additional rock glaciers were significantly greater compared to their reference streams (p = 0·003). End‐member mixing analysis suggest that snow was the dominant source of nitrate in June, ‘soil’ solution was the dominant nitrate source in July, and base flow was the dominant source in September. Fluoresence index values and PARAFAC analyses of dissolved organic matter (DOM) are also consistent with a switch from terrestrial DOM in the summer time period to an increasing aquatic‐like microbial source during the autumn months. Copyright © 2006 John Wiley & Sons, Ltd. 相似文献
8.
M. A. Coombes L. A. Naylor R. C. Thompson L. Gómez‐Pujol R. J. Fairhurst 《地球表面变化过程与地形》2011,36(5):582-593
Microorganisms are a ubiquitous feature of most hard substrata on Earth and their role in the geomorphological alteration of rock and stone is widely recognized. The role of microorganisms in the modification of engineering materials introduced into the intertidal zone through the construction of hard coastal defences is less well understood. Here we use scanning electron microscopy (SEM) to examine microbial colonization and micro‐scale geomorphological features on experimental blocks of limestone, granite and marine concrete after eight months' exposure in the intertidal zone in Cornwall, UK. Significant differences in the occurrence of microbial growth features, and micro‐scale weathering and erosion features were observed between material types (ANOVA p < 0·000). Exposed limestone blocks were characterized by euendolithic borehole erosion (99% occurrence) within the upper 34·0 ± 12·3 µm of the surface. Beneath the zone of boring, inorganic weathering (chemical dissolution and salt action) had occurred to a depth of 125·0 ± 39·0 µm. Boring at the surface of concrete was less common (27% occurrence), while bio‐chemical crusting was abundant (94% occurrence, mean thickness 45·1 ± 27·7 µm). Crusts consisted of biological cells, salts and other chemical precipitates. Evidence of cryptoendolithic growth was also observed in limestone and concrete, beneath the upper zone of weathering. On granite, biological activity was restricted to thin epilithic films (<10 µm thickness) with some limited evidence of mechanical breakdown. Results presented here demonstrate the influence of substratum lithology, hardness and texture on the nature of early micro‐scale colonization, and the susceptibility of different engineering materials to organic weathering and erosion processes in the intertidal zone. The implications of differences in initial biogeomorphic responses of materials for long‐term rock weathering, ecology and engineering durability are discussed. Copyright © 2010 John Wiley & Sons, Ltd. 相似文献
9.
Relationships between riverbed morphology, concavity, rock type and rock uplift rate are examined to independently unravel the contribution of along-strike variations in lithology and rates of vertical deformation to the topographic relief of the Oregon coastal mountains. Lithologic control on river profile form is reflected by convexities and knickpoints in a number of longitudinal profiles and by general trends of concavity as a function of lithology. Volcanic and sedimentary rocks are the principal rock types underlying the northern Oregon Coast Ranges (between 46°30′ and 45°N) where mixed bedrock–alluvial channels dominate. Average concavity, θ, is 0·57 in this region. In the alluviated central Oregon Coast Ranges (between 45° and 44°N) values of concavity are, on average, the highest (θ = 0·82). South of 44°N, however, bedrock channels are common and θ = 0·73. Mixed bedrock–alluvial channels characterize rivers in the Klamath Mountains (from 43°N south; θ = 0·64). Rock uplift rates of ≥0·5 mm a−1, mixed bedrock–alluvial channels, and concavities of 0·53–0·70 occur within the northernmost Coast Ranges and Klamath Mountains. For rivers flowing over volcanic rocks θ = 0·53, and θ = 0·72 for reaches crossing sedimentary rocks. Whereas channel type and concavity generally co-vary with lithology along much of the range, rivers between 44·5° and 43°N do not follow these trends. Concavities are generally greater than 0·70, alluvial channels are common, and river profiles lack knickpoints between 44·5° and 44°N, despite the fact that lithology is arguably invariant. Moreover, rock uplift rates in this region vary from low, ≤0·5 mm a−1, to subsidence (<0 mm a−1). These observations are consistent with models of transient river response to a decrease in uplift rate. Conversely, the rivers between 44° and 43°N have similar concavities and flow on the same mapped bedrock unit as the central region, but have bedrock channels and irregular longitudinal profiles, suggesting the river profiles reflect a transient response to an increase in uplift rate. If changes in rock uplift rate explain the differences in river profile form and morphology, it is unlikely that rock uplift and erosion are in steady state in the Oregon coastal mountains. Copyright © 2006 John Wiley & Sons, Ltd. 相似文献
10.
