首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献，搜索用时 578 毫秒
1.
The shear modulus at very small strains (less than 0.001%) is an important parameter in the design of geotechnical structures subjected to static and cyclic loadings. Although numerous soil models are available for predicting shear modulus of saturated and dry soils, only a few ones can predict shear stiffness at very small strains of unsaturated soils correctly. In this study, a few unsaturated soil models are evaluated critically and compared with a newly developed model. This newly proposed model is verified by using measured shear modulus at very small strains for three different low plasticity fine grained soils available in the literature. It is found that this new model can predict shear modulus at very small strain resulting from an increase and a decrease in mean net stress at constant matric suction for low plasticity fine grained soils. Moreover, this model is able to give a reasonably good prediction on shear stiffness at very small strain during wetting of a collapsible unsaturated soil. In addition, the newly proposed model is illustrated to capture a consistent trend with experimental data of shear stiffness at very small strain for non-collapsible soils obtained during drying–wetting cycles. This evaluation revealed that the newly proposed model has better predictive capabilities than some earlier formulations of the same simplicity. In addition, the proposed model with fewer parameters has similar predictive capability as compared with a more complex model.  相似文献   

2.
In many geotechnical systems, such as reinforced slopes and embankments, soil-structure interfaces are often unsaturated. Shear behaviour of unsaturated interfaces is strongly dependent on their matric suctions, as revealed by the results of extensive laboratory tests. So far, constitutive models for unsaturated interfaces are very limited in the literature. This paper reports a new bounding surface model for saturated and unsaturated interfaces. New formulations were developed to incorporate suction effects on the flow rule and plastic modulus. To examine the capability of the proposed model, it was applied to simulate suction- and stress-controlled direct shear tests on unsaturated soil–cement, soil–steel and soil–geotextile interfaces. Measured and computed results are well matched, demonstrating that the proposed model can well capture key features of the shear behaviour of unsaturated interfaces, including suction-dependent dilatancy, stress–strain relation and peak and critical state shear strengths.  相似文献   

3.
A unified constitutive model for unsaturated soils is presented in a critical state framework using the concepts of effective stress and bounding surface plasticity theory. Consideration is given to the effects of unsaturation and particle crushing in the definition of the critical state. A simple isotropic elastic rule is adopted. A loading surface and a bounding surface of the same shape are defined using simple and versatile functions. The bounding surface and elastic rules lead to the existence of a limiting isotropic compression line, towards which the stress trajectories of all isotropic compression load paths approach. A non‐associated flow rule of the same general form is assumed for all soil types. Isotropic hardening/softening occurs due to changes in plastic volumetric strains as well as suction for some unsaturated soils, enabling the phenomenon of volumetric collapse upon wetting to be accounted for. The model is used to simulate the stress–strain behaviour observed in unsaturated speswhite kaolin subjected to three triaxial test load paths. The fit between simulation and experiment is improved compared to that of other constitutive models developed using conventional Cam‐Clay‐based plasticity theory and calibrated using the same set of data. Also, the model is used to simulate to a high degree of accuracy the stress–strain behaviour observed in unsaturated Kurnell sand subjected to two triaxial test load paths and the oedometric compression load path. For oedometric compression theoretical simulations indicate that the suction was not sufficiently large to cause samples to separate from the confining ring. Copyright © 2005 John Wiley & Sons, Ltd.  相似文献   

4.
The Barcelona basic model cannot predict the mechanical behaviour of unsaturated expansive soils, whereas the Barcelona expansive model (BExM) can only predict the stress–strain behaviour of unsaturated expansive soils without the water‐retention behaviour being incorporated. Moreover, the micro‐parameters and the coupling function between micro‐structural and macro‐structural strains in the BExM are difficult to determine. Experimental data show that the compression curves for non‐expansive soils under constant suctions are shifted towards higher void ratios with increasing suction, whereas the opposite is true for expansive soils. According to the observed water‐retention behaviour of unsaturated expansive soils, the air‐entry value increases with density, and the relationship between the degree of saturation and void ratio is linear at constant suction. According to the above observation, an elastoplastic constitutive model is developed for predicting the hydraulic and mechanical behaviour of unsaturated expansive soils, based on the existing hydro‐mechanical model for non‐expansive unsaturated soil. The model takes into consideration the effect of degree of saturation on the mechanical behaviour and that of void ratio on the water‐retention behaviour. The concept of equivalent void ratio curve is introduced to distinguish the plastic potential curve from the yield curve. The model predictions are compared with the test results of an unsaturated expansive soil, including swelling tests under constant net stress, isotropic compression tests and triaxial shear tests under constant suction. The comparison indicates that the model offers great potential for quantitatively predicting the hydraulic and mechanical behaviour of unsaturated expansive soils. Copyright © 2011 John Wiley & Sons, Ltd.  相似文献   

