首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献，搜索用时 828 毫秒
1.
This paper presents the results of extensive field trials measuring rates of Fe(II) oxidation at a number of Fe-bearing mine drainage discharges in the UK. Batch experiments were carried out with samples taken at regular intervals and Fe(II) concentration determined spectrophotometrically using 2′2-bipyridyl as the complexing agent. Initial concentrations for Fe(II) were 5.65-76.5 mg/L. Temperature, pH and dissolved O2 (DO) were logged every 10 s, with pH at the start of the experiments in the range 5.64-6.95 and alkalinity ranging from 73 to 741 mg/L CaCO3 equivalent. A numerical model based on a fourth order Runge-Kutta method was developed to calculate values for k1, the rate constant for homogeneous oxidation, from the experimental data. The measured values of pH, temperature, [Fe(II)] and DO were input into the model with resulting values for k1 found to be in the range 2.7 × 1014-2.7 × 1016 M−2 atm−1 min−1. These values for k1 are 1-3 orders of magnitude higher than previously reported for laboratory studies at a similar pH. Comparison of the observed Fe(II) oxidation rates to data published by other authors show a good correlation with heterogenous oxidation rates and may indicate the importance of autocatalysis in these systems. These higher than expected rates of Fe oxidation could have a significant impact on the design of treatment schemes for the remediation of mine drainage and other Fe-bearing ground waters in the future.  相似文献   

2.
The rates of Fe(II) oxidation and precipitation from groundwater are highly pH dependent. Elevated levels of dissolved CO2 can depress pH and cause difficulty in removing dissolved Fe and associated metals during treatment of ferruginous water. This paper demonstrates interdependent changes in pH, dissolved inorganic C species, and Fe(II) oxidation rates that occur as a result of the removal (degassing) of CO2 during aeration of waters discharged from abandoned coal mines. The results of field monitoring of aeration cascades at a treatment facility as well as batchwise aeration experiments conducted using net alkaline and net acidic waters in the UK are combined with geochemical modelling to demonstrate the spatial and temporal evolution of the discharge water chemistry. The aeration cascades removed approximately 67% of the dissolved CO2 initially present but varying the design did not affect the concentration of Fe(II) leaving the treatment ponds. Continued removal of the residual CO2 by mechanical aeration increased pH by as much as 2 units and resulted in large increases in the rates of Fe(II) oxidation and precipitation. Effective exsolution of CO2 led to a reduction in the required lime dose for removal of remaining Fe(II), a very important factor with regard to increasing the sustainability of treatment practices. An important ancillary finding for passive treatment is that varying the design of the cascades had little impact on the rate of CO2 removal at the flow rates measured.  相似文献   

3.
《Chemical Geology》2006,225(1-2):16-29
Pyrite oxidation rates were examined at various concentrations of dissolved oxygen (DO) in the presence of the sulfur and iron oxidizer Acidithiobacillus ferrooxidans. Five different batch experiments were performed at room temperature for 75 days under various DO levels (273, 129, 64.8, 13.2, and ≤ 0.006 μM), containing pyrite grains (particle size 63–250 μm) and a modified 9K nutrient medium at pH 3. The reactors were inoculated with A. ferrooxidans. In all experiments, pH decreased with time and sulfur and iron were released to the solution, indicating pyrite oxidation at all DO levels. Pyrite oxidation rates (ca. 5 × 10− 10 mol m− 2 s− 1 at 273 μM DO) from all experiments showed positive correlation with DO, Fe(III), and bacterial concentration. These rates were significantly slower than rates presented in other published studies, but this is probably due to the significantly greater Fe(III) concentration at lower pH in these previous studies. The results obtained in this study suggest that ferric iron reduction at the pyrite surface is the primarily mechanism for microbial pyrite oxidation in the presence of DO. The results from our study support the indirect mechanism of sulfide oxidation, where A. ferrooxidans oxidizes ferrous iron in the presence of DO, which then oxidizes pyrite.  相似文献   

