共查询到20条相似文献，搜索用时 703 毫秒
1.
李思庄滑坡为河北省顺平县境内潜在危险性最大的一残坡积堆积层滑坡,近年由于削坡建房,滑坡稳定性降低,极端降雨条件下存在复活可能。在野外调查确定滑坡结构特征的基础上,采用改进Mein-Larson降雨入渗模型分析不同降雨强度及持时对李思庄滑坡安全系数影响,运用有限差分软件FLAC3D计算分析该滑坡在天然和极端降雨工况下的稳定状态。研究结果表明:天然状态下,边坡潜在滑移面为基岩与残坡积层分界面,边坡安全系数为1.18,未发生失稳破坏;随降雨历时增加,潜在滑移面由基岩与残坡积层分界面转移到湿润峰面,当湿润峰达到基岩与残坡积层分界面,边坡安全系数为0.83,属不稳定状态。并对李思庄滑坡初步提出设置挡土墙和截排水沟的治理建议。 相似文献
2.
某水电站坝前堆积体稳定性的三维数值模拟分析 总被引：13，自引：0，他引：13
某水电站坝前堆积体边坡的稳定性关系到该大坝的建设与运营。野外工作发现,它是深切冲沟型崩塌式堆积体,由下伏基岩和松散的堆积物组成。在1 360~1 450 m高程之间堆积体有一个较为明显的收口转向特征,这有利于增加其稳定性。在野外工作的基础上,采用目前较为通用的两种三维有限元软件(3D-Sigma和3D-Flac)对其稳定性进行数值模拟研究。结果表明：（1）堆积体的应力场主要表现为以自重应力场为主,其应力分布主要受岩性控制;（2）堆积体的潜在滑动面为堆积体与其下伏基岩接触部位的一定范围内;（3）堆积体的位移表现为向坡外(临空面方向)滑移,且中前缘的位移量相对较大;（4）堆积体前缘的收口效应改善了其应力状态,增加了稳定性;（5）堆积体的整体稳定性较好,在1 472~1 610 m高程之间的堆积体有可能发生局部的中浅层破坏。 相似文献
3.
汶川特大地震中山岭隧道变形破坏特征及影响因素分析 总被引：22，自引：0，他引：22
汶川大地震造成位于震中附近的都江堰-汶川公路多座隧道严重受损。本文通过现场调研、资料收集与分析,将地震区山岭隧道变形破坏的基本类型概括为洞口边坡崩塌与滑塌、洞门裂损、衬砌及围岩坍塌、衬砌开裂及错位、底板开裂及隆起、初期支护变形及开裂等。分析其影响因素,认为发震断裂的次级断层、基覆界面、洞口不稳定斜坡、高地应力环境下的软弱围岩对隧道强烈震害具有控制作用。以汶川地震给予隧道抗震的启示,建议强震区的山岭隧道应将洞口边坡防护、洞口明洞和洞门结构作为一个系统进行综合设计,在条件允许的情况下尽可能采用削竹式洞门结构;隧道穿越活动断裂带的次级断层时在其两侧一定范围内二次衬砌应采用钢筋混凝土结构;基覆界面、围岩软岩与硬岩之间的过渡地带、围岩质量突变地带等应采用改善围岩力学性质且让其渐变的措施进行处理。 相似文献
4.
甘肃有色地勘局106队部东侧的不稳定斜坡位于兰州市九州开发区黄河北岸、罗锅沟左岸沟谷斜坡地带。勘查查明,不稳定斜坡中下部及坡脚地带为古近系砂质泥岩,斜坡中上部和坡顶为第四系全新统人工堆积物;其形成原因与地形地貌、地质构造、工程地质特征、降雨、地下水、人类工程活动等有关。根据定性分析和定量计算,认为勘查区斜坡现状处于不稳定状态,其失稳产生崩塌、滑坡的可能性大,最危险滑裂面位于填土和基岩的接触面;拟建工程建设遭受其危害的可能性及危险性中等。建议在治理斜坡时,坡脚挡土墙工程选用浅基础型式,跨越浅沟段(15m)可采用桩基础形式,以砂质泥岩作为基础持力层,并严格防止地表水渗入砂质泥岩地基。为区内不稳定斜坡的治理,防灾减灾提供了依据。 相似文献
5.