5.
Existing models for predicting the small strain behaviour of unsaturated soil are not capable of predicting the initial shear stiffness during suction reduction under normally consolidated conditions. This problem has been addressed in the present study by combining an existing elastoplastic model and recent experimental data to provide a new model for the initial shear stiffness. The model, which is similar to that typically adopted for saturated soils, uses the average skeleton stress and an additional function of the degree of saturation. This new model not only captures the behaviour of the new experimental results, but it also describes a unique relationship between saturated and unsaturated soils.  相似文献   

6.
In the last decades, a number of hydro-mechanical elastoplastic constitutive models for unsaturated soils have been proposed. Those models couple the hydraulic and mechanical behaviour of unsaturated soils, and take into account the effects of the degree of saturation on the stress–strain behaviour and the effects of deformation on the soil–water characteristic response with a simple reversible part for the hysteresis. In addition, the influence of the suction on the stress–strain behaviour is considered. However, until now, few models predict the stress–strain and soil–water characteristic responses of unsaturated soils in a fully three-dimensional Finite Element code. This paper presents the predictions of an unsaturated soil model in a Three-dimensional Framework, and develops a study on the effect of partial saturation on the stability of shallow foundation resting on unsaturated silty soil. Qualitative predictions of the constitutive model show that incorporating a special formulation for the effective stress into an elastoplastic coupled hydro-mechanical model opens a full range of possibilities in modelling unsaturated soil behaviour.  相似文献   

7.
This paper presents a three‐dimensional elastoplastic constitutive model for predicting the hydraulic and mechanical behaviour of unsaturated soils. It is based on experimental results obtained from a series of controlled‐suction triaxial tests on unsaturated compacted clay with different initial densities. Hydraulic hysteresis in the water‐retention behaviour is modelled as an elastoplastic process, with the elastic part modelled by a series of scanning curves and the elastoplastic part modelled by the main drying and wetting curves. The effect of void ratio on the water‐retention behaviour is studied using data obtained from controlled‐suction wetting–drying cyclic tests on unsaturated compacted clay with different initial densities. The effect of the degree of saturation on the stress–strain‐strength behaviour and the effect of void ratio on the water‐retention behaviour are considered in the model, as is the effect of suction on the hydraulic and mechanical behaviour. The initial density dependency of the compacted soil behaviour is modelled by experimental relationships between the initial density and the corresponding yield stress and, thereby, between the initial density and the normal compression line. The model is generalized to three‐dimensional stress states by assuming that the shapes of the failure and yield surfaces in the deviatoric stress plane are given by the Matsuoka–Nakai criterion. Model predictions of the stress–strain and water‐retention behaviour are compared with those obtained from triaxial tests with different initial densities under isotropic compression, triaxial compression and triaxial extension, with or without variation in suction. The comparisons indicate that the model accurately predicts the hydraulic and mechanical behaviour of unsaturated compacted soils with different initial densities using the same material constant. Copyright © 2006 John Wiley & Sons, Ltd.  相似文献   

8.
A new constitutive model for intact rock is presented recognising that rock strength, stiffness and stress–strain behaviour are affected by the size of the rock being subjected to loading. The model is formulated using bounding surface plasticity theory. It is validated against a new and extensive set of unconfined compression and triaxial compression test results for Gosford sandstone. The samples tested had diameters ranging from 19 to 145 mm and length-to-diameter ratios of 2. The model captures the continuous nonlinear stress–strain behaviour from initial loading, through peak strength to large shear strains, including transition from brittle to ductile behaviour. The size dependency was accounted for through a unified size effect law applied to the unconfined compressive strength—a key model input parameter. The unconfined compressive strength increases with sample size before peaking and then decreasing with further increasing sample size. Inside the constitutive model two hardening laws act simultaneously, each driven by plastic shear strains. The elasticity is stress level dependent. Simple linear loading and bounding surfaces are adopted, defined using the Mohr–Coulomb criterion, along with a non-associated flow rule. The model simulates well the stress–strain behaviour of Gosford sandstone at confining pressures ranging from 0 to 30 MPa for the variety of sample sizes considered.  相似文献   