4.
Fe(III) solid phases are the products of Fe(II) oxidation by Fe(II)-oxidizing bacteria, but the Fe(III) phases reported to form within growth experiments are, at times, poorly crystalline and therefore difficult to identify, possibly due to the presence of ligands (e.g., phosphate, carbonate) that complex iron and disrupt iron (hydr)oxide precipitation. The scope of this study was to investigate the influences of geochemical solution conditions (pH, carbonate, phosphate, humic acids) on the Fe(II) oxidation rate and Fe(III) mineralogy. Fe(III) mineral characterization was performed using 57Fe-Mössbauer spectroscopy and μ-X-ray diffraction after oxidation of dissolved Fe(II) within Mops-buffered cell suspensions of Acidovorax sp. BoFeN1, a nitrate-reducing, Fe(II)-oxidizing bacterium. Lepidocrocite (γ-FeOOH) (90%), which also forms after chemical oxidation of Fe(II) by dissolved O2, and goethite (α-FeOOH) (10%) were produced at pH 7.0 in the absence of any strongly complexing ligands. Higher solution pH, increasing concentrations of carbonate species, and increasing concentrations of humic acids promoted goethite formation and caused little or no changes in Fe(II) oxidation rates. Phosphate species resulted in Fe(III) solids unidentifiable to our methods and significantly slowed Fe(II) oxidation rates. Our results suggest that Fe(III) mineralogy formed by bacterial Fe(II) oxidation is strongly influenced by solution chemistry, and the geochemical conditions studied here suggest lepidocrocite and goethite may coexist in aquatic environments where nitrate-reducing, Fe(II)-oxidizing bacteria are active.  相似文献   

5.
Passive treatment systems for mine drainage use no energy other than gravity, but they require greater area than active treatment systems. Researchers are considering “hybrid” systems that have passive and active components for increased efficiency, especially where space limitations render passive-only technology ineffective. Flow-through reactor field experiments were conducted at two large net-alkaline anthracite mine discharges in central Pennsylvania. Assuming an Fe removal rate of 20 g m−2 day−1 and Fe loading from field data, 3.6 × 103 and 3.0 × 104 m2 oxidation ponds would be required for the passive treatment of Site 21 and Packer 5 discharges, respectively. However, only a small area is available at each site. This paper demonstrates aeration to drive off CO2, increase pH, and increase Fe(II) oxidation rates, enabling treatment within a small area compared to passive treatment methods, and introduces a geochemical model to accurately predict these rates as well as semi-passive treatment system sizing parameters. Both net-alkaline discharges were suboxic with a pH of ≈5.7, Fe(II) concentration of ≈16 mg L−1, and low Mn and Al concentrations. Flow rates were ≈4000 L min−1 at Site 21 and 15,000 L min−1 at Packer 5. Three-h aeration experiments with flow rates scaled to a 14-L reactor resulted in pH increases from 5.7 to greater than 7, temperature increases from 12 to 22 °C, dissolved O2 increases to saturation with respect to the atmosphere, and Fe(II) concentration decreases from 16 to <0.05 mg L−1. A 17,000-L pilot-scale reactor at Site 21 produced similar results although aeration was not as complete as in the smaller reactor. Two non-aerated experiments at Site 21 with 13 and 25-h run times resulted in pH changes of ?0.2 and Fe(II) concentration decreases of less than 3 mg L−1.  相似文献   

