共查询到20条相似文献，搜索用时 15 毫秒
1.
Jie Cheng Shunlin Liang Hao Liu Aixiu Nie Qiang Liu 《International Journal of Digital Earth》2018,11(7):691-702
High spatial resolution land surface broadband emissivity (BBE) is not only useful for surface energy balance studies at local scales, but also can bridge the gap between existing coarser resolution BBE products and point-based field measurements. This study proposes a disaggregation approach that utilizes the established BBE–reflectance relationship for estimating high spatial resolution BBE for bare soils from Landsat surface reflectance data. The disaggregated BBE is compared to the BBE calculated from spatial–temporal matched Advanced Spaceborne Thermal Emission and Reflectance Radiometer emissivity product. Comparison results show that better agreement is achieved over relative homogeneous areas, but deteriorated over heterogeneous and cloud-contaminated areas. In addition, field-measured emissivity data over large homogeneous desert were also used to validate the disaggregated BBE, and the bias is 0.005. The comparison and validation results indicated that the disaggregation approach can obtain high spatial resolution BBE with better accuracy for homogeneous area. 相似文献
2.
Cristian Mattar Andrés Santamaría-Artigas Flavio Ponzoni Cibele T. Pinto Carolina Barrientos Glynn Hulley 《International Journal of Digital Earth》2019,12(1):43-61
This work presents the preliminary results of the first field calibration campaign performed in the Atacama Desert, Chile, between the 18 and 22 August 2014, called the Atacama Field Campaign (ATAFIC 2014). In situ measurements were performed in order to spectrally characterize the surface reflectance spectra between 0.3 and 2.5?µm, radiometric temperature (8.0–14.0?µm) and atmospheric measurements. A soil sample was collected and analyzed using Fourier Transform Infrared Spectroscopy and X-Ray Diffraction techniques to characterize the surface reflectance spectra and mineralogical composition, respectively. ASTER land surface emissivity in addition to GOES, MODIS and Landsat-8 land surface temperature (LST) were also used. Results showed that the spectral features of the Atacama soil and the characteristics of this geographical zone, which is featured as the most hyper-arid and cloudless place in the world, make this area a potential target for surface reflectance characterization. Day and night LST comparison between field and remote sensing data are lower than 2?K and the Root Mean Square Error for land surface emissivity is close to 2%. This work opens the possibilities to consider the Atacama Desert as a reference target for calibration and validation activities for earth observation missions’ purposes. 相似文献
3.
基于ASTER GED产品的地表发射率估算 总被引：1，自引：0，他引：1
地表发射率是地表温度反演的重要输入参数,为了解决现有地表发射率估算方法在裸露地表精度较差的问题,本文基于最新的ASTER全球地表发射率产品(ASTER GED)和基于植被覆盖度的方法(VCM),提出了一个改进的地表发射率估算方法。首先,利用ASTER GED产品求解裸土发射率,然后,利用ASTER波谱库中的植被发射率和植被覆盖度结合VCM方法计算地表发射率。利用张掖地区2012年11景ASTER TES算法反演的地表发射率产品和实测地表发射率数据进行了验证,同时利用一景Landsat 8 TIRS数据分析了对地表温度反演精度的影响。结果表明该方法估算的地表发射率整体精度较高,可以有效改进裸露地表的发射率估算精度,用于支持利用多种热红外传感器数据生产高精度的地表温度产品。 相似文献
4.
In this study, the multi-resolution Kalman filter (MKF) algorithm, which can handle multi-resolution problems with high computational efficiency, was used to blend two emissivity products: the Global LAnd Surface Satellite (GLASS) (BBE) product and the Advanced Spaceborne Thermal Emission and Reflection Radiometer (ASTER) narrowband emissivity (NBE) product. The ASTER NBE product was first converted into a BBE product. A new detrending method was used to transfer the BBEs into a process suitable for the MKF. The new detrending method was superior to the two existing methods. Finally, both the de-trended GLASS and ASTER BBE products were incorporated into the MKF framework to obtain the optimal estimation at each scale. Field measurements collected in North America were used to validate the integrated BBEs. Visually, the fusion map showed good continuity, with the exception of the border areas, and the quality of the fusion map was better than that of the original maps. The validation results indicate that the MKF improved the BBE product accuracy at the coarse scale. In addition, the MKF was capable of recovering missing pixels at a finer scale. 相似文献
5.
