共查询到20条相似文献，搜索用时 328 毫秒
1.
An Experimental Study of Crack Coalescence Behaviour in Rock-Like Materials Containing Multiple Flaws Under Uniaxial Compression 总被引：4，自引：1，他引：3
Experiments on man-made flawed rock-like materials are applied extensively to study the mechanical behaviour of rock masses as well as crack initiation modes and crack coalescence types. A large number of experiments on specimens containing two or three pre-existing flaws were previously conducted. In the present work, experiments on rock-like materials (formed from a mixture of sand, plaster, limestone and water at mass ratio of 126:9:9:16) containing multiple flaws subjected to uniaxial compression were conducted to further research the effects of the layout of pre-existing flaws on mechanical properties, crack initiation modes and crack coalescence types. Compared with previous experiments in which only three types of cracks were found, the present experiments on specimens containing multiple flaws under uniaxial compression revealed five types of cracks, including wing cracks, quasi-coplanar secondary cracks, oblique secondary cracks, out-of-plane tensile cracks and out-of-plane shear cracks. Ten types of crack coalescence occurred through linkage among wing cracks, quasi-coplanar secondary cracks, oblique secondary cracks, out-of-plane shear cracks and out-of-plane tensile cracks. Moreover, the effects of the non-overlapping length and flaw angle on the complete stress–strain curves, the stress of crack initiation, the peak strength, the peak strain and the elastic modulus were also investigated in detail. 相似文献
2.
揭示双轴循环荷载条件下类玄武岩内裂纹起裂、扩展及岩桥贯通模式。配制类玄武岩相似材料,预制裂纹倾角=30、裂纹长度2a=20mm、裂纹厚度l=0.3mm的双裂纹,设计不同岩桥长度L、岩桥倾角试样,采用双轴压缩、双轴循环加卸载方式,研究裂纹扩展及岩桥贯通模式。试验结果表明:(1)双轴循环加卸载条件下,裂纹扩展-岩桥贯通过程可分为翼裂纹起裂、翼裂纹扩展和次生裂纹起裂及扩展、岩桥贯通3个阶段;(2)岩桥贯通类型可分为剪性贯通、张剪复合贯通和张性贯通3类。双轴压缩条件下,岩桥贯通模式可进一步划分为9种模式,双轴循环加卸载条件下,岩桥贯通模式可分为8种模式;(3)双轴循环加卸载试验比双轴压缩试验更易发生剪性贯通,且在部分试样岩桥处出现局部压碎隆起现象;(4)岩桥倾角和岩桥长度L对岩桥贯通模式影响显著,随着岩桥倾角的增大,岩桥贯通模式逐渐转变为剪性或张剪性贯通。双轴压缩条件下,岩桥长度增加,贯通模式由张剪复合贯通过渡为剪性贯通,而双轴循环加卸载试验则恰恰相反。 相似文献
3.
脆性岩石材料在压应力作用下常出现两类裂纹：翼型张拉裂纹和次生剪切裂纹。近场动力学是一种新型的无网格数值计算方法。在近场动力学理论中,采用积分形式的控制方程代替微分形式的控制方程使得该数值算法在断裂问题上具有独特的优势。将Mohr-Coulomb准则和最大主应力准则引入非普通“态”基近场动力学理论中,分别用于模拟材料常见的压剪和张拉破坏。这种扩展的非普通“态”基近场动力学可以有效地模拟脆性岩石材料在多种受力状态下的裂纹起裂、扩展和连接问题。通过5个不同的数值算例说明该数值算法在处理脆性岩石材料断裂问题的有效性和准确性。首先,通过模拟含圆孔的弹性板拉伸数值试验说明该数值算法的有效性和准确性。其次,数值模拟了简单三点弯曲试验以及不使用其他外部准则条件下动荷载作用下裂纹的分叉试验,所得结果与其他试验结果或数值结果相吻合,从而验证了该理论的有效性。然后,模拟了包含斜裂纹的巴西圆盘试验,裂纹扩展路径和计算所得的断裂韧度同样吻合于试验结果。最后,模拟了单轴压缩状态下,预制裂纹试样的裂纹扩展和连接问题。将该数值算法与试验结果对比表明,所提出的数值方法可以模拟和预测岩石类材料的张拉和压剪裂纹的起裂、扩展和连接行为。 相似文献
4.
