首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献，搜索用时 31 毫秒
1.
Three methods that follow the general format of the Seed-Idriss simplified procedure for evaluating liquefaction resistance of soils are compared in this paper. They are compared by constructing relationships between penetration resistance and small-strain shear–wave velocity (VS) implied from cyclic resistance ratio (CRR) curves for the three methods, and by plotting penetration-VS data pairs. The penetration-VS data pairs are from 43 Holocene-age sand layers in California, South Carolina, Canada, and Japan. It is shown that the VS-based CRR curve is more conservative than CRR curves based on the Standard Penetration Test (SPT) and Cone Penetration Test (CPT), for the compiled Holocene data. This result agrees with the findings of a recent probability study where the SPT-, CPT-, and VS-based CRR curves were characterized as curves with average probability of liquefaction of 31, 50, and 26%, respectively. New SPT- and CPT-based CRR equations are proposed that provide more consistent assessments of liquefaction potential for the Holocene sand layers considered.  相似文献   

2.
The application of the simplified method for evaluating the liquefaction potential based on shear wave velocity measurements has increased substantially due to its advantages, especially for microzonation of liquefaction potential. In the simplified method, a curve is proposed to correlate the cyclic resistance ratio (CRR) with overburden stress-corrected shear wave velocity (Vs1). However, the uniqueness of this curve for all types of soils is questionable. The objective of this research is to study whether the correlation between CRR and Vs1 is unique or not. Besides, the necessity of developing the soil-specific correlations is also investigated. Based on laboratory test data, a new semi-empirical method is proposed to establish the soil-specific CRR–Vs1 correlation. To validate the proposed method, a number of undrained cyclic triaxial tests along with bender element tests were performed on two types of sands. Similar experimental data for six other types of sands reported in the literature was also compiled. Applying the proposed method, soil-specific CRR–Vs1 correlation curves were developed for these eight types of sands. It is shown that the correlation is not unique for different types of sands and the boundary curve proposed in the available simplified method can only be used as an initial estimation of liquefaction resistance. Finally, using the results of this study as well as previous ones, a chart is suggested to be used in engineering practice showing the conditions for which a detailed soil-specific CRR–Vs1 correlation study needs to be performed.  相似文献   

3.
According to the results of cyclic triaxial tests on Hangzhou sands, a correlation is presented between liquefaction resistance and elastic shear modulus. Material-dependent but independent of confining stress, shows the linear relation of (σd/2)1/2 with Gmax. For its application to different soils, a method proposed by Tokimatsu [Tokimatsu K, Uchida A. Correlation between liquefaction resistance and shear wave velocity. Soils Found 1990:30(2):33–42] is utilized to normalize the shear modulus with respect to minimum void ratio. A simplified equation is established to evaluate the liquefaction potential by shear-wave velocity. The critical shear-wave velocity of liquefaction is in linear relation with 1/4 power of depth and the peak horizontal ground surface acceleration during earthquakes. The equation proposed in this paper is compared with previous methods especially the procedure proposed by Andrus [RD Andrus, KH Stokoe. Liquefaction resistance of soils from shear-wave velocity. J Geotech Geoenviron Eng 2000:126(11):1015–25]. The results show its simplicity and effectiveness when applied to sands, but more validation or modification is needed for its application to sand with higher fines content.  相似文献   

4.
According to the results of cyclic triaxial tests, a linear correlation is presented between liquefaction resistance and elastic shear modulus, which shows the relation of G max (kPa) with (σd/2)1/2(kPa)1/2. When applied to soils from different sites, the correlation can be normalized in reference to its minimum void ratio (e min). Accordingly, an improved method is established to evaluate the liquefaction potential with shear-wave velocity. The critical shear-wave velocity of liquefaction is in linear relation with 1/4 power of depth and the maximum acceleration during earthquakes, which can be used to explain the phenomenon that the possibility of liquefaction decreases with the increment of the depth. Compared with previous methods this method turns out simple and effective, which is also verified by the results of cyclic triaxial tests. Foundation item: State Natural Science Foundation (59678020) and Natural Science Foundation of Zhejiang Province (RC9609).  相似文献   

