共查询到20条相似文献，搜索用时 31 毫秒
1.
To determine the shear wave velocity structure and predominant period features of T?naztepe in ?zmir, Turkey, where new building sites have been planned, active–passive surface wave methods and single-station microtremor measurements are used, as well as surface acquisition techniques, including the multichannel analysis of surface waves (MASW), refraction microtremor (ReMi), and the spatial autocorrelation method (SPAC), to pinpoint shallow and deep shear wave velocity. For engineering bedrock (V s > 760 m/s) conditions at a depth of 30 m, an average seismic shear wave velocity in the upper 30 m of soil (AVs30) is not only accepted as an important parameter for defining ground behavior during earthquakes, but a primary parameter in the geotechnical analysis for areas to be classified by V s30 according to the National Earthquake Hazards Reduction Program (NEHRP). It is also determined that Z1.0, which represents a depth to V s = 1000 m/s, is used for ground motion prediction and changed from 0 to 54 m. The sediment–engineering bedrock structure for T?naztepe that was obtained shows engineering bedrock no deeper than 30 m. When compared, the depth of engineering bedrock and dominant period map and geology are generally compatible. 相似文献
2.
A practical method is presented for determining three‐dimensional S‐wave velocity (VS) profile from microtremor measurements. Frequency–wave number (f–k) spectral analyses of microtremor array records are combined, for this purpose, with microtremor horizontal‐to‐vertical (H/V) spectral ratio techniques. To demonstrate the effectiveness of the proposed method, microtremor measurements using arrays of sensors were conducted at six sites in the city of Kushiro, Japan. The spectral analyses of the array records yield dispersion characteristics of Rayleigh waves and H/V spectra of surface waves, and joint inversion of these data results in VS profiles down to bedrock at the sites. Conventional microtremor measurements were performed at 230 stations within Kushiro city, resulting in the H/V spectra within the city. Three‐dimensional VS structure is then estimated from inversion of the H/V spectra with the VS values determined from the microtremor array data. This reveals three‐dimensional VS profile of Kushiro city, together with an unknown hidden valley that crosses the central part of the city. The estimated VS profile is consistent with available velocity logs and results of subsequent borings, indicating the effectiveness of the proposed method. Copyright © 2008 John Wiley & Sons, Ltd. 相似文献
3.
In western India during the Bhuj earthquake (Mw 7.6) on January 26, 2001, the Anjar City at ~30 km southwest of Bhuj experienced three types of damage scenario: severely damaged, less damaged and non-damaged. Similar damage patterns were also observed for the 1819 (Mw 7.8) and the 1956 (Mw 6.0) earthquakes. Microtremor array measurements were conducted in and around the Anjar city to examine the strength of soil structures and damage pattern. Significant differences are observed in frequencies and amplitudes in horizontal-to-vertical spectral ratio (HVSR) using microtremor measurements. The severely- damaged site shows two peak amplitudes: 2.8 at 1.2 Hz; and 4.0 at 8.0 Hz. The less-damaged site also shows two amplitudes: 2.5 and 2.1 at 1.4 Hz; and 2.0 Hz, respectively. The non-damaged site, on the other hand, shows that the HVSR curves become almost flatter. Similar results for three types of damage scenario based on analyses of earthquake records are also observed for the study area. The microtremor array measurements has revealed shear wave velocity Vs≥400 m/s at 18 m depth in the non-damaged, at 40 m in the less-damaged and at 60 m depth in the severely-damaged sites. The site amplitudes and the Vs values show a good correlation with the soil characteristics and damage pattern, suggesting that strength of soil layers at varying depths is a dictating factor for the estimate of the earthquake risk evaluation of the area under study. 相似文献
4.
土体剪切波速是进行土层地震反应分析的动力学参数，对场地地震动参数确定具有重要意义。基于地质地貌分析，将大同盆地划分为5类典型地质单元。对盆地1429个钻孔剪切波速资料进行分析，探讨VS30与VS20的相关性，研究土体埋深、岩性、地质单元、标贯击数及密实度等地质特征对VS的影响，并基于地质单元、剪切波速比、密实度系数及第四系上部覆盖层厚度相关性分析给出土体VS30预测模型。研究结果表明，基于典型地质特征的VS30预测模型拟合优度R2>0.90，预测精度很高，对于离散性较大、直接拟合估算较差及无剪切波速场地来说，以区分地质单元及土体类型的方式进行VS30分解预测是良好的研究思路。首次在区分地质单元及土体类型的前提下提出剪切波速比及密实度系数，并将其与第四系上部覆盖层厚度综合应用于VS30预测研究。研究结果可为大同盆地城市防震减灾规划、震害预测、区域性地震安全评价提供重要技术支撑。 相似文献
5.
