共查询到20条相似文献，搜索用时 31 毫秒
1.
2.
The acoustic properties of seafloor sediments are of great importance in geoacoustic modeling, detecting, and oceanic engineering. The methods based on the first arrival cycle are investigated to calculate sound speed and attenuation of sediment more precisely in in situ measurements. The comparison of different data analysis methods based on the first arrival cycle approach for in situ measurement results in the following conclusions: (1) the calculated methods can help find the effective cycles and reduce the errors in calculating sound speed and attenuation; (2) using this approach, the point judgment method-based data analysis has the same effectiveness as the cross-correlation method-based data analysis in calculating group sound speed and has the same effectiveness in calculating attenuation in the time domain as the spectrum analysis method-based data analysis has in calculating attenuation in frequency domain; and (3) measurement in water can help not only calibrate the transmitting distance but also can calculate the time delay for the sound speed and the attenuation loss in the transmitting process. Finally, theoretical calculation was used to calculate the measured results, indicating a good agreement, which supports that first arrival cycle-based calculated methods can be used to analyze the measured data and the effective density fluid model can be used to analyze more acoustic properties and invert several physical properties in this experiment. 相似文献
3.
Comparison of sound speed and attenuation measured in a sandy sediment to predictions based on the Biot theory of porous media 总被引：2，自引：0，他引：2
Williams K.L. Jackson D.R. Thorsos E.I. Dajun Tang Schock S.G. 《Oceanic Engineering, IEEE Journal of》2002,27(3):413-428
During the sediment acoustics experiment in 1999 (SAX99), several researchers measured sound speed and attenuation. Together, the measurements span the frequency range of about 125 Hz-400 kHz. The data are unique both for the frequency range spanned at a common location, and for the extensive environmental characterization that was carried out as part of SAX99. Environmental measurements were sufficient to determine or bound the values of almost all the sediment and pore water physical property input parameters of the Biot poroelastic model for sediment. However, the measurement uncertainties for some of the parameters result in significant uncertainties for Biot-model predictions. Here, measured sound-speed and attenuation results are compared to the frequency dependence predicted by Biot theory and a simpler "effective density" fluid model derived from Biot theory. Model/data comparisons are shown where the uncertainty in Biot predictions due to the measurement uncertainties for values of each input parameter are quantified. A final set of parameter values, for use in other modeling applications e.g., in modeling backscattering (Williams et al., 2002) are given, that optimize the fit of the Biot and effective density fluid models to the sound-speed dispersion and attenuation measured during SAX99. The results indicate that the variation of sound speed with frequency is fairly well modeled by Biot theory but the variation of attenuation with frequency deviates from Biot theory predictions for homogeneous sediment as frequency increases. This deviation may be due to scattering from volume heterogeneity. Another possibility for this deviation is shearing at grain contacts hypothesized by Buckingham; comparisons are also made with this model. 相似文献
4.
Zhaohui Peng Ji-Xun Zhou Dahl P.H. Renhe Zhang 《Oceanic Engineering, IEEE Journal of》2004,29(4):1038-1045
As a part of the Asian Seas International Acoustic Experiment (ASIAEX) in the East China Sea, sound propagation signals from wideband explosive sources were measured using a 32-element vertical line array. Measurements were made as a function of range in two perpendicular tracks. Sea-bed geoacoustic parameters based on a fluid half-space geoacoustic model (sound speed, density, and attenuation) are inverted from the sound propagation in the frequency range 100-500 Hz. The sea-bed sound speed and density were first derived from mode arrival time differences which were obtained using a spatial mode filtering technique. Sea-bed acoustic attenuation was subsequently estimated by comparing measured transmission loss with model results. 相似文献
5.