5.
Semi-empirical procedures for evaluating the liquefaction potential of saturated cohesionless soils during earthquakes are re-examined and revised relations for use in practice are recommended. The stress reduction factor (rd), earthquake magnitude scaling factor for cyclic stress ratios (MSF), overburden correction factor for cyclic stress ratios (Kσ), and the overburden normalization factor for penetration resistances (CN) are discussed and recently modified relations are presented. These modified relations are used in re-evaluations of the SPT and CPT case history databases. Based on these re-evaluations, revised SPT- and CPT-based liquefaction correlations are recommended for use in practice. In addition, shear wave velocity based procedures are briefly discussed.  相似文献   

6.
The seismic performance of four pile‐supported models is studied for two conditions: (i) transient to full liquefaction condition, i.e. the phase when excess pore pressure gradually increases during the shaking; (ii) full liquefaction condition, i.e. defined as the state where the seismically induced excess pore pressure equalises to the overburden stress. The paper describes two complementary analyses consisting of an experimental investigation, carried out at normal gravity on a shaking table, and a simplified numerical analysis, whereby the soil–structure interaction (SSI) is modelled through non‐linear Winkler springs (commonly known as p–y curves). The effects of liquefaction on the SSI are taken into account by reducing strength and stiffness of the non‐liquefied p–y curves by a factor widely known as p‐multiplier and by using a new set of p–y curves. The seismic performance of each of the four models is evaluated by considering two different criteria: (i) strength criterion expressed in terms of bending moment envelopes along the piles; (ii) damage criterion expressed in terms of maximum global displacement. Comparison between experimental results and numerical predictions shows that the proposed p–y curves have the advantage of better predicting the redistribution of bending moments at deeper elevations as the soil liquefies. Furthermore, the proposed method predicts with reasonable accuracy the displacement demand exhibited by the models at the full liquefaction condition. However, disparities between computed and experimental maximum bending moments (in both transient and full liquefaction conditions) and displacement demands (during transient to liquefaction condition) highlight the need for further studies. Copyright © 2016 The Authors Earthquake Engineering & Structural Dynamics Published by John Wiley & Sons Ltd.  相似文献   

7.
This paper is a systematic effort to clarify why field liquefaction charts based on Seed and Idriss׳ Simplified Procedure work so well. This is a necessary step toward integrating the states of the art (SOA) and practice (SOP) for evaluating liquefaction and its effects. The SOA relies mostly on laboratory measurements and correlations with void ratio and relative density of the sand. The SOP is based on field measurements of penetration resistance and shear wave velocity coupled with empirical or semi-empirical correlations. This gap slows down further progress in both SOP and SOA. The paper accomplishes its objective through: a literature review of relevant aspects of the SOA including factors influencing threshold shear strain and pore pressure buildup during cyclic strain-controlled tests; a discussion of factors influencing field penetration resistance and shear wave velocity; and a discussion of the meaning of the curves in the liquefaction charts separating liquefaction from no liquefaction, helped by recent full-scale and centrifuge results. It is concluded that the charts are curves of constant cyclic strain at the lower end (Vs1<160 m/s), with this strain being about 0.03–0.05% for earthquake magnitude, Mw≈7. It is also concluded, in a more speculative way, that the curves at the upper end probably correspond to a variable increasing cyclic strain and Ko, with this upper end controlled by overconsolidated and preshaken sands, and with cyclic strains needed to cause liquefaction being as high as 0.1–0.3%. These conclusions are validated by application to case histories corresponding to Mw≈7, mostly in the San Francisco Bay Area of California during the 1989 Loma Prieta earthquake.  相似文献   

8.
Flow liquefaction and cyclic mobility are two different phenomena that are encountered during strong earthquakes. Flow liquefaction is associated with the contractive behavior of loose granular materials and cyclic mobility is associated with the dilative response of both loose and dense granular materials at low confining stresses. These two types of response pertain to the same material and therefore should be modeled in a consistent manner. Whether a soil in a given state exhibits contractive or dilative behavior is dependent on its dilatancy, d=dvp/dqp. A form of the dilatancy d=d(η,ψ,C) is proposed, where η=q/p is the stress ratio, and ψ and C denote the internal state variables and the intrinsic properties, respectively. It has been shown that such a state-dependent dilatancy is effective in describing both the contractive and dilative behavior. This allows the soil behavior associated with flow liquefaction and cyclic mobility during earthquakes to be modeled in a unified way.  相似文献   

