共查询到20条相似文献，搜索用时 15 毫秒
1.
Geostatistical seismic inversion for non‐stationary patterns using direct sequential simulation and co‐simulation 
下载免费PDF全文
下载免费PDF全文 Hamid Sabeti Ali Moradzadeh Faramarz Doulati Ardejani Leonardo Azevedo Amilcar Soares Pedro Pereira Ruben Nunes 《Geophysical Prospecting》2017,65(Z1):25-48
Geostatistical seismic inversion methods are routinely used in reservoir characterisation studies because of their potential to infer the spatial distribution of the petro‐elastic properties of interest (e.g., density, elastic, and acoustic impedance) along with the associated spatial uncertainty. Within the geostatistical seismic inversion framework, the retrieved inverse elastic models are conditioned by a global probability distribution function and a global spatial continuity model as estimated from the available well‐log data for the entire inversion grid. However, the spatial distribution of the real subsurface elastic properties is complex, heterogeneous, and, in many cases, non‐stationary since they directly depend on the subsurface geology, i.e., the spatial distribution of the facies of interest. In these complex geological settings, the application of a single distribution function and a spatial continuity model is not enough to properly model the natural variability of the elastic properties of interest. In this study, we propose a three‐dimensional geostatistical inversion technique that is able to incorporate the reservoir's heterogeneities. This method uses a traditional geostatistical seismic inversion conditioned by local multi‐distribution functions and spatial continuity models under non‐stationary conditions. The procedure of the proposed methodology is based on a zonation criterion along the vertical direction of the reservoir grid. Each zone can be defined by conventional seismic interpretation, with the identification of the main seismic units and significant variations of seismic amplitudes. The proposed method was applied to a highly non‐stationary synthetic seismic dataset with different levels of noise. The results of this work clearly show the advantages of the proposed method against conventional geostatistical seismic inversion procedures. It is important to highlight the impact of this technique in terms of higher convergence between real and inverted reflection seismic data and the more realistic approximation towards the real subsurface geology comparing with traditional techniques. 相似文献
2.
Elastic full waveform inversion of seismic reflection data represents a data‐driven form of analysis leading to quantification of sub‐surface parameters in depth. In previous studies attention has been given to P‐wave data recorded in the marine environment, using either acoustic or elastic inversion schemes. In this paper we exploit both P‐waves and mode‐converted S‐waves in the marine environment in the inversion for both P‐ and S‐wave velocities by using wide‐angle, multi‐component, ocean‐bottom cable seismic data. An elastic waveform inversion scheme operating in the time domain was used, allowing accurate modelling of the full wavefield, including the elastic amplitude variation with offset response of reflected arrivals and mode‐converted events. A series of one‐ and two‐dimensional synthetic examples are presented, demonstrating the ability to invert for and thereby to quantify both P‐ and S‐wave velocities for different velocity models. In particular, for more realistic low velocity models, including a typically soft seabed, an effective strategy for inversion is proposed to exploit both P‐ and mode‐converted PS‐waves. Whilst P‐wave events are exploited for inversion for P‐wave velocity, examples show the contribution of both P‐ and PS‐waves to the successful recovery of S‐wave velocity. 相似文献
3.
By applying seismic inversion, we can derive rock impedance from seismic data. Since it is an interval property, impedance is valuable for reservoir characterization. Furthermore, the decomposition of the impedance into two fundamental properties, i.e. velocity and density, provides a link to the currently available rock‐physics applications to derive quantitative reservoir properties. However, the decomposition is a challenging task due to the strong influence of noise, especially for seismic data with a maximum offset angle of less than 30°. We present a method of impedance decomposition using three elastic impedance data derived from the seismic inversion of angle stacks, where the far‐stack angle is 23.5°. We discuss the effect of noise on the analysis as being the most significant cause of making the decomposition difficult. As the result, the offset‐consistent component of noise mostly affects the determination of density but not the velocities (P‐ and S‐wave), whereas the effect of the random component of noise occurs equally in the determination of the velocities and density. The effect is controlled by the noise enhancement factor 1/A, which is determined by a combination of stack angles. Based on the results of the analysis, we show an innovative method of decomposition incorporating rock‐physics bounds as constraints for the analysis. The method is applied to an actual data set from an offshore oilfield; we demonstrate the result of analysis for sandbody detection. 相似文献
4.