Three-dimensional surface crack initiation and propagation in two kinds of heterogeneous rocks were numerically investigated via parallel finite element analysis using a supercomputer. Numerically simulated rock specimens containing a pre-existing flaw were subjected to uniaxial compression until failure. The initiation and propagation of wing cracks, anti-wing cracks, and shell-like cracks were reproduced by numerical simulations. The numerically simulated results demonstrate that the further propagation of wing cracks and shell-like cracks stop due to their wrapping (curving) behavior in three-dimensional spaces, even if the applied loads continue to increase. Furthermore, rock heterogeneity could significantly influence crack propagation patterns and the peak uniaxial compressive strengths of rock specimens. Moreover, anti-wing cracks only appeared in relatively heterogeneous rocks, and the peak uniaxial compressive strengths of the specimens were observed to depend on the inclination of the pre-existing flaw. Finally, the mechanism of surface crack propagation is discussed in the context of numerically simulated anti-plane loading tests, wherein it was identified that Mode III loading (anti-plane loading) does not lead to Mode III fracture in rocks due to their high ratio of uniaxial compressive strength to tensile strength. This finding could explain the lateral growth of an existing flaw in its own plane, which is a phenomenon that has not been observed in laboratory experiments. 相似文献
5.
Lekan Olatayo Afolagboye Jianming He Sijing Wang 《Geotechnical and Geological Engineering》2018,36(1):105-133
Crack initiation and coalescence behavior of rock or rock-like specimens containing artificial flaws under uniaxial compression have been subjects of intensive investigation in the past. Most of these investigations however focused on crack initiation and coalescence between two or more parallel flaws. Although there have been few experimental studies on non-parallel flaws, these studies did not address the influence of geometrical factors such as ligament length and ligament angle on the crack initiation and coalescence behavior of non-parallel flaws. To investigate whether the individual geometrical factors have similar effects on the crack initiation and coalescence behavior of both parallel and non-parallel flaws, we conducted uniaxial compression tests to investigate crack cracking and coalescence processes in rock like material containing two non-parallel flaws. The paper presents the influence of individual geometrical factors on the crack initiation process and coalescence pattern of non-parallel flaws. Initiation of primary first cracks from all the tips of the two flaws did not occur simultaneously in all the flaw configurations. The flaw configuration of the non-parallel flaws influences the crack initiation, crack trajectories and coalescence behavior. The crack coalescence pattern changes with an increasing ligament angle from indirect to shear crack or mixed tensile-shear crack to tensile crack coalescence. The chance of direct coalescence is reduced with an increase in ligament length. In conclusion, the crack initiation and coalescence behavior of prismatic rock-like specimens with non-parallel flaws, as influenced by the geometrical factors, are analogous to the cracking and coalescence pattern observed in specimens with parallel flaws. 相似文献
6.
单轴压缩条件下裂隙岩样冻融损伤破坏模式分析 总被引：8，自引：7，他引：1
以寒区裂隙岩体为研究对象,采用水泥砂浆类岩石材料制作具有不同几何特征的裂隙岩样,对预制的不同裂隙岩样进行冻融循环试验和单轴压缩试验,研究裂隙长度、裂隙倾角、裂隙数目以及冻融循环次数对试件贯通模式的影响。试验表明：裂隙岩体的几何特征以及冻融循环作用对岩体损伤破坏模式有较大影响。随着冻融循环次数的增加,岩样破裂面的破裂程度越来越严重,破坏模式也越来越复杂;裂隙倾角为30°的裂隙岩样,主要发生拉伸破坏,而裂隙倾角为60°的裂隙岩样,则表现为拉剪贯通,且双裂隙岩样岩桥间多出现压剪裂纹,对于裂隙倾角为90°的岩样,裂隙数目以及裂隙长度对其影响不大,均为劈裂破坏,且破坏面不一定为裂隙面;预制裂隙长度越大,越容易产生除了主拉裂纹以外的支裂纹（压裂纹）。研究结果可为寒区岩体工程建设及运营提供科学的参考。 相似文献
7.
