首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献，搜索用时 328 毫秒
1.
The Platanares geothermal area, Departamento de Copán, Honduras, is located within a graben that is complexly faulted. The graben is bounded on the north by a highland composed of Paleozoic (?) metamorphic rocks in contact with Cretaceous - Tertiary redbeds of unknown thickness. These are unconformably overlain by Tertiary andesitic lavas, rhyolitic ignimbrites, and associated sedimentary rocks. The volcanic rocks are mostly older than 14 Ma, and thus are too old to represent the surface expression of an active crustal magma body. Thermal fluids that discharge in the area are heated during deep circulation of meteoric water along faults in a region of somewhat elevated heat flow. Geothermometry based upon the chemical composition of thermal fluids from hot springs and from geothermal gradient coreholes suggests that the reservoir equilibrated at temperatures as high as 225 to 240°C, within the Cretaceous redbed sequence. Three continuously cored geothermal gradient holes have been drilled; fluids of about 165°C have been produced from two drilled along a NW-trending fault zone, from depths of 250 to 680 m. A conductive thermal gradient of 139°C/km, at a depth of 400 m, was determined from the third well, drilled 0.6 km west of that fault zone. These data indicate that the Platanares geothermal area holds considerable promise for electrical generation by moderate- to hightemperature geothermal fluids.  相似文献   

2.
The Sierra La Primavera, a late Pleistocene rhyolitic caldera complex in Jalisco, México, contains fumaroles and large-discharge 65°C hot springs that are associated with faults related to caldera collapse and to later magma insurgence. The nearly-neutral, sodium bicarbonate, hot springs occur at low elevations at the margins of the complex, whereas the water-rich fumaroles are high and central.The Comisión Federal de Electricidad de México (CFE) has recently drilled two deep holes at the center of the Sierra (PR-1 and Pr-2) and one deep hole at the western margin. Temperatures as high as 285°C were encountered at 1160 m in PR-1, which produced fluids with 820 to 865 mg/kg chloride after flashing to one atmosphere. Nearby, PR-2 encountered temperatures to 307°C at 2000 m and yielded fluids with chloride contents fluctuating between 1100 and 1560 mg/kg after flashing. Neither of the high-temperature wells produced steam in commercial quantities. The well at the western margin of the Sierra produced fluids similar to those from the hot springs. The temperature reached a maximum of 100°C near the surface and decreased to 80°C at 2000 m.Various geothermometers (quartz conductive, Na/K, Na-K-Ca, δ18O(SO4-H2O) and D/H (steam-water) all yield temperatures of 170 ± 20°C when applied to the hot spring waters, suggesting that these spring waters flow from a large shallow reservoir at this temperature. Because the hot springs are much less saline than the fluids recovered in PR-1 and PR-2, the mixed fluid in the shallow reservoir can contain no more than 10–20% deep fluid. This requires that most of the heat is transferred by steam. There is probably a thin vapor-dominated zone in the central part of the Sierra, through which steam and gases are transferred to the overlying shallow reservoir. Fluids from this reservoir cool from 170°C to 65°C by conduction during the 5–7 km of lateral flow to the hot springs.  相似文献   