9.
This paper presents an elasto‐plastic model for unsaturated compacted soils and experimental results obtained from a series of suction‐controlled triaxial tests on unsaturated compacted clay with different initial densities. The initial density dependency of the compacted soil behaviour is modelled by establishing experimental relationships between the initial density and the corresponding yield stress and thereby between the initial density and the location and slope of normal compression line. The model is generalized to three‐dimensional stress states by assuming that the shapes of the failure surface and the yield surface in the deviatoric plane are given by the extended SMP criterion. A considerable number of the isotropic compression, triaxial compression and extension tests on unsaturated compacted clay with different initial densities were performed using a suction‐controllable triaxial apparatus, to measure the stress–strain–volume change in different stress paths and wetting paths. The model has well‐predicting capabilities to reproduce the mechanical behaviour of specimens compacted under different conditions not only in isotropic compression but also in triaxial compression and triaxial extension. Copyright © 2003 John Wiley & Sons, Ltd.  相似文献   

10.
Cavity expansion theory assists in the interpretation of in situ tests including the cone penetration test and pressuremeter test. In this paper, a cavity expansion analysis is presented for unsaturated silty sand exhibiting hydraulic hysteresis. The similarity technique is used in the analysis. The soil stress–strain behaviour is described by a bounding surface plasticity model. Results of oedometric compression tests, isotropic compression tests and triaxial shear tests for both saturated and unsaturated states are used to calibrate the model. The void ratio, suction, degree of saturation and effective stress are fully coupled in the analysis. The influence of where the initial hydraulic state is located on the soil–water characteristic curve on the cavity wall pressure is investigated and found to be significant. Also, the effects of three different drainage conditions (constant suction, constant moisture content and constant contribution of suction to the effective stress) on cavity wall pressure are studied. It is found that the drainage condition in which the contribution of suction to the effective stress is constant offers a good approximation to the other two. This may simplify interpretation of in situ tests. When testing occurs quickly, meaning a constant moisture content condition prevails, a constant contribution of suction condition can be assumed without loss of significant accuracy. The contribution of suction assumed in the interpretation can be taken as being equal to the in situ value, although this discovery may not be applicable to all soil types, constitutive models and soil–water characteristic curves. Copyright © 2015 John Wiley & Sons, Ltd.  相似文献   

11.
徐洁  周超 《岩土力学》2015,36(Z1):377-381
天然土尤其是地表浅层土常处于非饱和状态,其小应变剪切模量是预测地基变形及土工结构物动力反应的一个重要参数。通过对非饱和压实粉土三轴样进行弯曲元试验,研究了吸力和干湿路径对其小应变剪切模量的影响。试验结果表明,非饱和压实粉土样的小应变剪切模量各向异性忽略不计;小应变剪切模量G0(vh)、G0(hh)和G0(hv)均随吸力增大而非线性增大;同一吸力下不同干湿路径上的土样,饱和度不同,其小应变剪切模量随饱和度升高而减小,主要原因是土的平均骨架应力和土中毛细水的作用。根据试验结果对非饱和土小应变剪切模量的半经验公式进行了改进,同时考虑了吸力与饱和度的作用。  相似文献   

12.
A simple thermo‐hydro‐mechanical (THM) constitutive model for unsaturated soils is described. The effective stress concept is extended to unsaturated soils with the introduction of a capillary stress. This capillary stress is based on a microstructural model and calculated from attraction forces due to water menisci. The effect of desaturation and the thermal softening phenomenon are modelled with a minimal number of material parameters and based on existing models. THM process is qualitatively and quantitatively modelled by using experimental data and previous work to show the application of the model, including a drying path under mechanical stress with transition between saturated and unsaturated states, a heating path under constant suction and a deviatoric path with imposed suction and temperature. The results show that the present model can simulate the THM behaviour in unsaturated soils in a satisfactory way. Copyright © 2010 John Wiley & Sons, Ltd.  相似文献   