The Sharm El-Sheikh/Ras-Nasrani area is one of the most attractive tourist resorts in Egypt particularly and in the world
in general. The area has been rapidly growing during the last few years. Many construction projects including villages, hotels,
beaches, and roads have recently been undertaken. The following study demonstrates the use of high-resolution satellite images,
QuickBird imagery, acquired on June 2nd, 2007 (0.61 m spatial resolution), for detailed mapping of the recent developments
and the slope instability hazard zones. The results were confirmed by field reconnaissance. Our findings indicate that there
are many development areas threatened by unstable zones. The hazard areas have been delineated and classified, and a final
slope instability hazard map has been established. Different factors were found to have a crucial impact on the slope instability,
some natural and others man-made. These unstable localities need to be remediated and/or monitored to avoid any loss in property
and/or lives. 相似文献
6.
A study of the indoor radon gas levels was performed in 935 homes in Scania, southernmost Sweden, located on geologically different ground with regard to uranium (U) content. In one of these two areas the bedrock consists of alum shale with U contents exceeding 200 ppm. In the other area there is no U-rich bedrock. Indoor radon levels are influenced by U content and permeability as shown below.For maam nancy for table, please place here. Thanx!The results show that the indoor radon levels were highest in homes located on bedrock with medium to high U content combined with a highly permeable drift covering the bedrock. The difference was statistically significant(P < 0.0001). Other results of the investigation are: 14 homes built from aerated concrete made from U-rich alum shale had higher levels than 767 homes with walls from other material (312 vs 106 Bq/m3;P = 0.0011); 242 homes with a cellar had lower radon levels than 563 without (62 vs 138 Bq/m3;P <0.0001); further, 418 homes with private well had higher levels than 360 with public water supply (140 vs 82 Bq/m3;P <0.0001). The results of the investigation show a profound effect of a combination of high bedrock U content and high cover permeability. The effect of the uraniferous drift on the indoor radon levels is evident. Thus, the geological conditions should be carefully considered when screening for high-risk buildings, as well as when planning for new ones. Also, the construction of the building and its water supply have some influence. 相似文献
7.
西南某大型水电站拱肩槽边坡开挖的变形响应研究 总被引：1，自引：0，他引：1
对在复杂地质条件和高地应力环境下,高达近330m的人工岩石拱肩槽高边坡的研究,尤其是在大坡比、强开挖条件下所表现的变形响应规律的研究具有重要的理论与现实意义。论文通过大量现场跟踪施工的地质调查工作和利用丰富的监测资料的基础上,系统地研究了此类边坡变形响应的基本规律及特殊表现,得到了拱肩槽高边坡开挖过程中,边坡的变形与开挖过程有较强的同步性。变形主要受开挖卸荷影响;随开挖的进行,坡体的变形随开挖面的远离表现出总体衰减的特征等。开挖后的坡体的变形量较小,变形深度较浅,而且在开挖12~18个月后,变形趋于稳定。这些结论对类似边坡开挖及其稳定性的控制具有重要的借鉴意义。 相似文献
8.
9.
重庆某不稳定斜坡变形监测及稳定性分析 总被引：2，自引：0，他引：2
位于重庆市区的某不稳定斜坡, 其变形区范围内拟进行大规模基坑开挖, 为保证安全施工, 必须准确评价斜坡的稳定性.在现场调查、归纳地质环境条件的基础上, 对不稳定斜坡进行变形监测, 研究斜坡变形特征; 采用FLAC-3D有限差分软件进行数值模拟分析, 将结果与实际变形监测曲线进行对比、拟合, 得到监测点的位移情况, 从而准确了解不稳定斜坡的变形情况; 最后基于极限平衡法和FLAC-3D强度折减法对不稳定斜坡天然状况以及基坑开挖工况下的稳定性进行评价. 相似文献
10.