海陆表面温度是理解全球变化与人类活动的关键参数。针对已有温度反演产品海陆边界时空不连续的问题,本文采用Sentinel-3海陆表面温度辐射计(SLSTR)光学与热红外影像,通过植被指数阈值法逐像元计算陆表与海表发射率,基于分裂窗算法反演得到黄河三角洲陆海表面时空连续温度产品。结合地面温度观测和欧洲中期天气预报中心提供的全球中等分辨率数值大气再分析产品,验证了本文陆海温度产品(均方根误差优于1.1K)反演精度高于现有公开的全球产品,可为全球时空连续温度产品反演提供参考。 相似文献
6.
真实性检验是评价遥感反演产品质量和验证遥感应用产品是否准确、真实地反映实际情况的重要途径。叶面积指数(LAI)是表征陆地植被结构和长势的关键参数,全面准确评价和验证LAI产品是产品用于陆面过程模型的前提。本文以MODIS LAI与GLASS LAI产品为研究对象,在尺度效应和尺度转换的基础上,建立了针对非均匀像元的低分辨率LAI产品真实性检验方法。在考虑空间异质性和植被长势差异的情况下,借助中分辨率的遥感影像,分别利用1 km像元平均叶面积指数和反演表观叶面积指数实现了对LAI算法和产品的真实性检验。为了比较作物长势差异和地表非均匀度对产品的影响,本文选择有代表性的河南鹤壁和甘肃张掖两个地区进行两种LAI产品真实性检验研究。研究结果表明,GLASS LAI和MODIS LAI产品均存在明显的低估现象。这并不是产品算法的问题,而是由于地表异质性和非均匀度的影响。在异质性更显著的张掖盈科灌区,低估现象更明显。GLASS LAI产品是多种LAI产品的融合,它的平均LAI比MODIS更接近真实情况,但是LAI的动态范围比MODIS窄。 相似文献
7.
A long-term Global LAnd Surface Satellite (GLASS) data-set for environmental studies 总被引：1，自引：0，他引：1
《International Journal of Digital Earth》2013,6(6):5-33
Recently, five Global LAnd Surface Satellite (GLASS) products have been released: leaf area index (LAI), shortwave broadband albedo, longwave broadband emissivity, incident short radiation, and photosynthetically active radiation (PAR). The first three products cover the years 1982–2012 (LAI) and 1981–2010 (albedo and emissivity) at 1–5 km and 8-day resolutions, and the last two radiation products span the period 2008–2010 at 5 km and 3-h resolutions. These products have been evaluated and validated, and the preliminary results indicate that they are of higher quality and accuracy than the existing products. In particular, the first three products have much longer time series, and are therefore highly suitable for various environmental studies. This paper outlines the algorithms, product characteristics, preliminary validation results, potential applications and some examples of initial analysis of these products. 相似文献
8.
Angular effect of MODIS emissivity products and its application to the split-window algorithm 总被引：1，自引：0，他引：1
Huazhong RenGuangjian Yan Ling ChenZhaoliang Li 《ISPRS Journal of Photogrammetry and Remote Sensing》2011,66(4):498-507
The angular effects of emissivity are ignored in current land surface temperature (LST) products. As a result, the directionality of these LST products limits their further application in many fields. Accurate correction of the angular problem of LST products requires explicit understanding of the angular effects of emissivity at the pixel scale. Currently, nearly ten years of global emissivity products of MODIS are available. However, the pixel-scale directionality of emissivity has never been analyzed. By performing a statistical analysis of 5-year MODIS emissivity products over most of East Asia, we generated the empirical relationships between the directional emissivity, land cover, and seasonal variations. Two look-up tables (LUTs) of directional emissivity were created for typical land cover types and applied to the generalized split-window algorithm to modify the MODIS LST. The results showed that the angular effect of emissivity could introduce a significant bias of −1-3 K to the 1 km resolution LST. Finally, the spatial scale effects of emissivity were analyzed, and it was found that the temperature differences caused by scale effects fell within +/−0.5 K for most pixels if 5 km emissivity was used in 1 km LST retrieval. Therefore, wide use of the LUTs can be expected. 相似文献
9.
