共查询到20条相似文献，搜索用时 15 毫秒
1.
为准确建立海底地声模型,本文探讨地声模型的基本组成和基本结构。通过样品实验室测量,分析南海海底表层沉积物的密度、孔隙度与声速随着埋深变化的关系,得出海底实际存在的低声速表面–声速缓慢变化类型、低声速表面–声速增大类型、高声速表面–声速缓慢变化类型和高声速表面–声速增大类型4种典型地声结构;对比钻探测量,分析黄海海底沉积物的密度、孔隙度与声速随埋深变化关系,得出海底地声模型分层特征与地声结构组合特征。研究表明,地声模型可以归结为4种基本地声结构的组合,通过与底层海水声速、同层内声速剖面以及与上层海底沉积物下表面声速的比较,可以建立各种海底地声模型;基于实验室测量法建立的地声模型可以作为参考地声模型,但需要考虑实际海底温度和压力梯度以及海底沉积物的频散特性等,借助于声速比校正法和频散性理论模型进行计算及修正。 相似文献
2.
3.
Arne Schnack-Friedrichsen Angela M. Davis Jim D. Bennell Dei G. Huws 《Marine Georesources & Geotechnology》2001,19(4):221-243
The interdependence between the seismo-acoustic properties of a marine sediment and its geotechnical/physical parameters has been known for many years, and it has been postulated that this should allow the extraction of geotechnical information from seismic data. Though in the literature many correlations have been published for the surficial layer, there is a lack of information for greater sediment depths. In this article, a desktop study on a synthetic seafloor model illustrates how the application of published near-surface prediction equations to subsurface sediments (up to several tens of meters burial depth) can lead to spurious predictions. To test this further, acoustic and geotechnical properties were measured on a number of sediment core samples, some of which were subjected to loading in acoustically-equipped consolidation cells (oedometers) to simulate greater burial depth conditions. For low effective pressures (representing small burial depths extending to around 10 meters subsurface), the general applicability of established relationships was confirmed: the prediction of porosity, bulk density, and mean grain size from acoustic velocity and impedance appears generally possible for the investigated sedimentary environments. As effective pressure increases through, the observed relationships deviate more and more from the established ones for the near-surface area. For the samples tested in this study, in some instances increasing pressure even resulted in decreasing velocities. There are several possible explanations for this abnormal behavior, including the presence of gas, overconsolidation, or bimodal grain size distribution. The results indicate that an appropriate depth correction must be introduced into the published prediction equations in order to obtain reliable estimates of physical sediment properties for greater subsurface depths. 相似文献
4.
海底浅表层（小于1 m）沉积物的物理性质,如粒度、孔隙度、密度等是海洋沉积学研究和海洋工程地质分析的重要内容,目前主要基于有限的海底取样或原位测试获取这些沉积物的物理性质。浅地层剖面是基于声学信号（频率几千赫兹）在沉积物中的传播得到可反映沉积地层结构的数据,其中的一些声学参数,如海底反射系数、波阻抗等与沉积物物理性质密切相关。如何充分而有效地利用浅地层剖面资料,反演得到剖面覆盖区海底浅表层沉积物的物理性质参数,极具科学意义和应用价值,且基于声学属性反演沉积物物理性质是当前研究的热点。为此,本文基于渤海LD16-3CEPA至LD10-1PAPD路由段的浅地层剖面数据和海底表层沉积物的实测物理参数,利用Biot-Stoll模型建立研究区海底反射系数和沉积物物理性质之间的关系,并基于浅地层剖面数据计算得到的海底反射系数,反演了研究区海底浅表层沉积物的孔隙度、密度、平均粒径等物理性质参数。其中反演的孔隙度、密度、平均粒径与实测孔隙度、密度、平均粒径基本相符,偏差度基本都在20%的偏差范围内,表明该反演方法在该区的应用是可行的。 相似文献
5.