6.
Interpretation of the origins of iron-bearing minerals preserved in modern and ancient rocks based on measured iron isotope ratios depends on our ability to distinguish between biological and non-biological iron isotope fractionation processes. In this study, we compared 56Fe/54Fe ratios of coexisting aqueous iron (Fe(II)aq, Fe(III)aq) and iron oxyhydroxide precipitates (Fe(III)ppt) resulting from the oxidation of ferrous iron under experimental conditions at low pH (<3). Experiments were carried out using both pure cultures of Acidothiobacillus ferrooxidans and sterile controls to assess possible biological overprinting of non-biological fractionation, and both SO42− and Cl− salts as Fe(II) sources to determine possible ionic/speciation effects that may be associated with oxidation/precipitation reactions. In addition, a series of ferric iron precipitation experiments were performed at pH ranging from 1.9 to 3.5 to determine if different precipitation rates cause differences in the isotopic composition of the iron oxyhydroxides. During microbially stimulated Fe(II) oxidation in both the sulfate and chloride systems, 56Fe/54Fe ratios of residual Fe(II)aq sampled in a time series evolved along an apparent Rayleigh trend characterized by a fractionation factor αFe(III)aq-Fe(II)aq ∼ 1.0022. This fractionation factor was significantly less than that measured in our sterile control experiments (∼1.0034) and that predicted for isotopic equilibrium between Fe(II)aq and Fe(III)aq (∼1.0029), and thus might be interpreted to reflect a biological isotope effect. However, in our biological experiments the measured difference in 56Fe/54Fe ratios between Fe(III)aq, isolated as a solid by the addition of NaOH to the final solution at each time point under N2-atmosphere, and Fe(II)aq was in most cases and on average close to 2.9‰ (αFe(III)aq-Fe(II)aq ∼ 1.0029), consistent with isotopic equilibrium between Fe(II)aq and Fe(III)aq. The ferric iron precipitation experiments revealed that 56Fe/54Fe ratios of Fe(III)aq were generally equal to or greater than those of Fe(III)ppt, and isotopic fractionation between these phases decreased with increasing precipitation rate and decreasing grain size. Considered together, the data confirm that the iron isotope variations observed in our microbial experiments are primarily controlled by non-biological equilibrium and kinetic factors, a result that aids our ability to interpret present-day iron cycling processes but further complicates our ability to use iron isotopes alone to identify biological processing in the rock record.  相似文献   

7.
The oxidation of Fe(II) with H2O2 at nanomolar levels in seawater have been studied using an UV-Vis spectrophotometric system equipped with a long liquid waveguide capillary flow cell. The effect of pH (6.5 to 8.2), H2O2 (7.2 × 10−8 M to 5.2 × 10−7 M), HCO3− (2.05 mM to 4.05 mM) and Fe(II) (5 nM to 500 nM) as a function of temperature (3 to 35 °C) on the oxidation of Fe(II) are presented. The oxidation rate is linearly related to the pH with a slope of 0.89 ± 0.01 independent of the concentration of HCO3−. A kinetic model for the reaction has been developed to consider the interactions of Fe(II) with the major ions in seawater. The model has been used to examine the effect of pH, concentrations of Fe(II), H2O2 and HCO3− as a function of temperature. FeOH+ is the most important contributing species to the overall rate of oxidation from pH 6 to pH 8. At a pH higher than 8, the Fe(OH)2 and Fe(CO3)22− species contribute over 20% to the rates. Model results show that when the concentration of O2 is two orders of magnitude higher than the concentration of H2O2, the oxidation with O2 also needs to be considered. The rate constants for the five most kinetically active species (Fe2+, FeOH+, Fe(OH)2, FeCO3, Fe(CO3)22−) in seawater as a function of temperature have been determined. The kinetic model is also valid in pure water with different concentrations of HCO3− and the conditions found in fresh waters.  相似文献   

8.
Redox transformations of iron in the surface waters of the Gulf of Aqaba, Red Sea, were studied on recurrent cruises from September 2006 to May 2007. Fe(II) concentrations and oxidation kinetics were measured in situ using luminol chemiluminescence. High Fe(II) concentrations of 200-400 pM were recorded in the autumn, followed by low concentrations of 20-130 pM in the winter-spring. A distinct diurnal pattern in Fe(II) concentrations was observed in the autumn with maximum values coinciding with maximum solar irradiance. In situ and in vitro Fe(II) oxidation rates showed temporal and spatial variability that was accounted for by changes in water temperature and pH. Dissolved oxygen was found to be the dominant oxidant in all but one cruise. In situ photoreduction rates (deduced from oxidation rates) were linearly correlated with solar irradiance during the autumn, suggesting that the reducible iron pool was not exhausted even at the strongest irradiances and that it was kept constant throughout the season. Phytoplankton had no discernible influence on Fe(II) production, consumption, or oxidation kinetics. Given the fast oxidation and photoreduction rates of up to 180 pM min−1, the turn-over rates of iron were estimated at 10-30 per day. Such a dynamic Fe redox cycle probably influences the chemical reactivity and bioavailability of iron and may enhance the solubility of the abundant aerosol dust.  相似文献   

