共查询到19条相似文献，搜索用时 703 毫秒
1.
2.
综述了由最初的普通钢筋混凝土抗拔（浮）桩发展到预应力抗拔（浮）桩的历程；总结了对于抗拔桩性能研究的3种方法：现场试验、模型试验和理论分析法。在此基础上为了降低成本，方便施工，环保高效，提出了一种新型的预应力抗拔（浮）桩，即部分粘接预应力抗拔（浮）桩，这将是预应力抗拔（浮）桩一个有意义的发展方向。 相似文献
3.
通过颗粒流数值模拟,从桩端阻力随上拔位移的发展与桩端周围土体颗粒位移表现等角度,研究了扩底抗拔桩端阻力的群桩效应问题。研究比较了单桩（墩）与群桩（墩）的抗拔性状以及不同墩距下中心墩与边墩阻力随上拔位移发展的情况。研究表明,在归一化上拔量 0.1时,单桩（墩）与群桩（墩）的上拔特性无明显差别;此后,随着上拔位移的发展,单桩（墩）的上拔端阻力要大于群桩中的桩（墩）的端阻力,桩（墩）周围土体颗粒的相互影响开始显现。在归一化上拔量 0.5的情况下,群桩（墩）中中心桩（墩）的端阻力要略大于边桩（墩）。在归一化上拔量 0.5的情况下,群桩中边桩的桩端阻力较中心桩的要大,而群墩中边墩的墩端阻力较中心墩要小,体现了桩身侧限对抗拔桩群中端阻力发挥的影响。随着墩距的增大,在较大的位移量以后群墩才与单墩的受力有显著差别。 相似文献
4.
五星形桩是一种新型的截面异形桩,是在圆桩基础上向内切割5个圆弧,形成截面类似五星形的一种桩型。利用自主研发的多功能桩基模型试验加载系统,砂雨法成桩,进行了4根五星形与圆形桩（周长最大化五星形桩F1、周长面积比最大化五星形桩F2、与F2同截面周长的圆桩C1、与F2同截面面积的圆桩C2）抗拔承载特性对比模型试验研究。试验结果表明:（1）五星形桩F1与F2的极限抗拔力基本相同,大圆桩C1最大,小圆桩C2最小。（2）大圆桩C1的极限抗拔力是F2的1.73倍,说明五星形截面形式对抗拔侧摩阻力产生了较明显的弱化。（3）小圆桩C2的侧表面积是F2的0.66倍,但其极限抗拔力是F2的0.8倍,这进一步说明五星形截面形式对抗拔侧摩阻力有一定程度的弱化。但F2的极限抗拔力是C2的1.25倍,可见桩的截面形式由圆形转变为五星形可一定程度地提高抗拔承载能力。（4）抗拔侧摩阻力与上拔位移呈双曲线分布,仅需较小位移就可达到极值。 相似文献
5.
为了解决无法采用已注浆锚索进行抗拔试验问题,基于界面脱黏剪切模型,利用荷载传递和弹性变形理论,考虑锚索锚固段与自由段长度比Lb /La的影响,建立了采用自由段已注浆锚索抗拔试验结果评价锚索抗拔性能的方法。结果表明：自由段注浆对锚索抗拔力有较大幅度的提高,尤其是当界面剪切阶段由弹性向脱黏过渡时,提高比例快速增加,并在脱黏后逐渐趋于稳定。其次,锚索自由段与锚固段交界面处剪切位移和轴力最大,并向两端逐渐降低。随着拉拔力的提高,界面剪切位移和轴力都不断增大,同时向锚索两端的衰减速度也加快。此外,弹性阶段时剪应力曲线为山峰型,而脱黏阶段为马鞍型,并随抗拔力的提高,马鞍开口逐渐扩大。最后,锚固段与自由段长度比Lb /La对锚索极限抗拔力的影响较小,其极限抗拔力折减系数?Q取值介于0.81～0.83之间,且Lb /La =2.5时,?Q计算值仅比实测结果小6.02%,验证了本文方法的可行性。 相似文献
6.
7.
DX桩抗拔承载机理及设计计算方法研究 总被引：12，自引：0，他引：12
DX桩（挤扩灌注桩）具有良好的抗拔特性和广阔的工程应用前景。对DX桩与普通桩的抗拔承载特性进行了对比分析,探讨了DX桩的抗拔破坏模式,分析了DX桩的抗拔荷载传递机理及其主桩桩侧与支盘抗拔阻力沿深度的发挥特征。在此基础上,根据DX桩的构造特征,充分考虑主桩桩侧摩阻力和DX桩支盘或3n型分支周围土体摩阻力的影响,建立了极限状态下DX桩抗拔平衡方程,从而导得DX桩抗拔承载力计算公式;对公式中各计算参数的合理选取及相应的试验手段等进行了分析和讨论,给出了DX桩的抗拔设计计算方法与步骤。最后,对影响DX桩抗拔承载力的桩侧土体强度、支盘受荷面与水平面的夹角、支盘数量与间距以及成桩工艺等主要因素进行了定性的分析。 相似文献
8.
9.