3.
The Platanares geothermal area in western Honduras consists of more than 100 hot springs that issue from numerous hot-spring groups along the banks or within the streambed of the Quebrada de Agua Caliente (brook of hot water). Evaluation of this geothermal area included drilling a 650-m deep PLTG-1 drill hole which penetrated a surface mantling of stream terrace deposits, about 550 m of Tertiary andesitic lava flows, and Cretaceous to lower Tertiary sedimentary rocks in the lower 90 m of the drill core.Fractures and cavities in the drill core are partly to completely filled by hydrothermal minerals that include quartz, kaolinite, mixed-layer illite-smectite, barite, fluorite, chlorite, calcite, laumontite, biotite, hematite, marcasite, pyrite, arsenopyrite, stibnite, and sphalerite; the most common open-space fillings are calcite and quartz. Biotite from 138.9-m depth, dated at 37.41 Ma by replicate 40Ar/39 Ar analyses using a continuous laser system, is the earliest hydrothermal mineral deposited in the PLTG-1 drill core. This mid-Tertiary age indicates that at least some of the hydrothermal alteration encountered in the PLTG-1 drill core occured in the distant past and is unrelated to the present geothermal system. Furthermore, homogenization temperatures (Th) and melting-point temperatures (Tm) for fluid inclusions in two of the later-formed hydrothermal minerals, calcite and barite, suggest that the temperatures and concentration of dissolved solids of the fluids present at the time these fluid inclusions formed were very different from the present temperatures and fluid chemistry measured in the drill hole.Liquid-rich secondary fluid inclusions in barite and caicite from drill hole PLTG-1 have Th values that range from about 20°C less than the present measured temperature curve at 590.1-m depth to as much as 90°C higher than the temperature curve at 46.75-m depth. Many of the barite Th measurements (ranging between 114° and 265°C) plot above the reference surface boiling-point curve for pure water assuming hydrostatic conditions; however, the absence of evidence for boiling in the fluid inclusions indicates that at the time the minerals formed, the ground surface must have been at least 80 m higher than at present and underwent stream erosion to the current elevation. Near-surface mixed-layer illite-smectite is closely associated with barite and appears to have formed at about the same temperature range (about 120° to 200°C) as the fluid-inclusion Thvalues for barite. Fluid-inclusion Th values for calcite range between about 136° and 213°C. Several of the calcite Th values are significantly lower than the present measured temperature curve. The melting-point temperatures (Tm) of fluid-inclusion ice yield calculated salinities, ranging from near zero to as much as 5.4 wt. % NaCl equivalent, which suggest that much of the barite and calcite precipitated from fluids of significantly greater salinity than the present low salinity Platanares hot-spring water or water produced from the drill hole.  相似文献   

4.
The Latera field (Vulsini volcanic complex, Latium, Italy) is one of the geothermal areas of the peri-Tyrrhenian belt along which a regional, high thermal anomaly has been detected. So far nine deep wells have been drilled within the Latera caldera and four of them have been productive. The geothermal reservoir is located within the fractured carbonatic rocks of the Tuscan nappe; the overlying volcanic units, sealed by hydrothermal minerals (mainly calcite and anhydrite), act as an impervious cover.The fluid produced by the wells comes from a deep aquifer (about 1000–1500 m depth) which at present is not connected with the shallow aquifer in the volcanoclastic units. Fluid temperatures range between 200 and 230°C; in-hole temperatures as high as 343°C at 2775 m depth have been measured in dry wells.The study of the newly formed mineral assemblages from both volcanic and sedimentary units as sampled from the geothermal wells can be used to reconstruct the thermal evolution of the geothermal field. The intrusion of a syenitic melt, up to a depth of about 2000 m, dated 0.86 Ma, represents the major thermal event for the units in the area and is assumed to represent the first step in the geothermal evolution of the Latera system.The above mentioned newly formed mineral assemblages can be divided into three groups: (a) “contact-metasomatic”: calcite, anhydrite, diopsidic pyroxene, grossularitic garnet, phlogopite, wollastonite or monticellite; (b) “high-temperature hydrothermal”: calcite, anhydrite, K-feldspar, vesuvianite, melanitic garnet, tourmaline, amphibole, epidote, sulphides; (c) “low-temperature hydrothermal”: calcite, anhydrite, K-feldspar, clay minerals, sulphides. Group (a) minerals are now relics. Part of (b) and all of (c) group are still in equilibrium with the existing conditions in different parts of the geothermal system.Thermodynamic calculations on the observed mineral assemblages permitted estimates of the P, T conditions and gas fugacities.  相似文献   

5.
Detailed geochemistry supported by geologic mapping has been used to investigate Sulphur Springs, an acid-sulfate hot spring system that issues from the western flank of the resurgent dome inside Valles Caldera. The most intense activity occurs at the intersection of faults offsetting caldera-fill deposits and post-caldera rhyolites. Three geothermal wells in the area have encountered pressures <1 MPa and temperatures of 200°C at depths of 600 to 1000 m. Hot spring and fumarole fluids may discharge at boiling temperatures with pH 1.0 and SO4 8000 mg/l. These conditions cause argillic alterations throughout a large area.Non-condensible gases consist of roughly 99% CO2 with minor amounts of H2S, H2, and CH4. Empirical gas geothermometry suggests a deep reservoir temperature of 215 to 280°C. Comparison of 13C and 18O between CaCO3 from well cuttings and CO2 from fumarole steam indicates a fractionation temperature between 200 and 300°C by decarbonation of hydrothermally altered Paleozoic limestone and vein calcite in the reservoir rocks. Tritium concentrations obtained from steam condensed in a mudpot and deep reservoir fluids (Baca #13, 278°C) are 2.1 and 1.0 T.U. respectively, suggesting the steam originates from a reservoir whose water is mostly >50 yrs old. Deuterium contents of fumarole steam, deep reservoir fluid, and local meteoric water are practically identical even though 18O contents range through 4‰, thus, precipitation on the resurgent dome of the caldera could recharge the hydrothermal system by slow percolation. From analysis of D and 18O values between fumarol steam and deep reservoir fluid, steam reaches the surface either (1) by vaporizing relatively shallow groundwater at 200°C or (2) by means of a two-stage boiling process through an intermediate level reservoir at roughly 200°C.Although many characteristics of known vapor-dominated geothermal systems are found at Sulphur Springs, fundamental differences exist in temperature and pressure of our postulated vapor-zone. We propose that the reservoir beneath Sulphur Springs is too small or too poorly confined to sustain a “true” vapor-dominated system and that the Sulphur Springs system may be a “dying” vapor-dominated system that has practically boiled itself dry.  相似文献   