中山市城区场地土层剪切波速及脉动特征 总被引：1，自引：1，他引：1
对中山市城区场地剪切波速及地面脉动测试的实测数据进行了统计分析，并结合土层厚度和其他地质资料的研究，得到中山市城区场土层剪切波速和地面脉动的分析特征以及场地土类型和建筑场地类别的分布，并对影响土层煎速度及脉周期的各种因素作了初步探讨。 相似文献
6.
Seismic site characterization is the basic requirement for seismic microzonation and site response studies of an area. Site characterization helps to gauge the average dynamic properties of soil deposits and thus helps to evaluate the surface level response. This paper presents a seismic site characterization of Agartala city, the capital of Tripura state, in the northeast of India. Seismically, Agartala city is situated in the Bengal Basin zone which is classified as a highly active seismic zone, assigned by Indian seismic code BIS-1893, Indian Standard Criteria for Earthquake Resistant Design of Structures, Part-1 General Provisions and Buildings. According to the Bureau of Indian Standards, New Delhi (2002), it is the highest seismic level (zone-V) in the country. The city is very close to the Sylhet fault (Bangladesh) where two major earthquakes (M w > 7) have occurred in the past and affected severely this city and the whole of northeast India. In order to perform site response evaluation, a series of geophysical tests at 27 locations were conducted using the multichannel analysis of surface waves (MASW) technique, which is an advanced method for obtaining shear wave velocity (V s) profiles from in situ measurements. Similarly, standard penetration test (SPT-N) bore log data sets have been obtained from the Urban Development Department, Govt. of Tripura. In the collected data sets, out of 50 bore logs, 27 were selected which are close to the MASW test locations and used for further study. Both the data sets (V s profiles with depth and SPT-N bore log profiles) have been used to calculate the average shear wave velocity (V s30) and average SPT-N values for the upper 30 m depth of the subsurface soil profiles. These were used for site classification of the study area recommended by the National Earthquake Hazard Reduction Program (NEHRP) manual. The average V s30 and SPT-N classified the study area as seismic site class D and E categories, indicating that the city is susceptible to site effects and liquefaction. Further, the different data set combinations between V s and SPT-N (corrected and uncorrected) values have been used to develop site-specific correlation equations by statistical regression, as ‘V s’ is a function of SPT-N value (corrected and uncorrected), considered with or without depth. However, after considering the data set pairs, a probabilistic approach has also been presented to develop a correlation using a quantile–quantile (Q–Q) plot. A comparison has also been made with the well known published correlations (for all soils) available in the literature. The present correlations closely agree with the other equations, but, comparatively, the correlation of shear wave velocity with the variation of depth and uncorrected SPT-N values provides a more suitable predicting model. Also the Q–Q plot agrees with all the other equations. In the absence of in situ measurements, the present correlations could be used to measure V s profiles of the study area for site response studies. 相似文献
7.
目前我国建筑工程抗震设计规范中对于工程场地条件的判断依据主要是地表以下20m深度范围内土层的等效剪切波速,简称VS20。相比之下,国外应用较广的是地表以下30m深度范围内的等效剪切波速,简称VS30。这种差别导致国内科研工作者在应用国外的地震工程、工程抗震模型时经常遇到对场地条件描述不准确的困难。为了解决这个问题,本文根据147个四川、甘肃地区国家强震动台站20m左右深度的钻孔剪切波速数据,利用延拓方法、场地分类统计方法以及基于地形特征的VS30估计方法研究各台站VS30与VS20的经验关系,对比发现基于速度梯度延拓的结果最为可取。参考国际上通用的Geomatrix Classification场地分类标准,最终得到四川、甘肃地区各类场地的平均VS30,此结果可以为缺乏钻孔数据的工程场地的VS30估计提供参考。 相似文献
8.
