首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献，搜索用时 46 毫秒
1.
Nearly half a century after mine closure, release of As from the Ylöjärvi Cu–W–As mine tailings in groundwater and surface water run-off was observed. Investigations by scanning electron microscopy (SEM), electron microprobe analysis (EMPA), synchrotron-based micro-X-ray diffraction (μ-XRD), micro-X-ray absorption near edge structure (μ-XANES) and micro-extended X-ray absorption fine structure (μ-EXAFS) spectroscopy, and a sequential extraction procedure were performed to assess As attenuation mechanisms in the vadose zone of this tailings deposit. Results of SEM, EMPA, and sequential extractions indicated that the precipitation of As bearing Fe(III) (oxy)hydroxides (up to 18.4 wt.% As2O5) and Fe(III) arsenates were important secondary controls on As mobility. The μ-XRD, μ-XANES and μ-EXAFS analyses suggested that these phases correspond to poorly crystalline and disordered As-bearing precipitates, including arsenical ferrihydrite, scorodite, kaňkite, and hydrous ferric arsenate (HFA). The pH within 200 cm of the tailings surface averaged 5.7, conditions which favor the precipitation of ferrihydrite. Poorly crystalline Fe(III) arsenates are potentially unstable over time, and their transformation to ferrihydrite, which contributes to As uptake, has potential to increase the As adsorption capacity of the tailings. Arsenic mobility in tailings pore water at the Ylöjärvi mine will depend on continued arsenopyrite oxidation, dissolution or transformation of secondary Fe(III) arsenates, and the As adsorption capacity of Fe(III) (oxy)hydroxides within this tailings deposit.  相似文献   

2.
  相似文献   

3.
《Applied Geochemistry》2005,20(3):639-659
The oxidation of sulfide minerals from mine wastes results in the release of oxidation products to groundwater and surface water. The abandoned high-sulfide Camp tailings impoundment at Sherridon, Manitoba, wherein the tailings have undergone oxidation for more than 70 a, was investigated by hydrogeological, geochemical, and mineralogical techniques. Mineralogical analysis indicates that the unoxidized tailings contain nearly equal proportions of pyrite and pyrrhotite, which make up to 60 wt% of the total tailings, and which are accompanied by minor amounts of chalcopyrite and sphalerite, and minute amounts of galena and arsenopyrite. Extensive oxidation in the upper 50 cm of the tailings has resulted in extremely high concentrations of dissolved SO4 and metals and As in the tailings pore water (pH < 1, 129,000 mg L−1 Fe, 280,000 mg L−1 SO4, 55,000 mg L−1 Zn, 7200 mg L−1 Al, 1600 mg L−1 Cu, 260 mg L−1 Mn, 110 mg L−1 Co, 97 mg L−1 Cd, 40 mg L−1 As, 15 mg L−1 Ni, 8 mg L−1 Pb, and 3 mg L−1 Cr). The acid released from sulfide oxidation has been extensive enough to deplete carbonate minerals to 6 m depth and to partly deplete Al-silicate minerals to a 1 m depth. Below 1 m, sulfide oxidation has resulted in the formation of a continuous hardpan layer that is >1 m thick. Geochemical modeling and mineralogical analysis indicate that the hardpan layer consists of secondary melanterite, rozenite, gypsum, jarosite, and goethite. The minerals indicated mainly control the dissolved concentrations of SO4, Fe, Ca and K. The highest concentrations of dissolved metals are observed directly above and within the massive hardpan layer. Near the water table at a depth of 4 m, most metals and SO4 sharply decline in concentration. Although dissolved concentrations of metals and SO4 decrease below the water table, these concentrations remain elevated throughout the tailings, with up to 60,600 mg L−1 Fe and 91,600 mg L−1 SO4 observed in the deeper groundwater. During precipitation events, surface seeps develop along the flanks of the impoundment and discharge pore water with a geochemical composition that is similar to the composition of water directly above the hardpan. These results suggest that shallow lateral flow of water from a transient perched water table is resulting in higher contaminant loadings than would be predicted if it were assumed that discharge is derived solely from the deeper primary water table. The abundance of residual sulfide minerals, the depletion of aluminosilicate minerals in the upper meter of the tailings and the presence of a significant mass of residual sulfide minerals in this zone after 70 a of oxidation suggest that sulfide oxidation will continue to release acid, metals, and SO4 to the environment for decades to centuries.  相似文献   

