共查询到20条相似文献，搜索用时 265 毫秒
1.
选取广西容县花岗岩残积土为研究对象,取击实曲线上3个不同含水率对应的压实样（最佳含水率及干侧、湿侧,后两者对应的干密度相同）分别进行了直剪试验、扫描电镜观测（SEM）和压汞试验（MIP）,并从微观特征解释其力学性能的差异。结果表明:（1）花岗岩残积土在3种压实状态下具有相同应力-应变曲线形状,无明显峰值,抗剪强度在最佳状态时的最高,湿侧状态抗剪强度与干侧状态相近,3种状态下内摩擦角值差别较小,但黏聚力在最佳状态时最大,干侧和湿侧状态较最佳状态分别下降66.4%和43.1%;（2）花岗岩残积土在湿侧状态下普遍形成团聚体,团聚体之间呈架空结构,累积孔隙体积最大,为明显的双峰分布孔隙特征;在最佳状态下组构最密,高岭石片定向性排列;在干侧状态下高岭石片呈片架结构,累积孔隙体积最小;随着含水率的降低,土样双峰孔隙特征逐渐变得不明显;（3）花岗岩残积土在不同状态时的微观特性较好地解释其力学性质的差异。 相似文献
2.
Strength properties of compacted ash layers depend to a great extent on the moulding conditions. This paper focuses on the effects of compaction energy and degree of saturation on strength characteristics of compacted pond ash. The pond ash sample, collected from the ash pond of Rourkela Steel Plant (RSP), was subjected to compactive energies varying from 357 kJ/m3 to 3488 kJ/m3. The optimum moisture content and maximum dry densities corresponding to different compactive energies were determined by conventional compaction tests. The shear strength parameters, unconfined compressive strengths (UCS) and California bearing ratio (CBR) values of specimens compacted to different dry densities and moisture content were assessed and reported. The effects of compaction energy and degree of saturation on shear strength parameters i.e. unit cohesion (cu) and angle of internal friction (Ф) values and also the UCS values are evaluated and presented herein. The results indicate that the dry density and strength of the compacted pond ash can be suitably modified by controlling the compactive energy and moulding moisture content. The strength achieved in the present study is comparable to the good quality, similar graded conventional earth materials. Hence, it may be safely concluded that pond ash can replace the natural earth materials in geotechnical constructions. 相似文献
3.
广西红粘土击实样强度特性与胀缩性能 总被引：15，自引：0，他引：15
通过对广西贵港红粘土重型击实样的室内试验研究,探讨了其力学特性、胀缩性能、孔径分布特征与含水量之间的关系。结果表明：干密度指标总体上能反映红粘土击实样的强度规律,但非饱和击实样强度峰值对应的含水量因基质吸力作用而偏小,饱和后土体由于吸水膨胀与基质吸力的消失,使得强度峰值对应含水量较饱和前明显增大,红粘土在最优含水量下压实,虽可获得很高的压实度,但饱和后的强度并非最大;红粘土击实样的胀缩性能主要由含水量决定,同时,受到干密度的影响;孔隙主要以孔径在0.01～0.05μm范围内的小孔隙为主,为进一步掌握红粘土的工程力学特性提供了帮助。 相似文献
4.
吸力、含水率和干密度对重塑非饱和土抗剪强度影响研究 总被引：13，自引：0，他引：13
进行了一系列控制吸力、含水率和干密度的直剪试验,研究了重塑非饱和土的抗剪强度特性。试验结果表明,在试验研究的吸力范围内,非饱和土的黏聚力随吸力线性增加,而内摩擦角随吸力的变化则很小。对于控制含水率的试验,非饱和土的黏聚力和内摩擦角均随含水率增加而线性减小,且黏聚力减小的幅度更明显。干密度对非饱和土的内摩擦角几乎没有影响,黏聚力随干密度呈指数增加。对控制吸力和含水率的试验结果进行了比较,提出的考虑含水率影响的抗剪强度公式可供实际工程参考。 相似文献
5.