A remote sediment classification technique based on attenuation measurements from Chirp sub-bottom profiler data is described. This differs from previously published work in that attenuation measurements are obtained for each stratigraphic unit within a complex, thinly interbedded sedimentary sequence. Compressional wave attenuation measurements are obtained for a wide variety of lithologies, including muds, silts, sands, clayey sands, silty clays and gravel lags, with grain sizes ranging from 8 Phi to -4 Phi. In addition, attenuation measurements from sub-bottom profiler data were calibrated against laboratory acoustic measurements of vibracores and seabed samples from corresponding geographic locations, under simulated in-situ conditions using a Pulse Tube method. We adapt an instantaneous frequency matching method using a causal attenuation filter to model the decay of the Chirp transmitted waveform. From this modelling, a relationship between t* (a causal attenuation operator) and change in instantaneous frequency is established. The Hilbert transform is used to extract instantaneous frequency information from Chirp seismic, which is used to derive attenuation information for selected individual stratigraphic layers imaged by the sub-bottom profiler. This paper draws attention to the limitations in comparing attenuation measurements derived from Chirp sub-bottom profiler data against previously published literature on experimental attenuation measurements, which are limited by the wide variance of these data, and the difficulty in finding a meaningful best fit to these data. This demonstrates the importance of calibrating remote sediment classification observations using complimentary acoustic analysis of seabed samples to generate a site-specific geoacoustic database. A positive correlation between laboratory and sub-bottom profiler attenuation measurements was obtained, with a correlation coefficient of 0.885. Poorly sorted gravels with a mixed lithic and biogenic pebble component are characterised by very high attenuation with values of Q from 4 to 19. These sediments are considerably coarser-grained than those typically described in previously published experimental studies. 相似文献
6.
This paper describes results from an experiment carried out to investigate geoacoustic inversion with a bottom-moored hydrophone array located in the shallow waters of the Timor Sea off the northern coast of Australia. The array consisted of two arms in a V shape, horizontally moored at a site that was essentially flat over a large area. Hydrophone positions were estimated using an array element localization (AEL) technique that established relative uncertainties of less than 1 m on the seafloor. The data used for geoacoustic inversion were from experiments with continuous wave (CW) tones in the 80- to 195-Hz band transmitted from a towed projector. A hybrid search algorithm determined the set of geoacoustic model parameters that maximized the Bartlett fit (averaged coherently spatially at each tone and incoherently over frequency) between the measured and modeled data at the array. Due to the long range experimental geometry, the inversion was sensitive to attenuation in the sediment. The inverted geoacoustic profile performed well in a simple test for localizing the sound source at other sites in the vicinity of the array. Range-depth localization performance for the horizontal array was comparable to that for an equivalent vertical array. 相似文献
7.
Heaney K.D. Sternlicht D.D. Teranishi A.M. Castile B. Hamilton M. 《Oceanic Engineering, IEEE Journal of》2004,29(1):100-109
A survey of received acoustic energy levels from a seismic profiler were performed in Long Beach Harbor, CA, for compliance with the Marine Mammal Protection Act (MMPA). In addition to direct acoustic measurements, a rapid geoacoustic inversion algorithm was applied to the data to estimate the sediment properties acoustically. This inversion algorithm has matching criteria based on time spread, range-frequency interference patterns, and the range dependence of transmission loss. Self-consistency was checked by comparing acoustic measurements with predictions based on the inversion. With an estimated geoacoustic profile, predictions of received levels as a function of position in the range-dependent environment of Long Beach Harbor were then performed. 相似文献
8.
多频海底声学原位测试系统研制和试用 总被引：9，自引：2，他引：9
海底沉积物的声学特性(最重要的是声速和声衰减)以及它们与物理(包括土力学)特性之间的关系是沉积物声学中两个重要的研究项目.介绍了新研制的实时监控多频海底声学原位测试系统.该系统可测量浅表层沉积物的声速.探测频率为8,10,12,15 kHz,可根据实际情况选择发射波形、接收增益和采样长度,采样率为0.5~2.0 MHz,工作水深为300 m.系统具有倾斜传感器、8通道扩充等功能.用该系统在杭州湾测得了四种频率的沉积物原位声速. 相似文献
9.