提高锚杆锚固力方法研究 总被引：1，自引：0，他引：1
在总结大连地区15项工程76根锚杆抗拔试验时发现锚杆的锚固力是受多种因素影响的,其中主要因素是钻探成孔工艺(影响c,φ值)和锚杆注浆质量(影响k0值).对于风化岩或土层灌浆锚杆建议采用风动成孔;对于中风化或微风化岩层灌浆锚杆建议采用风动成孔并进行清水洗孔;对于锚杆注浆建议采用膨胀砂浆,并建议锚杆抗拔试验同时进行钢筋应力测试. 相似文献
10.
11.
带加强肋土工格栅的极限拉拔阻力分析 总被引：1，自引：0，他引：1
在立体加筋体系研究基础上,提出了带加强肋土工格栅加筋,即通过对普通土工格栅的肋进行加强处理,使其肋具有一定的竖向厚度,构成具有立体加筋效果的带加强肋土工格栅。采用染色砂法,通过带加强肋土工格栅的拉拔试验进行了拉拔力机理分析。在拉拔过程中,加强肋前方土体会首先被挤密加强,成为一个刚性的楔体,然后刚性楔与筋材一起运动成为一个土筋共同体。推导了带加强肋土工格栅加筋土的拉拔阻力模型,分析中将加强肋的侧阻力作用简化为侧向土压力的作用,采用极限平衡理论,通过两侧的主动土压力与被动土压力进行计算。根据所建立的拉拔阻力模型计算出带加强肋土工格栅加筋的极限拉拔阻力,并与试验结果进行了对比,两者基本吻合 相似文献
12.
《Georisk: Assessment and Management of Risk for Engineered Systems and Geohazards》2013,7(3-4):218-228
This paper reports the results of load and resistance factor design (LRFD) calibration for pullout and yield limit states for steel grid reinforced soil walls owing to soil self-weight loading plus permanent uniform surcharge. The calibration method uses bias statistics to account for prediction accuracy of the underlying deterministic models for reinforcement load, pullout capacity and yield strength of the steel grids, and random variability in input parameters. A new revised pullout design model is proposed to improve pullout resistance prediction accuracy and to remove hidden dependency with calculated pullout resistance values. Load and resistance factors are proposed that give a uniform probability of failure of 1% for both pullout and yield limit states. The approach adopted in this paper has application to a wide variety of other reinforced soil wall technologies. 相似文献
13.
J. T. Shahu 《国际地质力学数值与分析法杂志》2008,32(18):2067-2081
In this paper, a rational analysis of pullout resistance of inextensible sheet reinforcement subjected to oblique end force has been presented considering a non‐linear (hyperbolic), elasto‐plastic, normal stress–displacement relationship of the subgrade. Under an oblique pull, high normal stresses develop on stronger subgrades, thus mobilizing high shearing resistance at the reinforcement–soil interface. The higher the bearing resistance of the subgrade, the higher the horizontal component of pullout force and the lower the end displacement of the reinforcement. On the other hand, the end displacement at pullout can become very high for weaker subgrades especially at high values of the angle of obliquity. Also, the pullout capacity under oblique loading for weaker subgrades may approach or even fall below the axial pullout capacity at high values of the angle of obliquity. These adverse pullout responses owing to a low value of bearing resistance of subgrade are magnified when the subgrade stiffness is also small. On weaker subgrades, improvement in angle of interface shear is not advisable as this leads to further reduction in the pullout force and increase in the end displacement. Results are compared with back analysis of published test data on model reinforced soil walls. The comparison suggests that the present model leads to a more rational and better prediction of the pullout failure. Copyright © 2008 John Wiley & Sons, Ltd. 相似文献
14.
With rapid advancements in technology globally, the use of plastics such as polyethylene bags, bottles etc. is also increasing. The disposal of thrown away wastes pose a serious challenge since most of the plastic wastes are non-biodegradable and unfit for incineration as they emit harmful gases. Soil stabilization improves the engineering properties of weak soils by controlled compaction or adding stabilizers like cement, lime etc. but these additives also have become expensive in recent years. This paper presents a detailed study on the behavior and use of waste plastic in soil improvement. Experimental investigation on reinforced plastic soil results showed that, plastic can be used as an effective stabilizer so as to encounter waste disposal problem as well as an economical solution for stabilizing weak soils. Plastic reinforced soil behaves like a fiber reinforced soil. This study involves the investigation of the effect of plastic bottle strips on silty sand for which a series of compaction, direct shear and California bearing ratio (CBR) tests have been performed with varying percentages of plastic strips and also with different aspect ratios in terms of size. The results reflect that there is significant increment in maximum dry unit weight, Shear Strength Parameters and CBR value with plastic reinforcement in soil. The quantum of improvement in the soil properties depends on type of soil, plastic content and size of strip. It is observed from the study that, improvement in engineering properties of silty sand is achieved at 0.4% plastic content with strip size of (15 mm?×?15 mm). 相似文献
15.