为研究湿热多雨气候条件诱发的干湿循环过程对红黏土长期性能的影响规律,对制样过程中干湿循环含水率变化幅度控制技术进行改进,制备不同干湿循环次数以及含水率变化幅度试样。利用固结排水三轴剪切与压缩试验,研究了干湿循环次数与干湿循环含水率变化幅度对压实红黏土工程性状的影响规律。结果表明,压实红黏土的黏聚力 与内摩擦角 均随干湿循环次数 的增加而衰减,首次干湿循环之后衰减效应最显著,其后较弱并趋于稳定, 的衰减程度小于c,且在低围压下的抗剪强度随干湿循环衰减更加显著;压缩模量E1-2随N的总体衰减规律与强度参数类似,但衰减幅度小于c而大于 ;随着干湿循环含水率变化幅度增大,压实红黏土c与E1-2略有减小, 基本不变,压实红黏土含水率在 4%变化范围内,具有相对稳定的力学特性。该研究表明,红黏土不宜直接用于填筑路床与边坡表层的填料,可以作为上下路堤堤心的填料,但必须采取防排水工程措施与边坡防护措施。 相似文献
6.
冻融循环对砼护坡界面抗剪强度影响试验研究 总被引：1，自引：1，他引：0
以混凝土铰接块+土工布+黏土护坡结构室内模型为研究对象, 分别讨论不同含水量及冻融循环次数下接触面间抗剪强度指标的变化规律. 分别测定常温下护坡结构含水量在15.7%~28%之间的黏聚力(C)和内摩擦角(φ)值, 含水量为18%以及饱和状态下经过10次冻融循环的C值和φ值, 采用多元回归法进行分析. 结果表明: 含水量对护坡结构的抗剪强度指标弱化十分明显, 斜面摩擦试验中黏聚力和内摩擦角均随含水量增加而降低; 含水量与内摩擦角呈线性相关关系, 与黏聚力呈乘幂关系. 冻融循环过程水分迁移导致砼护坡界面水分增大, 界面抗剪强度指标弱化. 随冻融循环次数的增加砼铰接块护坡界面的抗剪强度减小, 对于非饱和黏性土, 在5次冻融循环时减小幅度较大, 但10次冻融循环时减小幅度较小并基本趋于稳定; 而对于饱和黏性土, 其抗剪强度指标随冻融循环次数的增加减小幅度并不明显. 相似文献
7.
Delineation of compaction criteria for acceptable hydraulic conductivity of lateritic soil-bentonite mixtures designed as landfill liners 总被引：2，自引：1，他引：1
In current geoenvironmental practice, design engineers usually require that soil liners in waste landfills be compacted within a specified range of water content and dry unit weight. This specification is based primarily on the need to achieve a minimum dry unit weight for factors controlling the performance of compacted soil liners most especially the hydraulic conductivity, k. In this study, lateritic soil treated with up to 10% bentonite, prepared at various compaction states (dry of optimum, optimum and wet of optimum moisture content) was compacted with four compactive efforts (i.e., the reduced British Standard Light, British Standard Light, West African Standard, and British Standard Heavy) to simulate the range of compaction energies expected in the field. Prepared soil mixtures were permeated with water and specimens that yielded the permissible limit of k????1?×?10?9?m/s were enclosed in an envelope (known as the acceptable zone) on the water content?Cdry unit weight curve. It was observed that compaction conditions resulting in moisture content slightly wet of optimum led to the lowest values of k and that the shapes and boundaries of the acceptable zones gradually increased in extent, shifting to wet side of optimum moisture content as the bentonite content increased to 10%. This approach provides good control over the quality of compacted soils and has great potential for field application. 相似文献
8.
黏粒含量对黄土抗剪强度影响试验 总被引：1，自引：0，他引：1
开展不同黏粒含量对黄土抗剪强度影响的试验研究,揭示黏粒含量对抗剪强度的影响及其微观机理,为黄土地区的工程实践提供科学依据。通过自制负压湿筛装置筛取不同黏粒含量的黄土试样,采用静压法将不同黏粒含量的黄土试样制成同一干密度不同含水率试样进行直剪试验。研究表明:随着含水率的增长,不同黏粒含量试样黏聚力均表现为先增加后减小的变化规律,并在含水率14%附近达到最大值;内摩擦角则均呈单调下降的变化趋势。随黏粒含量的增长,不同含水率试样黏聚力呈增大趋势;内摩擦角呈先减小后增加的变化趋势。通过其微观结构可解释黏粒含量对黄土抗剪强度的影响机制。 相似文献
9.
