首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献，搜索用时 31 毫秒
1.
Identification of debris‐flow hazard areas necessitates the knowledge of the flow thickness and the runout distance. Both have been investigated using a numerical runout model. On the Faucon stream (South French Alps), representative of clay‐shale basins, results of various rheological tests and numerical experiments are presented and discussed. The calibration of the model was undertaken using the results of both geomorphological surveys and sedimentological analyses. Rheological tests using either a parallel‐plate rheometer, a coaxial rheometer, slump tests, and an inclined plane were carried out on several samples. Results have shown that the flow behaviour could be described by an Herschel‐Bulkley constitutive equation. The rheological responses of several natural suspensions collected from surficial deposits (sandstones, moraines, weathered black marls) were also investigated. In order to model the runout of the flow, the model BING was used. The model describes well the influence of each type of sediment on the behaviour (runout distance, deposit thickness) of the flow, although the velocities were significantly overestimated. Different risk scenarios are tested and discussed. Copyright © 2005 John Wiley & Sons, Ltd.  相似文献   

2.
  相似文献   

3.
Debris flows can grow greatly in size by entrainment of bed material, enhancing their runout and hazardous impact. Here, we experimentally investigate the effects of debris‐flow composition on the amount and spatial patterns of bed scour and erosion downstream of a fixed to erodible bed transition. The experimental debris flows were observed to entrain bed particles both grain by grain and en masse, and the majority of entrainment was observed to occur during passage of the flow front. The spatial bed scour patterns are highly variable, but large‐scale patterns are largely similar over 22.5–35° channel slopes for debris flows of similar composition. Scour depth is generally largest slightly downstream of the fixed to erodible bed transition, except for clay‐rich debris flows, which cause a relatively uniform scour pattern. The spatial variability in the scour depth decreases with increasing water, gravel (= grain size) and clay fraction. Basal scour depth increases with channel slope, flow velocity, flow depth, discharge and shear stress in our experiments, whereas there is no correlation with grain collisional stress. The strongest correlation is between basal scour and shear stress and discharge. There are substantial differences in the scour caused by different types of debris flows. In general, mean and maximum scour depths become larger with increasing water fraction and grain size, and decrease with increasing clay content. However, the erodibility of coarse‐grained experimental debris flows (gravel fraction = 0.64) is similar on a wide range of channel slopes, flow depths, flow velocities, discharges and shear stresses. This probably relates to the relatively large influence of grain‐collisional stress to the total bed stress in these flows (30–50%). The relative effect of grain‐collisional stress is low in the other experimental debris flows (<5%), causing erosion to be largely controlled by basal shear stress. Copyright © 2016 John Wiley & Sons, Ltd.  相似文献   

4.
The rheology of debris flows is difficult to characterize owing to the varied composition and to the uneven distribution of the components that may range from clay to large boulders, in addition to water. Few studies have addressed debris flow rheology from observational, experimental, and theoretical viewpoints in conjunction. We present a coupled rheological‐numerical model to characterize the debris flows in which cohesive and frictional materials are both present. As a first step, we consider small‐scale artificial debris flows in a flume with variable percentages of clay versus sand, and measure separately the rheological properties of sand–clay mixtures. A comparison with the predictions of a modified version of the numerical model BING shows a reasonable agreement between measurements and simulations. As application to a field case, we analyse a recent debris flow that occurred in Fjærland (Western Norway) for which much information is now available. The event was caused by a glacial lake outburst flood (GLOF) originating from the failure of a moraine ridge. In a previous contribution (Breien et al., Landslides, 2008 , 5: 271–280) we focused on the hydrological and geomorphological aspects. In particular we documented the marked erosion and reported the change in sediment transport during the event. In contrast to the laboratory debris flows, the presence of large boulders and the higher normal pressure inside the natural debris flow requires the introduction of a novel rheological model that distinguishes between mud‐to–clast supported material. We present simulations with a modified BING model with the new cohesive‐frictional rheology. To account for the severe erosion operated by the debris flow on the colluvial deposits of Fjærland, we also suggest a simple model for erosion and bulking along the slope path. Numerical simulations suggest that a self‐sustaining mechanism could partly explain the extreme growth of debris flows running on a soft terrain.  相似文献   