We made an attempt to assess the shear wave velocity values V S and, to a lesser extent, the V P values from ambient noise recordings in an array configuration. Five array sites were situated in the close proximity to borehole sites. Shear wave velocity profiles were modeled at these five array sites with the aid of two computational techniques, viz. spatial autocorrelation (SPAC) and H/V ellipticity. Out of these five array sites, velocity estimates could be reliably inferred at three locations. The shear wave velocities estimated by these methods are found to be quite consistent with each other. The computed V S values up to 30 m depth are in the range from 275 to 375 m/s in most of the sites, which implies prevalence of a low velocity zone at some pocket areas. The results were corroborated by evidence of site geology as well as geotechnical information. 相似文献
9.
Brent L. Rosenblad Jonathan Bailey Ryan Csontos Roy Van Arsdale 《Soil Dynamics and Earthquake Engineering》2010
Deep unconsolidated sediments in the Mississippi embayment will influence ground motions from earthquakes in the New Madrid seismic zone. Shear wave velocity profiles of these sediments are important input parameters for modeling wave propagation and site response in this region. Low-frequency, active-source surface wave velocity measurements were performed to develop small-strain shear wave velocity (VS) profiles at eleven deep soil sites in the Mississippi embayment, from north of New Madrid, Missouri to Memphis, Tennessee. A servo-hydraulic, low-frequency source was used to excite surface wave energy to wavelengths of 600 m, resulting in VS profiles to depths of over 200 m. The average VS profile calculated from the eleven sites is in good agreement with common reference VS profiles that have been used in seismic hazard studies of this region. The variability in VS profiles is shown to be associated with changes in formation depth and thickness from site-to-site. Using lithologic information at each site, average formation velocities were developed and compared to previous studies. We found average VS values of about 193 m/s for alluvial deposits, 400 m/s for the Upper Claiborne formations, and 685 m/s for the Memphis Sand formation. 相似文献
10.
The liquefaction potential of soils is traditionally assessed through geotechnical approaches based on the calculation of the cyclical stress ratio (CSR) induced by the expected earthquake and the ‘resistance’ provided by the soil, which is quantified through standard penetration (SPT), cone penetration (CPT), or similar tests. In more recent years, attempts to assess the liquefaction potential have also been made through measurement of shear wave velocity (VS) in boreholes or from the surface. The latter approach has the advantage of being non-invasive and low cost and of surveying lines rather than single points. However, the resolution of seismic surface techniques is lower than that of borehole techniques and it is still debated whether it is sufficient to assess the liquefaction potential.In this paper we focus our attention on surface seismic techniques (specifically the popular passive and active seismic techniques based on the correlation of surface waves such as ReMiTM, MASW, ESAC, SSAP, etc.) and explore their performance in assessing the liquefaction susceptibility of soils. The experimental dataset is provided by the two main seismic events of ML=5.9 and 5.8 (MW=6.1, MW=6.0) that struck the Emilia-Romagna region (Northern Italy) on May 20 and 29, 2012, after which extensive liquefaction phenomena were documented in an area of 1200 km2.The CPT and drillings available in the area allow us to classify the soils into four classes: A) shallow liquefied sandy soils, B) shallow non-liquefied sandy soils, C) deep non-liquefied sandy soils, and D) clayey–silty soils, and to determine that on average class A soils presented a higher sand content at the depth of 5–8 m compared to class B soils, where sand was dominant in the upper 5 m. Surface wave active–passive surveys were performed at 84 sites, and it was found that they were capable of discriminating among only three soil classes, since class A and B soils showed exactly the same VS distribution, and it is possible to show both experimentally and theoretically that they appear not to have sufficient resolution to address the seismic liquefaction issue.As a last step, we applied the state-of-the art CSR–VS method to assess the liquefaction potential of sandy deposits and we found that it failed in the studied area. This might be due to the insufficient resolution of the surface wave methods in assessing the Vs of thin layers and to the fact that Vs scales with the square root of the shear modulus, which implies an intrinsic lower sensitivity of Vs to the shear resistance of the soil compared to parameters traditionally measured with the penetration tests. However, it also emerged that the pure observation of the surface wave dispersion curves at their simplest level (i.e. in the frequency domain, with no inversion) is still potentially informative and can be used to identify the sites where more detailed surveys to assess the liquefaction potential are recommended. 相似文献
11.