6.
To understand the crustal electric structure of the Puga geothermal field located in the Ladakh Himalayas, wide band (1000 Hz–0.001 Hz) magnetotelluric (MT) study have been carried out in the Puga area. Thirty-five MT sites were occupied with site spacing varying from 0.4 to 1 km. The measurements were carried out along three profiles oriented in east–west direction. After the preliminary analysis, the MT data were subjected to decomposition techniques. The one-dimensional inversion of the effective impedance data and the two-dimensional inversion of the TE (transverse electric) and TM (transverse magnetic) data confirm the presence of low resistive (5–25 Ω m) near surface region of 200–300 m thick in the anomalous geothermal part of the area related to the shallow geothermal reservoir. Additionally, the present study delineated an anomalous conductive zone (resistivity less than 10 Ω m) at a depth of about 2 km which is possibly related to the geothermal source in the area. A highly resistive basement layer separates the surface low resistive region and anomalous conductive part. The estimated minimum temperature at the top of conductive part is about 250 °C. The significance of the deeper conductive zone and its relation to the geothermal anomaly in the area is discussed.  相似文献   

7.
The Campi Flegrei (Naples, Campanian Plain, southern Italy) geothermal system is hosted by Quaternary volcanic rocks erupted before, during and after the formation of the caldera that represents one of the major structural features in the Neapolitan area. The volcanic products rest on a Mesozoic carbonate basement, cropping out north, east and south of the area. Chemical (major, minor and trace elements) and stable isotope (C, H, O) analyses were conducted on drill-core samples recovered from geothermal wells MF-1, MF-5, SV-1 and SV-3, at depths of ˜ 1100 to 2900 m. The study was complemented by petrographic and SEM examination of thin sections. The water which feeds the system is both marine and meteoric in origin. Mineral zonation typical of a high-temperature geothermal system exists in all the geothermal wells; measured temperatures in wells are as high as ˜ 400 °C. The chemical composition of the waters suggests the existence of two reservoirs: a shallow reservoir (depth < 2000 m) fed by seawater that boiled at 320 °C and became progressively diluted by steam-heated local meteoric water during its ascent; and a deeper reservoir (depth > 2000 m) of hypersaline water. The drill-cores are mainly hydrothermally altered volcanics of trachy-latitic affinity, but some altered pelites and limestones are also present. Published Na, Mg and K concentrations of selected geothermal waters indicate that the hydrothermal fluids are in equilibrium with their host rocks, with respect to K-feldspar, albite, sericite and chlorite. The measured δ18O(SMOW) values of rocks range from +4.3 to + 16.5%. The measured δD(SMOW) values range from − 79 to − 46%. The calculated isotopic composition of the fluids at equilibrium with the samples vary from + 1 to + 8.3%. δ18O and from − 52 to + 1%. δD. The estimated isotopic composition of the waters at equilibrium with the studied samples confirmed the existence of two distinct fluid types circulating in the geothermal system. The shallower has a marine water signature, while the deeper water has a signature consistent both with magmatic and meteoric origins. In the latter case, the recharge of this aquifer likely occurs at the outcrop of the Mesozoic Limestones surrounding the Campanian Plain; after infiltration, the water percolates through evaporitic layers, becoming hypersaline and D-depleted.  相似文献   