Hamilton-type geoacoustic models were developed for Area Foxtrot, a shallow water test bed south of Long Island, for emerging active sonar systems where the surface sediment type is highly spatially variable. Reverberation levels (RL) were modeled using the finite-element parabolic equation (FEPE) propagation model to augment the generic sonar model (GSM) propagation model because the bottom loss model in GSM did not estimate transmission loss (TL) accurately in shallow water. FEPE estimates reveal that there is a greater than 15 dB difference between TL for sand and that for silt-day sediments in Area Foxtrot. The comparison between modeled RL and measured RL (from a 1991 active sonar exercise) enabled bottom scattering strength kernels to be developed for Area Foxtrot. Bottom scattering strength was found to be a function of sediment type. Hard sand sediment has a bottom scattering strength which obeys Lambert's law (sin2 &thetas;) while that of silt-clay sediment is consistent with sub-bottom volume scattering (sine). The RLs in Area Foxtrot are azimuth-dependent and are a function of TL and bottom scattering strength (and hence bottom sediment type). Sonar beams steered towards the hard sand show higher RLs than for silt-clay, and knowledge of the sediment type and its spatial variation must be known to model RL accurately. A method to determine sediment type using measured RLs and RL slopes is given 相似文献
10.
Sora Kim Daechoul Kim Jooyoung Hahn Woo-Hun Ryang 《Marine Georesources & Geotechnology》2018,36(3):280-287
Laboratory measurements of sound velocity in unconsolidated marine sediment were performed to establish specific correction curves between temperature and sound velocity. Cores from the Hupo Basin and the southern sea of Geumo Island were cooled and sound velocity was measured while gradually increasing temperature (from 3 to 30°C). Sediment textural and physical properties (porosity, water content, and bulk density) were measured at the same depth. Sound velocity increases with temperature for clay, mud, silt, and sand sediment, resulting in values of approximately 2.65, 2.72, 2.78, and 3.10?m/s/°C, respectively. These results are similar to those of previous studies, and differences are likely due to density, porosity, and clay contents of the sediment. Using these results, we present correction curves for sound velocity temperature dependence for each sediment texture, which can be used to correct from laboratory to in situ values to develop accurate geoacoustic model. 相似文献
11.
为准确建立海底地声模型,本文探讨地声模型的基本组成和基本结构。通过样品实验室测量,分析南海海底表层沉积物的密度、孔隙度与声速随着埋深变化的关系,得出海底实际存在的低声速表面–声速缓慢变化类型、低声速表面–声速增大类型、高声速表面–声速缓慢变化类型和高声速表面–声速增大类型4种典型地声结构;对比钻探测量,分析黄海海底沉积物的密度、孔隙度与声速随埋深变化关系,得出海底地声模型分层特征与地声结构组合特征。研究表明,地声模型可以归结为4种基本地声结构的组合,通过与底层海水声速、同层内声速剖面以及与上层海底沉积物下表面声速的比较,可以建立各种海底地声模型;基于实验室测量法建立的地声模型可以作为参考地声模型,但需要考虑实际海底温度和压力梯度以及海底沉积物的频散特性等,借助于声速比校正法和频散性理论模型进行计算及修正。 相似文献
12.
Ji-Xun Zhou Xue-Zhen Zhang Rogers P.H. Simmen J.A. Dahl P.H. Guoliang Jin Zhaohui Peng 《Oceanic Engineering, IEEE Journal of》2004,29(4):988-999
Optimal array-processing techniques in the ocean often require knowledge of the spatial coherence of the reverberation. A mathematical model is derived for the reverberation vertical coherence (RVC) in shallow water (SW). A method for analysis of RVC data is introduced. Measured reverberation cross-correlation coefficients as a function of time and frequency, obtained during the Asian Seas International Acoustic Experiment (ASIAEX) in the East China Sea, are reported. SW reverberation from a single shot provides a continuous spatial sampling of the surrounding sound field up to several tens of kilometers and holds valuable information on the geoacoustic properties of the sea floor over this distance. SW reverberation data can, therefore, be used as the basis for a quick and inexpensive method for geoacoustic inversion and has the obvious advantage that acquiring the data in situ requires only a single platform. This paper considers the use of the vertical coherence of the reverberation as the starting point for such an inversion. Sound speed and attenuation in the sea bottom at the ASIAEX site are obtained over a frequency range of 100-1500 Hz by finding values that provide the best match between the measured and predicted RVC. 相似文献
13.