5.
A new method to predict the runout of debris flows is presented. A data base of documented sediment‐transporting events in torrent catchments of Austria, Switzerland and northern Italy has been compiled, using common classification techniques. With this data we test an empirical approach between planimetric deposition area and event volume, and compare it with results from other studies. We introduce a new empirical relation to determine the mobility coefficient as a function of geomorphologic catchment parameters. The mobility coefficient is thought to reflect some of the flow properties during the depositional part of the debris‐flow event. The empirical equations are implemented in a geographical information system (GIS) based simulation program and combined with a simple flow routing algorithm, to determine the potential runout area covered by debris‐flow deposits. For a given volume and starting point of the deposits, a Monte‐Carlo technique is used to produce flow paths that simulate the spreading effect of a debris flow. The runout zone is delineated by confining the simulated potential spreading area in the down slope direction with the empirically determined planimetric deposition area. The debris‐flow volume is then distributed over the predicted area according to the calculated outflow probability of each cell. The simulation uses the ARC‐Objects environment of ESRI© and is adapted to run with high resolution (2·5 m × 2·5 m) digital elevation models, generated for example from LiDAR data. The simulation program called TopRunDF is tested with debris‐flow events of 1987 and 2005 in Switzerland. Copyright © 2009 John Wiley & Sons, Ltd.  相似文献   

6.
In Carrara marble basins, the long and intensive quarrying activities (which began in the first century BC ) have produced extensive dump deposits, locally known as ravaneti. Ravaneti are of such large dimensions and diffusion as to make them a widespread landform of the Apuane Alps (Tuscany). In recent years these quarry dump deposits have been affected by frequent debris flows, more than 50 in 1996/97. This phenomenon is the most significant currently active geomorphological process in this landscape. The evolution of quarrying techniques produced a variety of sedimentological compositions of ravaneti. The debris flows analysed involve only the surface layers where debris is mixed with fine material with a lower permeability (active ravaneti) than the coarser underlying debris (older ravaneti). The presence of different permeability layers causes a wetting front to move downwards. Source area observations indicate a soil slip movement in the initial phases of the failure. The transformation of landslides into debris flow occurs by means of both soil contractive failure and an increase of granular temperature. The morphological and sedimentological analyses of depositional lobes resulted in a classification of three types of lobe, based on fabric–morphometry relationships allowing the identification of different flow dynamics: (1) type A lobe (platy form), matrix‐supported and well developed fabric with general tendency of ab clast plane strikes to lie generally parallel to flow direction as a consequence of laminar flow; (2) type B lobe (elongated form), clast‐supported and random fabric as a consequence of both turbulent flow and coarser composition of starting material; (3) type C lobe, intermediate type A–B morphometry, tendency for ab clast plane to lie in a semi‐circle around the main flow direction determined by the presence of secondary flow lines divergent from it in the stopping phase. In Carrara marble basins, the anomalous frequency with which debris flows tend to be triggered by medium‐intensity rainstorms (about 30 mm h−1 rainfall) is due to the recent increases in silt dump produced by modern quarrying techniques. This represents a significant example of debris flows as an environmental problem in major anthromorphized landscapes. Copyright © 2000 John Wiley & Sons, Ltd.  相似文献   

7.
The geomorphological characteristics of small debris flows in a maritime sub‐Antarctic environment are described. The morphological and sedimentological characteristics of the debris flows are comparable to debris flows documented for other parts of the world; their initiation appears closely linked to the unusual environment in which they are found. Sediment supply is generated by diurnal frost heave of loamy sediment associated with Azorella selago. The debris flows are triggered by sediment mobilization upon saturation of the frost‐heaved surface gravel and overland flow over the low‐permeability and frost‐susceptible slope materials. Morphological effects of the flows are short‐lived due to obliteration by subsequent frost heave activity. Copyright © 2000 John Wiley & Sons, Ltd.  相似文献   