8.
An exhaustive analysis of 3000 macroscopic fractures encountered in the geothermal Hot Dry Rock borehole, EPS-1, located inside the Rhine graben (Soultz-sous-Forêts, France), was done on a continuous core section over a depth interval from 1420 to 2230 m: 97% of the macroscopic structures were successfully reorientated with a good degree of confidence by comparison between core and acoustic borehole imagery. Detailed structural analysis of the fracture population indicates that fractures are grouped in two principal fractures sets striking N005 and N170 °, and dipping 70 °W and 70 °E, respectively. This average attitude is closely related to the past tectonic rifting activity of the graben during the Tertiary, and is consistent with data obtained from nearby boreholes and from neighbouring crystalline outcrops. Fractures are distributed in clusters of hydrothermally altered and fractured zones. They constitute a complex network of fault strands dominated by N–S trends, except within some of the most fractured depth intervals (1650 m, 2170 m), where an E–W-striking fracture set occurs. The geometry of the pre-existing fracture system strikes in a direction nearly parallel to the maximum horizontal stress. In this favorable situation, hydraulic injections will tend both to reactivate natural fractures at low pressures, and to create a geothermal reservoir.  相似文献   

9.
The Quaternary Takidani Granodiorite (Japan Alps) is analogous to the type of deep-seated (3–5 km deep) intrusive-hosted fracture network system that might support (supercritical) hot dry/wet rock (HDR/HWR) energy extraction. The I-type Takidani Granodiorite comprises: porphyritic granodiorite, porphyritic granite, biotite-hornblende granodiorite, hornblende-biotite granodiorite, biotite-hornblende granite and biotite granite facies; the intrusion has a reverse chemical zonation, characterized by >70 wt% SiO2 at its inferred margin and <67 wt% SiO2 at the core. Fluid inclusion evidence indicates that fractured Takidani Granodiorite at one time hosted a liquid-dominated, convective hydrothermal system, with <380°C, low-salinity reservoir fluids at hydrostatic (mesothermal) pressure conditions. ‘Healed’ microfractures also trapped >600°C, hypersaline (35 wt% NaCleq) fluids of magmatic origin, with inferred minimum pressures of formation being 600–750 bar, which corresponds to fluid entrapment at 2.4–3.0 km depth. Al-in-hornblende geobarometry indicates that hornblende crystallization occurred at about 1.45 Ma (7.7–9.4 km depth) in the (marginal) eastern Takidani Granodiorite, but later (at 1.25 Ma) and shallower (6.5–7.0 km) near the core of the intrusion. The average rate of uplift across the Takidani Granodiorite from the time of hornblende crystallization has been 5.1–5.9 mm/yr (although uplift was about 7.5 mm/yr prior to 1.2 Ma), which is faster than average uplift rates in the Japan Alps (3 mm/yr during the last 2 million years). A temperature–depth–time window, when the Takidani Granodiorite had potential to host an HDR system, would have been when the internal temperature of the intrusive was cooling from 500°C to 400°C. Taking into account the initial (7.5 mm/yr) rate of uplift and effects of erosion, an optimal temperature–time–depth window is proposed: for 500°C at 1.54–1.57 Ma and 5.2±0.9 km (drilling) depth; and 400°C at 1.36–1.38 Ma and 3.3±0.8 km (drilling) depth, which is within the capabilities of modern drilling technologies, and similar to measured temperature–depth profiles in other active hydrothermal systems (e.g. at Kakkonda, Japan).  相似文献   

10.
On the evolution of the geothermal regime of the North China Basin   总被引：1，自引：0，他引：1  
Recent heat flow and regional geothermal studies indicate that the North China Basin is characterized by relatively high heat flow compared with most stable areas in other parts of the world, but lower heat flow than most active tectonic areas. Measured heat flow values range from 61 to 74 mW m−2. The temperature at a depth of 2000 m is generally in the range 75 to 85°C, but sometimes is 90°C or higher. The geothermal gradient in Cenozoic sediments is in the range 30 to 40°C/km for most of the area. The calculated temperature at the Moho is 560 and 640°C for surface heat flow values of 63 and 71 mW m−2, respectively. These thermal data are consistent with other geophysical observations for the North China Basin. Relatively high heat flow in this area is related to Late Cretaceous-Paleogene rifting as described in this paper.  相似文献   