网格状带齿加筋是一种新型的土工加筋技术,汲取了传统网格状与条带式带齿加筋的优点,其筋土界面特性是加筋结构设计的基础。利用室内拉拔试验从宏观角度分析筋材与土的界面特性,结合颗粒流程序,筋材用平行黏结模拟,从细观角度分析筋土接触界面的产生和发展演化规律。数值结果表明：齿筋的存在对界面处颗粒的移动及剪切带的宽度影响显著,其破坏模式呈现波浪型,在齿筋附近出现应力集中现象。筋土界面处筋材与土颗粒摩擦、咬合和阻抗作用提供“似黏聚力”是改变网格状带齿加筋体系作用机制的内在原因。研究成果对于明确网格状带齿加筋拉拔的机制及模型的建立都具有意义。 相似文献
16.
土工格栅与土界面作用特性试验研究 总被引：9，自引：4，他引：5
土工格栅与土的界面摩擦特性指标是加筋土工程设计的关键。通过分析土工格栅与土的界面摩擦作用和进行了直剪摩擦试验和拉拔摩擦试验,测试了两种试验条件的界面摩擦特性。在两种试验条件下,土工格栅加筋土复合体的抗剪强度均有界面摩擦角φsq和界面凝聚力csq,且土工格栅与土相对位移量的不同,其复合体的强度机理有区别。在拉拔摩擦试验中,剪应力峰值强度对应的剪切变形值高于直剪摩擦试验中剪应力峰值强度的剪切变形值5～10倍以上。两种试验均有其适用性,而土与土工格栅的相对位移较小时直剪摩擦试验较能反映实际;土与土工格栅相对位移较大时土与格栅双面均发生相对位移,拉拔摩擦试验更为合适。随法向应力的增大,直剪摩擦和拉拔摩擦试验的剪应力峰值以及剪应力峰值对应的位移均提高。直剪摩擦的剪切速度小,剪应力峰值强度高,且达到峰值强度的剪切位移大;增加剪切速度,剪应力峰值强度降低,且对应的位移也减少,其原因是界面上的孔隙水压力消散和筋材的应力松弛。应根据具体工程的需要选择直剪摩擦试验和拉拔摩擦试验确定设计参数。 相似文献
17.
灌浆土钉在边坡加固工程中有着广泛的应用。土钉在不同条件下的抗拔机制仍是进一步研究的课题。通过建立一个三维有限元模型,研究土钉在不同上覆压力和剪胀作用下的土钉抗拔行为。采用摩尔-库仑模型模拟花岗岩土,土与土钉界面采用“接触对”和库仑摩擦模型描述。模型可以模拟土钉发生较大抗拔位移下发生滑移破坏的过程。模型参数通过三轴试验结果进行校正。通过与大尺寸室内抗拔试验结果相比较,验证了模型的有效性。模型展现了土钉在钻孔后和抗拔过程中土钉周围的土压力的变化。最后通过参数分析,研究了上覆压力和剪胀对土钉抗拔力的影响。结果显示,当上覆压力较小时,剪胀角对抗拔应力的影响较小。随着上覆压力的增加,剪胀角对抗拔应力的影响变得更加明显。 相似文献
18.
筋-土界面强度参数是加筋结构设计和稳定分析的关键技术指标。拉拔试验能较好模拟现场加筋行为而得到广泛的应用。基于拉拔和直剪试验研究了拉拔（剪切）速率对筋-土界面特性和吹填砂强度特性的影响规律及机制,同时探讨了不同填料界面、筋材类型的加筋效果。结果表明：随着拉拔（剪切）速率的增大,吹填砂-筋材-吹填砂界面的抗剪强度下降明显,而软土-筋材-吹填砂界面以及砂本身强度则变化不大。从强度指标来看,拉拔速率增大,筋-砂界面强度的降低主要表现为似黏聚力的降低,筋-软土界面抗剪强度的增加表现为内摩擦角增大,剪切速率对吹填砂则基本无影响。筋-土界面特性受拉拔速率和正应力的共同影响,与筋材类型和填料特性有关。筋-土界面内摩擦角小于填料摩擦角,但在一定正应力下低速剪切时（如<0.53 mm/min）可获得高于填料的抗剪强度。宜根据似黏聚力大小合理选择摩擦参数进行加筋结构的设计与评价。 相似文献
19.
Pressure-grouted soil nails have been increasingly used for stabilizing slopes. The pullout resistance of a soil nail is the main factor for reinforcing the slope stability. In this study, a two-dimensional axisymmetric finite element model is developed to simulate the pullout behavior of a pressure-grouted soil nail. This model is verified with field pullout tests result of a pressure-grouted soil nails by comparing with gravity-grouted soil nails. Based on the analysis, a three-dimensional finite element model is proposed for stability analysis of a slope reinforced with pressure-grouted soil nails using the shear strength reduction method. A series of numerical slope stability analyses for a slope composed of weathered soil are performed to investigate the effects of grouting pressure on the slope stability and the behavior of the soil nails. Special attention is given to the installation effect of a pressure-grouted soil nails. It is found from the result of this study that the pressure-grouted soil nails increase the safety factor by fifty percent in a slope by increasing the stiffness of the nailed slope system. Numerical analysis results confirm the fact that the pullout resistance of a soil nail is the main factor for stabilizing slopes rather than the shear resistance of the soil nail. 相似文献