Arne Schnack-Friedrichsen Angela M. Davis Jim D. Bennell Dei G. Huws 《Marine Georesources & Geotechnology》2013,31(4):221-243
The interdependence between the seismo-acoustic properties of a marine sediment and its geotechnical/physical parameters has been known for many years, and it has been postulated that this should allow the extraction of geotechnical information from seismic data. Though in the literature many correlations have been published for the surficial layer, there is a lack of information for greater sediment depths. In this article, a desktop study on a synthetic seafloor model illustrates how the application of published near-surface prediction equations to subsurface sediments (up to several tens of meters burial depth) can lead to spurious predictions. To test this further, acoustic and geotechnical properties were measured on a number of sediment core samples, some of which were subjected to loading in acoustically-equipped consolidation cells (oedometers) to simulate greater burial depth conditions. For low effective pressures (representing small burial depths extending to around 10 meters subsurface), the general applicability of established relationships was confirmed: the prediction of porosity, bulk density, and mean grain size from acoustic velocity and impedance appears generally possible for the investigated sedimentary environments. As effective pressure increases through, the observed relationships deviate more and more from the established ones for the near-surface area. For the samples tested in this study, in some instances increasing pressure even resulted in decreasing velocities. There are several possible explanations for this abnormal behavior, including the presence of gas, overconsolidation, or bimodal grain size distribution. The results indicate that an appropriate depth correction must be introduced into the published prediction equations in order to obtain reliable estimates of physical sediment properties for greater subsurface depths. 相似文献
6.
The Bering Sea shelf and Chukchi Sea shelf are believed to hold enormous oil and gas reserves which have attracted a lot of geophysical surveys. For the interpretation of acoustic geophysical survey results, sediment sound velocity is one of the main parameters. On seven sediment cores collected from the Bering Sea and Chukchi Sea during the 5th Chinese National Arctic Research Expedition, sound velocity measurements were made at 35, 50, 100, 135, 150, 174, 200, and 250 k Hz using eight separate pairs of ultrasonic transducers. The measured sound velocities range from 1 425.1 m/s to 1 606.4 m/s and are dispersive with the degrees of dispersion from 2.2% to 4.0% over a frequency range of 35–250 k Hz. After the sound velocity measurements, the measurements of selected geotechnical properties and the Scanning Electron Microscopic observation of microstructure were also made on the sediment cores. The results show that the seafloor sediments are composed of silty sand, sandy silt, coarse silt, clayey silt, sand-silt-clay and silty clay. Aggregate and diatom debris is found in the seafloor sediments. Through comparative analysis of microphotographs and geotechnical properties, it is assumed that the large pore spaces between aggregates and the intraparticulate porosity of diatom debris increase the porosity of the seafloor sediments, and affect other geotechnical properties. The correlation analysis of sound velocity and geotechnical properties shows that the correlation of sound velocity with porosity and wet bulk density is extreme significant, while the correlation of sound velocity with clay content, mean grain size and organic content is not significant. The regression equations between porosity, wet bulk density and sound velocity based on best-fit polynomial are given. 相似文献
7.
The sediment–water interface is usually marked by an increase in acoustic impedance and is therefore displayed in a seismic
section as a positive polarity reflection. Here, we use the term “seabed phase reversal” to describe areas of seafloor which
are instead expressed as a negative polarity reflection in seismic data. We describe in detail a number of examples of seafloor
phase reversals and use a simple one-dimensional geophysical model to test the hypothesis that they are the result of the
presence of gas within the seafloor sediment. Our examples are all related to seismically imaged mud volcanoes located within
the South Caspian Sea. Sections of phase-reversed seafloor at the summit area of these volcanoes have been mapped to reveal
the existence of seafloor mud pools (salses) and recently erupted mud flows which show a strong similarity to smaller-scale
features at onshore volcanoes in Azerbaijan. Synthetic geophysical modelling indicates that under the physical conditions
likely to occur when the seabed sediment is gas-bearing, the seafloor will be expressed as a strong negative polarity reflection.
Unlike other indicators of seafloor gas, such as pockmarks, which merely record the transient expulsion of fluids from sedimentary
basins, seafloor phase reversals indicate the presence of gas in marine sediment at the time of survey acquisition. They therefore
are of significance to engineering and site survey operations as well as the identification of biological communities and
gas flux calculations. 相似文献
8.
In recent years, increasing attention is being given to investigating the relationships between seafloor echo strength and
sediment type. This aspect was assessed in a course of a marine survey conducted in Jiaozhou Bay near the city of Qingdao,
China, where various sediment types are known to exist. Multi-beam echo data and sediment samples were acquired, processed
and analyzed. The findings demonstrate that multi-beam echo strengths are strongly related to seabed types such as rock, sand
and clay. Thus, echo strength increases progressively with the increase in sand content in gravely, sandy, and clayey sediments.