11.
Thermal state, rheology and seismicity in the pannonian basin, Hungary   总被引：1，自引：0，他引：1  
On the basis of data on crustal structure and terrestrial heat flow, a 3-D geothermal model for the lithosphere in the Pannonian basin, Hungary, has been calculated. This model, together with information on crustal composition, laboratory data on rock friction, and certain assumptions about fluid conditions and strain-rate levels within the lithosphere, has been used to construct a rheological model of the area.The results obtained show a layered rheological structure where an aseismic part of the crust is “sandwiched” between an upper and a lower seismogenic crustal layers. According to the proposed rheological model, seismic activity in the upper crust may be expected down to depths of 10–12 km, which is confirmed well by the observed depth distribution of seismicity. The model also predicts a lower crustal seismogenic layer down to 20–22 km. Because of infrequent occurrences of deep earthquakes and/or a generally small number of reliable hypocenter depth determinations in the study area, this seismogenic zone is less constrained by observations.The depth of the different rheologic horizons within the crust is governed mainly by thermal conditions. The lower boundary of both seismogenic layers appears isothermal. Brittle-ductile transition in the upper crust coincides with the ˜200 °C isotherm, while in the lower crust it coincides with the ˜ 375 °C isotherm. The lowermost crust and the upper mantle beneath Hungary show ductile behavior, thus the possibility of siesmic activity at these horizons can be excluded.  相似文献   

12.
Hydrothermal alteration zones have been investigated by X-ray diffraction, mineralogical–petrographical techniques, and geochemical analysis. Examination of cores and cuttings from two drill sites, obtained from a depth of about 814–1020 m, show that the hydrothermal minerals occuring in the rock include: K-feldspar, albite, chlorite, alunite, kaolinite, smectite, illite, and opaque minerals.In the studied area, silicified, smectite, illite, alunite, and opal zones have been recognized. These alteration mineral assemblages indicate that there are geothermal fluids, which have temperatures of 150–220°C in the reservoir.The distribution of the hydrothermal minerals shows changes in the chemical composition of the hydrothermal fluid, which are probably due not only to interaction with host rock, but also to dilution of the Na–K–Cl-rich hydrothermal fluid of the deep reservoir by cold sea water at shallow levels. Geochemical analyses of the solid and liquid phases indicate that the hydrothermal fluids of the Tuzla geothermal system are in equilibrium with alteration products.The tectonic structure of the studied area is caused by NW–SE and NE–SW directional forces. The volcanic rocks where hydrothermal zones are observed in the studied area are of Lower–Middle Miocene age comprise latite, andesite, dacite, rhyolite-type lavas, tuff, and ignimbrites.  相似文献   

13.
The centroid-moment tensor solutions of more than 300 earthquakes that occurred in the Himalayas and its vicinity regions during the period of 1977–1996 are examined. The resultant seismic moment tensor components of these earthquakes are estimated. The Burmese arc region shows prominent east–west compression and north–south extension with very little vertical extension. Northeast India and Pamir–Hindu Kush regions show prominent vertical extension and east–west compression. The Indian plate is subducting eastward beneath the northeast India and Burmese arc regions. The overriding Burmese arc has overthrust horizontally with the underthrusting Indian plate at a depth of 20–80 km and below 80 km depth, it has merged with the Indian plate making “Y” shape structure and as a result the aseismic zone has been formed in the region lying between 26°N–28°N and 91.5°E–94°E at a depth of 10–50 km. Similarly, the Indian plate is underthrusting in the western side beneath the Pamir–Hindu Kush region and the overriding Eurasian plate has overthrust it to form a “Y” shape structure at a depth of 10–40 km and below 60 km depth, it has merged with the Indian plate and both the plates are subducting below 60–260 km depth. Further south, the overriding Eurasian plate has come in contact with the Indian plate at a depth of 20–60 km beneath northwest India and Pakistan regions with left lateral strike slip motion.  相似文献   

14.
A geochemical study of thermal and cold springs, stream waters and gas emissions has been carried out in the Mt. Amiata geothermal region.The cold springs and stream waters do not seem to have received significant contribution from hot deep fluids. On the contrary, the thermal springs present complex and not clearly quantifiable interactions with the hot fluids of the main geothermal reservoir.The liquid-dominated systems in the Mt. Amiata area, like most of the high-enthalpy geothermal fields in the world, are characterized by saline, NaCl fluids. The nature of the reservoir rock (carbonatic and anhydritic), and its widespread occurrence in central Italy, favor a regional circulation of “Ca-sulfate” thermal waters, which discharge from its outcrop areas. Waters of this kind, which have been considered recharge waters of the known geothermal fields, dilute, disperse and react with the deep geothermal fluids in the Mt. Amiata area, preventing the use of the main chemical geothermometers for prospecting purposes. The temperatures obtained from the chemical geothermometers vary widely and are generally cooler than temperatures measured in producing wells.Other thermal anomalies in central Italy, apart from those already known, might be masked by the above-mentioned circulation. A better knowledge of deep-fluid chemistry could contribute to the calibration of specific geothermometers for waters from reservoirs in carbonatic rocks.  相似文献   