8.
Due to their potentially long runout, debris flows are a major hazard and an important geomorphic process in mountainous environments. Understanding runout is therefore essential to minimize risk in the near-term and interpret the pace and pattern of debris flow erosion and deposition over geomorphic timescales. Many debris flows occur in forested landscapes where they mobilize large volumes of large woody debris (LWD) in addition to sediment, but few studies have quantitatively documented the effects of LWD on runout. Here, we analyze recent and historic debris flows in southeast Alaska, a mountainous, forested system with minimal human alteration. Sixteen debris flows near Sitka triggered on August 18, 2015 or more recently had volumes of 80 to 25 000 m3 and limited mobility compared to a global compilation of similarly-sized debris flows. Their deposits inundated 31% of the planimetric area, and their runout lengths were 48% of that predicted by the global dataset. Depositional slopes were 6°–26°, and mobility index, defined as the ratio of horizontal runout to vertical elevation change, ranged from 1.2 to 3, further indicating low mobility. In the broader southeast Alaskan region consisting of Chichagof and Baranof Islands, remote sensing-based analysis of 1061 historic debris flows showed that mobility index decreased from 2.3–2.5 to 1.4–1.8 as average forest age increased from 0 to 416 years. We therefore interpret that the presence of LWD within a debris flow and standing trees, stumps, and logs in the deposition zone inhibit runout, primarily through granular phenomena such as jamming due to force chains. Calibration of debris flow runout models should therefore incorporate the ecologic as well as geologic setting, and feedbacks between debris flows and vegetation likely control the transport of sediment and organic material through steep, forested catchments over geomorphic time. © 2020 John Wiley & Sons, Ltd.  相似文献   

9.
The central focus of this work is to study the processes acting well below the surface of a moving rock or debris avalanche during travel over stationary substrate material. Small‐scale physical models at a linear scale of 1:104 used coal as avalanche analogue material and different granular material simulating sedimentary substrates varying in frictional resistance, thickness and relative basal boundary roughness, as well as inerodible, non‐deformable runout path conditions. Substrate materials with the least frictional resistance showed the greatest response to granular flow overriding, becoming entirely mobilized beneath and ahead of the moving mass and producing the longest runout observed with a unique deposit profile shape. With a smooth substrate basal contact, failure occurred along this plane and avalanche and substrate became coupled during runout. With a rough base, however, temporary force chains of grain contacts in the substrate prevailed longer, imparted their resistance to motion/shear into the granular flow, and the flow rear section consequently halted earlier than when moving over substrates with a weak base. Reducing substrate thickness diminished the effect of basal contact roughness on granular flow runout and deposit length. Inerodible, non‐deformable substrate conditions caused changes in granular flow behaviour from essentially en masse sliding on low‐friction surfaces to increasing granular agitation over rougher paths. Copyright © 2012 John Wiley & Sons, Ltd.  相似文献   

10.
Volcanoes of the Trans-Mexican Volcanic Belt (TMVB) have yielded numerous sector and flank collapses during Pleistocene and Holocene times. Sector collapses associated with magmatic activity have yielded debris avalanches with generally limited runout extent (e.g. Popocatépetl, Jocotitlán, and Colima volcanoes). In contrast, flank collapses (smaller failures not involving the volcano summit), both associated and unassociated with magmatic activity and correlating with intense hydrothermal alteration in ice-capped volcanoes, commonly have yielded highly mobile cohesive debris flows (e.g. Pico de Orizaba and Nevado de Toluca volcanoes). Collapse orientation in the TMVB is preferentially to the south and northeast, probably reflecting the tectonic regime of active E–W and NNW faults. The differing mobilities of the flows transformed from collapses have important implications for hazard assessment. Both sector and flank collapse can yield highly mobile debris flows, but this transformation is more common in the cases of the smaller failures. High mobility is related to factors such as water content and clay content of the failed material, the paleotopography, and the extent of entrainment of sediment during flow (bulking). The ratio of fall height to runout distance commonly used for hazard zonation of debris avalanches is not valid for debris flows, which are more effectively modeled with the relation inundated area to failure or flow volume coupled with the topography of the inundated area.  相似文献   

11.
Predicting the spatial impact of debris flows on fans is challenging due to complex runout behaviour. Debris flow mobility is highly variable and flows can sporadically avulse the channel. For hazard and risk assessments, practitioners typically base the probability of spatial impact or avulsion on their experience and expert judgement. To support decision-making with empirical observations, we studied spatial impact distributions on 30 active debris-flow fans in south-western British Columbia, Canada. We mapped 146 debris-flow impact areas over an average observation period of 74 years using orthorectified airphotos, satellite imagery, topographic base maps, LiDAR data, orthophotos, and field observations. We devised a graphical method to convert our geospatial mapping into spatial impact heat maps normalized by fan boundaries, enabling comparison of runout distributions across different fans. About 90% of the mapped debris flows reached beyond the mid-points of fans, while less than 10% avulsed more than half-way across the fan relative to the previous flow path. Most avulsions initiated at distances of 20% to 40% of the maximum fan length from the fan apex and upstream of the fan intersection point. Large volume events tend to be more mobile in the down-fan direction, but the relation between volume and cross-fan runout (e.g., avulsions) is more complex. Differences in spatial impact distributions can be explained, in part, by the degree of fan incision and whether a fan is truncated at its toe by a river or lake. There were no significant differences in spatial impact distributions based on the geology of the source area, sediment supply condition, or hydrogeomorphic process classification.  相似文献   