Subsurface lithology and seismic site classification of Lucknow urban center located in the central part of the Indo-Gangetic Basin (IGB) are presented based on detailed shallow subsurface investigations and borehole analysis. These are done by carrying out 47 seismic surface wave tests using multichannel analysis of surface waves (MASW) and 23 boreholes drilled up to 30 m with standard penetration test (SPT) N values. Subsurface lithology profiles drawn from the drilled boreholes show low- to medium-compressibility clay and silty to poorly graded sand available till depth of 30 m. In addition, deeper boreholes (depth >150 m) were collected from the Lucknow Jal Nigam (Water Corporation), Government of Uttar Pradesh to understand deeper subsoil stratification. Deeper boreholes in this paper refer to those with depth over 150 m. These reports show the presence of clay mix with sand and Kankar at some locations till a depth of 150 m, followed by layers of sand, clay, and Kankar up to 400 m. Based on the available details, shallow and deeper cross-sections through Lucknow are presented. Shear wave velocity (SWV) and N-SPT values were measured for the study area using MASW and SPT testing. Measured SWV and N-SPT values for the same locations were found to be comparable. These values were used to estimate 30 m average values of N-SPT (N 30) and SWV (V s 30 ) for seismic site classification of the study area as per the National Earthquake Hazards Reduction Program (NEHRP) soil classification system. Based on the NEHRP classification, the entire study area is classified into site class C and D based on V s 30 and site class D and E based on N 30. The issue of larger amplification during future seismic events is highlighted for a major part of the study area which comes under site class D and E. Also, the mismatch of site classes based on N 30 and V s 30 raises the question of the suitability of the NEHRP classification system for the study region. Further, 17 sets of SPT and SWV data are used to develop a correlation between N-SPT and SWV. This represents a first attempt of seismic site classification and correlation between N-SPT and SWV in the Indo-Gangetic Basin. 相似文献
12.
Array measurements of microtremors were carried out at thirty sites in Damascus city, Syria to estimate S-wave velocity structures of shallow soil formations for site effect analysis. The microtremor data were recorded by 6 vertical-component seismometers distributed along the circumferences of two circles as well as a 3-component seismometer deployed in the center. The phase velocities were estimated at each site from the vertical components of recorded microtremor data by using the Spatial Autocorrelation method. Then, Genetic Simulated Annealing Algorithm technique was applied for inversion of the phase velocities to estimate 1-D S-wave velocity structures beneath the sites. The inverted Vs profiles are not uniform in Damascus city and the results show that a shallow soft layer (∼200 m/s) appears in the eastern part of the city as well as the central part along Barada River. This layer controls the amplification distribution in the city with a high amplification mainly observed at the locations having this layer. The inversion results also show that the depth to the engineering bedrock (∼750 m/s) is very shallow along the foothills of Mt. Qasyoun in the north-west. Then the depth increases towards the east and the south. The maximum depth to the engineering bedrock (∼80 m) was observed in the southern part of Damascus. To validate the results of the inversions, the spectral ratios between the horizontal and vertical components (H/V) of the recorded microtremor data at the central seismometer were compared with the computed ellipticities of the fundamental-mode Rayleigh-waves based on the respective Vs structure. The results show a good agreement in a period range of 0.05 s to 0.5 s. In this period range, the dominant peaks of the H/V ratios are due to the overall effect of the velocity contrasts between the shallow layers representing the subsurface S-wave velocity structure. Moreover, the average S-wave velocity for the top 10 m of soils (VS10) shows a better correlation with the averaged site amplification in a period range of 0.05 s to 0.5 s than VS30 which indicates that VS10 can be a better proxy for high-frequency site amplification in the case of Damascus city. 相似文献
13.
Hing-Ho Tsang M. Neaz SheikhNelson T.K. Lam 《Soil Dynamics and Earthquake Engineering》2012,34(1):89-98
Where a distinct soil-rock interface exists, the bedrock medium is commonly treated as elastic half-space and the bedrock surface as the lower boundary of the soil-column model for site response analyses (or the lower boundary of the finite element model for soil-structure interaction analyses). While shear wave velocity in bedrock varies with depth, there has been no consensus amongst scientists and practitioners over the value of “effective depth” into bedrock at which the “half-space” shear wave velocity value should be taken for modeling purposes. This paper reports an interesting and important observation that the effective depth into bedrock is sensitive to the shear wave velocity profile of the overlying soil sediments. A simple and heuristic method, namely Resonant Period Equivalence (RPE) Method, is proposed herein for representing a stratified elastic bedrock of inhomogeneous properties by an equivalent homogeneous elastic half-space medium, which is characterized by a single equivalent shear wave velocity (VR) value. The proposed calculation method has been verified by extensive comparative analyses involving the use of programs SHAKE and NERA and employing the complete shear wave velocity models of both the soil sediments and the underlying stratified bedrock. 相似文献
14.