A nonlinear method for multiparameter inversion of pre‐stack seismic data based on anisotropic Markov random field 下载免费PDF全文
下载免费PDF全文 Hongbing Zhang Qiang Guo Lifeng Liang Chenghao Cao Zuoping Shang 《Geophysical Prospecting》2018,66(3):461-477
Multiparameter inversion for pre‐stack seismic data plays a significant role in quantitative estimation of subsurface petrophysical properties. However, it remains a complicated problem due to the non‐unique results and unstable nature of the processing; the pre‐stack seismic inversion problem is ill‐posed and band‐limited. Combining the full Zoeppritz equation and additional assumptions with edge‐preserving regularisation can help to alleviate these problems. To achieve this, we developed an inversion method by constructing a new objective function that includes edge‐preserving regularisation and soft constraints based on anisotropic Markov random fields and is intended especially for layered formations. We applied a fast simulated annealing algorithm to solve the nonlinear optimisation problem. The method directly obtains reflectivity RPP values using the full Zoeppritz equation instead of its approximations and effectively controls the stability of the multiparameter inversion by assuming a sectionally constant S‐ and P‐wave velocity ratio and using the generalised Gardner equation. We substituted the inverted parameters, i.e., the P‐wave velocity, the fitting deviation of S‐wave velocity, and the density were inverted instead of the P‐wave velocity, the S‐wave velocity, and the density, and the generalised Gardner equation was applied as a constraint. Test results on two‐dimensional synthetic data indicated that our substitution obtained improved results for multiparameter inversion. The inverted results could be improved by utilising high‐order anisotropic Markov random field neighbourhoods at early stages and low‐order anisotropic Markov random field neighbourhoods in the later stages. Moreover, for layered formations, using a large horizontal weighting coefficient can preserve the lateral continuity of layers, and using a small vertical weighting coefficient allows for large longitudinal gradients of the interlayers. The inverted results of the field data revealed more detailed information about the layers and matched the logging curves at the wells acceptably over most parts of the curves. 相似文献
5.
叠前反演技术已经成为岩性预测和流体识别的关键技术,并将在油气勘探中发挥重要作用,本文提出了模拟退火AVA同步反演方法,该方法以多个角道集地震数据体和先验纵波速度、横波速度、密度模型等为输入,综合利用地震、地质、测井等多种信息为约束,采用模拟退火全局优化方法,直接采用Knott-Zoeppritz方程求解反射系数,同步反演获得纵波阻抗、横波阻抗、纵横波速度、密度、Mu、Lambda等23种岩石弹性参数模型.其主要特点如下：１）采用Zoeppritz方程直接求解,精度高;2) 目标函数选择灵活;３）多角度提取子波;４）可获得深度域的反演结果.实际资料应用证明,该反演方法保留了地震反射振幅随偏移距不同或入射角不同而变化的特征,可有效提高储层预测和流体识别精度.实际应用表明,本方法预测结果可靠,具有较强的实用性. 相似文献
6.
Average elastic properties of a fluid‐saturated fractured rock are discussed in association with the extremely slow and dispersive Krauklis wave propagation within individual fractures. The presence of the Krauklis wave increases P‐wave velocity dispersion and attenuation with decreasing frequency. Different laws (exponential, power, fractal, and gamma laws) of distribution of the fracture length within the rock show more velocity dispersion and attenuation of the P‐wave for greater fracture density, particularly at low seismic frequencies. The results exhibit a remarkable difference in the P‐wave reflection coefficient for frequency and angular dependency from the fractured layer in comparison with the homogeneous layer. The biggest variation in behaviour of the reflection coefficient versus incident angle is observed at low seismic frequencies. The proposed approach and results of calculations allow an interpretation of abnormal velocity dispersion, high attenuation, and special behaviour of reflection coefficients versus frequency and angle of incidence as the indicators of fractures. 相似文献
7.