R. C. Lindholm 《Environmental Geology》1994,23(4):271-275
Soil maps can be used to generate maps showing the areal distribution of bedrock. This technique is especially useful in heavily vegetated areas where weathering is intense and outcrops sparse. Broad lithologic categories that are readily distinguished include: diabase/basalt, sandstone, shale, limestone, conglomerate, and hornfels. Using soil maps is not a substitute for field work, but is a valuable tool to aid in making geologic maps. Soil maps can also be used to produce derivative maps showing slope steepness and landslide distribution. 相似文献
11.
倾斜基岩上的边坡破坏模式和稳定性分析 总被引：6，自引：0，他引：6
应用离心模型试验对工程中被颇为关注的带有与边坡走向一致的倾斜基岩面,且在该基岩面存在软弱夹层的边坡的稳定性和破坏模式进行了比较详细地研究,并用极限平衡分析方法对试验结果进行了计算分析。模型试验结果表明,该类边坡失稳时,紧贴岩面的软弱夹层就成为滑动破坏面,因而边坡整体沿基岩面向下滑动,且侧向水平位移各处基本一致,表现出典型的平移滑动破坏模式。将稳定安全系数的实测结果与按平移滑动破坏模式的极限平衡分析方法的计算结果相比较后发现,两者相当地吻合,证实了按平移滑动破坏模式所作的极限平衡分析,能良好地预测边坡平移滑动破坏情形下的稳定安全系数。 相似文献
12.
13.
Two‐dimensional slope stability analysis for a slope with a row of drilled shafts needs a mechanism to take into account the three‐dimensional effect of the soil arching due to the spaced drilled shafts on slope. To gain a better understanding of the arching mechanisms in a slope with evenly spaced drilled shafts socketed into a stable stratum (or a rock layer), the three‐dimensional finite element modelling technique was used for a comprehensive parametric study, where the nonlinear and plastic nature of the soil and the elastic behavior of the drilled shafts as well as the interface frictions were modelled. Various factors were varied in the parametric study to include (1) the rigidity of the drilled shafts as influenced by its diameter, modulus of elasticity, and total length; (2) shafts spacing and location on the slope; (3) the material properties of rock and the socket length of shaft; and (4) the soil movement and strength parameters. Evidences of soil arching and reduction in the stresses and displacements through the load transfer mechanisms due to the presence of the drilled shafts were elucidated through the finite element method (FEM) simulation results. Design charts based on regression analysis of FEM simulation results were created to obtain a numerical value of the load transfer factor for the arching mechanism provided by the drilled shafts on the slope. Observations of the arching behavior learned from the FEM simulations provide an insight into the behavior of drilled shafts stabilized slope. Copyright © 2009 John Wiley & Sons, Ltd. 相似文献
14.
Comparative analysis of contributing parameters for rainfall-triggered landslides in the Lesser Himalaya of Nepal 总被引：6，自引：0，他引：6
Ranjan Kumar Dahal Shuichi Hasegawa Minoru Yamanaka Santosh Dhakal Netra Prakash Bhandary Ryuichi Yatabe 《Environmental Geology》2009,58(3):567-586
In the Himalaya, people live in widely spread settlements and suffer more from landslides than from any other type of natural
disaster. The intense summer monsoons are the main factor in triggering landslides. However, the relations between landslides
and slope hydrology have not been a focal topic in Himalayan landslide research. This paper deals with the contributing parameters
for the rainfall-triggered landslides which occurred during an extreme monsoon rainfall event on 23 July 2002, in the south-western
hills of Kathmandu valley, in the Lesser Himalaya, Nepal. Parameters such as bedrock geology, geomorphology, geotechnical
properties of soil, and clay mineralogy are described in this paper. Landslide modeling was performed in SEEP/W and SLOPE/W
to understand the relationship of pore water pressure variations in soil layers and to determine the spatial variation of
landslide occurrence. Soil characteristics, low angle of internal friction of fines in soil, medium range of soil permeability,
presence of clay minerals in soil, bedrock hydrogeology, and human intervention were found to be the main contributing parameters
for slope failures in the region. 相似文献
15.