Biogeomorphological processes are an important component of dynamic intertidal systems. On rocky shores, the direct contribution of microorganisms, plants and animals to weathering and erosion is well known. There is also increasing evidence that organisms can alter rock breakdown indirectly, by moderating temperature and moisture regimes at the rock–air interface. These influences have been purported to represent mechanisms of bioprotection, by buffering microclimatic fluctuations associated with weathering processes such as wetting and drying and salt crystallization. However, virtually nothing has been done to test whether microclimatic buffering translates to differences in actual rock breakdown rates. Here we report a preliminary laboratory experiment to assess how an artificial canopy (chosen to represent seaweed) affects mechanical rock breakdown. Using a simplified and accelerated thermal regime based on field data from a rocky shore platform in southern England, UK, we find that breakdown (mineral debris release) of mudstone covered with a canopy is reduced by as much as 79% relative to bare rock after around 100 thermal cycles. Reduction in rock surface hardness (measured using an Equotip device) was also greater for bare rock (17%) compared to covered rock (10%) over this period. Measurements of salt crystal formation indicate that the mechanism driving these differences was a reduction in the frequency of crystallization events, via moisture retention and shading of the rock surface. Copyright © 2015 John Wiley & Sons, Ltd. 相似文献
11.
Large rock slope failures from near‐vertical cliffs are an important geomorphic process driving the evolution of mountainous landscapes, particularly glacially steepened cliffs. The morphology and age of a 2·19 × 106 m3 rock avalanche deposit beneath El Capitan in Yosemite Valley indicates a massive prehistoric failure of a large expanse of the southeast face. Geologic mapping of the deposit and the cliff face constrains the rock avalanche source to an area near the summit of ～8·5 × 104 m2. The rock mass free fell ～650 m, reaching a maximum velocity of 100 m s?1, impacted the talus slope and spread across the valley floor, extending 670 m from the base of the cliff. Cosmogenic beryllium‐10 exposure ages from boulders in the deposit yield a mean age of 3·6 ± 0·2 ka. The ～13 kyr time lag between deglaciation and failure suggests that the rock avalanche did not occur as a direct result of glacial debuttressing. The ～3·6 ka age for the rock avalanche does coincide with estimated late Holocene rupture of the Owens Valley fault and/or White Mountain fault between 3·3 and 3·8 ka. The coincidence of ages, combined with the fact that the most recent (AD 1872) Owens Valley fault rupture triggered numerous large rock falls in Yosemite Valley, suggest that a large magnitude earthquake (≥M7.0) centered in the south‐eastern Sierra Nevada may have triggered the rock avalanche. If correct, the extreme hazard posed by rock avalanches in Yosemite Valley remains present and depends on local earthquake recurrence intervals. Published in 2010 by John Wiley & Sons, Ltd. 相似文献
12.
A series of micro-erosion-meter sites on different rock types and in differing wind regimes was established and re-read after four years on two sites in the Larsemann and Vestfold Hills. These two oases in Eastern Antarctica are subjected to both wind abrasion and salt wedging. The measurements displayed bimodal distributions, indicating that both abrasion and single-grain detachment could be observed. Surface lowering rates of 0·015 and 0·022 mm a?1 were demonstrated for the Larsemann and Vestfold Hills, respectively. 相似文献
13.