4.
Tailings generated during processing of sulfide ores represent a substantial risk to water resources. The oxidation of sulfide minerals within tailings deposits can generate low-quality water containing elevated concentrations of SO4, Fe, and associated metal(loid)s. Acid generated during the oxidation of pyrite [FeS2], pyrrhotite [Fe(1−x)S] and other sulfide minerals is neutralized to varying degrees by the dissolution of carbonate, (oxy)hydroxide, and silicate minerals. The extent of acid neutralization and, therefore, pore-water pH is a principal control on the mobility of sulfide-oxidation products within tailings deposits. Metals including Fe(III), Cu, Zn, and Ni often occur at high concentrations and exhibit greater mobility at low pH characteristic of acid mine drainage (AMD). In contrast, (hydr)oxyanion-forming elements including As, Sb, Se, and Mo commonly exhibit greater mobility at circumneutral pH associated with neutral mine drainage (NMD). These differences in mobility largely result from the pH-dependence of mineral precipitation–dissolution and sorption–desorption reactions. Cemented layers of secondary (oxy)hydroxide and (hydroxy)sulfate minerals, referred to as hardpans, may promote attenuation of sulfide-mineral oxidation products within and below the oxidation zone. Hardpans may also limit oxygen ingress and pore-water migration within sulfide tailings deposits. Reduction–oxidation (redox) processes are another important control on metal(loid) mobility within sulfide tailings deposits. Reductive dissolution or transformation of secondary (oxy)hydroxide phases can enhance Fe, Mn, and As mobility within sulfide tailings. Production of H2S via microbial sulfate reduction may promote attenuation of sulfide-oxidation products, including Fe, Zn, Ni, and Tl, via metal-sulfide precipitation. Understanding the dynamics of these interrelated geochemical and mineralogical processes is critical for anticipating and managing water quality associated with sulfide mine tailings.  相似文献   

5.
Published solubility data for amorphous ferric arsenate and scorodite have been reevaluated using the geochemical code PHREEQC with a modified thermodynamic database for the arsenic species. Solubility product calculations have emphasized measurements obtained under conditions of congruent dissolution of ferric arsenate (pH < 3), and have taken into account ion activity coefficients, and ferric hydroxide, ferric sulfate, and ferric arsenate complexes which have association constants of 104.04 (FeH2AsO42+), 109.86 (FeHAsO4+), and 1018.9 (FeAsO4). Derived solubility products of amorphous ferric arsenate and crystalline scorodite (as log Ksp) are −23.0 ± 0.3 and −25.83 ± 0.07, respectively, at 25 °C and 1 bar pressure. In an application of the solubility results, acid raffinate solutions (molar Fe/As = 3.6) from the JEB uranium mill at McClean Lake in northern Saskatchewan were neutralized with lime to pH 2-8. Poorly crystalline scorodite precipitated below pH 3, removing perhaps 98% of the As(V) from solution, with ferric oxyhydroxide (FO) phases precipitated starting between pH 2 and 3. Between pH 2.18 and 7.37, the apparent log Ksp of ferric arsenate decreased from −22.80 to −24.67, while that of FO (as Fe(OH)3) increased from −39.49 to −33.5. Adsorption of As(V) by FO can also explain the decrease in the small amounts of As(V)(aq) that remain in solution above pH 2-3. The same general As(V) behavior is observed in the pore waters of neutralized tailings buried for 5 yr at depths of up to 32 m in the JEB tailings management facility (TMF), where arsenic in the pore water decreases to 1-2 mg/L with increasing age and depth. In the TMF, average apparent log Ksp values for ferric arsenate and ferric hydroxide are −25.74 ± 0.88 and −37.03 ± 0.58, respectively. In the laboratory tests and in the TMF, the increasing crystallinity of scorodite and the amorphous character of the coexisting FO phase increases the stability field of scorodite relative to that of the FO to near-neutral pH values. The kinetic inability of amorphous FO to crystallize probably results from the presence of high concentrations of sulfate and arsenate.  相似文献   