However, echo strength is more sensitive to changes in sand content in fine-grained sediment and less sensitive in coarse-grained
sediment. Also, high shell content of sediments greatly enhances the acoustic reflection. These findings help to predict seafloor
sediment types by analyzing echo strength. 相似文献
9.
We report on a marine electromagnetic (EM) survey across two portions of the New Jersey continental margin that have been previously shown to contain buried paleo-channels. The EM method used provides bulk porosity estimates to depths of around 20 m below the seafloor and is thus able to place porosity constraints on the nature of the channel infill and the contrast in physical properties across the channel boundaries. Our data show that a key condition for the channels to have an electrical signature is that they incise an underlying regional unconformity, R, thought to represent a subaerially eroded surface, exposed during the late Wisconsinan glaciation. Channels that cut R are seen through increases in apparent porosity. Another seismically imaged channel sequence, which lies within the outer-shelf sediment wedge sequence above R, does not have an electrical signature, indicating that the sediments above and below the channel boundaries have similar physical properties. 相似文献
10.
Experimental airborne electromagnetic (AEM) survey data collected in Cape Cod Bay are used to derive continuous profiles of water depth, electrical depth, water conductivity, and bottom sediment conductivity. Through a few well-known empirical relationships, the conductivities are used, in turn, to derive density, porosity, sound speed, and acoustic reflectivity of the ocean bottom. A commercially available Dighem III AEM system was used for the survey without any significant modification. The helicopter-borne system operated at 385 and 7200 Hz; both were in a horizontal coplanar configuration. The interpreted profiles show good agreement with available ground truth data. Where no such data are available, the results appear to be very reasonable. Compared with the shipborne electrode array method, the AEM method can determine the necessary parameters at a much higher speed with a better lateral resolution over a wide range of water depths from 0 to perhaps 100 m. The bottom sediment conductivity that can be measured by the AEM method is closely related to physical properties of sediments, such as porosity, density, sound speed, and, indirectly, sediment types that might carry broad implications for various offshore activities. 相似文献
11.
12.
《Marine and Petroleum Geology》2012,36(1):105-115
This article provides new constraints on gas hydrate and free gas concentrations in the sediments at the margin off Nova Scotia. Two-dimensional (2-D) velocity models were constructed through simultaneous travel-time inversion of ocean-bottom seismometer (OBS) data and 2-D single-channel seismic (SCS) data acquired in two surveys, in 2004 and 2006. The surveys, separated by ∼5 km, were carried out in regions where the bottom-simulating reflection (BSR) was identified in seismic reflection datasets from earlier studies and address the question of whether the BSR is a good indicator of significant gas hydrate on the Scotian margin. For both datasets, velocity increases by 200–300 m/s at a depth of approximately 220 m below seafloor (mbsf), but the results of the 2006 survey show a smaller velocity decrease (50–80 m/s) at the base of this high-velocity layer (310–330 mbsf) than the results of the 2004 survey (130 m/s). When converted to gas hydrate concentrations using effective medium theory, the 2-D velocity models for both datasets show a gas hydrate layer of ∼100 m thickness above the identified BSR. Gas hydrate concentrations are estimated at approximately 2–10% for the 2006 data and 8–18% for the 2004 survey. The reduction in gas hydrate concentration relative to the distance from the Mohican Channel structure is most likely related to the low porosity within the mud-dominant sediment at the depth of the BSR. Free gas concentrations were calculated to be 1–2% of the sediment pore space for both datasets. 相似文献
13.
A possible approach to, and preliminary results of, amplitude calibration of acoustic signals backscattered from an ADCP moored at the bottom of the near-shelf zone of the Black Sea is considered. The aim of this work is to obtain vertical profiles of acoustic scattering signal levels, showing the real characteristics of the volume content of suspended sediments in sea water in units of conventional acoustic turbidity for a given signal frequency. In this case, the assumption about the intervals of maximum acoustic transparency and vertical homogeneity of the marine environment in long-term series of ADCP measurements is used. According to this hypothesis, the intervals of the least values of acoustic backscattered signals are detected, an empirical transfer function of the ADCP reception path is constructed, and it is calibrated. Normalized sets of acoustic backscattered signals relative to a signal from a level of conventionally clear water are obtained. New features in the behavior of vertical profiles of an acoustic echo-signal are revealed due to the calibration. The results of this work will be used in subsequent analysis of the vertical and time variations in suspended sediment content in the near-shelf zone of the Black Sea. 相似文献
14.