Salt precipitation on the surface of porous media significantly affects water transport processes. Most studies on salt precipitation mainly focused on single salts, but in nature, salt precipitation usually occurs as mixtures. Consequently, information on the crystallization of salt mixtures and its effect on water transport remains scarce. This study investigated the precipitation of mixtures (the mass ratios of NaCl:Na2SO4 were 3:7, 5:5, and 7:3, respectively) of NaCl (typical efflorescence) and Na2SO4 (typical subflorescence) in the initially saturated sandy soil columns and its effect on evaporation and compared it with the cases of the two salts individually. The results showed that salt mixtures exhibited a mixed pattern of crystals including both efflorescence and subflorescence, and the efflorescence showed granular aggregation, unlike the mono-salts. The crystallization coverage of the salt mixtures was smaller than that of NaCl mono-salt; high (7:3) and low (5:5 and 3:7) proportions of NaCl led to larger and smaller crystallization coverage than that of Na2SO4 mono-salt, respectively. While the salt mixtures had less crystallization coverage than the mono-salts, they showed lower evaporation because the salt mixtures formed a denser crystallization structure of efflorescence-subflorescence-soil layer, this crystallization structure exhibited greater inhibition of water vapour diffusion, thus reducing evaporation. In addition, the crystallization of the salt mixtures with higher NaCl proportion afforded greater resistance of evaporation. The mixed crystallization pattern formed by the salt mixtures significantly enhances the crystallization resistance to evaporation. 相似文献
14.
Preliminary results from a continuing series of laboratory experiments designed to examine the combined effects of salt and frost weathering indicate that some salts greatly enhance the breakdown of rocks by frost. Samples of Ardingly Sandstone from southeast England were soaked in saturated solutions of sodium chloride or sodium sulphate and subjected to alternating cycles of freezing and thawing. Rapid disintegration of the sandstone occurred within twenty cycles, in each of the salt solutions. In contrast, samples subjected to freezing and thawing in deionized water suffered very little damage unless they were saturated under vacuum. When samples were subjected to twenty cycles of wetting and drying at temperatures above 0°C, those soaked in deionised water or sodium chloride suffered no appreciable damage but those soaked in sodium sulphate rapidly disintegrated. Tentative explanations of these results are offered. The enhancement of frost weathering by salt appears to have been overlooked by many writers yet it is likely to be an important geomorphological process in those areas of mid and high latitudes where rocks are saturated with sodium salts. 相似文献
15.
Transverse micro‐erosion meter (TMEM) stations were installed in rock slabs from shore platforms in eastern Canada. The slabs were put into artificial sea water for 1, 6 or 11 hours, representing high, mid‐ and low tidal areas, respectively. The TMEMs were used to record changes in surface elevation as the rocks dried during the remainder of the 12 h of a semi‐diurnal tidal cycle. A similar technique was used on the same rock types at intertidal TMEM stations in the field, as the rocks dried during low tide. Argillite and basalt surface contraction was from 0 to 0·04 mm: there was little surface expansion. Sandstones contracted by up to 0·03 mm in the field, but there was almost no contraction in the laboratory. Argillite and basalt contraction tended to be greatest in the upper intertidal zone, and to increase with rates of longer‐term surface downwearing, but there was little relationship with rock hardness or air temperature and humidity. Changes in elevation at the same points at TMEM stations in the laboratory and field were quite consistent from one tidal cycle to the next, but there were considerable variations within single tidal cycles between different points within each station. The data suggest that contraction within the elevational zone that is normally submerged twice a day by the tides is by alternate wetting and drying. Short‐term changes in elevation are generally low compared with annual rates of downwearing owing to erosion, but they may generate stresses that contribute to rock breakdown. Copyright © 2007 John Wiley & Sons, Ltd. 相似文献
16.
A multi‐method investigation of temperature,moisture and salt dynamics in tafoni (Tafraoute,Morocco) 
下载免费PDF全文
下载免费PDF全文 Harald Schnepfleitner Oliver Sass Stefanie Fruhmann Heather Viles Andrew Goudie 《地球表面变化过程与地形》2016,41(4):473-485
Despite numerous investigations and theoretical models, tafoni weathering is still not fully understood largely because of limited data available on temperature, moisture and salt regimes. We investigated tafoni developed in granite in the Tafraoute region, Morocco, through an exploratory, two‐week multi‐method field campaign. Temperatures were measured with iButtons and by means of infrared thermography; moisture distribution and progress were captured with handheld moisture sensors and with drilled‐in iButtons. Salts were analysed in drill dust samples from different positions and rock depths. The results derived from very different techniques mutually support one another. Salts and moisture are concentrated near the base of the investigated tafoni, probably due to a saturated pore water body around the base of rock tors. Salts are accumulated close to the rock surface in tafoni, but not on the surrounding rock surfaces. A clear correlation was found between moisture and salt contents. Within a tafone, areas of higher humidity also display increased salt concentration near the surface. The temperature/humidity records allied with ionic analyses suggest that sodium sulfate dominates and is likely to undergo frequent phase changes from thenardite to mirabilite and vice versa. Two pathways of salt transport in and around tafoni are assumed based on the data: infiltration with rainfall on the top and around tors and boulders, and capillary rise from saturated pore water bodies to the surface. Copyright © 2015 John Wiley & Sons, Ltd. 相似文献
17.