6.
《Geochimica et cosmochimica acta》1999,63(19-20):3379-3394
The proposed JEB Tailings Management Facility (TMF) to be emplaced below the groundwater table in northern Saskatchewan, Canada, will contain uranium mill tailings from McClean Lake, Midwest and Cigar Lake ore bodies, which are high in arsenic (up to 10%) and nickel (up to 5%). A serious concern is the possibility that high arsenic and nickel concentrations may be released from the buried tailings, contaminating adjacent groundwaters and a nearby lake. Laboratory tests and geochemical modeling were performed to examine ways to reduce the arsenic and nickel concentrations in TMF porewaters so as to minimize such contamination from tailings buried for 50 years and longer. The tests were designed to mimic conditions in the mill neutralization circuit (3 hr tests at 25°C), and in the TMF after burial (5–49 day aging tests). The aging tests were run at, 50, 25 and 4°C (the temperature in the TMF). In order to optimize the removal of arsenic by adsorption and precipitation, ferric sulfate was added to tailings raffinates1 having Fe/As ratios of less that 3–5. The acid raffinates were then neutralized by addition of slaked lime to nominal pH values of 7, 8, or 9.Analysis and modeling of the test results showed that with slaked lime addition to acid tailings raffinates, relatively amorphous scorodite (ferric arsenate) precipitates near pH 1, and is the dominant form of arsenate in slake limed tailings solids except those high in Ni and As and low in Fe, in which cabrerite-annabergite (Ni, Mg, Fe(II) arsenate) may also precipitate near pH 5–6. In addition to the arsenate precipitates, smaller amounts of arsenate are also adsorbed onto tailings solids.The aging tests showed that after burial of the tailings, arsenic concentrations may increase with time from the breakdown of the arsenate phases (chiefly scorodite). However, the tests indicate that the rate of change decreases and approaches zero after 72 hrs at 25°C, and may equal zero at all times in the TMF at 4°C. Consistent with a kinetic model that describes the rate of breakdown of scorodite to form hydrous ferric oxide, the rate of release of dissolved arsenate to tailings porewaters from slake limed tailings: (1) is proportional to pH above pH 6–7; (2) decreases exponentially as the total molar Fe/As ratio of tailings raffinates is increased from 1/1 to greater than 5/1; and (3) is proportional to temperature with an average Arrhenius activation energy of 13.4 ± 4.2 kcal/mol.Study results suggest that if ferric sulfate and slaked lime are added in the tailings neutralization circuit to give a raffinate Fe/As molar ratio of at least 3–5 and a nominal (initial) pH of 8 (final pH of 7–8), arsenic and nickel concentrations of 2 mg/L or less, are probable in porewaters of individual tailings in the TMF for 50 to 10,000 yrs after tailings disposal. However, the tailings will be mixed in the TMF, which will contain about 35% tailings with Fe/As = 3.0, and 65% tailings with Fe/As = 5.0–7.7. Thus, it seems likely that average arsenic pore water concentrations in the TMF may not exceed 1 mg/L.  相似文献   

7.
Historical gold mining operations in Nova Scotia, Canada, resulted in numerous deposits of publicly accessible, arsenic (As)-rich mine waste that has weathered in situ for 75–150 years, resulting in a wide range of As-bearing secondary minerals. The geochemical heterogeneity of this mine waste creates a challenge for identifying a single remediation approach that will limit As mobility. A 30-cm-thick, low-organic content soil cover was evaluated in a laboratory leaching experiment where, to simulate natural conditions, the equivalent of 2 years of synthetic rainwater was leached through each column and two dry seasons were incorporated into the leaching protocol. Each column was a stratigraphic representation of the four major tailings types found at the historical Montague and Goldenville gold mine districts: hardpan tailings, oxic tailings, wetland tailings, and high Ca tailings. Hardpan tailings released acidic, As-rich waters (max 12 mg/L) under the soil cover but this acidity was buffered by surrounding oxic tailings. Leachate from the oxic tailings was circumneutral, with average As concentrations between 4.4 and 9.7 mg/L throughout the experiment. The presence of carbonates in the high Ca tailings resulted in near-neutral to weakly alkaline leachate pH values and average As concentrations between 2.1 and 6.1 mg/L. Oxidation of sulfides in the wetland tailings led to acidic leachate over time and a decrease in As concentrations to values that were generally less than 1 mg/L. This study shows that the use of a low-organic content soil cover does not create reducing conditions that would destabilize oxidized, As-bearing secondary phases in these tailings. However, oxygen penetration through the cover during dry seasons would continue to release As to tailings pore waters via sulfide oxidation reactions.  相似文献   