9.
Oxidation of sulfides at the Leona Heights Sulfur Mine has resulted in the liberation of acid, SO4 and metals to Leona Creek. Previous research at the site has indicated Fe(II) oxidation at rates faster than would be predicted by abiotic oxidation alone, particularly in the segment of stream between the Adit and Leona Street sample stations. In order to assess the mechanisms responsible for sulfide oxidation, samples were collected for isotopic analysis of water and SO4, the results of which were used to develop a stoichiometric isotope-balance model. This exercise indicated that the percentage of water-derived oxygen in SO4 increased spatially from between 56% and 64% at the Adit to between 71% and 72% at Leona Street, illustrating that increased sulfide oxidation via Fe(III) was occurring within, or as water flows over, the waste rock, relative to water emanating directly from the former mine. The incorporation of water-derived oxygen in SO4 during pyrite oxidation is a process controlled by Fe oxidizing bacteria such as A. ferrooxidans at low pH. The role of bacteria was further supported by estimates of the rate constant for Fe oxidation between sampling stations, yielding values that were approximately 106 faster than abiotic Fe oxidation alone. Stable isotopic analysis of water further indicates a close correlation of adit spring water to the local meteoric water line, while 3H data indicate a groundwater apparent age, or time of travel from its primary zone of recharge, of <5–18 a. Additionally, the δ34S data, in conjunction with reported albitized feldspars within the Leona Rhyolite host rock, indicate a magmatic origin of ore sulfur, contrary to previous interpretations at the site.  相似文献   

10.
《Applied Geochemistry》1998,13(4):509-520
A gravity-fed, battery-powered, portable continuously-stirred tank reactor has been developed to directly measure aqueous reaction rates in the field. Dye and tracer experiments indicate the reactor is well-mixed. Rates of Fe2+ oxidation at untreated and passively treated coal mine drainage sites in Pennsylvania were measured under ambient conditions and with the addition of either O2 gas or NaOH solutions. Rates at 5 sites ranged from below the detection limit for this technique (approximately 10−9 mol L−1 s−1) to 3.27±0.01×10−6 mol L−1 s−1. Uncertainties in rates ranged from 70% near the lower limit of measurement to as little as 1% at higher rates of reaction. Multiple linear regressions showed no universal correlations of rates to Fe2+, dissolved O2, and pH (Thiobacillus populations were not measured), although data for two more acidic sites were found to fit well for the model log rate=log K+a log [Fe2+]+b log [OH−]+c log [O2]. Field rates of Fe oxidation from this and other studies vary by 4 orders of magnitude. A model using the ambient field rate of Fe oxidation from this study successfully reproduced independently-measured Fe2+ concentrations observed in a passive wetland treatment facility.  相似文献   

11.
We studied the role of microbial photosynthesis in the oxidation of Fe(II) to Fe(III) in a high Fe(II) and high Mn(II) hot spring devoid of sulfide and atmospheric oxygen in the source waters. In situ light and dark microelectrode measurements of Fe(II), Mn(II) and O2 were made in the microbial mat consisting of cyanobacteria and anoxygenic photosynthetic Chloroflexus sp. We show that Fe(II) oxidation occurred when the mat was exposed to varying intensities of sunlight but not near infrared light. We did not observe any Mn(II) oxidation under any light or dark condition over the pH range 5-7. We observed the impact of oxygenic photosynthesis on Fe(II) oxidation, distinct from the influence of atmospheric O2 and anoxygenic photosynthesis. In situ Fe(II) oxidation rates in the mats and cell suspensions exposed to light are consistent with abiotic oxidation by O2. The oxidation of Fe(II) to form primary Fe(III) phases contributed to banded iron-formations (BIFs) during the Precambrian. Both oxygenic photosynthesis, which produces O2 as an oxidizing waste product, and anoxygenic photosynthesis in which Fe(II) is used to fix CO2 have been proposed as Fe(II) oxidation mechanisms. Although we do not know the specific mechanisms responsible for all Precambrian Fe(II) oxidation, we assessed the relative importance of both mechanisms in this modern hot spring environment. In this environment, cyanobacterial oxygen production accounted for all the observed Fe(II) oxidation. The rate data indicate that a modest population of cyanobacteria could have mediated sufficient Fe(II) oxidation for some BIFs.  相似文献   