Cracking and coalescence behavior in a rectangular rock-like specimen containing two parallel (stepped and coplanar) pre-existing open flaws under uniaxial compression load has been numerically studied by a parallel bonded-particle model, which is a type of bonded-particle model. Crack initiation and propagation from two flaws replicate most of the phenomena observed in prior physical experiments, such as the type (tensile/shear) and the initiation stress of the first crack, as well as the coalescence pattern. Eight crack coalescence categories representing different crack types and trajectories are identified. New coalescence categories namely “New 1” and “New 2”, which are first observed in the present simulation, are incorporated into categories 3 and 4, and category 5 previously proposed by the MIT Rock Mechanics Research Group, respectively. The flaw inclination angle (β), the ligament length (L) (spacing between two flaws) and the bridging angle (α) (inclination of a line linking up the inner flaw tips, between two flaws) have different effects on the coalescence patterns, coalescence stresses (before, at or post the peak stress) as well as peak strength of specimens. Some insights on the coalescence processes, such as the initiation of cracks in the intact part of specimens at a distance away from the flaw tips, and coalescence due to the development and linkage of a number of steeply inclined to vertical macro-tensile cracks are revealed by the present numerical study. 相似文献
8.
Crack evolution is initiated by the occurrence of tensile wing cracks and is then further promoted due to the crack coalescence caused by the extension of a central tensile crack segment between two relatively adjacent flaws. To understand such progressive failures in rock, a parallelized peridynamics coupled with a finite element method is utilized. Through this method, the initiation position of tensile wing cracks is observed with respect to varying inclination angles of a flaw, and then its corresponding shifting mechanism is investigated. In addition, the phenomenon of the position shifting being sensitive to various flaw shapes is discussed. Moreover, it is observed that the inclination angle of a central flaw affects the initiation position of other flaws; therefore, the initiation positions of tensile wing crack emanating from other neighboring flaws are analyzed with their angles. Following tensile wing cracks, a central tensile crack segment occurs in the bridging region between a central flaw and other neighboring flaws; the developmental patterns caused by the crack segment are discussed as well. Finally, the role a central tensile crack segment plays in the formation of crack coalescence and specimen failure is investigated in detail. The numerical results in this paper demonstrate good fidelity with established physical test results and complement them, thereby expanding the understanding of fracturing morphology in rock specimens with various flaws. 相似文献
9.
干湿交替作用后砂岩破裂过程实时观测与分析 总被引：1，自引：0，他引：1
采用岩石破裂全过程的细观力学试验系统进行了天然状态及干湿交替作用后的完整和含预制圆孔砂岩试件的单轴压缩破裂试验。利用显微镜观察了砂岩裂纹萌生、扩展以及试件的失稳破坏过程。经过干湿交替作用后岩样更容易在较低的应力状态下发生裂纹的扩展,并且裂纹扩展的初始阶段一般表现为拉破裂。完整试件的裂纹是随机性的三维扩展,而有预制圆孔试件一般是从预制圆孔周边开始扩展。天然状态下的预制圆孔试件在起裂时从圆孔的压应力集中区产生剪切裂纹;而干湿交替作用后,起裂时可能先从拉应力集中区产生拉裂纹,并且裂纹演化过程更为复杂一些,破裂形式多样化。与天然状态相比,经过干湿循环作用后的砂岩破坏脆性降低,强度等力学参数也随干湿交替次数增加而逐渐降低。 相似文献
10.
共面非贯通裂隙的贯通机制对于确定外载下岩质边坡的滑动面位置及滑动面综合抗剪强度至关重要。采用预制共面非贯通裂隙石膏模型试样单轴静动载对比试验,对不同裂隙倾角共面排列裂隙的扩展、贯通过程进行了观测,研究显示：共面非贯通裂隙不同倾角下的贯通模式存在较大差异,裂隙倾角为0o～35o时以裂隙面发生闭合变形为主;45o～65o时裂隙间较易出现剪切型破坏模式;75o～90o预制裂隙面较难产生滑动,裂隙试样主要产生劈裂形式的破坏。动载下预制裂隙试样裂尖翼裂纹及次生共面裂纹起裂后易朝原起裂方向快速发展;易在两预制裂隙内端部产生直接贯通,这与静载下岩桥处的贯通常通过分支裂纹拐折扩展、相连不同。含共面非贯通裂隙试样在裂隙倾角为35o左右时强度呈现最小值,这与贯通性裂隙试样裂隙倾角为60o左右呈现最小值相差较大,这是因为裂隙面摩擦强度没来得及发挥作用所致。因此,含非贯通节理裂隙岩体的综合抗剪强度公式应引入强度发挥系数,以充分考虑岩桥胶结强度与裂隙面摩擦强度不能同步发挥作用的破坏本质。 相似文献
11.