8.
Processing of arsenopyrite ore took place at Blackwater Au mine, New Zealand, between 1908 and 1951 and no rehabilitation was undertaken after mine closure. High As concentrations in solid processing residues (up to 40 wt% As) are due to secondary As minerals. Site pH regimes vary from 4.1 to circum-neutral. Originally, all processed As was present as arsenolite (arsenic trioxide polymorph, AsIII), a by-product of arsenopyrite roasting. Near the roaster, scorodite precipitated as a result of the high dissolved As concentration during arsenolite dissolution. The formation of scorodite has two major consequences. Firstly, the scorodite precipitate cements the ground in the vicinity of the roaster area, thereby creating an impermeable surface crust (up to 30 wt% As) and encapsulating weathered arsenolite grains within the cement. Secondly, formation of scorodite temporarily immobilizes some of the dissolved As that is generated during nearby arsenolite dissolution. Where all the available arsenolite has dissolved, scorodite becomes soluble, and the dissolved As concentrations are controlled by scorodite solubility, which is at least two orders of magnitudes lower than arsenolite solubility. Downstream Eh conditions fall below the AsV/AsIII boundary, so that scorodite does not precipitate and dissolved As concentrations are controlled by arsenolite solubility. Dissolved As reaches up to 52 mg/L in places, and exceeds the current WHO drinking water guideline of 0.01 mg/L by 5200 times. This study shows that dissolved As concentrations in discharge waters at historic mine sites are dependent on the processing technology and associated mineralogy.  相似文献   

9.
Scorodite, ferric arsenate and arsenical ferrihydrite are important arsenic carriers occurring in a wide range of environments and are also common precipitates used by metallurgical industries to control arsenic in effluents. Solubility and stability of these compounds are controversial because of the complexities in their identification and characterization in heterogeneous media. To provide insights into the formation of scorodite, ferric arsenate and ferrihydrite, series of synthesis experiments were carried out at 70 °C and pH 1, 2, 3 and 4.5 from 0.2 M Fe(SO4)1.5 solutions also containing 0.02-0.2 M Na2HAsO4. The precipitates were characterized by transmission electron microscopy, X-ray diffraction and X-ray absorption fine structure techniques. Ferric arsenate, characterized by two broad diffuse peaks on the XRD pattern and having the structural formula of FeAsO4·4-7H2O, is a precursor to scorodite formation. As defined by As XAFS and Fe XAFS, the local structure of ferric arsenate is profoundly different than that of scorodite. It is postulated that the ferric arsenate structure is made of single chains of corner-sharing Fe(O,OH)6 octahedra with bridging arsenate tetrahedra alternating along the chains. Scorodite was precipitated from solutions with Fe/As molar ratios of 1 over the pH range of 1-4.5. The pH strongly controls the kinetics of scorodite formation and its transformation from ferric arsenate. The scorodite crystallite size increased from 7 to 33 nm by ripening and aggregation. Precipitates, resulting from continuous synthesis at pH 4.5 from solutions having Fe/As molar ratios ranging from 1 to 4 and resembling the compounds referred to as ferric arsenate, arsenical ferrihydrite and As-rich hydrous ferric oxide in the literature, represent variable mixtures of ferric arsenate and ferrihydrite. When the Fe/As ratio increases, the proportion of ferrihydrite increases at the expense of ferric arsenate. Arsenate adsorption appears to retard ferrihydrite growth in the precipitates with molar Fe/As ratios of 1-4, whereas increased reaction gradually transforms two-line ferrihydrite to six-line ferrihydrite at Fe/As ratios of 5 and greater.  相似文献   