The physics of gas chimney and pockmark formation,with implications for assessment of seafloor hazards and gas sequestration 总被引：2，自引：0，他引：2
Pockmarks form where fluids discharge through seafloor sediments rapidly enough to make them quick, and are common where gas is present in near-seafloor sediments. This paper investigates how gas might lead to pockmark formation. The process is envisioned as follows: a capillary seal traps gas beneath a fine-grained sediment layer or layers, perhaps layers whose pores have been reduced in size by hydrate crystallization. Gas accumulates until its pressure is sufficient for gas to invade the seal. The seal then fails completely (a unique aspect of capillary seals), releasing a large fraction of the accumulated gas into an upward-propagating gas chimney, which displaces water like a piston as it rises. Near the seafloor the water flow causes the sediments to become “quick” (i.e., liquefied) in the sense that grain-to-grain contact is lost and the grains are suspended dynamically by the upward flow. The quickened sediment is removed by ocean-bottom currents, and a pockmark is formed. Equations that approximately describe this gas–piston–water-drive show that deformation of the sediments above the chimney and water flow fast enough to quicken the sediments begins when the gas chimney reaches half way from the base of its source gas pocket to the seafloor. For uniform near-surface sediment permeability, this is a buoyancy control, not a permeability control. The rate the gas chimney grows depends on sediment permeability and the ratio of the depth below seafloor of the top of the gas pocket to the thickness of the gas pocket at the time of seal failure. Plausible estimates of these parameters suggest gas chimneys at Blake Ridge could reach the seafloor in less than a decade or more than a century, depending mainly on the permeability of the deforming near-surface sediments. Since these become quick before gas is expelled, gas venting will not provide a useful warning of the seafloor instabilities that are related to pockmark formation. However, detecting gas chimney growth might be a useful risk predictor. Any area underlain by a gas chimney that extends half way or more to the surface should be avoided. 相似文献
15.
原位测量技术在黄海沉积声学调查中的应用 总被引：11，自引：3，他引：8
介绍了最新研制的基于液压驱动贯入的自容式海底沉积声学原位测量系统及其在南黄海中部海底沉积声学调查中的应用。该系统可以实现对海底沉积物声速和声衰减系数进行原位测量,通过液压驱动装置将四根声学探杆匀速贯入到海底沉积物中,减少了对沉积物的扰动,可按照预设的工作参数在海底全自动工作,无需甲板上人员实时控制,采集的声波信号自容式存储于存储单元。系统工作水深为500 m,测量深度为1 m,测量频率为30 kHz,采样频率为10 MHz。使用该系统在南黄海中部获得了40个站位不同类型沉积物的声学特性原位测量数据,并使用CTD剖面仪对该系统声速测量进行了标定,相对误差均小于0.5%,表明该系统测量数据准确、可靠。 相似文献
16.
本文通过对南海海底沉积物样品的声学物理参数和沉积粒度特征统计分析,发现了高、低含砂量沉积物的声学物理特征存在明显差异,建立了海底沉积物的含砂量与压缩波速度、孔隙度、含水量和密度等经验公式,分析了含砂量变化与沉积物的体积压缩模量和密度变化的关系,从声速理论基础上阐明了含砂量变化引起沉积物压缩波速度变化的内在原因是含砂量变化引起了体积压缩模量和密度发生了变化,说明了含砂量增大引起沉积物压缩波速度增大的内在原因是含砂量增大引起了体积压缩模量变化量大于密度变化量,从而在数据统计和理论分析结合基础上,论证了含砂量是影响海底沉积物压缩波速度的重要因素之一。这一研究对声学方法反演海底沉积物粒度参数和沉积物类型、地声参数转换模型的建立,以及对水声反演海底和海底资源勘探等方面都具有重要理论意义和应用价值。 相似文献
17.