含水率及干密度对桂林红黏土抗剪强度的影响 总被引：1，自引：0，他引：1
为研究含水率及干密度对桂林红黏土抗剪强度的影响机理,进行了一系列控制含水率、干密度的直剪试验,建立含水率及干密度与抗剪强度的函数关系式。试验结果表明:同一干密度条件下,粘聚力、内摩擦角随含水率的增大整体呈下降趋势;在含水率相同时,随干密度增大,粘聚力减小,内摩擦角增大。分析表明:随含水率增大,具有“水稳定”性的胶结作用减弱,引起粘聚力降低;土中结晶态氧化铁含量高于胶结态时,内摩擦角增大,反之则降低。干密度增大时,重塑土因胶结键断裂后短时间无法恢复,使土颗粒的有效胶结面积的减少程度大于其增多的程度,引起粘聚力下降;干密度的增大会改变红黏土的微观结构模型,土中封闭孔隙的增多会导致粘聚力下降;土样微观结构性随干密度的增大而增强,使内摩擦角增大。 相似文献
10.
非饱和压实黄土结构特性试验研究 总被引：1，自引：0，他引：1
对增（减）湿到相同含水率及相同干密度的不同结构性非饱和压实黄土进行土-水特征曲线试验和三轴剪切试验,研究制样含水率引起的结构变化对非饱和压实黄土基质吸力、应力-应变特征及结构性参数的影响。研究结果表明：制样含水率引起的结构性对非饱和压实黄土的土-水特征曲线有明显的影响,小于塑限时基质吸力随制样含水率的增大而增大,最优制样含水率时非饱和压实黄土具有均匀小孔隙的团粒凝聚结构使其吸力相对最大;应力-应变曲线在最优结构状态时位于坐标最上端,小于最优制样含水率时的结构弱化程度相对较低,其应力-应变曲线逐渐下移,大于最优制样含水率时土样的结构弱化程度较高,其应力-应变曲线位于最下端;定义的结构性参数m?r能够合理反映压实黄土的结构性,弥补了压实土工程中用最优含水率和最大干密度指标无法反映土结构性影响的不足;屈服结构性参数m?r0能够合理反映出不同制样含水率压实黄土的结构弱化程度,结构弱化程度还反映在三轴剪切破坏强度上。 相似文献
11.
为研究高填方路堤压实土率相关变形特征,对不同压实度的非饱和压实土分别开展了不同加载速率以及不同围压条件下的CD三轴剪切试验,探讨了不同工况下压实土的剪切强度指标;借助GDS饱和土静态三轴仪的围压控制器来间接测定非饱和压实土体变的途径。试验结果表明：压实土强度及变形特征具有明显的时间相依性,加载速率越大,压实土的抗剪强度越高,超固结变形特性越强,抗剪强度指标黏聚力c值增幅较大、内摩擦角 值增幅较小;低围压下,压实土呈应变软化及剪胀变形,且压实度越高,应变软化及剪胀变形越显著,c值增加明显、 值增加缓慢。采用基于下负荷面的弹黏塑性本构模型对路基压实土的率相关变形特征进行表征,预测结果与试验数据吻合良好,表明该模型适用于高填方路堤长期沉降分析。 相似文献
12.
Summary In many parts of the world, particularly in humid tropical regions, residual soils are abundant. In this paper the suitability of a residual lateritic soil as a construction material is investigated, with respect to its strength and compaction characteristics. In comparison with other typical construction fills available in Southeast Asia, compacted lateritic soils produce excellent shear strengths and CBR values. However, the brittleness and tensile cracking of this compacted material become enhanced on the dry side of the optimum moisture content, or if excessive compaction is imparted. Nevertheless, at a moisture content of 2% wetter than the optimum, the tensile mode of failure is suppressed and the lateritic fills become ideally suited for the construction of high embankments and impervious dam cores. 相似文献
13.