10.
In northern Saskatchewan, Canada, high-grade U ores and the resulting tailings can contain high levels of As. An environmental concern in the U mining industry is the long-term stability of As within tailings management facilities (TMFs) and its potential transfer to the surrounding groundwater. To mitigate this problem, U mill effluents are neutralized with lime to reduce the aqueous concentration of As. This results in the formation of predominantly Fe3+–As5+ secondary mineral phases, which act as solubility controls on the As in the tailings discharged to the TMF. Because the speciation of As in natural systems is critical for determining its long-term environmental fate, characterization of As-bearing mineral phases and complexes within the deposited tailings is required to evaluate its potential transformation, solubility, and long-term stability within the tailings mass. In this study, synchrotron-based bulk X-ray absorption spectroscopy (XAS) was used to study the speciation of As and Fe in mine tailings samples obtained from the Deilmann TMF at Key Lake, Saskatchewan. Comparisons of K-edge X-ray absorption spectra of tailings samples and reference compounds indicate the dominant oxidation states of As and Fe in the mine tailings samples are +5 and +3, respectively, largely reflecting their generation in a highly oxic mill process, deposition in an oxidized environment, and complexation within stable oxic phases. Linear combination fit analyses of the K-edges for the Fe X-ray absorption near edge spectra (XANES) to reference compounds suggest Fe is predominantly present as ferrihydrite with some amount of the primary minerals pyrite (8–15% in some samples) and chalcopyrite (5–15% in some samples). Extended X-ray absorption fine structure (EXAFS) analysis of As K-edge spectra indicates that As5+ (arsenate) present in tailings samples is adsorbed to the ferrihydrite though an inner-sphere bidentate linkage.  相似文献   

11.
《Applied Geochemistry》2005,20(5):947-959
At the McClean Lake Operation in the Athabasca Basin of northern Saskatchewan, the untreated acid raffinate solutions associated with U mill tailings contain up to 700 mg/L dissolved As. To reduce the concentration of As and other contaminants in acid tailing slurries at the JEB mill at McClean Lake, ferric sulfate may be added to the acid raffinates to assure that their molar Fe/As ratio equals or exceeds 3. Tailings slurries are then neutralized with lime to pH 4, and subsequently to pH 7–8. The neutralized tailings contain minerals from the original ore, which are chiefly quartz, illite, kaolinite and chlorite, and precipitated (secondary) minerals that include gypsum, scorodite, annabergite, hydrobasaluminite and ferrihydrite. Most of the As is associated with the secondary arsenate minerals, scorodite and annabergite. However, a few percent is adsorbed and/or co-precipitated, mainly by ferrihydrite. Of major concern to provincial and federal regulators is the risk that significant amounts of As might be released from the tailings to pore waters after their subaqueous disposal in the tailings management facility. A laboratory study was performed to address this issue, measuring readily desorbed As using a method known as equilibrium partitioning in closed systems (EPICS). The EPICS method was selected because it employs a leaching solution that, except for its As concentration, is identical in composition to the neutralized raffinate in contact with the tailings. Laboratory experiments and modeling results demonstrated that the As that could be readily released to pore waters is about 0.2% of the total As in the tailings. Long-term, such releases may contribute no more than a few mg/L of dissolved As to tailings pore waters.  相似文献   

12.
Arsenite sorption on troilite (FeS) and pyrite (FeS2)   总被引：4，自引：0，他引：4  
Arsenic is a toxic metalloid whose mobility and availability are largely controlled by sorption on sulfide minerals in anoxic environments. Accordingly, we investigated reactions of As(III) with iron sulfide (FeS) and pyrite (FeS2) as a function of total arsenic concentration, suspension density, sulfide concentration, pH, and ionic strength. Arsenite partitioned strongly on both FeS and FeS2 under a range of conditions and conformed to a Langmuir isotherm at low surface coverages; a calculated site density of near 2.6 and 3.7 sites/nm2 for FeS and FeS2, respectively, was obtained. Arsenite sorbed most strongly at elevated pH (>5 to 6). Although solution data suggested the formation of surface precipitates only at elevated solution concentrations, surface precipitates were identified using X-ray absorption spectroscopy (XAS) at all coverages. Sorbed As was coordinated to both sulfur [d(As-S) = 2.35 Å] and iron [d(As-Fe) = 2.40 Å], characteristic of As coordination in arsenopyrite (FeAsS). The absorption edge of sorbed As was also shifted relative to arsenite and orpiment (As2S3), revealing As(III) reduction and a complete change in As local structure. Arsenic reduction was accompanied by oxidation of both surface S and Fe(II); the FeAsS-like surface precipitate was also susceptible to oxidation, possibly influencing the stability of As sorbed to sulfide minerals in the environment. Sulfide additions inhibit sorption despite the formation of a sulfide phase, suggesting that precipitation of arsenic sulfide is not occurring. Surface precipitation of As on FeS and FeS2 supports the observed correlation of arsenic and pyrite and other iron sulfides in anoxic sediments.  相似文献   