Prestack seismic inversion plays an important role in estimating elastic parameters that are sensitive to reservoirs and fluid underground. In this paper, a simultaneous inversion method named FMR‐AVA (Fluid Factor, Mu (Shear modulus), Rho (Density)‐Amplitude Variation with Angle) is proposed based on partial angle stack seismic gathers. This method can be used for direct inversion for the fluid factor, shear modulus and density of heterogeneous reservoirs. Firstly, an FMR approximation equation of a reflection coefficient is derived based on poroelasticity with P‐ and S‐wave moduli. Secondly, a stable simultaneous AVA inversion approach is presented in a Bayesian scheme. This approach has little dependence on initial models. Furthermore, it can be applied in heterogeneous reservoirs whose initial models for inversion are not easy to establish. Finally, a model test shows the superiority of this FMR‐AVA inversion method in stability and independence of initial models. We obtain a reasonable fluid factor, shear modulus and density even with smooth initial models and moderate Gaussian noise. A real data case example shows that the inverted fluid factor, shear modulus and density fit nicely with well log interpretation results, which verifies the effectiveness of the proposed method. 相似文献
8.
Bayesian inversion of time‐lapse seismic data for the estimation of static reservoir properties and dynamic property changes 下载免费PDF全文
下载免费PDF全文 Seismic conditioning of static reservoir model properties such as porosity and lithology has traditionally been faced as a solution of an inverse problem. Dynamic reservoir model properties have been constrained by time‐lapse seismic data. Here, we propose a methodology to jointly estimate rock properties (such as porosity) and dynamic property changes (such as pressure and saturation changes) from time‐lapse seismic data. The methodology is based on a full Bayesian approach to seismic inversion and can be divided into two steps. First we estimate the conditional probability of elastic properties and their relative changes; then we estimate the posterior probability of rock properties and dynamic property changes. We apply the proposed methodology to a synthetic reservoir study where we have created a synthetic seismic survey for a real dynamic reservoir model including pre‐production and production scenarios. The final result is a set of point‐wise probability distributions that allow us to predict the most probable reservoir models at each time step and to evaluate the associated uncertainty. Finally we also show an application to real field data from the Norwegian Sea, where we estimate changes in gas saturation and pressure from time‐lapse seismic amplitude differences. The inverted results show the hydrocarbon displacement at the times of two repeated seismic surveys. 相似文献
9.
We develop a two‐dimensional full waveform inversion approach for the simultaneous determination of S‐wave velocity and density models from SH ‐ and Love‐wave data. We illustrate the advantages of the SH/Love full waveform inversion with a simple synthetic example and demonstrate the method's applicability to a near‐surface dataset, recorded in the village ?achtice in Northwestern Slovakia. Goal of the survey was to map remains of historical building foundations in a highly heterogeneous subsurface. The seismic survey comprises two parallel SH‐profiles with maximum offsets of 24 m and covers a frequency range from 5 Hz to 80 Hz with high signal‐to‐noise ratio well suited for full waveform inversion. Using the Wiechert–Herglotz method, we determined a one‐dimensional gradient velocity model as a starting model for full waveform inversion. The two‐dimensional waveform inversion approach uses the global correlation norm as objective function in combination with a sequential inversion of low‐pass filtered field data. This mitigates the non‐linearity of the multi‐parameter inverse problem. Test computations show that the influence of visco‐elastic effects on the waveform inversion result is rather small. Further tests using a mono‐parameter shear modulus inversion reveal that the inversion of the density model has no significant impact on the final data fit. The final full waveform inversion S‐wave velocity and density models show a prominent low‐velocity weathering layer. Below this layer, the subsurface is highly heterogeneous. Minimum anomaly sizes correspond to approximately half of the dominant Love‐wavelength. The results demonstrate the ability of two‐dimensional SH waveform inversion to image shallow small‐scale soil structure. However, they do not show any evidence of foundation walls. 相似文献
10.
Angus I. Best Lucy M. MacGregor Jeremy Sothcott Tim A. Minshull 《Geophysical Prospecting》2011,59(4):777-786
Improvements in the joint inversion of seismic and marine controlled source electromagnetic data sets will require better constrained models of the joint elastic‐electrical properties of reservoir rocks. Various effective medium models were compared to a novel laboratory data set of elastic velocity and electrical resistivity (obtained on 67 reservoir sandstone samples saturated with 35 g/l brine at a differential pressure of 8 MPa) with mixed results. Hence, we developed a new three‐phase effective medium model for sandstones with pore‐filling clay minerals based on the combined self‐consistent approximation and differential effective medium model. We found that using a critical porosity of 0.5 and an aspect ratio of 1 for all three components, the proposed model gave accurate model predictions of the observed magnitudes of P‐wave velocity and electrical resistivity and of the divergent trends of clean and clay‐rich sandstones at higher porosities. Using only a few well‐constrained input parameters, the new model offers a practical way to predict in situ porosity and clay content in brine saturated sandstones from co‐located P‐wave velocity and electrical resistivity data sets. 相似文献
11.