油藏岩石的孔隙连通性是反映流体渗流难易程度的重要参数,对渗透率、有效孔隙度等岩石物理参数的评价具有重要作用.连通的孔隙中,核磁共振(NMR)弛豫的交换会产生扩散耦合现象,可作为孔隙连通性的表征和探测方法.本文提出利用横向弛豫T 2-T 2脉冲序列测量岩石的扩散耦合现象.运用随机游走方法模拟多孔岩石的核磁共振响应特征,分析扩散耦合的影响因素,推导表征扩散耦合强度的弛豫交换速率计算公式.结果表明:孔隙间的扩散耦合强度与T 2-T 2脉冲序列的混合时间呈正相关性,基于双孔弛豫交换模型推导的弛豫交换速率计算公式能够准确表征双尺度孔隙系统的扩散耦合强度.在孔隙尺寸不满足快扩散条件时,会出现与扩散耦合无关的非对角峰信号.针对含多类型孔隙的碳酸盐岩模型,随混合时间的增加,扩散耦合强度变大,一维T 2谱的形态畸变程度加重,在T 2-T 2二维谱中,代表微裂缝、粒间小孔、溶蚀大孔的信号能量变化趋势不同,反映不同类型孔隙间的连通性存在差异.本文的分析与讨论丰富了核磁共振弛豫在岩石物理性质评价中的应用方向,对利用核磁共振评价复杂孔隙岩石的孔隙结构和连通性提供了新思路和新方法. 相似文献
18.
A laboratory simulation of salt weathering was used to ascertain the effects of sodium sulphate and sodium carbonate under ‘Negev’ conditions using a single immersion technique. Three main points were addressed: what are the grain size and textural characteristics of the debris liberated from limestones and a sandstone, what do scanning electron microscope observations of the weathered samples tell us about the decay processes involved, and how does the rate of debris liberation change during the course of 100 cycles? The grain size characteristics of the liberated debris tended to be multimodal and were related to the original petrological characteristics of the rock. Large amounts of fines were produced which are believed to be analogous to the ‘rock flour’ of arid areas. Blistering was also observed. Scanning electron microscope analysis revealed differences in the style of attack for different rock types and salt treatments, and revealed the pattern of salt crystallization in pores and the nature of cracking. The rate of debris liberation tended to decline or remain constant through time. The reasons for this remain obscure, but it is evident that diurnal cycles of temperature and humidity change can cause continuing rock weathering long after the initial input of salt to the rock has taken place. 相似文献
19.
Experiments are described in which chalk cubes were soaked in solutions of either sodium chloride, sodium sulphate, or magnesium sulphate at concentrations of 5·5 per cent and 12·5 per cent, or in a mixed solution of sodium chloride and sodium sulphate or in distilled water. After removal of excess liquid, the cubes were subjected to six freeze–thaw cycles with temperatures ranging from either +15 to ?10°C or +15 to ?30°C. The results confirm that frost weathering can be enhanced by the presence of certain salts, but the extent of weathering was much less than that previously reported for samples frozen totally immersed in the same liquids. Evidence is presented which suggests that salt crystallization is the major weathering process operative when non–immersed samples are frozen but a combination of frost and salt weathering operates when fully immersed samples are frozen. 相似文献
20.
To try to resolve the conflicts surrounding the influence of salts on frost weathering, chalk cubes were immersed, separately, in solutions of sodium chloride, sodium sulphate, and magnesium sulphate at concentrations of 5·5 per cent and 12·5 per cent, in a mixed solution of sodium chloride and sodium sulphate, and in distilled water. The cubes were subjected to six freeze-thaw cycles with temperatures ranging from either +15 to — 10°C or + 15 to — 30°C. The results confirm that frost weathering can be enhanced by the presence of certain salts, but the degree of enhancement depends both on the concentration and type of salt and on the intensity of the freeze-thaw regime. Some, but not all, of the results can be explained by the phase changes that occur during the freezing of the salt solutions. 相似文献