对多源遥感数据协同生产的2010年—2015年中国区域1 km空间分辨率5天合成的MuSyQ（Multi-source data Synergized Quantitative remote sensing production system）叶面积指数LAI产品进行验证。参考现有的LAI产品（MODIS c5,GLASS LAI）和中国生态系统研究网络部分农田和森林站点可用的LAI地面测量数据,从时空连续性、时空一致性、精度和准确性等方面对中国区域的MuSyQ LAI产品进行定性和定量分析与评价。结果表明：（1） MuSyQ LAI产品在保证精度优于MODIS产品的情况下,时间分辨率和时空连续性均有提高。MuSyQ LAI与其他LAI产品（MODIS c5,GLASS LAI）在整体上有很好的一致性（RMSE=1.0,RMSE=0.81）,但对常绿阔叶林高值处的描述不稳定;（2） 与LAI地面测量数据相比,MuSyQ LAI产品与地面参考图对比结果较好（最高相关性（R2=0.54）和较低总体误差（RMSE=0.96））,其在阔叶作物生长季高值处有些许低估且在某些阔叶林站点有些高估。整体上,MuSyQ LAI产品呈现出较高的精度,可靠的空间分布和连续稳定的时间分布,且对森林LAI的描述具有更可靠的动态范围。 相似文献
10.
地表温度作为研究环境生态影响的一个重要指标之一,以Landsat ETM+的热红外波段作为数据源,辅助大气透过率、大气平均气温等参数,利用单窗算法基于混合像元、NDVI、植被和裸露地三种不同地表比辐射率反演泉州市地表温度,对比分析结果表明采用这三种地表比辐射率反演地表温度的方法均是可行的,对于具体采用哪一种地表比辐射率应需要结合实际的研究区域地表地物的实际监测地表温度进行对比后,方可选择合适的地表比辐射率进行地表温度反演,会更具实际意义。反演结果可为城市热岛效应等研究提供支持数据源。 相似文献
11.
用被动微波AMSR数据反演地表温度及发射率的方法研究 总被引：8，自引：1，他引：8
针对对地观测卫星多传感器的特点，提出了借助MODIS地表温度产品从被动微波数据中反演地表温度的方法。即利用MODIS地表温度产品和AMSR不同通道之间的亮度温度，建立地表温度的反演方程。该方法克服了以往需要测量同步数据的困难，为不同传感器之间的参数反演相互校正和综合利用多传感器的数据提供实际应用和理论依据。文中以MODIS地表温度产品作为评价标准，对方法进行检验，其平均误差为2~3℃。另外，微波的发射率是土壤水分反演的关键参数，在对微波地表温度反演的基础上，进一步对发射率进行了研究。 相似文献
12.
地表发射率不同的估算方法对地表温度的影响 总被引：1，自引：0，他引：1
随着遥感技术的日益成熟,用热红外波段反演地表温度的方法也日趋完善,其中一个关键参数--地表发射率的估算,直接影响着地表温度的反演结果。基于TM6的热红外波段,分别采用最常用的Van的地表发射率估算方法和综合了覃志豪与Sobrino的估算方法,对北京地区的地表温度进行了反演,并在此基础上对这2种估算方法所得结果进行了比较,从而为找出更为有效的地表发射率估算公式提供依据。结果表明,对于农林地2种估算方法都比较适合,但是对于水体和城市等人口密集地区,则需要和当地的实测数据进行比对,从而确定更为合适有效的估算方法,以得到更为精确的地表温度结果。 相似文献
13.