15.
The Taupo Volcanic Zone (TVZ) of New Zealand is characterised by extensive volcanism and by high rates of magma production. Associated with this volcanism are numerous high-temperature (> 250 °C) geothermal systems through which the natural heat output of 4200 ± 500 MW is channelled. Outside the geothermal fields the heat flow is negligible. The average heat flux from the central 6000 km2 of the TVZ, which contains most of the geothermal fields, is 700 mW/m3. This heat flux appears to be more concentrated along the eastern margin of the TVZ.Schlumberger resistivity measurements (AB/2 of 500 m and 1000 m) have identified 17 distinct geothermal fields with natural heat outputs greater than 20 MW. An additional six, low-heat-output geothermal fields also occur, and may represent formerly more active systems now in decline. Two extinct fields have also been identified. The average spacing between fields is 10–15 km. The distribution of geothermal fields does not appear to be directly associated with individual volcanic features except for the geothermal system that occurs within Lake Taupo and which occupies the vent of the 1800 yr.B.P. Taupo eruption. The positions of the geothermal fields do not appear to have varied for at least the last 200,000 years. These data are consistent with a model of large-scale convection occurring throughout the TVZ, in which the geothermal fields represent the upper portion of the rising, high-temperature, convective plumes. The majority of the recharge to the convection system is provided by the downward movement of cold meteoric water between the fields which suppresses the heat flow in these regions.Gravity measurements indicate that to a depth of about 2.5 km the upper layers of the TVZ consist of low-density pyroclastic infill. A seismic refraction interface with velocity change from 3.2 km/s to 5.5 km/s occurs at a similar depth. The cross-sectional area of the convection plumes (identified electrically) appears to increase at depths of 1–2 km, consistent with a decrease in permeability at the depth at which the velocity and density increase.The seismicity is dominated by swarm activity which accounts for about half of all earthquakes and is highly variable in both space and time. The small number of seismic events (and swarms) that have well determined depths show a cut off of seismicity at depths of 7–9 km. The depth of the transition from brittle to ductile behaviour of the rocks is identified with the transition from a regime where heat is transported by (hydrothermal) convection and pore pressures are near-hydrostatic to a regime where heat transport is dominantly conductive and pore pressures are lithostatic. Within the convective region, temperatures are moderated by the circulation of water so that the depth of the transition from convective to conductive heat transfer can be linked to the bottom of the seismogenic zone. Rocks must become ductile within about 1 km of the bottom of the overlying convective zone.Seismic refraction studies suggest that the crust beneath the TVZ is highly thinned with a seismic velocity of about 7.5 km/ s, typical of the upper mantle, occurring at depth of 15 km. Seismological studies indicate the upper mantle is highly attenuating beneath the TVZ. Conductive heat transfer between the bottom of the convective system, at about 8 km, and the base of the material with crustal velocities, at 15 km, is not able to provide all the heat that is discharged at the surface. Repeated intrusion from the mantle may provide the additional heat transport required.  相似文献   

16.
During 1979–1989, variations were observed in the oxygen composition of the water contained in the geothermal reservoir at Vulcano Island, Italy.The reservoir water, that has a magmatic origin, showed an oxygen composition of +1.0±0.5‰ δ18O during periods without local tectonic earthquakes, and an oxygen composition of +3.4±0.5‰ δ18O after the highest-energy seismic activity that occurred recently near the island. A slight increase of the δ18O value in the reservoir water was also observed after a low-energy sequence of tectonic earthquakes that occurred at very shallow depth just beneath Vulcano Island. These 18O variations in the reservoir water are consistent with earthquake-induced increases in the contribution from high-temperature δ18O-rich magmatic condensate to the geothermal reservoir, and with subsequent decreases in the δ18O value due to 18O exchanges at the temporarily increased reservoir temperature during reactions between the highly reactive magmatic condensate and the local rocks.Only minor changes in the deuterium composition of the reservoir water occurred with time, as the δD value in the magmatic condensate released from the magma after major local earthquakes quickly approached the δD value of the water contained in the geothermal reservoir.Also the chloride concentration in the reservoir water appears to be linked to the contribution from the magmatic fluid. This chloride content seems not to have undergone major changes with time, as it may be buffered by temporary increases in the reservoir temperature up to values >300°C induced by major local earthquakes. This mechanism may possibly occur also in other magmatic–hydrothermal systems.  相似文献   