We measured in the laboratory ultrasonic compressional and shear‐wave velocity and attenuation (0.7–1.0 MHz) and low‐frequency (2 Hz) electrical resistivity on 63 sandstone samples with a wide range of petrophysical properties to study the influence of reservoir porosity, permeability and clay content on the joint elastic‐electrical properties of reservoir sandstones. P‐ and S‐wave velocities were found to be linearly correlated with apparent electrical formation factor on a semi‐logarithmic scale for both clean and clay‐rich sandstones; P‐ and S‐wave attenuations showed a bell‐shaped correlation (partial for S‐waves) with apparent electrical formation factor. The joint elastic‐electrical properties provide a way to discriminate between sandstones with similar porosities but with different clay contents. The laboratory results can be used to estimate sandstone reservoir permeability from seismic velocity and apparent formation factor obtained from co‐located seismic and controlled source electromagnetic surveys. 相似文献
12.
Sensitivity of time-lapse seismic to reservoir stress path 总被引：1，自引：1，他引：1
Colin M. Sayers 《Geophysical Prospecting》2006,54(3):369-380
The change in reservoir pore pressure due to the production of hydrocarbons leads to anisotropic changes in the stress field acting on the reservoir. Reservoir stress path is defined as the ratio of the change in effective horizontal stress to the change in effective vertical stress from the initial reservoir conditions, and strongly influences the depletion‐induced compaction behaviour of the reservoir. Seismic velocities in sandstones vary with stress due to the presence of stress‐sensitive regions within the rock, such as grain boundaries, microcracks, fractures, etc. Since the response of any microcracks and grain boundaries to a change in stress depends on their orientation relative to the principal stress axes, elastic‐wave velocities are sensitive to reservoir stress path. The vertical P‐ and S‐wave velocities, the small‐offset P‐ and SV‐wave normal‐moveout (NMO) velocities, and the P‐wave amplitude‐versus‐offset (AVO) are sensitive to different combinations of vertical and horizontal stress. The relationships between these quantities and the change in stress can be calibrated using a repeat seismic, sonic log, checkshot or vertical seismic profile (VSP) at the location of a well at which the change in reservoir pressure has been measured. Alternatively, the variation of velocity with azimuth and distance from the borehole, obtained by dipole radial profiling, can be used. Having calibrated these relationships, the theory allows the reservoir stress path to be monitored using time‐lapse seismic by combining changes in the vertical P‐wave impedance, changes in the P‐wave NMO and AVO behaviour, and changes in the S‐wave impedance. 相似文献
13.
We describe a method to invert a walkaway vertical seismic profile (VSP) and predict elastic properties (P‐wave velocity, S‐wave velocity and density) in a layered model looking ahead of the deepest receiver. Starting from Bayes's rule, we define a posterior distribution of layered models that combines prior information (on the overall variability of and correlations among the elastic properties observed in well logs) with information provided by the VSP data. This posterior distribution of layered models is sampled by a Monte‐Carlo method. The sampled layered models agree with prior information and fit the VSP data, and their overall variability defines the uncertainty in the predicted elastic properties. We apply this technique first to a zero‐offset VSP data set, and show that uncertainty in the long‐wavelength P‐wave velocity structure results in a sizable uncertainty in the predicted elastic properties. We then use walkaway VSP data, which contain information on the long‐wavelength P‐wave velocity (in the reflection moveout) and on S‐wave velocity and density contrasts (in the change of reflectivity with offset). The uncertainty of the look‐ahead prediction is considerably decreased compared with the zero‐offset VSP, and the predicted elastic properties are in good agreement with well‐log measurements. 相似文献
14.