12.
《Geochimica et cosmochimica acta》1999,63(19-20):3171-3182
The oxidation rate of pyrite at pH 7, 25°C and at constant partial pressure of oxygen (0.21 and 0.177 atm) was measured in the presence of the Fe(III)-chelators NTA, oxalate, leucine, EDTA, citrate, IDA and the Fe(III)-reductant ascorbic acid. With the exception of leucine and EDTA, non-reducing Fe(III)-chelators increased the oxidation rate relative to the reference state of formation of the Fe(OH)2+ complex at pH 7. The rate increase was proportional to the logarithm of the conditional stability constant of the ligands for the complexation of Fe3+. No effect on the oxidation rate was observed in the presence of EDTA, which shifted the redox potential of the redox couple Fe2+/Fe3+ to a value below that in the absence of any ligand at pH 7. Ascorbic acid decreased the pyrite oxidation rate by a factor of 5 at ascorbic acid concentrations between 10−4 and 10−2 mol L−1. Comparison of the rate constants for the oxidation of ascorbic acid by surface bound Fe(III) in the absence and presence of pyrite shows that the pyrite surface accelerates this reaction by a factor of 10. The oxidation of both pyrite and ascorbic acid is of fractional order with respect to ascorbic acid (HAsc): rpy=0.55 c(HAsc)−0.35 rHAsc=3.6 c(HAsc)0.59. Both the results from experiments with Fe(III)-chelating ligands and the Fe(III)-reductant, suggest a very efficient interference in the electron cycling between Fe(II) and Fe(III) at the pyrite surface. The interference seems to be mainly related to the reductive side of the iron cycling. It is therefore concluded that the electron transfer between ferric iron and pyritic sulfur limits the pyrite oxidation rate at pH 7.  相似文献   

13.
Neutrophilic iron oxidizing bacteria (FeOB) must actively compete with rapid abiotic processes governing Fe(II) oxidation and as a result have adapted to primarily inhabit low-O2 environments where they can more successfully compete with abiotic Fe(II) oxidation. The spatial distribution of these microorganisms can be observed through the chemical gradients they affect, as measured using in situ voltammetric analysis for dissolved Fe(II), Fe(III), O2, and FeS(aq). Field and laboratory determination of the chemical environments inhabited by the FeOB were coupled with detailed kinetic competition studies for abiotic and biotic oxidation processes using a pure culture of FeOB to quantify the geochemical niche these organisms inhabit. In gradient culture tubes, the maximum oxygen levels, which were associated with growth bands of Sideroxydans lithotrophicus (ES-1, a novel FeOB), were 15-50 μM. Kinetic measurements made on S. lithotrophicus compared biotic/abiotic (killed control) Fe oxidation rates. The biotic rate can be a significant and measurable fraction of the total Fe oxidation rate below O2 concentrations of approximately 50 μM, but biotic Fe(II) oxidation (via the biotic/abiotic rate comparison) becomes difficult to detect at higher O2 levels. These results are further supported by observations of conditions supporting FeOB communities in field settings. Variablity in cell densities and cellular activity as well as variations in hydrous ferrous oxide mineral quantities significantly affect the laboratory kinetic rates. The microbial habitat (or geochemical niche) where FeOB are active is thus largely controlled by the competition between abiotic and biotic kinetics, which are dependent on Fe(II) concentration, PO2, temperature and pH in addition to the surface area of hydrous ferric oxide minerals and the cell density/activity of FeOB. Additional field and lab culture observations suggest a potentially important role for the iron-sulfide aqueous molecular cluster, FeS(aq), in the overall cycling of iron associated with the environments these microorganisms inhabit.  相似文献   