Osman Sivrikaya 《Environmental Geology》2008,53(7):1585-1595
To prevent the leakage of pollutant liquids into groundwater and sublayers, the compacted fine-grained soils are commonly
utilized as mineral liners or a sealing system constructed under municipal solid waste and other containment hazardous materials.
This study presents the correlation equations of the compaction parameters required for construction of a mineral liner system.
The determination of the characteristic compaction parameters, maximum dry unit weight (γ
dmax) and optimum water content (w
opt) requires considerable time and great effort. In this study, empirical models are described and examined to find which of
the index properties correlate well with the compaction characteristics for estimating γ
dmax and w
opt of fine-grained soils at the standard compactive effort. The compaction data are correlated with different combinations of
gravel content (G), sand content (S), fine-grained content (FC = clay + silt), plasticity index (I
p), liquid limit (w
L) and plastic limit (w
P) by performing multilinear regression (MLR) analyses. The obtained correlations with statistical parameters are presented
and compared with the previous studies. It is found that the maximum dry unit weight and optimum water content have a considerably
good correlation with plastic limit in comparison with liquid limit and plasticity index. 相似文献
14.
安哥拉Quelo砂抗剪强度特性试验研究 总被引：1，自引：0，他引：1
基于安哥拉Quelo（Muceque）砂原状土和重塑土的直剪试验,探讨了结构性、含水率、干密度对Quelo砂抗剪强度的影响。试验结果表明,结构性对Quelo砂的抗剪强度影响较为复杂,原状土与重塑土的抗剪力学指标具有明显差异;Quelo砂遇水软化特性显著,原状土和重塑土的黏聚力和内摩擦角随含水率的增大近似呈对数衰减;Quelo砂级配良好,压实后抗剪强度高,适宜用作回填材料,重塑土的黏聚力随干密度的增大近似呈线性增大,内摩擦角随干密度的增大分为稳定段和增大段,呈分段函数的特征。 相似文献
15.
M. Mirzababaei M. Miraftab M. Mohamed P. McMahon 《Geotechnical and Geological Engineering》2013,31(1):173-182
Municipalities and recycling and environmental authorities are concerned about the growing amount of carpet waste produced by household, commercial and industrial sectors. It is reported that 500,000 tonnes of carpet waste fibre are plunged into landfills annually in the UK. In the United States of America, around 10 million tonnes of textile waste was generated in 2003. In geotechnical engineering, expansive clay soils are categorised as problematic soils due to their swelling behaviour upon increase in the moisture content. The problematic nature of such soils is intensified with the increase in the plasticity index. This paper presents results of a comprehensive investigation into utilisation of carpet waste fibres in order to improve the swelling characteristics of compacted cohesive soils. Therefore, two different clay soils with markedly different plasticity indices (i.e. 17.0 and 31.5 %) were treated with two different types of carpet waste fibre. Waste fibres were added to prepare specimens with fibre content of 1, 3 and 5 % by dry weight of soil. Soil specimens with different dry unit weights and moisture contents were prepared so as to the swelling behaviour of fibre reinforced compacted clays is completely attained under various scenarios. The results indicated that the behaviour of the fibre reinforced soils seems highly dependent on the initial compaction state and secondary on the moisture content. It was found that the swelling pressure drops rapidly as the percentage of fibre increases in samples prepared at the maximum dry unit weight and optimum moisture content. Reducing the dry unit weight, while maintaining constant moisture content or increasing the moisture content at constant dry unit weight was found to reduce the swelling pressure. 相似文献
16.
为探究了解桂林重塑红黏土抗剪强度特性,利用三轴试验研究饱和及未饱和重塑红黏土的干密度、含水率对土体抗剪强度的影响。试验结果表明:相同最优含水率下的饱和重塑红黏土的黏聚力与干密度的二次多项式拟合曲线呈凹状,未饱和土的黏聚力与干密度的二次多项式拟合曲线呈凸状,两者黏聚力曲线在1.41 g ·cm-3附近两者差值最大;饱和重塑红黏土的内摩擦角与干密度的二次多项式拟合曲线呈凹状,未饱和土的内摩擦角与干密度的二次多项式拟合曲线呈凸状,两者在干密度为1.35 g ·cm-3附近差值最大;未饱和重塑红黏土的含水率对抗剪强度参数影响显著。 相似文献
17.