13.
《Applied Geochemistry》2006,21(8):1259-1273
Grains of naturally oxidized arsenopyrite [FeAsS] collected from the oxidation zone in W-mine tailings were investigated, primarily using transmission electron microscopy. The grains are severely pitted and are surrounded by secondary minerals. The pitted nature of the grains is related to mechanisms governing the electrochemical oxidation of sulfide minerals, with prominent cusp-like features occurring at cathodic regions of the surface, and pits occurring at anodic regions. In general, the oxidation of arsenopyrite leads to the formation of an amorphous (or nanocrystalline) Fe–As–O-rich coating that contains small amounts of Si, Ca, Cu, Zn, Pb and Bi; nanoscale variation in the As, Pb, Bi and Zn contents of the coating was noted. Secondary Cu sulfides, thought to be chalcocite [Cu2S] and (or) djurleite [Cu31S16], occur as a layer (generally <500 nm thick) along the arsenopyrite grain boundary, and also within the coating as aggregates, and as layers that parallel the grain boundary. Although the precipitation of secondary Cu minerals along the grain boundary is a nanoscale feature, the process of formation is thought to be analogous to the supergene enrichment that occurs in weathered sulfide deposits. As the oxidation of arsenopyrite proceeds, layers and clusters of secondary Cu sulfides become isolated in the Fe–As–O coating. Secondary wulfenite [PbMoO4] and an unidentified crystalline Bi–Pb–As–O mineral occur in voids within the coating, suggesting that these minerals precipitated from the local pore-water. Small and variable amounts of W, Ca, Bi, As and Zn are associated with the wulfenite, and Zn, Fe and Ca are associated with the Bi–Pb–As–O mineral. Some of the wulfenite is in contact with inclusions of molybdenite [MoS2], suggesting that the oxidation of molybdenite in the presence of aqueous Pb(II) led to the formation of wulfenite. Mineralogical analyses at the nanoscale have improved the understanding of geochemical sources and sinks at this location. The results of this study indicate that the mineralogical controls on aqueous elemental concentrations at this tailings site are complex and are not predicted by thermodynamic calculations.  相似文献   

14.
Speciation and colloid transport of arsenic from mine tailings   总被引：2，自引：0，他引：2  
In addition to affecting biogeochemical transformations, the speciation of As also influences its transport from tailings at inoperative mines. The speciation of As in tailings from the Sulfur Bank Mercury Mine site in Clear Lake, California (USA) (a hot-spring Hg deposit) and particles mobilized from these tailings have been examined during laboratory-column experiments. Solutions containing two common, plant-derived organic acids (oxalic and citric acid) were pumped at 13 pore volumes d−1 through 25 by 500 mm columns of calcined Hg ore, analogous to the pedogenesis of tailings. Chemical analysis of column effluent indicated that all of the As mobilized was particulate (1.5 mg, or 6% of the total As in the column through 255 pore volumes of leaching). Arsenic speciation was evaluated using X-ray absorption spectroscopy (XAS), indicating the dominance of arsenate [As(V)] sorbed to poorly crystalline Fe(III)-(hydr)oxides and coprecipitated with jarosite [KFe3(SO4, AsO4)2(OH)6] with no detectable primary or secondary minerals in the tailings and mobilized particles. Sequential chemical extractions (SCE) of <45 μm mine tailings fractions also suggest that As occurs adsorbed to Fe (hydr)oxides (35%) and coprecipitated within poorly crystalline phases (45%). In addition, SCEs suggest that As is associated with 1 N acid-soluble phases such as carbonate minerals (20%) and within crystalline Fe-(hydr)oxides (10%). The finding that As is transported from these mine tailings dominantly as As(V) adsorbed to Fe (hydr)oxides or coprecipitated within hydroxysulfates such as jarosite suggests that As release from soils and sediments contaminated with tailings will be controlled by either organic acid-promoted dissolution or reductive dissolution of host phases.  相似文献   