地表参数定量遥感反演是遥感科学研究的重要环节.21世纪以来,地球静止气象卫星数据在地表参数遥感反演中受到越来越多的重视.本文对利用地球静止气象卫星进行地表参数遥感反演研究的进展进行了综述.文章首先简单介绍了当前正在运行的欧盟Meteosat、美国GOES-R、日本葵花和中国风云静止卫星系统,随后详细总结了不同卫星系统估... 相似文献
14.
关键陆表参数遥感产品真实性检验方法研究进展 总被引：1，自引：0，他引：1
遥感产品真实性检验是定量遥感基础研究的重要环节,是客观评价遥感产品精度、稳定性和一致性的重要手段,对于提高遥感定量化水平、推动和扩展遥感产品的深化应用具有重要的意义。本文基于当前陆表参数遥感产品真实性检验研究的相关成果,归纳总结了陆表参数遥感产品真实性检验方法,并就其中的5种真实性检验方法,即基于地面单点测量检验、基于地面多点采样检验、基于高分辨率数据的检验、交叉检验和间接检验,阐述了各方法的特点、局限性、适用条件。文章在最后探讨了陆表关键参数遥感产品真实性检验评价指标和验证中影响精度评价的关键因素。本文对于遥感产品真实性检验工作的开展和真实性检验系统研发具有重要的指导意义。 相似文献
15.
16.
冰雪反照率是影响和评估全球气候变化的重要因子。北极格陵兰岛拥有世界第二大冰盖,定量获取该地区反照率是研究北半球能量收支变化的关键。全球陆表卫星(global land surface satellite,GLASS)产品系统生产的反照率产品是目前国际上时间序列最长（1981—2017年）的全球反照率产品。利用格陵兰气候观测网络(Greenland climate network, GC-Net)与格陵兰冰架监测计划(programme for monitoring of the Greenland ice sheet, PROMICE)网络观测的反照率数据,评估了格陵兰地区GLASS地表反照率产品的精度;并基于2000—2017年的GLASS地表反照率产品,分析了格陵兰地区7月份反照率的年际变化趋势与空间分布特征。结果表明：GLASS与GC-Net反照率的均方根误差(root mean squared error, RMSE)为0.077 8(决定系数R2=0.490 7),与PROMICE反照率差异的RMSE为0.078 6(R2=0.899 9),GLASS产品的反照率数值呈现一定... 相似文献
17.
作为驱动地表与大气之间能量交换的关键物理量,地表温度在众多领域中都发挥着重要作用,包括气候变化、环境监测、蒸散发估算以及地热异常勘探等。Landsat热红外数据因其时间连续性和高空间分辨率等特点被广泛应用于地表温度反演中。本文详细地介绍了Landsat热红外传感器及其可用的数据与产品的现状,梳理了2001年—2020年20年间基于Landsat热红外数据的地表温度遥感反演与应用的相关文献发表及互引情况,系统地综述了基于Landsat热红外数据的地表温度反演算法,包括基于辐射传输方程的算法、单窗算法、普适性单通道算法、实用单通道算法和分裂窗算法等。在此基础上,进一步介绍了每种算法的参数化方案,包括地表比辐射率和大气参数的估算方法。最后针对Landsat热红外数据地表温度遥感反演提出了未来可能的发展趋势与研究方向。 相似文献
18.