模拟岩石压剪状态下主次裂纹萌生开裂的扩展有限元法 总被引：1，自引：0，他引：1
压剪应力状态下,岩石类材料中常见两类裂纹：翼型张拉裂纹和次生压剪裂纹。基于扩展有限元方法（XFEM）,提出了模拟压剪裂纹面作用机制的扩展有限元位移增强方案,并给出了扩展有限元法分叉裂纹处理方法,分别用最大周向拉应力准则和Mohr-Coulomb准则判断张拉裂纹和压剪裂纹的萌生和扩展。基于Matlab平台编写了数值计算程序Betaxfem 2D,通过两个算例对所提方案进行了验证,所得结果与有限元法（FEM）计算结果吻合很好。模拟了单轴压缩载荷下含预制闭合裂纹试件的裂纹分叉、扩展过程,与试验结果的对比表明,所提方案可以模拟和预测岩石类材料张拉、压剪交互分叉裂纹的萌生和扩展行为。 相似文献
12.
Zhao Yusong Gao Yongtao Wu Shunchuan Chen Long Zhang Chengliang 《Acta Geotechnica》2021,16(10):3087-3113
Open flaws without any filling material are common fracture structures in real rock. To study the failure characteristics of this fracture structure, small-scale rock-like samples with single internal 3D open flaws are prepared, and uniaxial compression tests are conducted. Digital image correlation (for surface strain and failures) and acoustic emission (for internal microfracture behaviors) monitoring technologies are also employed to analyze the flaws. The test results are verified through numerical simulations. Different inclination angles of the internal preset flaws are found to have little influence on the strength of the samples, and the surface and internal secondary failures of the samples exhibit very different development processes and distributions. The particle displacement trend method is applied to explain the initiation mechanism of secondary cracks, but the corresponding analyses are only reasonable if particle information along the y-axis is considered. Therefore, the particle information in the y-axis is incorporated by defining new 2D sections (with y-axis) or partial 3D models. Based on these research methods, the initiation mechanism of secondary cracks is reasonably explained, and the influence of the preset flaw thickness on the particle displacement trend fields and secondary failures in surrounding rocks can be discussed. Finally, the simulation results prove that the Mode II and III failures are usually coupled, and direct Mode III failures (displacement of two parts of rock parallel to each other and in opposite directions) only occur in the front and rear surrounding rocks of the preset flaw.
相似文献13.
为了研究节理对锚固岩体力学特征和失稳损伤演化的影响,采用对锚固贯通节理岩体进行室内剪切试验和PFC2D数值模拟的方法,研究不同节理倾角下锚固贯通节理岩体剪切性能的作用机制和破坏模式,研究结果表明:（1）随着节理倾角变化,贯通节理岩体呈现出不同的破坏形式,锚固贯通节理岩体的抗剪强度与剪切位移曲线并不是呈线性增长,而是呈"双驼峰"趋势。（2）锚固体系在剪切试验的过程中,节理面颗粒的接触方位角会发生一定程度的改变,主要集中在锚杆和节理倾角附近。（3）锚固体系在剪切试验的过程中,会因为颗粒间黏结键的断裂生成裂纹,裂纹数生成的越少,其抗剪强度越高,裂纹分为张拉裂纹和剪切裂纹,并且张拉裂纹的数量要远远大于剪切裂纹的数量。研究结论可用于实际工程破坏模式的预测和岩体工程稳定性评价。 相似文献
14.
Ioannis Rigopoulos Basilios Tsikouras Panagiotis Pomonis Konstantin Hatzipanagiotou 《Rock Mechanics and Rock Engineering》2013,46(5):1061-1072
This paper investigates the influence of the petrographic characteristics of mafic ophiolitic rocks on the initiation and propagation of microcracks during uniaxial compression. The microcrack patterns of a troctolite and a diorite, collected from the Pindos and Othrys ophiolites (Greece), respectively, were analysed. Thorough observation and quantification of microcracks before and after the uniaxial compression test were conducted. Combined fluorescent and polarised microscopy of polished thin sections, together with digital image analysis, indicated that the intragranular microcracks are the dominating crack type in both loaded and unloaded specimens, only in terms of their total number and length. On the other hand, the intergranular and transgranular cracks seem to grow more readily compared to the intragranular cracks, implying that the longer microcracks grow more extensively under stress. The orientation of most of the newly formed intragranular and transgranular microcracks is nearly parallel to the loading direction; however, some of the randomly oriented transgranular cracks have probably been formed during the propagation of intergranular cracks. In the troctolite, the frequency of the intragranular microcracks decreases in the olivine crystals after the uniaxial compression test due to their partial serpentinisation, which increases their resistance to brittle deformation. In the plagioclase crystals of the troctolite, microcracks are often oriented parallel to the cleavage planes, implying that such crystallographic orientations act as planes of weakness. On the contrary, the plagioclase crystals of the diorite are mainly crossed by randomly oriented microcracks, presumably due to their high degree of alteration. In the diorite, the evolution of microcracks is substantially controlled by the two perfect cleavages of amphibole. The failure of a rock occurs as a result of the growth, interaction and coalescence of a great number of pre-existing and newly formed intragranular and transgranular microcracks. The petrographic and microcrack analysis may assist in the selection of the most suitable rock type for various construction applications. 相似文献
15.