15.
Column leaching experiments were used to determine the effects of an iron-rich hardpan layer, on the rate of tailings oxidation and the composition of leachate waters, from the Renison Bell tailings dams in western Tasmania, Australia. One-meter-long PVC columns, filled with tailings, cover material (Cassiterite Flotation Tailings) and hardpan samples from the tailings dams, were leached over a period of 14 weeks. Under dry cover conditions, when hardpan was present, the solute loads peaked at 21–49 days (Fe at 2,294 ppm and SO 4 2- at 4,700 ppm), and stabilised at much lower concentrations after 9 weeks. In contrast, the solute loads steadily increased over time in the column where hardpan was absent (SO 4 2- from 1,800 to 3,100 ppm, and Fe from 407 to 1,692 ppm). Under saturated cover conditions, the solute concentrations in the leachate also increased with time (SO 4 2-from 1,900 to 17,000 ppm, and Fe from 480 to 8,500 ppm). The presence of a hardpan layer between the reactive tailings and cover material has been found to improve leachate water chemistry and lessen the rate of sulphide oxidation.  相似文献   

16.
 The oxidation and the subsequent dissolution of sulfide minerals within the Copper Cliff tailings area have led to the release of heavy metals such as Fe, Ni, and Co to the tailings pore water. Dissolved concentrations in excess of 10 g/l Fe and 2.2 g/l Ni have been detected within the shallow pore water of the tailings, with increasing depth these concentrations decrease to or near analytical detection limits. Geochemical modelling of the pore-water chemistry suggests that pH-buffering reactions are occurring within the shallow oxidized zones, and that secondary phases are precipitating at or near the underlying hardpan and transition zones. Mineralogical study of the tailings confirmed the presence of goethite, jarosite, gypsum, native sulfur, and a vermiculite-type clay mineral. Goethite, jarosite, and native sulfur form alteration rims and pseudo-morphs of the sulfide minerals. Interstitial cements, composed of goethite, jarosite, and gypsum, locally bind the tailings particles, forming hardpan layers. Microprobe analyses of the goethite indicate that it contains up to 0.6 weight % Ni, suggesting that the goethite is a repository for Ni. Other sinks detected for heavy metals include jarosite and a vemiculite-type clay mineral which locally contains up to 1.6 weight % Ni. To estimate the mass and distribution of heavy metals associated with the secondary phases within the shallow tailings, a series of chemical extractions was completed. The experimental design permitted four fractions of the tailings to be evaluated independently. These four fractions consisted of a water-soluble, an acid-leachable, and a reducible fraction, as well as the whole-rock total. Twenty-five percent of the total mass of heavy metals was removed in the acid-leaching experiments, and 100% of the same components were removed in the reduction experiments. The data suggest that precipitation/coprecipitation reactions are providing an effective sink for most of the heavy metals released by sulfide mineral oxidation. In light of these results, potential decommissioning strategies should be evaluated with the recognition that changing the geochemical conditions may alter the stability of the secondary phases within the shallow tailings. Received: 9 April 1997 · Accepted: 21 July 1997  相似文献   

17.
Solubility experiments were performed on nanocrystalline scorodite and amorphous ferric arsenate. Nanocrystalline scorodite occurs as stubby prismatic crystals measuring about 50 nm and having a specific surface area of 39.88 ± 0.07 m2/g whereas ferric arsenate is amorphous and occurs as aggregated clusters measuring about 50–100 nm with a specific surface area of 17.95 ± 0.19 m2/g. Similar to its crystalline counterpart, nanocrystalline scorodite has a solubility of about 0.25 mg/L at around pH 3–4 but has increased solubilities at low and high pH (i.e. <2 and >6). Nanocrystalline scorodite dissolves incongruently at about pH > 2.5 whereas ferric arsenate dissolution is incongruent at all the pH ranges tested (pH 2–5). It appears that the solubility of scorodite is not influenced by particle size. The dissolution rate of nanocrystalline scorodite is 2.64 × 10−10 mol m−2 s−1 at pH 1 and 3.25 × 10−11 mol m−2 s−1 at pH 2. These rates are 3–4 orders of magnitude slower than the oxidative dissolution of pyrite and 5 orders of magnitude slower than that of arsenopyrite. Ferric arsenate dissolution rates range from 6.14 × 10−9 mol m−2 s−1 at pH 2 to 1.66 × 10−9 mol m−2 s−1 at pH 5. Among the common As minerals, scorodite has the lowest solubility and dissolution rate. Whereas ferric arsenate is not a suitable compound for As control in mine effluents, nanocrystalline scorodite that can be easily precipitated at ambient pressure and temperature conditions would be satisfactory in meeting the regulatory guidelines at pH 3–4.  相似文献   