地表温度与发射率是地表—大气系统长波辐射和潜热通量交换的直接驱动力,是描述区域和全球尺度上地表能量平衡与水平衡的重要参数,其时空变化信息在气象预测、气候变化、水循环、地质勘探、农林监测和城市热环境等诸多领域具有广泛的应用。热红外遥感作为当前获取区域或全球尺度上地表温度和发射率的最有效手段之一,相较于传统的地面点位测量方法,具有空间覆盖范围大和重复观测等优势。对热红外遥感定量反演的地表温度与发射率产品进行地表真实性验证,有利于发现遥感数据自身或其反演算法的缺陷,确定产品的精度与不确定度,便于遥感产品的应用与推广。本文首先回顾了地表温度和发射率的定义,阐述了热红外遥感可反演、地面可测量的地表温度和发射率的科学内涵,并对利用热红外遥感数据反演地表温度和发射率的理论和方法作了概述;对地表温度和发射率地面验证的框架体系、验证指标进行总结,建立了基于精度、精确度、不确定度、完整性和稳定性的验证评价指标体系;总结了地表温度和地表发射率的地面验证方法、地面测量方法、辅助数据的获取方法、地表温度地面测量的采样方法,以及在验证异质非同温地表时从点到像元尺度的地表温度尺度转换方法等,分析了地面验证过程的主要误差来源;归纳了目前地表温度和地表发射率主要验证站点、观测网络及其空间分布特征;最后,本文讨论了地表温度与发射率地面验证存在的若干问题,并对地表温度与发射率验证工作的发展前景和趋势进行了相关展望。 相似文献
19.
We have delineated different granitoids based on variation in emissivity and relative surface temperature recorded in thermal bands of Advanced Spaceborne Thermal Emission and Reflection Radiometer (ASTER) sensor of EO-1 satellite. In this regard, we have used emissivity normalization algorithm to derive broadband emissivity from thermal bands of ASTER sensor to delineate different lithounits of the granitoid family. We have compared emissivity and radiance image composites in terms of delineation of different granitoids. We have also used false colour composite (FCC) image derived using two emissivity bands and temperature (derived using emissivity normalisation method) bands to delineate different granitoids. We could differentiate different granitoids in the three-dimensional (3D) data space of ASTER-derived emissivity bands (second and third bands) and temperature bands. Based on the analysis of 3D scatter plot, we also proposed a ternary diagram of emissivity and temperature, which can be used to delineate different granitoids. 相似文献
20.
The validation study of leaf area index (LAI) products over rugged surfaces not only gives additional insights into data quality of LAI products, but deepens understanding of uncertainties regarding land surface process models depended on LAI data over complex terrain. This study evaluated the performance of MODIS and GLASS LAI products using the intercomparison and direct validation methods over southwestern China. The spatio-temporal consistencies, such as the spatial distributions of LAI products and their statistical relationship as a function of topographic indices, time, and vegetation types, respectively, were investigated through intercomparison between MODIS and GLASS products during the period 2011–2013. The accuracies and change ranges of these two products were evaluated against available LAI reference maps over 10 sampling regions which standed for typical vegetation types and topographic gradients in southwestern China.The results show that GLASS LAI exhibits higher percentage of good quality data (i.e. successful retrievals) and smoother temporal profiles than MODIS LAI. The percentage of successful retrievals for MODIS and GLASS is vulnerable to topographic indices, especially to relief amplitude. Besides, the two products do not capture seasonal dynamics of crop, especially in spring over heterogeneously hilly regions. The yearly mean LAI differences between MODIS and GLASS are within ±0.5 for 64.70% of the total retrieval pixels over southwestern China. The spatial distribution of mean differences and temporal profiles of these two products are inclined to be dominated by vegetation types other than topographic indices. The spatial and temporal consistency of these two products is good over most area of grasses/cereal crops; however, it is poor for evergreen broadleaf forest. MODIS presents more reliable change range of LAI than GLASS through comparison with fine resolution reference maps over most of sampling regions. The accuracies of direct validation are obtained for GLASS LAI (r = 0.35, RMSE = 1.72, mean bias = −0.71) and MODIS LAI (r = 0.49, RMSE = 1.75, mean bias = −0.67). GLASS performs similarly to MODIS, but may be marginally inferior to MODIS based on our direct validation results. The validation experience demonstrates the necessity and importance of topographic consideration for LAI estimation over mountain areas. Considerable attention will be paid to the improvements of surface reflectance, retrieval algorithm and land cover types so as to enhance the quality of LAI products in topographically complex terrain. 相似文献