12.
Debris-flow runout is a fascinating process to understand due to its implications for downstream alluvial fans. Based on the propagation-deposition behaviors of the Dongyuege (DYG) debris flow, in Yunnan, the effect of biofilms on channel surfaces on debris-flow runout is investigated in laboratory flumes with two different internal surfaces: surfaces are lined with granite slabs (Model I) and gravel (Model II), respectively. Our results show that biofilms can significantly reduce frictional resistance to flows. They increase flow velocities, slow down the deceleration of the snouts, prolong runout distances, and subsequently extend the areas covered with resulting deposits, thus greatly assisting the propagation of experimental debris flows. Slippery biofilms consisting mainly of diatoms and their extracellular mucus (ECM) reduce the contact friction between the flume-beds and the overlying fluids, and greatly promote the propagation of tested flows. Well-developed biofilms are found on the underwater channel surfaces of the DYG Creek. Acting as lubricating layers, they likely played a key role in the DYG debris-flow runout. Most of the debris transported during the DYG event was deposited on overbanks, and the sediment that caused the disaster was transported to the populated fan region through the stream-bed clad in the thick biofilms. Owing to their impacts on the development and width of the temporary debris dam breach, the stream-bed covered with biofilms became a direct contributor to the debris-flow hazard. Because of the ubiquitous presence of biofilms on mountain stream-bed surfaces, the development of perennial streamflows can be viewed as an indicator of gully susceptibility to debris flows threatening creek fans. The underwater areas of pre-event channel cross-sections should be regarded as slip or low-friction boundaries, and the parts above stream-levels can be viewed as no-slip boundaries. © 2019 John Wiley & Sons, Ltd.  相似文献   

13.
The effect of the small fraction of clays on the rheological behaviour of alpine debris flow is poorly understood. This is partly due to the complexity of the debris flow mineralogy and the broad particle size distribution. This study has investigated this issue by simulating an alpine debris flow with a mixture of well characterized fractions and then varying the clay fraction composition. Four samples were tested, ranging from a clay fraction made up of only kaolinite (1:1 type clay) to samples where 80 per cent of the kaolinite is replaced by bedeillite (a 2:1 type clay similar to smectite). Changing the content of 2:1 type clay has a strong influence on the behaviour of the whole material, despite its low weight fraction of around 2 per cent. The tests carried out on these reconstituted materials were compared with the results obtained for natural debris flow materials and showed some common trends: in particular, the rheological parameters for materials with and without 2:1 clays with respect to yield stress as a function of solid content. Copyright © 2006 John Wiley & Sons, Ltd.  相似文献   

14.
Mass exchange between debris flow and the bed plays a vital role in debris flow dynamics. Here a depth‐averaged two‐phase model is proposed for debris flows over erodible beds. Compared to previous depth‐averaged two‐phase models, the present model features a physical step forward by explicitly incorporating the mass exchange between the flow and the bed. A widely used closure model in fluvial hydraulics is employed to estimate the mass exchange between the debris flow and the bed, and an existing relationship for bed entrainment rate is introduced for comparison. Also, two distinct closure models for the bed shear stresses are evaluated. One uses the Coulomb friction law and Manning's equation to determine the solid and fluid resistances respectively, while the other employs an analytically derived formula for the solid phase and the mixing length approach for the fluid phase. A well‐balanced numerical algorithm is applied to solve the governing equations of the model. The present model is first shown to reproduce average sediment concentrations in steady and uniform debris flows over saturated bed as compared to an existing formula underpinned by experimental datasets. Then, it is demonstrated to perform rather well as compared to the full set of USGS large‐scale experimental debris flows over erodible beds, in producing debris flow depth, front location and bed deformation. The effects of initial conditions on debris flow mass and momentum gain are resolved by the present model, which explicitly demonstrates the roles of the wetness, porosity and volume of bed sediments in affecting the flow. By virtue of extended modeling cases, the present model produces debris flow efficiency that, as revealed by existing observations and empirical relations, increases with initial volume, which is enhanced by mass gain from the bed. Copyright © 2017 John Wiley & Sons, Ltd.  相似文献   