17.
The Ischia geothermal system is hosted by silicic rocks of the Quaternary Potassic Roman Province, in southern Italy. Exploration drilling down to 1156 m depth in the mid-1950s provided information on boiling profiles (up to 250°C) and on the depth and permeability of the potential reservoirs. Discharge fluid samples were collected and analyzed to define the inflow of surrounding seawater (C1 ranges from 2.5 to 20 g/kg) into the system.Analyses of samples from surface manifestations and shallow wells collected during 1983 and 1988 point to the existence of three distinct mixing regimes, involving three water components. A dishomogeneous body of diluted water (Cl less than 2.5 g/kg), that occurs at depths > 700 m and reequilibrates at 240°C at least, is overlain by an aquifer of groundwater variably mixed with variably seawater (Cl from 4 to 10 g/kg), which tends to reequilibrate at 160°C. Steam-heated waters locally develop and act as dilutants of the rising geothermal fluids.Dilution, mixing, and evaporation of the ascending chloride fluids are supported by oxygen and hydrogen isotopic data the thermal waters being enriched in 18O and D with respect to local meteoric water by up to 7 and 30‰, respectively. The relative composition of the major cations in thermal solutions was used to discriminate the two main groups of thermal waters, the reservoir temperatures of which are estimated from the Na/K-gethermometer. K-Mg geothermometer indicates reequilibration in near-surface conditions.The isotopic composition of the fumarolic steam varies from −7 to −12‰ in ∂8O and from − 35 to − 70‰ in ∂D, in agreement with a deep mixed fluid that boils adiabatically from 240 to 80°C. The deuterium content of the H2O-H2 pair gives enrichment factor of about 830‰, corresponding to equilibrium temperature conditions slightly higher than the surface boiling temperatures. The ∂13C of CO2is almost constant at −4.5‰ (1δ=0.4), suggesting an important magmatic contribution, and the ∂18O values of CO2appears to in equilibrium with accompanying steam at the measured temperatures.The CO2/Ar and H2/Ar chemical ratios have been used to derive aquifer temperatures, the values obtained being consistent with those of solute geothermometers.  相似文献   

18.
The deep well MV5A, drilled in the western part of the Larderello geothermal field, crossed a 20-cm-thick hydraulic fracture breccia unit at a depth of 1090 m below ground level (b.g.l.). This breccia occurs in a fine-grained Triassic metasandstone and consists of angular to subangular clasts of up to some centimeters in size. Pervasive alteration has affected the breccia clasts and wall rock around the breccia, with the formation of Mg–Fe chlorite. After such alteration, hydrothermal circulation caused the precipitation of two generations of calcite cement. Then, ankerite partially replaced these two calcite generations. Ankerite also precipitated in late veinlets with chlorite. Late hydrothermal activity led to the crystallization of albite, quartz and finally, anhydrite. The calcite contains vapor-rich inclusions and two populations of liquid-rich (L1 and L2) inclusions. L1 inclusions are characterized by homogenization temperatures between 304 and 361°C and salinities from 7.4 to 11.6 wt.% NaCl equivalent; L2 inclusions revealed homogenization temperatures in the range of 189–245°C and salinities from 2.6 to 6.3 wt.% NaCl equivalent. The fluids contained in L2 inclusions were probably trapped coevally with some vapor-rich inclusions under boiling conditions after the L1 inclusions formed. Some of the abundant vapor-rich inclusions in calcite may also represent early, low-temperature inclusions affected by decrepitation and/or stretching and/or leaking during L1 trapping. The liquid-rich (L) inclusions trapped at later stages in ankerite, albite and anhydrite display, respectively, homogenization temperature ranges of 189–198°C, 132–145°C, and 139–171°C, and salinities ranging from 1.6 to 1.7 wt.% NaCl equivalent, 1.4 to 2.1 wt.% NaCl equivalent and 3.7 to 6.2 wt.% NaCl equivalent. The inclusions studied record the evolution, over time, of the fluids flowing in the breccia level: L1 inclusions capture high-temperature fluid (about 300 to 350°C) of high salinity (around 10 wt.% NaCl equivalent) at above-hydrostatic pressures (up to about 150 bar). The L2 inclusions in calcite and liquid-rich inclusions in ankerite and albite represent subsequent hydrothermal fluid evolution toward lower temperatures (about 250 to 130°C), pressures (45 to a few bar) and salinities (6.3 to 1.4 wt.% NaCl equivalent). During this stage, boiling processes and infiltration of meteoric waters probably occurred. Finally, moderately saline fluids (around 5 wt.% NaCl equivalent) at a temperature (about 160°C) close to that of present-day in-hole measurements was trapped in the anhydrite inclusions. The liquids trapped in liquid-rich inclusions circulated at 41,000 years (maximum age of calcite) or later. This age represents an upper limit for the development of vapor-dominated condition, in this part of the geothermal system. The fluids circulating at the breccia level were probably meteoric and/or connate waters. These fluids may have interacted with the anhydrite and carbonate bearing formations present in the Larderello area. The occurrence of the hot and saline fluids, trapped in L1 inclusions at above-hydrostatic pressure, suggests that similar fluids but with higher pressure (≥167 bar) and temperature (≥360°C) may have been responsible for rock fracturing.  相似文献   