13.
The small strain stiffness of soils has a significant role in geotechnical design and analysis. In laboratory, the small strain behavior is examined by different techniques including the bender element method for measuring the maximum shear modulus and local displacement transducer (LDT) for measuring Young’s modulus at small strains. However, most commonly used LDTs are based on electrical components and have limitations, such as electromagnetic interference and possibility of short circuit in the presence of water. To overcome these limitations, in the present study, a conventional triaxial apparatus has been modified to measure and study the stress–strain behavior of soils at small strains. The major modifications include addition of piezoceramic sensors (bender elements) for measuring the maximum shear modulus and fiber Bragg grating (FBG) sensor-based local displacement transducers (FBG–LDTs) for measuring the stress–strain behavior at small strains. The modified triaxial apparatus has been used to conduct several tests on a completely decomposed granite soil from a site in Hong Kong. The stress–strain behaviors measured by the newly developed FBG–LDTs and an external displacement transducer are compared and discussed. In particular, the shear modulus values obtained using the bender elements, FBG–LTDs, and the external displacement transducer are also compared, discussed, and evaluated. The comparison and assessment show that the FBG–LTDs are more suitable for measuring the small strain behavior of soils.  相似文献   

14.
This paper presents a complete finite‐element treatment for unsaturated soil problems. A new formulation of general constitutive equations for unsaturated soils is first presented. In the incremental stress–strain equations, the suction or the pore water pressure is treated as a strain variable instead of a stress variable. The global governing equations are derived in terms of displacement and pore water pressure. The discretized governing equations are then solved using an adaptive time‐stepping scheme which automatically adjusts the time‐step size so that the integration error in the displacements and pore pressures lies close to a specified tolerance. The non‐linearity caused by suction‐dependent plastic yielding, suction‐dependent degree of saturation, and saturation‐dependent permeability is treated in a similar way to the elastoplasticity. An explicit stress integration scheme is used to solve the constitutive stress–strain equations at the Gauss point level. The elastoplastic stiffness matrix in the Euler solution is evaluated using the suction as well as the stresses and hardening parameters at the start of the subincrement, while the elastoplastic matrix in the modified Euler solution is evaluated using the suction at the end of the subincrement. In addition, when applying subincrementation, the same rate is applied to all strain components including the suction. Copyright © 2003 John Wiley & Sons, Ltd.  相似文献   

15.
Modelling the mechanical behaviour of unsaturated soils has been the subject of many research works in the past few decades. A number of constitutive models have been developed to describe the complex behaviour of unsaturated soils. Despite the significant advances in the constitutive theories for unsaturated soils, none of the existing models can completely describe the various aspects of the real behaviour of unsaturated soils. In this paper, a new unified approach is presented, based on the integration of a neural network and a genetic algorithm, for the modelling of unsaturated soils. In the proposed approach, a genetic algorithm was used to optimise the weights of the neural network. A three-layer sequential architecture was chosen for the neural network. The network had eight input neurons, five neurons in the hidden layer and three neurons in the output layer. The eight input neurons represented the initial gravimetric water content, initial dry density, degree of saturation, net mean stress with respect to pore-air pressure, axial strain, deviatoric stress, soil suction and volumetric strain, and the three neurons in the output layer represented the deviatoric stress, suction and volumetric strain at the end of each increment. The network was trained and tested using a database that included results from a comprehensive set of triaxial tests on unsaturated soils from the literature. The predictions of the proposed model were compared with the experimental results. The comparison of the results indicates that the proposed approach was accurate and robust in representing the mechanical behaviour of unsaturated soils.  相似文献   

16.
Unsaturated soils are highly heterogeneous 3‐phase porous media. Variations of temperature, the degree of saturation, and density have dramatic impacts on the hydro‐mechanical behavior of unsaturated soils. To model all these features, we present a thermo‐hydro‐plastic model in which the hydro‐mechanical hardening and thermal softening are incorporated in a hierarchical fashion for unsaturated soils. This novel constitutive model can capture heterogeneities in density, suction, the degree of saturation, and temperature. Specifically, this constitutive model has 2 ingredients: (1) it has a “mesoscale” mechanical state variable—porosity and 3 environmental state variables—suction, the degree of saturation, and temperature; (2) both temperature and mechanical effects on water retention properties are taken into account. The return mapping algorithm is applied to implement this model at Gauss point assuming an infinitesimal strain. At each time step, the return mapping is conducted only in principal elastic strain space, assuming no return mapping in suction and temperature. The numerical results obtained by this constitutive model are compared with the experimental results. It shows that the proposed model can simulate the thermo‐hydro‐mechanical behavior of unsaturated soils with satisfaction. We also conduct shear band analysis of an unsaturated soil specimen under plane strain condition to demonstrate the impact of temperature variation on shear banding triggered by initial material heterogeneities.  相似文献   