15.
The water budget in clay shale terrain is controlled by a complex interaction between the vertisol soil layer, the underlying fractured rock, land use, topography, and seasonal trends in rainfall and evapotranspiration. Rainfall, runoff, lateral flow, soil moisture, and groundwater levels were monitored over an annual recharge cycle. Four phases of soil–aquifer response were noted over the study period: (1) dry‐season cracking of soils; (2) runoff initiation, lateral flow and aquifer recharge; (3) crack closure and down‐slope movement of subsurface water, with surface seepage; (4) a drying phase. Surface flow predominated within the watershed (25% of rainfall), but lateral flow through the soil zone continued for most of the year and contributed 11% of stream flow through surface seepage. Actual flow through the fractured shale makes up a small fraction of the water budget but does appear to influence surface seepage by its effect on valley‐bottom storage. When the valley soil storage is full, lateral flow exits onto the valley‐bottom surface as seasonal seeps. Well response varied with depth and hillslope position. FLOWTUBE model results and regional recharge estimates are consistent with an aquifer recharge of 1·6% of annual precipitation calculated from well heights and specific yield of the shale aquifer. Copyright © 2005 John Wiley & Sons, Ltd.  相似文献   

16.
The main purpose of this study is to develop a new type of artificial neural network based model for constructing a debris flow warning system. The Chen‐Eu‐Lan river basin, which is located in Central Taiwan, is assigned as the study area. The creek is one of the most well‐known debris flow areas where several damaging debris flows have been reported in the last two decades. The hydrological and geological data, which might have great influence on the occurrence of debris flows, are first collected and analysed, then, the shared near neighbours neural network (SNN + NN) is presented to construct the debris flow warning system for the watershed. SNN is an unsupervised learning method that has the advantage of dealing with non‐globular clusters, besides presenting computational efficiency. By using SNN, the compiled hydro‐geological data set can easily and meaningfully be clustered into several categories. These categories can then be identified as ‘occurrence’ or ‘no‐occurrence’ of debris flows. To improve the effectiveness of the debris flow warning system, a neural network framework is designed to connect all the clusters produced by the SNN method, whereas the connected weights of the network are adjusted through a supervised learning method. This framework is used and its applicability and practicability for debris flow warning are investigated. The results demonstrate that the proposed SNN + NN model is an efficient and accurate tool for the development of a debris flow warning system. Copyright © 2007 John Wiley & Sons, Ltd.  相似文献   

17.
The dynamics and the surface evolution of a post‐LGM debris‐flow‐dominated alluvial fan (Tartano alluvial fan), which lies on the floor of an alpine valley (Valtellina, Northern Italy), have been investigated by means of an integrated study comprising geomorphological field work, a sedimentological study, photointerpretation, quantitative geomorphology, analysis of ancient to modern cartography and consultation of historical documents and records. The fan catchment meteoclimatic, geological and geomorphological characteristics result in fast rates of geomorphic reorganization of the fan surface (2 km2). The dynamics of the fan are determined by the alternation of low‐return period catastrophic alluvial events dominated by non‐cohesive debris flows triggered by extreme rainstorms which caused aggradation and steepening of the fan and avulsion of its main channel, with periods of low to moderate streamflow discharge punctuated by low‐ to intermediate‐magnitude flood events, causing slower but steady topographic reworking. The most ancient parts of the fan surface date back at least to the first half of the 19th century, but most of the fan surface has been restructured after 1911, mainly during the debris‐flow‐dominated events of 1911 and 1987. Phases of rapid fan toe incision and fan degradation have been recognized; since the 1930s or 1940s, the Tartano fan has been subjected to a state of deep entrenchment and narrowing of the main trunk channel and distributary area. Post‐Little Ice Age climate change and present‐day surface uplift rates have been considered as possible explanations for the observed geomorphic evolution, but tectonic or climatic controls cannot account for the order of magnitude of the erosional pace. Anthropogenic controls plausibly override the natural ones: in particular, the building of a dam in the late 1920s, about 2 km upstream of the fan, seems to have triggered fan dissection, having altered the sediment discharge through sediment retention. Copyright © 2011 John Wiley & Sons, Ltd.  相似文献   