In order to account for the effects of elastic wave propagation in marine seismic data, we develop a waveform inversion algorithm for acoustic‐elastic media based on a frequency‐domain finite‐element modelling technique. In our algorithm we minimize residuals using the conjugate gradient method, which back‐propagates the errors using reverse time migration without directly computing the partial derivative wavefields. Unlike a purely acoustic or purely elastic inversion algorithm, the Green's function matrix for our acoustic‐elastic algorithm is asymmetric. We are nonetheless able to achieve computational efficiency using modern numerical methods. Numerical examples show that our coupled inversion algorithm produces better velocity models than a purely acoustic inversion algorithm in a wide variety of cases, including both single‐ and multi‐component data and low‐cut filtered data. We also show that our algorithm performs at least equally well on real field data gathered in the Korean continental shelf. 相似文献
15.
煤层中存在的裂隙会导致介质表现为各向异性,本文以HTI型煤层为例,结合各向异性介质弹性矩阵和各向异性裂隙理论,推导出不同充填物的垂直裂隙中各向异性参数表达式,将其应用于地震波响应分析;通过改进的交错网格差分法和各向异性Christoffel方程波场分解法,得到地震波合成记录和分解后的P波和SV波记录;将Thomsen群速度与相速度公式,经过坐标轴旋转变换,得到HTI型煤层中不同各向异性参数的地震波速度响应表达式;建立不同类型煤层地质模型,分析了裂隙密度、裂隙充填物以及煤层厚度等参数变化时的地震波响应特征.研究结果为分析垂向裂隙各向异性薄煤层地震波传播规律提供工具,为选用相应地震数据进行地震波各向异性参数反演提供依据. 相似文献
16.
We develop a new time‐domain reverse‐time migration method called double plane‐wave reverse‐time migration that uses plane‐wave transformed gathers. Original shot gathers with appropriate data acquisition geometry are double slant stacked into the double plane‐wave domain with minimal slant stacking artefacts. The range of plane‐wave components needed for migration can be determined by estimating the maximum time dips present in shot gathers. This reduces the total number of input traces for migration and increases migration efficiency. Unlike the pre‐stack shot‐profile reverse‐time migration where the number of forward propagations is proportional to the number of shots, the number of forward propagations needed for the proposed method remains constant and is relatively small even for large seismic datasets. Therefore, the proposed method can improve the efficiency of the migration and be suitable for migrating large datasets. Double plane‐wave reverse‐time migration can be performed for selected plane‐wave components to obtain subsurface interfaces with different dips, which makes the migration method target oriented. This feature also makes the method a useful tool for migration velocity analysis. For example, we are able to promptly obtain trial images with nearly horizontal interfaces and adjust velocity models according to common image gathers. Seismic signal coming from steeply dipping interfaces can be included into the migration to build images with more detailed structures and higher spatial resolution as better velocity models become available. Illumination compensation imaging conditions for the proposed method are also introduced to obtain images with balanced amplitudes. 相似文献
17.
Ho Seuk Bae Changsoo Shin Young Ho Cha Yunseok Choi Dong‐Joo Min 《Geophysical Prospecting》2010,58(6):997-1010
Although waveform inversion has been intensively studied in an effort to properly delineate the Earth's structures since the early 1980s, most of the time‐ and frequency‐domain waveform inversion algorithms still have critical limitations in their applications to field data. This may be attributed to the highly non‐linear objective function and the unreliable low‐frequency components. To overcome the weaknesses of conventional waveform inversion algorithms, the acoustic Laplace‐domain waveform inversion has been proposed. The Laplace‐domain waveform inversion has been known to provide a long‐wavelength velocity model even for field data, which may be because it employs the zero‐frequency component of the damped wavefield and a well‐behaved logarithmic objective function. However, its applications have been confined to 2D acoustic media. We extend the Laplace‐domain waveform inversion algorithm to a 2D acoustic‐elastic coupled medium, which is encountered in marine exploration environments. In 2D acoustic‐elastic coupled media, the Laplace‐domain pressures behave differently from those of 2D acoustic media, although the overall features are similar to each other. The main differences are that the pressure wavefields for acoustic‐elastic coupled media show negative values even for simple geological structures unlike in acoustic media, when the Laplace damping constant is small and the water depth is shallow. The negative values may result from more complicated wave propagation in elastic media and at fluid‐solid interfaces. Our Laplace‐domain waveform inversion algorithm is also based on the finite‐element method and logarithmic wavefields. To compute gradient direction, we apply the back‐propagation technique. Under the assumption that density is fixed, P‐ and S‐wave velocity models are inverted from the pressure data. We applied our inversion algorithm to the SEG/EAGE salt model and the numerical results showed that the Laplace‐domain waveform inversion successfully recovers the long‐wavelength structures of the P‐ and S‐wave velocity models from the noise‐free data. The models inverted by the Laplace‐domain waveform inversion were able to be successfully used as initial models in the subsequent frequency‐domain waveform inversion, which is performed to describe the short‐wavelength structures of the true models. 相似文献
18.