14.
Arsenopyrite (FeAsS) and enargite (Cu3AsS4) fractured in a nitrogen atmosphere were characterised after acidic (pH 1.8), oxidative dissolution in both the presence and absence of the acidophilic microorganism Leptospirillum ferrooxidans. Dissolution was monitored through analysis of the coexisting aqueous solution using inductively coupled plasma atomic emission spectroscopy and coupled ion chromatography-inductively coupled plasma mass spectrometry, and chemical changes at the mineral surface observed using X-ray photoelectron spectroscopy and environmental scanning electron microscopy (ESEM). Biologically mediated oxidation of arsenopyrite and enargite (2.5 g in 25 ml) was seen to proceed to a greater extent than abiotic oxidation, although arsenopyrite oxidation was significantly greater than enargite oxidation. These dissolution reactions were associated with the release of ∼917 and ∼180 ppm of arsenic into solution. The formation of Fe(III)-oxyhydroxides, ferric sulphate and arsenate was observed for arsenopyrite, thiosulphate and an unknown arsenic oxide for enargite. ESEM revealed an extensive coating of an extracellular polymeric substance associated with the L. ferrooxidans cells on the arsenopyrite surface and bacterial leach pits suggest a direct biological oxidation mechanism, although a combination of indirect and direct bioleaching cannot be ruled out. Although the relative oxidation rates of enargite were greater in the presence of L. ferrooxidans, cells were not in contact with the surface suggesting an indirect biological oxidation mechanism. Cells of L. ferrooxidans appear able to withstand several hundreds of ppm of As(III) and As(V).  相似文献   

15.
《Applied Geochemistry》2002,17(4):431-443
A steady state geochemical model has been developed to assist in understanding surface-catalysed oxidation of aqueous Fe(II) by O2(aq), which occurs rapidly at circumneutral pH. The model has been applied to assess the possible abiotic removal of Fe(II)(aq) from alkaline ferruginous mine water discharges using engineered reactors with high specific-surface area filter media. The model includes solution and surface speciation equilibrium, oxidation kinetics of dissolved and adsorbed Fe(II) species and mass transfer of O2(g). Limited field data for such treatment of a mine water discharge were available for model development and assessment of possible parameter values. Model results indicate that an adsorption capacity between 10−6 and 10−5 mol l−1 is sufficient for complete removal, by oxidation, of the Fe(II)(aq) load at the discharge. This capacity corresponds approximately to that afforded by surface precipitation of Fe(III) oxide onto plastic trickling filter media typically used for biological treatment of wastewater. Extrapolated literature values for microbial oxidation of Fe(II)(aq) by neutrophilic microbial populations to the simulated reactor conditions suggested that the microbially-mediated rate may be several orders-of-magnitude slower than the surface-catalysed oxidation. Application of the model across a range of mine water discharge qualities shows that high Fe(II)(aq) loadings can be removed if the discharge is sufficiently alkaline. Additional reactor simulations indicate that reactor efficiency decreases dramatically with pH in the near acid region, coinciding with the adsorption edge for Fe2+ on Fe oxyhydroxide. Alkaline discharges thus buffer pH within the range where Fe(II)(aq) adsorbs onto the accreting Fe hydroxide mineral surface, and undergoes rapid catalytic oxidation. The results suggest that the proposed treatment technology may be appropriate for highly ferruginous alkaline discharges, typically associated with abandoned deep coal mines.  相似文献   

16.
The kinetics of Mn(II) oxidation by the bacterium Leptothrix discophora SS1 was investigated in this research. Cells were grown in a minimal mineral salts medium in which chemical speciation was well defined. Mn(II) oxidation was observed in a bioreactor under controlled conditions with pH, O2, and temperature regulation. Mn(II) oxidation experiments were performed at cell concentrations between 24 mg/L and 35 mg/L, over a pH range from 6 to 8.5, between temperatures of 10°C and 40°C, over a dissolved oxygen range of 0 to 8.05 mg/L, and with L. discophora SS1 cells that were grown in the presence of Cu concentrations ranging from zero to 0.1 μM. Mn(II) oxidation rates were determined when the cultures grew to stationary phase and were found to be directly proportional to O2 and cell concentrations over the ranges investigated. The optimum pH for Mn(II) oxidation was approximately 7.5, and the optimum temperature was 30°C. A Cu level as low as 0.02 μM was found to inhibit the growth rate and yield of L. discophora SS1 observed in shake flasks, while Cu levels between 0.02 and 0.1 μM stimulated the Mn(II) oxidation rate observed in bioreactors. An overall rate law for Mn(II) oxidation by L. discophora as a function of pH, temperature, dissolved oxygen concentration (D.O.), and Cu concentration is proposed. At circumneutral pH, the rate of biologically mediated Mn(II) oxidation is likely to exceed homogeneous abiotic Mn(II) oxidation at relatively low (≈μg/L) concentrations of Mn oxidizing bacteria.  相似文献   