16.
顺层岩质斜坡是沉积岩地区常见的一种斜坡类型,也是各种工程建设重点关注的一类斜坡。以川西雅安地区典型的顺层岩质斜坡为例,采用现场调查、无人机测绘、钻探、物探和稳定性计算等技术方法,归纳总结目前斜坡存在的变形破坏模式。分析计算斜坡在不同工况条件下,层间破碎带连通率与斜坡稳定性之间的关系。研究结果表明:层间破碎带对斜坡稳定性具有重要的影响或控制作用,当斜坡浅表部强风化岩体内层间破碎带连通率小于86%时,斜坡稳定性与现状调查结果吻合。研究结果对川西地区基础设施规划建设和防灾减灾具有重要的工程意义。 相似文献
17.
Applicability of piezocone and dilatometer to characterize the soils of the Venice Lagoon 总被引：1，自引：0，他引：1
Giuseppe Ricceri Paolo Simonini Simonetta Cola 《Geotechnical and Geological Engineering》2002,20(2):89-121
The effectiveness of two geotechnical investigation tools—the piezocone and the dilatometer—to characterize the soils forming the shallowest deposits of the upper quaternary basin of the Venice lagoon soil is examined in this study. For this purpose, the results of a comprehensive site and laboratory investigation carried out recently over a small lagoon area—the Malamocco Test Site—are used to evaluate the applicability of the most widely used charts or correlative equations to characterize soil profile and estimate the main geotechnical properties of these soils, when applied to the interpretation of CPTU and DMT results. The particular interest of this site—apart from its unquestionable historical relevance—is the presence, apparently without any regular pattern in depth and site, of a predominantly silty fraction combined with clay and/or sand, thus forming an erratic interbedding of various types of sediments. This case represents therefore the opposite condition of that which has been normally utilized in the past to calibrate the two devices, namely the presence of particularly homogeneous natural deposits or artificially sedimented homogeneous layers of sand or clay. The Malamocco Test Site may therefore be considered as test benchmark for the applicability of the two devices to characterize highly heterogeneous silty deposits. 相似文献
18.
On August 19–20, 1969, the heavy rainfall associated with hurricane Camille triggered numerous debris avalanches in the Blue Ridge Province of central Virginia. Most slope movements occurred in Nelson County in an area that is predominantly underlain by Precambrian granites, gneisses, and schists. This study was undertaken to determine which geotechnical properties of soil and rock were important in promoting debris avalanche activity in central Virginia.
Twenty-one first-order drainage basins in Nelson County were randomly selected and classified as unstable based on their values of horizontal curvature and average gradient as measured on topographic maps. Slope orientation, total soil thickness, and soil horizon thicknesses were measured in the field. Soils from the study basins were tested for geotechnical properties including natural water content, grain-size distribution, Atterberg limits,in situ dry density, and shear strength. These geomorphic and geotechnical properties were subsequently analyzed to ascertain what significant differences existed at the 99% confidence level between three failure classes of unstable basins. Where rock outcrops were present, information regarding discontinuity type, orientation, spacing, continuity, roughness, waviness, aperture, and water quantity was obtained. Values of hand sample hardness were also procured. The role of these bedrock characteristics in determining unstable basin failure class was statistically analyzed at the 95% confidence level.
In general, the results indicate that basins classified as geomorphically unstable are particularly susceptible to debris avalanche activity if they contain coarse-grained soils with low values of plasticity index and moisture content. Geotechnical properties are also found to be significantly different when analyzed with respect to the underlying bedrock unit, which helps explain why basins underlain by certain bedrock units failed more often than basins underlain by other bedrock units. Differences in topography, due to the nature of the underlying bedrock unit, also explain the frequency of debris avalanche occurrences in a given bedrock unit. Characteristics of bedrock discontinuities do not appear to have influenced drainage basin failure. 相似文献
19.