19.
During ten days of phreatomagmatic activity in early April 1977, two maars formed 13 km behind the Aleutian arc near Peulik volcano on the Alaska Peninsula. They have been named “Ukinrek Maars”, meaning “two holes in the ground” in Yupik Eskimo. The western maar formed at the northwestern end of a low ridge within the first three days and is up to 170 m in diameter and 35 m in depth. The eastern maar formed during the next seven days 600 m east of West Maar at a lower elevation in a shallow saddle on the same ridge and is more circular, up to 300 m in diameter and 70 m in depth. The maars formed in terrain that was heavily glaciated in Pleistocene times. The groundwater contained in the underlying till and silicic volcanics from nearby Peulik volcano controlled the dominantly phreatomagmatic course of the eruption.During the eruptions, steam and ash clouds reached maximum heights of about 6 km and a thin blanket of fine ash was deposited north and east of the vents up to a distance of at least 160 km. Magma started to pool on the floor of East Maar after four days of intense phreatomagmatic activity.The new melt is a weakly undersaturated alkali olivine basalt (Ne = 1.2%) showing some transitional character toward high-alumina basalts. The chemistry, an anomaly in the tholeitic basalt-andesite-dominated Aleutian arc, suggests that the new melt is primitive, generated at a depth of 80 km or greater by a low degree of partial melting of garnet peridotite mantle with little subsequent fractionization during transport.The Pacific plate subduction zone lies at a depth of 150 km beneath the maars. Their position appears to be tectonically controlled by a major regional fault, the Bruin Bay fault, and its intersection with cross-arc structural features. We favor a model for the emplacement of the Ukinrek Maars that does not link the Ukinrek conduit to the plumbing system of nearby Peulik volcano. The Ukinrek eruptions probably represent a genetically distinct magma pulse originating at asthenospheric depths beneath the continental lithosphere.  相似文献   

20.
Silica chimneys were discovered in 1985 at 86°W in the rift valley of the Galapagos Spreading Center at 2600 m depth (“Cauliflower Garden”). The inactive chimneys lack any sulfides and consist almost entirely of amorphous silica (up to 96 wt.% SiO2, opal-A); Fe and Mn oxides are minor constituents. Oxygen isotope data show that formation of the silica chimneys took place at temperatures between 32°C (+29.9‰ δ18O) and 42°C (+27.8‰ δ18O).Th/Udating reveals a maximum age of 1440 ± 300y. Amorphous silica solubility relations indicate that the silica chimneys were formed by conductive cooling of pure hydrothermal fluids or by conductive cooling of a fluid/seawater mixture. Assuming equilibrium with quartz at 500 bars, initial fluid temperatures of more than 175°C (i.e., a concentration of > 182 ppm SiO2) were required to achieve sufficient supersaturation for the deposition of amorphous silica at 40°C and 260 bars. If the silica chimneys originate from the same or a similar fluid as higher-temperature ( < 300°C) sulfide-silica precipitates found nearby (i.e., 2.5 km away), then subsurface deposition of sulfides may have occurred.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号