含交叉裂隙岩体相似材料试件力学性能单轴压缩试验 总被引：3，自引：0，他引：3
以相似材料制作含交叉裂隙岩体试件,考虑主裂隙与加载方向之间角度变化及主、次裂隙之间角度变化制作20组试件,对试件进行单轴压缩试验,研究交叉裂隙对岩体破坏模式及力学特性的影响。研究表明,主裂隙与加载方向呈0°及90°时,试件破坏主要为沿次裂隙扩展的剪切型破坏;当主裂隙与加载方向呈30°及45°时,试件破坏主要是沿主裂隙扩展所致的剪切型破坏;主裂隙角度一致情况下,大部分含交叉裂隙岩体破坏强度高于含单向裂隙岩体,含交叉裂隙岩体试件应力-应变曲线峰后下降斜率比含单向裂隙岩体大;主裂隙角度一致情况下,当次裂隙与主裂隙呈45°夹角左右时,岩体试件强度较低,当次裂隙与主裂隙呈30°及90°夹角左右时,岩体试件强度较高。 相似文献
16.
Strength,fragmentation and fractal properties of mixed flaws 总被引：1，自引：1，他引：0
Experiments on Portland cement samples containing mixed flaws are conducted to investigate the strength, fragmentation and fractal properties. Flaw geometry is a new combination of two edge-notched flaws and an imbedded flaw, which is different from those in the previous studies, where parallel or coplanar flaws are used. The physical implications of the shear-box test applied to result to rock slopes are studied. The physical and analytical fragmentation characteristics of preflawed samples are analyzed through the sieve test and fractal theory, respectively. Three different patterns of tensile cracks and shear cracks are observed. A sliding crack model is presented to elucidate the brittle failure flaws. In all of the cases of the shear-box tests, the coalescence is produced by the linkage of shear cracks, and two types of coalescence (Type C1 and Type C2) have been classified, which tend to confirm the observations from the numerical model and field of jointed rock slopes. The shear strength is a function of the flaw geometry and the shear–normal stress ratio. The result of sieve tests indicates that the fragment size distribution of fragments has the fractal property, providing a physical understanding of the fragmentation mechanism. The fragments under the shear-box test have fractal dimensions between 2.2 and 2.6, which are larger than those under the compression test but similar to those in the fault cores. The fragmentation in the case of Type C2 has a smaller fractal dimension, corresponding to a larger shear strength. 相似文献
17.
Evolution of Rock Cracks Under Unloading Condition 总被引：2，自引：0，他引：2
Underground excavation normally causes instability of the mother rock due to the release and redistribution of stress within the affected zone. For gaining deep insight into the characteristics and mechanism of rock crack evolution during underground excavation, laboratory tests are carried out on 36 man-made rock specimens with single or double cracks under two different unloading conditions. The results show that the strength of rock and the evolution of cracks are clearly influenced by both the inclination angle of individual cracks with reference to the unloading direction and the combination geometry of cracks. The peak strength of rock with a single crack becomes smaller with the inclination angle. Crack propagation progresses intermittently, as evidenced by a sudden increase in deformation and repeated fluctuation of measured stress. The rock with a single crack is found to fail in three modes, i.e., shear, tension–shear, and splitting, while the rock bridge between two cracks is normally failed in shear, tension–shear, and tension. The failure mode in which a crack rock or rock bridge behaves is found to be determined by the inclination angle of the original crack, initial stress state, and unloading condition. Another observation is that the secondary cracks are relatively easily created under high initial stress and quick unloading. 相似文献
18.