Estimates of geoacoustic model parameters from inversions of horizontal and vertical line array data
This paper describes results from geoacoustic inversion of low-frequency acoustic data recorded at a receiving array divided into two sections, a sparse bottom laid horizontal array (HLA) and a vertical array (VLA) deployed in shallow water. The data are from an experiment conducted by the Norwegian Defence Research Establishment (FFI) in the Barents Sea, using broadband explosives (shot) sources. A two-layer range-independent geoacoustic model, consistent with seismic profiles from the area, described the environment. Inversion for geoacoustic model parameters was carried out using a fast implementation of the hybrid adaptive simplex simulated annealing (ASSA) inversion algorithm, with replica fields computed by the ORCA normal mode code. Low-frequency (40-128 Hz) data from six shot sources at ranges 3-9 km from the array were considered. Estimates of sediment and substrate p-wave velocities and sediment thickness were found to be consistent between independent inversions of data from the two sections of the array. 相似文献
14.
15.
Reverberation measurements made by the SACLANT Undersea Research Centre at three shallow-water sites (130-190-m depth) are compared with each other and with estimates from the DREA normal-mode reverberation model OGOPOGO. The experiments over silt-clay and sand seabeds were conducted at slightly bistatic geometries (0.7-6.0-km source-receiver separation), using explosive sources detonated at mid-water depths. The signals were received on hydrophones of either a vertical or horizontal array and analyzed in one-tenth-decade frequency bands from 25 to 1000 Hz. The data are compared with each other to investigate the site differences and frequency dependencies, and with the estimates from the reverberation model OGOPOGO to interpret the data and to obtain a qualitative measure of the scattering. For modeling purposes, geoacoustic models of the seabed were assumed, and the reverberation data were fitted by adjusting the Lambert bottom scattering coefficients. Good model agreement was obtained with both individual hydrophone and data. Though somewhat sensitive to the geoacoustic the Lambert coefficients give a measure of the frequency dependence of the scattering. For the silt-clay bottom, the scattering is weak but is independent of frequency; for the sand bottoms, the scattering is stronger and increases with frequency. These results are compared with estimates from other experiments 相似文献
16.
Fallat M.R. Nielsen P.L. Dosso S.E. Siderius M. 《Oceanic Engineering, IEEE Journal of》2005,30(1):198-206
This paper examines geoacoustic inversion over a range-dependent multiple-layer seabed using a towed acoustic source and towed horizontal array. The approach is based on combining the results of a series of short-range, range-independent inversions to form a range-dependent representation of the environment. The data were collected in the Strait of Sicily during the MAPEX 2000 experiment. Issues such as the resolvability of multilayer structure and the sensitivity of various geoacoustic parameters are investigated by inversion of simulated data and by comparison of the MAPEX 2000 inversion results to a high-resolution seismic profile and to sediment core measurements. It appears that two, and in some cases possibly three, sediment layers can be resolved. 相似文献
17.