18.
The debris deposits at the bottom of very steep natural channels and streams in high mountain areas can be mobilized by runoff, triggering a water–sediment mixture flow known as debris flow. The routing of debris flow through human settlements can cause damage to civil structures and loss of human lives. The prediction of such an event, or the runoff discharge that triggers it, assumes an interest in risk analyses and the planning of defence measures. The object of this study is to find a method to determine the critical runoff value that triggers debris flow as a result of channel‐bed failure. Historical and rainfall data on 30 debris flows that occurred in six watersheds of the Dolomites (north‐eastern Italian Alps) were collected from different sources. Field investigations at the six sites, together with the hydrologic response to the rainfalls that triggered the events, were performed to obtain a realistic scenario of the formation of the debris flow there occurred. Field observations include a survey along the channel of the triggering reach of debris flow, with measurements of the channel slope and cross‐section and sampling of debris deposits for grain size distribution. Simulated runoff discharge values based on the rainfall recorded by pluviometers were then compared with values obtained through experimental criteria on the initiation and formation of debris flow by bed failure. The results are discussed to provide a plausible physical‐based method for the prediction of the triggering of debris flow by channel‐bed failure. Copyright © 2007 John Wiley & Sons, Ltd.  相似文献   

19.
This study proposes a sediment‐budget model to predict the temporal variation of debris volume stored in a debris‐flow prone watershed. The sediment‐budget is dominated by shallow landslides and debris outflow. The basin topography and the debris volume stored in the source area of the debris‐flow prone watershed help evaluating its debris‐flow susceptibility. The susceptibility model is applied to the Tungshih area of central western Taiwan. The importance of the debris volume in predicting debris‐flow susceptibility is reflected in the standardized coefficients of the proposed statistical discriminant model. The high prediction rate (0·874) for the occurrence of debris flows justifies the capability of the proposed susceptibility models to predict the occurrence of debris flows. This model is then used to evaluate the temporal evolution of the debris‐flow susceptibility index. The analysis results show that the numbers of watershed which are classified as a debris‐flow group correspond well to storage of sediment at different time periods. These numbers are 10 before the occurrence of Chi‐Chi earthquake, 13 after the occurrence of Chi‐Chi earthquake, 16 after the occurrence of landslides induced by Typhoon Mindulle (Typhoon M), and 14 after the occurrence of debris flows induced by Typhoon M. It indicates that the occurrence of 7·6 Chi‐Chi earthquake had significant impact on the debris flow occurrence during subsequent typhoons. Copyright © 2009 John Wiley & Sons, Ltd.  相似文献   

20.
The assessment of the dominant flow type on alluvial fans usually refers to two categories: debris‐flow fans (i.e. sediment gravity flows) and fluvial fans (i.e. fluid gravity flows). Here we report the results of combined morphometric, stratigraphic and sedimentological approaches which suggest that hyperconcentrated flows, a transitional process rheologically distinct from debris flows and floods and sometimes referred to as debris floods, mud floods, or transitional debris flows, are the dominant fan building process in eastern Canada. These flows produce transitional facies between those of debris flows which consist of a cohesive matrix‐supported diamicton, and those of river flows which display more distinct stratification. The size of the blocks in the channels and the abrasion scars at the base of several trees attest to the high transport capacity of these flows. The fan channels are routed according to various obstacles comprised primarily of woody debris that impede sediment transit. However, these conditions of sediment storage are combined with readily available sediment due to the friable nature of the local lithology. Tree‐ring analysis allowed the reconstruction of eight hydrogeomorphic events which are characterized by a return period of 9.25 years for the period 1934–2008, although most of the analyzed events occurred after 1970. Historical weather data analysis indicates that they were related to rare hydrometeorological events at regional and local scales. This evidence led to the elaboration of weather scenarios likely responsible for triggering flows on the fan. According to these scenarios, two distinct hydrologic regimes emerge: the torrential rainfall regime and the nival regime related to snowmelt processes. Hydrogeomorphic processes occurring in a cold‐temperate climate, and particularly on small forested alluvial fans of north‐eastern North America, should receive more attention from land managers given the hazard they represent, as well as because of their sensitivity to various meteorological parameters. Copyright © 2014 John Wiley & Sons, Ltd.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号