剪切波速与地基土的抗剪强度、剪切模量和卓越周期等参数密切相关,是地震安全性评价中判定场地类别的一个主要指标和参数。鉴于海域工程中剪切波速往往难以直接由原位测得,而室内实验结果又常常与野外现场物探测试值存在较大差异,因此,如何通过其他途径有效获取满足工程需要的剪切波速参数在海域工程的地震安全性评价等方面具有迫切的实用需求。为此本文通过对渤海海域数十个石油平台项目中一系列饱和黏性土样品的剪切波速与抗剪强度实验数据的统计分析,尝试采用多种可能的函数来拟合确定二者之间的经验关系。结果表明:对于渤海海域黏性土剪切波速V_s与抗剪强度S_u之间的最佳统计经验关系为幂函数V_s=53.751S_u~(0.376)。此关系可为渤海海域工程中通过不排水抗剪强度估算剪切波速提供一种简便可行的实用性方法。 相似文献
15.
Mapping the thickness of sediments in the Ljubljana Moor basin (Slovenia) using microtremors 总被引：2，自引：0，他引：2
The Ljubljana Moor basin is characterized by moderate bedrock topography and thicknesses of Quaternary lacustrine and fluvial
sediments ranging from 0 to 200 m. More than 65 boreholes which reached the bedrock were drilled in the area, but their distribution
in the basin is very uneven and some data from the boreholes uncertain. There are also no data on S-velocity distribution
within the basin, but seismic refraction measurements pointed out a rather uniform increase of P-velocity with depth, great
impedance contrast with the bedrock and relatively small lateral velocity variations. The microtremor horizontal-to-vertical
spectral ratio (HVSR) method was therefore applied as a complementary tool to seismic refraction survey to map the thickness
of sediments. First, microtremors were measured at the locations of boreholes which reached the bedrock and the resonance
frequencies determined. The inverse power relationship between the resonance frequency and the thickness of sediments was
then determined from 53 data pairs. The quality of the correlation is moderate due to possible heterogeneities in sediments
and possible 3D effects in some minor areas, but the obtained parameters correspond well to the values obtained in six other
European basins. Secondly, a 16 km-long discontinuous seismic refraction profile was measured across the whole basin, leaving
uncovered some larger segments where active seismic measurements were not possible. Microtremors were then measured at 64
locations along the same profile, using 250 m point spacing, without leaving any gaps. The frequency–thickness relationship
was used to invert resonance frequencies to depths. These were first validated using the results of the seismic refraction
survey, which showed good agreement, and finally used for interpolation in the segments of missing refraction data to obtain
a continuous depth profile of the bedrock. The study has shown that the microtremor method can be used as a complementary
tool for mapping the thickness of unconsolidated sediments also in areas characterized by moderate bedrock topography. As
the input data are always to some extent uncertain, it is important to have a sufficiently large number of borehole data to
establish a frequency–thickness relationship, as well as some additional independent geophysical information for its validation. 相似文献
16.
This paper has two objectives: to connect directly radiation damping and 1D elastic wave propagation, and to create a simple teaching tool to introduce the subject to students and engineers trained in Structural Dynamics. The first objective is achieved by obtaining the equivalent radiation modal damping using time domain solutions for the fundamental mode in shear of an elastic layer (soil) on flexible rock, for the case in which the rock–soil Impedance Ratio in shear, I=(ρrVr)/(ρsVs)>1, where ρ=mass density and V=shear wave velocity. These time domain solutions are developed for the case of steady-state input sinusoidal shear waves propagating vertically in the rock as well as for horizontal free vibration of the layer. Both derivations result in the same approximate expression for the modal radiation damping in the first mode, ζr1≈2/(πI), which is in turn identical to the approximate equation obtained by Roesset and Whitman [11] using a frequency domain approach. This expression for ζr1 is linked to the fact that, during free vibration, the ratio between two successive positive displacement peaks uso and us1 at the ground surface is us0/us1=[(1+I)/(1−I)]2, associated with two wave reflections at the soil–rock interface. From this ratio, and after applying the standard expression to obtain modal damping from damped free vibration, the same expression for ζr1 is reached again, ζr1≈[1/(2π)] ln(us0/us1)≈[1/(2π)] ln[(1+I)/(1−I)]2≈2/(πI). This finding allows development of the simple teaching tool proposed at the end of the paper. While only a crude approximation lacking in rigor, this teaching tool is physically intuitive, links directly wave propagation and modal damping in a simple way and gives the correct result. 相似文献
17.