广西红黏土分布区柴油泄漏对土体造成了一定程度污染,为研究轻质非水相非极性柴油孔隙液对红黏土力学性质的影响,本文以0#柴油为添加剂对其重塑样进行不排水快速直剪试验,测得了不同含水率、含油率、法向压力下红黏土抗剪强度及其参数变化规律。研究结果表明:在土-水-油系统中,非极性柴油孔隙液对红黏土强度影响相对较小,且受含水率影响。同一含油率时,红黏土抗剪强度、内摩擦角、黏聚力均随含水率增加而降低;同一含水率时,法向压力影响柴油作用模式,随含油率增加,抗剪强度参数变化较为复杂,当含水率为20%,红黏土内摩擦角、黏聚力反向波动变化;同一含湿率时,柴油比例的提高导致红黏土抗剪强度参数的增大。扫描电镜观察发现,非极性柴油孔隙液的介入,改变了水-土系统的静电及结构模式,导致红黏土强度发生变化,通过所建的“多尺度多阶段柴油作用微结构模型”,阐明了柴油孔隙液对红黏土强度特性影响的微观机理。 相似文献
18.
分散性土的抗剪强度特性试验研究 总被引：2，自引：0，他引：2
分散性土是一种具有特殊工程性质的土,其典型的性质为抗渗性能差,耐冲蚀能力低,在纯水中具有很高的分散性。目前,人们对于分散性土的研究主要集中在鉴定、抗渗和改良等方面,而对其抗剪强度特性的研究很少。采用三轴CU试验研究不同初始条件下分散性土的抗剪强度特性。结果表明:分散性土的应力-应变曲线在小围压、低含水率和高干密度的状态下呈应变软化型,在围压较大、含水率较高的情况下呈弱硬化型或硬化型;黏聚力和内摩擦角均随含水率的增大而减小,并且干密度越大受水分影响越强烈;黏聚力随干密度的增大而增大,在低含水条件下,黏聚力的增幅较大,而在高含水条件下,黏聚力的增幅则较小;内摩擦角随干密度的增大有少量增大。 相似文献
19.
对添加了纳米石墨粉的红黏土以击实进行了重塑样制备,设计了不同掺量纳米石墨粉在红黏土最优含水率下的三轴固结不排水试验;通过应力-应变曲线,分析了不同掺量纳米石墨粉对红黏土力学性能的影响,得出了抗剪强度和抗剪强度指标的规律,并采用SEM微观手段对其改善机理进行了分析。试验结果表明:抗剪强度和黏聚力C随纳米石墨粉掺量的增加先增加后减小,内摩擦角$\varphi $基本保持不变,得出适量的纳米石墨粉对红黏土的力学性质有显著的提高,最优掺量在1%~2%之间。研究认为,纳米石墨粉红黏土呈现出的力学性质,与纳米石墨粉对红黏土孔隙结构的影响、纳米石墨粉对红黏土颗粒的黏附胶结密切相关。 相似文献
20.
由于室内剪切试验结果存在试样结构性扰动和尺寸效应等带来的不确定性问题,且以往的常规原位大型剪切试验是针对天然状态土体,不能获得饱和土体的强度参数,导致岩土结构稳定性分析和工程设计中大多采用反演方法求取强度参数,而很少直接运用这些试验参数.在本次试验方法研究中,试验仪器仍然采用常规的天然土体原位大型剪切试验仪器,针对土体饱和问题,设计了“制样后饱和法”和“饱和后制样法”2种浸水饱和装置,并采用这2套装置在甘肃省黑方台地区进行了7个饱和黄土原位大型剪切试验.结果表明,2种饱和方法都能够使土样饱和,“饱和后制样法”容易达到饱和,试验历时短,但对试样扰动大,甚至导致试样在制样时破坏,试验成功率低;“制样后饱和法”达到饱和历时稍长,对试样扰动小,试验成功率高.与原位天然大剪试验相比,粘聚力c值由44.65kPa下降至17.35kPa,φ值由14.18°降至11.95°;与室内饱和固结快剪相比,饱和黄土原位大剪的c值增加约4kPa,φ值增加3°左右. 相似文献