Matched-field inversion is used to, estimate geoacoustic properties from data obtained in an experiment with a vertical line array (VLA). The experiment was carried out using broad-band sources (shots) in water depths of about 200 m on the continental shelf off Vancouver Island. The data were processed to obtain spectral components of the field for frequencies near the bubble frequency for the shot. The ocean bottom in this region consists of a layer of mainly sandy sediments (about 100 m thick) overlying older consolidated material. Consequently, the inversion was designed to estimate the parameters of a two-layer elastic sediment model. In the inversion, an adaptive global search algorithm was used to investigate the multidimensional space of geoacoustic models in order to determine the set of values corresponding to the best replica field. Convergence is driven by adaptively guiding the search to regions of the parameter space associated with above-average values of the matched field correlation between the measured and replica fields. The geoacoustic profile estimated by the inversion consisted of a 125-m layer with compressional speed ~1700 m/s and shear speed ~400 m/s, overlying a layer with compressional speed ~1900 m/s. This model is consistent with the results from conventional seismic experiments carried out in the same region 相似文献
18.
Robb G.B.N. Best A.I. Dix J.K. White P.R. Leighton T.G. Bull J.M. Harris A. 《Oceanic Engineering, IEEE Journal of》2007,32(2):484-496
Geoacoustic inversion requires a generic knowledge of the frequency dependence of compressional wave properties in marine sediments, the nature of which is still under debate. The use of in situ probes to measure sediment acoustic properties introduces a number of experimental difficulties that must be overcome. To this end, a series of well-constrained in situ acoustic transmission experiments were undertaken on intertidal sediments using a purpose-built in situ device, the Sediment Probing Acoustic Detection Equipment (SPADE). Compressional wave speed and attenuation coefficient were measured from 16 to 100 kHz in medium to fine sands and coarse to medium silts. Spreading losses, which were adjusted for sediment type, were incorporated into the data processing, as were a thorough error analysis and an examination of the repeatability of both the acoustic wave emitted by the source and the coupling between probes and sediment. Over the experimental frequency range and source-to-receiver (S-R) separations of 0.99-8.1 m, resulting speeds are accurate to between 1.1% and 4.5% in sands and less than 1.9% in silts, while attenuation coefficients are accurate to between 1 and 7 dBm in both sands and silts. Preliminary results indicate no speed dispersion and an attenuation coefficient that is proportional to frequency. 相似文献
19.
Lei Sun Xiangmei Meng Guanbao Li Guangming Kan Baohua Liu 《Marine Georesources & Geotechnology》2020,38(5):595-603
AbstractThe high-frequency acoustic properties of seafloor sediments are very significant in seafloor study and underwater acoustic study field. In order to measure the sound speed and the attenuation for the small-scale sediment cores more accurately, this study developed a water coupled acoustic laboratory measurement system based on Richardson-Briggs technique. This method used the correlation comparison of waveforms received in sediment core and in identical reference tubes filled with water to measure sound speed and attenuation. The sound speed and attenuation of a clayey silt sediment sample were measured using the water coupled acoustic laboratory measurement system. This frequency dependence of the sound speed and attenuation showed that the clayey silt sediment has a weak positive sound speed dispersion, while the attenuation increases with a strong positive gradient within the measurement frequency range. This study also noted that the measured sound speed ratio match well with the empirical equations from literature. The measured attenuation factor data can fall in the Hamilton’s empirical prediction range. 相似文献
20.
A method for estimating the physical and acoustic properties of the sea bed using chirp sonar data 总被引：2，自引：0，他引：2
This paper proposes a method, based on the Biot model, for estimating the physical and acoustic properties of surficial ocean sediments from normal incidence reflection data acquired by a chirp sonar. The inversion method estimates sediment porosity from reflection coefficient measurements and, using the estimated porosity and the measured change in fast wave attenuation with frequency, estimates the permeability of the top sediment layer. The spectral ratio of echoes from the interface at the base of the upper sediment layer and from the sediment-water interface provides a measure of the change in attenuation with frequency. Given the porosity and permeability estimates, the Kozeny-Carman equation provides the mean grain size and the inversion method yields the acoustic properties of top sediment layer. The inversion technique is tested using chirp sonar data collected at the 1999 Sediment Acoustics Experiment (SAX-99) site. Remote estimates of porosity, grain size, and permeability agree with direct measurements of those properties. 相似文献