岩体内部赋存的裂隙很多表现为折线型,为探究这类岩体的断裂机制,制备含折线型裂隙砂岩试件并对其进行单轴压缩试验。采用数字图像相关(DIC)方法计算加载过程中的变形场演化,根据新生裂纹两侧的位移差异识别裂纹类型;运用扩展有限元法(XFEM)模拟断裂过程,根据应力分布特征解释翼型裂纹起裂与扩展机制。DIC计算结果表明,新生裂纹处出现应变局部化带,裂纹两侧发生相对分离;含直线型和折线型裂隙砂岩试件的翼型裂纹分别萌生于预制裂隙端部以及折角处,这是因为裂隙几何形态会改变拉应力集中位置;含折线型裂隙砂岩试件的起裂应力小于含直线型裂隙砂岩试件,这是因为相同加载条件下前者的最大拉应力值更大;这2类试件的裂纹扩展均是由于裂纹尖端集中的拉应力引起的,裂纹依然呈张开状态;裂隙几何形态未改变试件的最终破坏模式,均表现为对角剪切破坏。 相似文献
19.
Cracking processes have been extensively studied in brittle rock and rock-like materials. Due to the experimental limitations and the complexity of rock texture, details of the cracking processes could not always be observed and assessed comprehensively. To contribute to this field of research, a numerical approach based on the particle element model was used in present study. It would give us insights into what is happening to crack initiation, propagation and coalescence. Parallel bond model, a type of bonded-particle model, was used to numerically simulate the cracking process in rock-like material containing a single flaw under uniaxial vertical compression. The single flaw’s inclinations varied from 0° to 75° measured from the horizontal. As the uniaxial compression load was increased, multiple new microcracks initiated in the rock, which later propagated and eventually coalesced into longer macrocracks. The inclination of the pre-existing flaw was found to have a strong influence on the crack initiation and propagation patterns. The simulations replicated most of the phenomena observed in the physical experiments, such as the type, the initiation location and the initiate angle of the first cracks, as well as the development of hair-line cracks, which later evolved to macrocracks. Analyses of the parallel bond forces and displacement fields revealed some important mechanisms of the cracking processes. The first cracks typically initiated from the tensile stress concentration regions, in which the tensile stress was partially released after their initiation. The tensile stress concentration regions subsequently shifted outwards close to the propagating tips of the first cracks. The initiation and propagation of the first cracks would not significantly influence the compressive stress singularity at the flaw tips, which was the driving force of the initiation of secondary cracks. The initiation of microcracking zone consisting almost exclusively of micro-tensile cracks, and that of microcracking zone consisting of micro-tensile cracks and mixed micro-tensile and shear cracks, were found to be correlated with two distinct types of displacement fields, namely type I (DF_I) and type II (DF_II), respectively. 相似文献
20.
三叉裂隙是自然界普遍存在的一种岩体缺陷形式,其对岩体的力学特性有重要影响。对含预制三叉裂隙的水泥砂浆试样进行室内单轴压缩试验,配合使用摄像机拍摄裂纹的起裂、扩展、贯通过程,通过数字图像技术处理获取试样的应变场云图,并结合PFC2D程序研究不同?、? 条件下试样的强度特征、裂纹模式和裂纹演化扩展规律。研究表明：三叉裂隙对试样单轴抗压强度有明显的削弱作用。当? 恒定为120°时,试样在? = 30°时达到最大抗压强度;当? 恒定为90°时,随?增大,试样抗压强度呈先减小后增大的趋势,且当? = 45°时达到最大抗压强度。试样产生的裂纹可分为3类,分别是张拉型裂纹(Ⅰ型裂纹)、剪切型裂纹(Ⅱ型裂纹)、混合型裂纹(Ⅲ型裂纹)。这3类裂纹通常从裂隙尖端开始产生,并且Ⅰ型裂纹沿加载方向扩展,通常未扩展至试样边界;Ⅱ型和Ⅲ型裂纹通常与加载方向呈一定角度扩展至试样边界。通过对裂纹的几何形态和组成宏观裂纹的微裂纹成分的分析,得知导致含三叉裂隙试样在单轴压缩条件下失效的是张拉破坏。数字图像技术得到的应变云图表明,当载荷达到一定阶段,裂隙尖端出现应力集中,微破裂开始发育并聚集成微破裂区,微破裂区扩大产生宏观裂纹。通过对主应变和剪应变云图分析,发现导致试样失效的是张拉破坏,剪应变在裂纹扩展过程中的影响较小。 相似文献