The junction between lithosphere and asthenosphere for the oceanic and continental mantles is usually defined as the depth where the shear velocity suddenly decreases. It now also appears reasonable to define the junction in terms of a sudden increase in the dissipating properties of the lower of the two boundary materials. Using new data for the suboceanic upper mantle it is possible to deduce the relative thinning of the lithosphere under the oceans compared to the continents from the variation with frequency of the Rayleigh wave specific attenuation factorQγ?1. 相似文献
18.
The crustal structure in Myanmar can provide valuable information for the eastern margin of the ongoing Indo-Eurasian collision system. We successively performed H–k stacking of the receiver function and joint inversion of the receiver function and surface wave dispersion to invert the crustal thickness (H), shear wave velocity (VS), and the VP/VS ratio (k) beneath nine permanent seismic stations in Myanmar. H was found to increase from 26 ?km in the south and east of the study area to 51 ?km in the north and west, and the VP/VS ratio was complex and high. Striking differences in the crust were observed for different tectonic areas. In the Indo-Burma Range, the thick crust (H ?～ ?51 ?km) and lower velocities may be related to the accretionary wedge from the Indian Plate. In the Central Myanmar Basin, the thin crust (H ?= ?26.9–35.5 ?km) and complex VP/VS ratio and VS suggest extensional tectonics. In the Eastern Shan Plateau, the relatively thick crust and normal VP/VS ratio are consistent with its location along the western edge of the rigid Sunda Block. 相似文献
19.
Based on the liquefaction performance of sites with seismic activity, the normalized shear wave velocity, Vs1, has been proposed as a field parameter for liquefaction prediction. Because shear wave velocity, Vs, can be measured in the field with less effort and difficulty than other field tests, its use by practitioners is highly attractive. However, considering that its measurement is associated with small strain levels, of the order of 10−4–10−3%, Vs reflects the elastic stiffness of a granular material, hence, it is mainly affected by soil type, confining pressure and soil density, but it is insensitive to factors such as overconsolidation and pre-shaking, which have a strong influence on the liquefaction resistance. Therefore, without taking account of the important factors mentioned above, the correlation between shear wave velocity and liquefaction resistance is weak.In this paper, laboratory test results are presented in order to demonstrate the significant way in which OCR (overconsolidation ratio) affects both shear wave velocity and liquefaction resistance. While Vs is insensitive to OCR, the liquefaction resistance increases significantly with OCR. In addition, the experimental results also confirm that Vs correlates linearly with void ratio, regardless of the maximum and minimum void ratios, which means that Vs is unable to give information about the relative density. Therefore, if shear wave velocity is used to predict liquefaction potential, it is recommended that the limitations presented in this paper be taken into account. 相似文献
20.
Chun-Hsiang Kuo Kuo-Liang Wen Hung-Hao Hsieh Tao-Ming Chang Che-Min Lin Chun-Te Chen 《Soil Dynamics and Earthquake Engineering》2011
The shear wave velocity of shallow sediments is very important in seismic wave amplification and thus Vs30 is a well-known parameter for site classification. Based on the relationship between Vs and soil indexes, the empirical regression equations were evaluated using more than 600 data sets from the Ilan area and the Taipei Basin. Multivariable analysis, which can increase the accuracy of regression equations, was used in this study. Three extrapolations were compared, and then the most accurate bottom-constant extrapolation was adopted to estimate Vs30 at 16 boreholes, none of which reached a depth of 30 m. Ultimately Vs30 was derived for 110 free-field strong motion stations, and the stations in northeastern Taiwan were reclassified according to the Vs30-based NEHRP provisions. Regression equations of Vs and the extrapolation of Vs30 were also applied to boreholes with only N-values and corresponding depths of less than 30 m for assessing the Vs30 and NEHRP class. 相似文献