17.
The mechanism of pyrite oxidation in carbonate-containing alkaline solutions at 80 °C was investigated with the help of rate experiments, thermodynamic modeling and diffuse reflectance infrared spectroscopy (DRIFTS). Pyrite oxidation rate increased with pH and was enhanced by addition of bicarbonate/carbonate ions. The carbonate effect was found to be limited to moderately alkaline conditions (pH 8-11). Metastable Eh-pH diagrams, at 25 °C, indicate that soluble iron-carbonate complexes (FeHCO3−, FeCO30, Fe(CO3)(OH)− and FeCO32−) may coexist with pyrite in the pH range of 6-12.5. Above pH 11 and 13, the Fe(II) and Fe(III) hydroxocomplexes, respectively, become stable, even in the presence of carbonate/bicarbonate ions. Surface-bound carbonate complexes on iron were also identified with DRIFTS as products of pyrite oxidation in addition to iron oxyhydroxides and soluble sulfate species. The conditions under which thermodynamic and DRIFTS analyses indicate the presence of carbonate compounds also correspond to those in which the fastest rate of pyrite oxidation in carbonate solutions was observed. Following the Singer-Stumm model for pyrite oxidation in acidic solutions, it is assumed that Fe(III) is the preferred pyrite oxidant under alkaline conditions. We propose that carbonate ions facilitate the electron transfer from soluble iron(II)-carbonate to O2, increase the iron solubility, and provide buffered, favorable alkaline conditions at the reaction front, which in turn favors the overall kinetics of pyrite oxidation. Therefore, the electron transfer from sulfur atoms to O2 is facilitated by the formation of the cycle of Fe(II)-pyrite/Fe(III)-carbonate redox couple at the pyrite surface.  相似文献   

18.
The effect of ionic interactions of the major components of natural waters on the oxidation of Cu(I) and Fe(II) has been examined. The various ion pairs of these metals have been shown to have different rates of oxidation. For Fe(II), the chloride and sulfate ion pairs are not easily oxidized. The measured decrease in the rate constant at a fixed pH in chloride and sulfate solutions agrees very well with the values predicted. The effect of pH (6 to 8) on the oxidation of Fe(II) in water and seawater have been shown to follow the rate equation
-d in [Fe(II)]/dt = k1β1αFe/[H+] + k2β2αFe/[H+]2
where k1 and k2 are the pseudo first order rate constants, β1 and β2 are the hydrolysis constants for Fe(OH)+ and Fe(OH)0. The value of αFE is the fraction of free Fe2+. The value of k1 (2.0 ±0.5 min?1) in water and seawater are similar within experimental error. The value of k2 (1.2 × 105 min?1) in seawater is 28% of its value in water in reasonable agreement with predictions using an ion pairing model.For the oxidation of Cu(I) a rate equation of the form
?d ln [Cu(I)]/dt = k0αCu+ k1β1αCu[Cl]
was found where k0 (14.1 sec?1) and k1 (3.9 sec?1) are the pseudo first order rate constants for the oxidation of Cu+ and CuCl0, β1 is the formation constant for CuCl0 and αCu is the fraction of free Cu+. Thus, unlike the results for Fe(II), Cu(I) chloride complexes have measurable rates of oxidation.  相似文献   