18.
Acid mine drainage (AMD) is a common pollution in mining areas due to the oxidation of pyrite and associated sulfide minerals at mines, tailings and mine dumps. Elevated metals (Fe, Mn, Al) and metalloids (As, Hg) in AMD would deteriorate the local aquatic environment and influence the water supply. A carbonate basin with deposits of high-arsenic coal in Xingren County, southwestern China, was chosen to study the behavior of As and other chemical constituents along a river receiving AMD. Heavy metals (Fe, Mn) and major ions such as (Ca2+, Mg2+, Cl−, SO4 2−) in surface water, and As in sediment and surface water were analyzed. It was found that high concentrations of SO4 2− (1,324–7,560 mg/L) and Fe (369–1,472 mg/L) in surface water were mainly controlled by the interactions between water and rocks such as the oxidation of pyrite in the local coal seams, precipitation and adsorption of iron minerals. Although ubiquitous carbonate minerals in the bedrock and the riverbeds, low pH (<3) water was maintained until 2 km downstream from the AMD source due to the Fe(hydro)oxide minerals coating on the surface of carbonate minerals to restrain the neutralization of acidic water. Moreover, the formation of Fe(hydro)oxide precipitations absorbed As was dominated the attenuation of As from water to sediment. Whereas, the dilution also played an important role in decrease of As in river water.  相似文献   

19.
《Applied Geochemistry》2003,18(11):1733-1750
The Rabbit Lake U mine in-pit tailings management facility (TMF) (425 m long×300 m wide×91 m deep) is located in northern Saskatchewan, Canada. The objectives of this study were to quantify the distribution of As phases in the tailings and evaluate the present-day geochemical controls on dissolved As. These objectives were met by analyzing pore fluid samples collected from the tailings body for dissolved constituents, measuring Eh, pH, and temperature of tailings core and pore fluid samples, conducting sequential extractions on solid samples, conducting geochemical modeling of pore fluid chemistry using available thermodynamic data, and by reviewing historical chemical mill process records. Dissolved As concentrations in 5 monitoring wells installed within the tailings body ranged from 9.6 to 71 mg/l. Pore fluid in the wells had a pH between 9.3 and 10.3 and Eh between +58 and +213 mV. Sequential extraction analyses of tailings samples showed that the composition of the solid phase As changed at a depth of 34 m. The As above 34 m was primarily associated with amorphous Fe and metal hydroxides while the As below 34 m was associated with Ca, likely as amorphous poorly ordered calcium arsenate precipitates. The change in the dominant As solid phases at this depth was attributed to the differences in the molar ratio of Fe to As in the mill tailings. Below 34 m it was <2 whereas above 34 m it was >4. The high Ca/As ratio during tailings neutralization would likely precipitate Ca4(OH)2(AsO4)2:4H2O type Ca arsenate minerals. Geochemical modeling suggested that if the pore fluids were brought to equilibrium with this Ca-arsenate, the long-term dissolved As concentrations would range between 13 and 126 mg/l.  相似文献   

20.
Mine tailings at the former Delnite gold mine in northern Ontario were characterized to assess the impact of a biosolids cover on the stability of As species and evaluate options for long-term management of the tailings. Arsenic concentrations in the tailings range from 0.15 to 0.36 wt% distributed among goethite, pyrite and arsenopyrite. Pyrite and arsenopyrite occur as small and liberated particles that are enveloped by goethite in the uncovered tailings and the deeper portions of the biosolids-covered tailings. Sulfide particles in the shallower portions of the biosolids-covered tailings are free of goethite rims. Arsenic occurs predominantly as As5+ with minor amount of As1− in the uncovered tailings. Coinciding with the disappearence of goethite rims on sulfide particles, the biosolids-covered tailings have As3+ species gradually increasing in proportion towards the cover. Leaching tests indicated that the As concentrations in the leachate gradually increase from less than 0.085 to 13 mg/L and Fe from 28 to 179 mg/L towards the biosolids cover. These are in sheer contrast to the leachate concentrations of less than 0.085 mg/L As and 24–64 mg/L Fe obtained from the uncovered tailings confirming the role of biosolids-influenced reduction and mobilization of As in the form of As3+ species. The evidence suggests that reductive dissolution of goethite influenced by the biosolids-cover caused the mobilization of As as As3+ species.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号