9.
The liquefaction behavior and cyclic resistance ratio (CRR) of reconstituted samples of non-plastic silt and sandy silts with 50% and 75% silt content are examined using constant-volume cyclic and monotonic ring shear tests along with bender element shear wave velocity (Vs) measurements. Liquefaction occurred at excess pore water pressure ratios (ru) between 0.6 and 0.7 associated with cumulative cyclic shear strains (γ) of 4% to 7%, after which cyclic liquefaction ensued with very large shear strains and excess pore water pressure ratio (ru>0.8). The cyclic ring shear tests demonstrate that cyclic resistance ratio of silt and sandy silts decreases with increasing void ratio, or with decreasing silt content at a certain void ratio. The results also show good agreement with those from cyclic direct simple shear tests on silts and sandy silts. A unique correlation is developed for estimating CRR of silts and sandy silts (with more than 50% silt content) from stress-normalized shear wave velocity measurements (Vs1) with negligible effect of silt content. The results indicate that the existing CRR–Vs1 correlations would underestimate the liquefaction resistance of silts and sandy silt soils.  相似文献   

10.
Three groups of dynamic triaxial tests were performed for saturated Nanjing fine sand subjected to uniform cyclic loading. The tested curves of the excess pore water pressure (EPWP) ratio variation with the ratio of the number of cycles are provided. The concept of the EPWP increment ratio is introduced and two new concepts of the effective dynamic shear stress ratio and the log decrement of effective stress are defined. It is found that the development of the EPWP increment ratio can be divided into three stages: descending, stable and ascending. Furthermore, at the stable and ascending stages, a satisfactory linear relationship is obtained between the accumulative EPWP increment ratio and natural logarithm of the effective dynamic shear stress ratio. Accordingly, the EPWP increment ratio at the number of cycles N has been deduced that is proportional to the log decrement of effective stress at the cycle number N-1, but is independent of the cyclic stress amplitude. Based on the analysis, a new EPWP increment model for saturated Nanjing fine sand is developed from tested data fitting, which provides a better prediction of the curves of EPWP generation, the number of cycles required for initial liquefaction and the liquefaction resistance.  相似文献   

11.

In engineering practice, the liquefaction potential of a sandy soil is usually evaluated with a semi-empirical, stress-based approach computing a factor of safety in free field conditions, defined as the ratio between the liquefaction resistance (capacity) and the seismic demand. By so doing, an estimate of liquefaction potential is obtained, but nothing is known on the pore pressure increments (often expressed in the form of normalized pore pressure ratio ru) generated by the seismic action when the safety factor is higher than 1. Even though ru can be estimated using complex numerical analyses, it would be extremely useful to have a simplified procedure to estimate them consistent with the stress-based approach adopted to check the safety conditions. This paper proposes such a procedure with reference to both saturated and unsaturated soils, considering the latter as soils for which partial saturation has been artificially generated with some ground improvement technology to increase cyclic strength and thus tackle liquefaction risk. A simple relationship between the liquefaction free field safety factor FS, and ru(Sr) is introduced, that generalizes a previous expression proposed by Chiaradonna and Flora (Geotech Lett, 2020. https://doi.org/10.1680/jgele.19.00032) for saturated soils. The new procedure has been successfully verified against some experimental data, coming from laboratory constant amplitude cyclic tests and from centrifuge tests with irregular acceleration time histories for soils having different gradings and densities.

  相似文献   

12.
Contrary to many laboratory investigations, common empirical correlations from in situ tests consider that the increase in the percentage of fines leads to an increase of the cyclic liquefaction resistance of sands. This paper draws upon the integrated Critical State Soil Mechanics framework in order to study this seemingly not univocal effect. Firstly the effect of fines on the Critical State Line (CSL) is studied through a statistical analysis of a large data set of published monotonic triaxial tests. The results show that increasing the content of non-plastic fines practically leads to a clockwise rotation of the CSL in (e–ln p) space. The implication of this effect on cyclic liquefaction resistance is subsequently evaluated with the aid of a properly calibrated critical state elasto-plastic constitutive model, as well as a large number of published experimental results and in situ empirical correlations. Both sets of data show clearly that a fines content, less than about 30% by weight, may prove beneficial at relatively small effective stresses (p0<50–70 kPa), such as the in situ stresses prevailing in most liquefaction case studies, and detrimental at larger confining stresses, i.e. the stresses usually considered in laboratory tests. To the extent of these findings, a correction factor is proposed for the practical evaluation of liquefaction resistance in terms of the fines content and the mean effective confining stress.  相似文献   