19.
The subsurface behaviour of 99Tc, a contaminant resulting from nuclear fuels reprocessing, is dependent on its valence (e.g., IV or VII). Abiotic reduction of soluble Tc(VII) by Fe(II)(aq) in pH 6-8 solutions was investigated under strictly anoxic conditions using an oxygen trap (<7.5 × 10−9 atm O2). The reduction kinetics were strongly pH dependent. Complete and rapid reduction of Tc(VII) to a precipitated Fe/Tc(IV) form was observed when 11 μmol/L of Tc(VII) was reacted with 0.4 mmol/L Fe(II) at pH 7.0 and 8.0, while no significant reduction was observed over 1 month at pH 6.0. Experiments conducted at pH 7.0 with Fe(II)(aq) = 0.05-0.8 mmol/L further revealed that Tc(VII) reduction was a combination of homogeneous and heterogeneous reaction. Heterogeneous reduction predominated after approximately 0.01 mmol/L of Fe(II) was oxidized. The heterogeneous reaction was more rapid, and was catalyzed by Fe(II) that adsorbed to the Fe/Tc(IV) redox product. Wet chemical and Fe-X-ray absorption near edge spectroscopy measurements (XANES) showed that Fe(II) and Fe(III) were present in the Fe/Tc(IV) redox products after reaction termination. 57Fe-Mössbauer, extended X-ray adsorption fine structure (EXAFS), and transmission electron microscopy (TEM) measurements revealed that the Fe/Tc(IV) solid phase was poorly ordered and dominated by Fe(II)-containing ferrihydrite with minor magnetite. Tc(IV) exhibited homogeneous spatial distribution within the precipitates. According to Tc-EXAFS measurements and structural modeling, its molecular environment was consistent with an octahedral Tc(IV) dimer bound in bidentate edge-sharing mode to octahedral Fe(III) associated with surface or vacancy sites in ferrihydrite. The precipitate maintained Tc(IV)aq concentrations that were slightly below those in equilibrium with amorphous Tc(IV)O2·nH2O(s). The oxidation rate of sorbed Tc(IV) in the Fe/Tc precipitate was considerably slower than Tc(IV)O2·nH2O(s) as a result of its intraparticle/intragrain residence. Precipitates of this nature may form in anoxic sediments or groundwaters, and the intraparticle residence of sorbed/precipitated Tc(IV) may limit 99Tc remobilization upon the return of oxidizing conditions.  相似文献   

20.
Discharge of Fe(II)-rich groundwaters into surface-waters results in the accumulation of Fe(III)-minerals in salinized sand-bed waterways of the Hunter Valley, Australia. The objective of this study was to characterise the mineralogy, micromorphology and pore-water geochemistry of these Fe(III) accumulations. Pore-waters had a circumneutral pH (6.2–7.2), were sub-oxic to oxic (Eh 59–453 mV), and had dissolved Fe(II) concentrations up to 81.6 mg L−1. X-ray diffraction (XRD) on natural and acid-ammonium-oxalate (AAO) extracted samples indicated a dominance of 2-line ferrihydrite in most samples, with lesser amounts of goethite, lepidocrocite, quartz, and alumino-silicate clays. The majority of Fe in the samples was bound in the AAO extractable fraction (FeOx) relative to the Na-dithionite extractable fraction (FeDi), with generally high FeOx:FeDi ratios (0.52–0.92). The presence of nano-crystalline 2-line ferrihydrite (Fe5HO3·4H2O) with lesser amounts of goethite (α-FeOOH) was confirmed by scanning electron microscopy (SEM) coupled with energy dispersive X-ray analysis (EDX), and transmission electron microscopy (TEM) coupled with selected area electron diffraction (SAED). In addition, it was found that lepidocrocite (γ-FeOOH), which occurred as nanoparticles as little as ∼5 lattice spacings thick perpendicular to the (0 2 0) lattice plane, was also present in the studied Fe(III) deposits. Overall, the results highlight the complex variability in the crystallinity and particle-size of Fe(III)-minerals which form via oxidation of Fe(II)-rich groundwaters in sand-bed streams. This variability may be attributed to: (1) divergent precipitation conditions influencing the Fe(II) oxidation rate and the associated supply and hydrolysis of the Fe(III) ion, (2) the effect of interfering compounds, and (3) the influence of bacteria, especially Leptothrix ochracea.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号