Joint facies and rock properties Bayesian amplitude‐versus‐offset inversion using Markov random fields 下载免费PDF全文
下载免费PDF全文 Seismic reflection pre‐stack angle gathers can be simultaneously inverted within a joint facies and elastic inversion framework using a hierarchical Bayesian model of elastic properties and categorical classes of rock and fluid properties. The Bayesian prior implicitly supplies low frequency information via a set of multivariate compaction trends for each rock and fluid type, combined with a Markov random field model of lithotypes, which carries abundance and continuity preferences. For the likelihood, we use a simultaneous, multi‐angle, convolutional model, which quantifies the data misfit probability using wavelets and noise levels inferred from well ties. Under Gaussian likelihood and facies‐conditional prior models, the posterior has simple analytic form, and the maximum a‐posteriori inversion problem boils down to a joint categorical/continuous non‐convex optimisation problem. To solve this, a set of alternative, increasingly comprehensive optimisation strategies is described: (i) an expectation–maximisation algorithm using belief propagation, (ii) a globalisation of method (i) using homotopy, and (iii) a discrete space approach using simulated annealing. We find that good‐quality inversion results depend on both sensible, elastically separable facies definitions, modest resolution ambitions, reasonably firm abundance and continuity parameters in the Markov random field, and suitable choice of algorithm. We suggest usually two to three, perhaps four, unknown facies per sample, and usage of the more expensive methods (homotopy or annealing) when the rock types are not strongly distinguished in acoustic impedance. Demonstrations of the technique on pre‐stack depth‐migrated field data from the Exmouth basin show promising agreements with lithological well data, including prediction accuracy improvements of 24% in and twofold in density, in comparison to a standard simultaneous inversion. Much clearer and extensive recovery of the thin Pyxis gas field was evident using stronger coupling in the Markov random field model and use of the homotopy or annealing algorithms. 相似文献
19.
20.
Joint inversion of Rayleigh‐wave dispersion data and vertical electric sounding data: synthetic tests on characteristic sub‐surface models 下载免费PDF全文
下载免费PDF全文 In the traditional inversion of the Rayleigh dispersion curve, layer thickness, which is the second most sensitive parameter of modelling the Rayleigh dispersion curve, is usually assumed as correct and is used as fixed a priori information. Because the knowledge of the layer thickness is typically not precise, the use of such a priori information may result in the traditional Rayleigh dispersion curve inversions getting trapped in some local minima and may show results that are far from the real solution. In this study, we try to avoid this issue by using a joint inversion of the Rayleigh dispersion curve data with vertical electric sounding data, where we use the common‐layer thickness to couple the two methods. The key idea of the proposed joint inversion scheme is to combine methods in one joint Jacobian matrix and to invert for layer S‐wave velocity, resistivity, and layer thickness as an additional parameter, in contrast with a traditional Rayleigh dispersion curve inversion. The proposed joint inversion approach is tested with noise‐free and Gaussian noise data on six characteristic, synthetic sub‐surface models: a model with a typical dispersion; a low‐velocity, half‐space model; a model with particularly stiff and soft layers, respectively; and a model reproduced from the stiff and soft layers for different layer‐resistivity propagation. In the joint inversion process, the non‐linear damped least squares method is used together with the singular value decomposition approach to find a proper damping value for each iteration. The proposed joint inversion scheme tests many damping values, and it chooses the one that best approximates the observed data in the current iteration. The quality of the joint inversion is checked with the relative distance measure. In addition, a sensitivity analysis is performed for the typical dispersive sub‐surface model to illustrate the benefits of the proposed joint scheme. The results of synthetic models revealed that the combination of the Rayleigh dispersion curve and vertical electric sounding methods in a joint scheme allows to provide reliable sub‐surface models even in complex and challenging situations and without using any a priori information. 相似文献