17.
回弹模量是反映路基弹性支撑能力的重要指标,并受运营期间基质吸力变化的显著影响。通过3种压实黏土试样的土-水特征曲线试验和重复动三轴试验,研究了回弹模量与基质吸力的相关性,并基于非饱和土有效应力原理,提出了考虑吸力效应的回弹模量预估模型。结果表明：基质吸力与回弹模量之间具有较强的非线性相关性,可采用指数形式进行两者的拟合;含水率由最佳含水率-4%提升至最佳含水率+4%时,受基质吸力减小的影响,回弹模量降幅达到29.1%～39.0%;在 土-水特征曲线过渡区,采用以饱和度表征的有效应力参数,可较好地反映基质吸力对于回弹模量的贡献,预估效果优于采用残余含水率或进气值相关的有效应力参数;在相同饱和度的情况下,黏粒含量越多、塑性指数越高,基质吸力对有效应力的贡献比例越小。  相似文献   

18.
A thermodynamically consistent extension of the constitutive equations of saturated soils to unsaturated conditions is often worked out through the use of a unique ‘effective’ interstitial pressure, accounting equivalently for the pressures of the saturating fluids acting separately on the internal solid walls of the pore network. The natural candidate for this effective interstitial pressure is the space averaged interstitial pressure. In contrast experimental observations have revealed that, at least, a pair of stress state variables was needed for a suitable framework to describe stress–strain–strength behaviour of unsaturated soils. The thermodynamics analysis presented here shows that the most general approach to the behaviour of unsaturated soils actually requires three stress state variables: the suction, which is required to describe the invasion of the soil by the liquid water phase through the retention curve; two effective stresses, which are required to describe the soil deformation at water saturation held constant. However a simple assumption related to the plastic flow rule leads to the final need of only a Bishop-like effective stress to formulate the stress–strain constitutive equation describing the soil deformation, while the retention properties still involve the suction and possibly the deformation. Commonly accepted models for unsaturated soils, that is the Barcelona Basic Model and any approach based on the use of an effective averaged interstitial pressure, appear as special extreme cases of the thermodynamic formulation proposed here.  相似文献   

19.
Han  Bowen  Cai  Guoqing  Zhou  Annan  Li  Jian  Zhao  Chenggang 《Acta Geotechnica》2021,16(5):1331-1354

The interparticle bonding effect due to water menisci plays an important role in the hydromechanical coupling properties of unsaturated soils. This paper presents an unsaturated hydromechanical coupling model that considers the influence of matric suction, degree of saturation, and microscopic pore structure on the interparticle bonding effect. The enhanced effective stress and bonding variable are selected as constitutive variables. The bonding variable is correlated with the ratio between unsaturated void ratio and saturated void ratio. The deformation characteristics of unsaturated soils are described based on the bounding surface plasticity theory. A soil–water characteristic model that considers deformation and hydraulic hysteresis is integrated into the constitutive model to achieve hydromechanical coupling. The proposed model can effectively describe the hydromechanical coupling characteristics and the meniscus bonding force of unsaturated bimodal structure soils; the model parameters can be easily obtained through routine experiments. The experimental results of unsaturated isotropic compression, the wetting/drying cycle, and unsaturated triaxial shear tests are used to validate the capability of the proposed model.

  相似文献   

20.
A three-dimensional (3D) soil–structure interface model is proposed within the two-mechanism constitutive theory and bounding surface theory originally established for soils. The proposed model has two main characteristics: first, the model is formulated based on two different and superposed deformation mechanisms. The first mechanism is due to the stress ratio increment, and the second is due to the normal stress increment. Each mechanism induces a shear strain component and a normal strain component. The proposed model can be reduced to the conventional single-mechanism interface model. Second, the plastic modulus and stress dilatancy are defined using the bounding surface theory. The plastic flow rule under cyclic loading is modified and assumed to be dependent on both the stress state of the mapping point and the stress reversal loading direction. The proposed model was validated against the available 3D interface tests and was found to satisfactorily reflect the salient features of the interfaces under monotonic and cyclic loading paths with different normal boundaries. The problem in which the elastic normal stiffness in conventional single-mechanism interface models is often underestimated to enhance the simulation performance under varying normal stress conditions is solved by incorporating the second mechanism. And the effect of the second mechanism on the modeling behavior is discussed. The modified plastic flow direction accurately simulates the 3D cyclic shear response, and the difference between the model simulation and test result increases with the number of cycles by use of the plastic flow direction defined in conventional bounding surface theory.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号