Acoustic environment and physico‐mechanical properties of the shelf seabed off the pearl river mouth
Abstract The vast shallow sea off the Pearl River mouth in the northern South China Sea is an important prospecting area for offshore oil development. In recent years, the authors have investigated acoustic and geotechnical characteristics of marine sediments in this area. An intercalated layer of low sound velocity and low compressive strength has been found within the seabed, in which the median diameter of sediment grains is fine and the sound velocity is 100–200 m/s lower than that of the overlying and underlying layers. The minimum unconfined compressive strength of this layer is 0.075 kg/cm2, which is lower than that of the over‐ and underlying layers by an order of magnitude. Such an intercalation often constitutes a threat to the stability of shallow foundation soil. In case of overloading, the layer may be weakened, and seafloor sliding between different sediment layers may occur. The regional distribution of these kinds of weak intercalations of low sound velocity may be traced by a subbottom profiler and by means of sediment acoustical investigations. Correlation between the gray level of a layer on subbottom profile records and physical properties of the layer (including sound velocity and reflectivity) suggests that the layer of sufficient bearing capacity must be searched by means of sediment acoustics at least to the depth of a high‐velocity substratum of stronger reflection. 相似文献
18.
Seafloor mounds are potential geohazards to offshore rig emplacement and drilling operations and may contain evidence of underlying petroleum systems. Therefore, identifying and mapping them is crucial in de-risking exploration and production activities in offshore domains.A 738 km2 high resolution three-dimensional seismic dataset was used to investigate the occurrence, seismic characteristics and distribution of features interpreted as seafloor and buried sediment mounds, at water-depths of 800–1600 m, on the western Niger Delta slope. Fifteen seafloor mounds and eighteen shallowly buried mounds were identified. The seafloor mounds are characterised by lower seismic amplitude anomalies than the surrounding seabed sediments, and overlie vertical zones of acoustic blanking. The buried mounds in contrast are characterised by high amplitude anomalies; they also directly overlie sub-vertical zones of acoustic blanking. Seismic evidences from the features, their distribution patterns and tectono-stratigraphic associations suggest that their formation was controlled by the juxtaposition of buried channels and structural highs and their formation caused by focused fluid flow and expulsion of entrained sediments at the seabed.Considering the acoustic and geometrical characteristics of the mounds and comparing them with mound-shaped features from around the world, we conclude that the mounds most likely comprise heterolithic seafloor extrusions of muds and sands from the Agbada Formation with gas and possibly oil in some of the pore space giving rise to the acoustic characteristics. 相似文献
19.
Permeability–porosity relationships for sediments from the northern Barbados, Costa Rica, Nankai, and Peru subduction zones were examined based on sediment type, grain size distribution, and general mechanical and chemical compaction history. Greater correlation was observed between permeability and porosity in siliciclastic sediments, diatom oozes, and nannofossil chalks than in nannofossil oozes. For siliciclastic sediments, grouping of sediments by percentage of clay-sized material yields relationships that are generally consistent with results from other marine settings and suggests decreasing permeability as percentage of clay-sized material increases. Correction of measured porosities for smectite content improved the correlation of permeability–porosity relationships for siliciclastic sediments and diatom oozes. The relationship between permeability and porosity for diatom oozes is very similar to the relationship in siliciclastic sediments, and permeabilities of both sediment types are related to the amount of clay-size particles. In contrast, nannofossil oozes have higher permeability values by 1.5 orders of magnitude than siliciclastic sediments of the same porosity and show poor correlation between permeability and porosity. More indurated calcareous sediments, nannofossil chalks, overlap siliciclastic permeabilities at the lower end of their measured permeability range, suggesting similar consolidation patterns at depth. Thus, the lack of correlation between permeability and porosity for nannofossil oozes is likely related to variations in mechanical and chemical compaction at shallow depths. This study provides the foundation for a much-needed global database with fundamental properties that relate to permeability in marine settings. Further progress in delineating controls on permeability requires additional carefully documented permeability measurements on well-characterized samples. 相似文献
20.
在轴向应力-应变下海底沉积物声速及其变化 总被引：2，自引：0，他引：2
对南海南部海域海底浅表层沉积物短柱状样进行轴向应力-应变/声学测量,结果表明沉积物纵波声速有三种不同的变化结果:(1)声速从应变过程开始随应力-应变曲线变化,在最大应力时声速同时也是最大值,结束时可能高于或低于开始时的声速;(2)声速从应变过程开始逐渐减小,结束时是最小值;(3)声速从应变过程开始逐渐增大,最大值出现在结束时.这些结果与海底浅表层沉积物的物理力学性质、颗粒接触状态、颗粒的微结构等特征有关.研究结果可为深入认识南海南部各种海底沉积物作为承载界面的可靠性、声遥测遥感海底沉积物的工程力学性质等科学目的提供理论依据. 相似文献