13.
Field investigations following the 2008 Ms8.0 Wenchuan earthquake identified 118 liquefaction sites, most of which are underlain by gravelly sediment in the Chengdu Plain and adjacent Mianyang area, in the Sichuan Province. Gravel sediment in the Sichuan province is widely distributed; hence it is necessary to develop a method for prediction and evaluation of gravel liquefaction behavior. Based on liquefaction investigation data and in-situ testing, and with reference to existing procedures for sandy soil liquefaction evaluation, a fundamental procedure for gravel liquefaction evaluation using dynamic penetration tests (DPT) is proposed along with a corresponding model and calculation formula. The procedure contains two stages, i.e., pre-determination and re-determination. Pre-determination excludes impossible liquefiable or non-liquefiable soils, and re-determination explores a DPT-based critical N120 blows calculation model. Pre-determination includes three criteria, i.e., geological age, gravel contents, gravel sediment depths and water tables. The re-determination model consists of five parameters, i.e., DPT reference values, gravel contents, gravel sediment depths, water tables and seismic intensities. A normalization method is used for DPT reference values and an optimization method is used for the gravel sediment depth coefficient and water table coefficient. The gravel liquefaction evaluation method proposed herein is simple and takes most influencing factors on gravel sediment liquefaction into account.  相似文献   

14.
采用MTS810动三轴试验仪,用二氧化碳+脱气水循环渗流法对重塑黄土进行饱和,进行了一系列对石碑塬滑坡区饱和黄土液化后变形特性试验。考虑干密度和初始有效围压对黄土液化后变形特性的影响,将液化与未液化黄土在单调静荷载作用下的应力-应变曲线进行对比。实验结果表明:利用二氧化碳+脱气水循环渗流法可以使重塑黄土饱和取得较好的效果;饱和石碑塬黄土具有明显的液化特征,在强震作用下发生液化,液化后强度大大衰减,应力-应变曲线呈弱硬化型,分为两个阶段;干密度和初始有效围压对液化后黄土的强度有一定影响,初始有效围压与不排水强度呈拟合度较高的线性关系,初始有效围压越高,液化后不排水强度越大。  相似文献   

15.
Model results for the ionospheric E region: solar and seasonal changes   总被引：5，自引：0，他引：5  
A new, empirical model for NO densities is developed, to include physically reasonable variations with local time, season, latitude and solar cycle. Model calculations making full allowance for secondary production, and ionising radiations at wavelengths down to 25 Å, then give values for the peak density N mE that are only 6% below the empirical IRI values for summer conditions at solar minimum. At solar maximum the difference increases to 16%. Solar-cycle changes in the EUVAC radiation model seem insufficient to explain the observed changes in N mE, with any reasonable modifications to current atmospheric constants. Hinteregger radiations give the correct change, with results that are just 2% below the IRI values throughout the solar cycle, but give too little ionisation in the E-F valley region. To match the observed solar increase in N mE, the high-flux reference spectrum in the EUVAC model needs an overall increase of about 20% (or 33% if the change is confined to the less well defined radiations at <150 Å). Observed values of N mE show a seasonal anomaly, at mid-latitudes, with densities about 10% higher in winter than in summer (for a constant solar zenith angle). Composition changes in the MSIS86 atmospheric model produce a summer-to-winter change in N mE of about–2% in the northern hemisphere, and +3% in the southern hemisphere. Seasonal changes in NO produce an additional increase of about 5% in winter, near solar minimum, to give an overall seasonal anomaly of 8% in the southern hemisphere. Near solar maximum, reported NO densities suggest a much smaller seasonal change that is insufficient to produce any winter increase in N mE. Other mechanisms, such as the effects of winds or electric fields, seem inadequate to explain the observed change in N mE. It therefore seems possible that current satellite data may underestimate the mean seasonal variation in NO near solar maximum. A not unreasonable change in the data, to give the same 2:1 variation as at solar minimum, can produce a seasonal anomaly in NmE that accounts for 35–70% of the observed effect at all times.  相似文献   

16.
目前,主要依靠室内动力试验对黄土液化势进行评价。由于黄土特殊的结构性,室内试验对其饱和的过程较为复杂,且与实际场地饱和黄土差异明显,导致室内黄土液化试验结果并不能代表现场饱和黄土的抗液化强度。本文选取兰州市西固区寺儿沟村某饱和黄土场地进行钻孔测试,现场实施了标准贯入试验、静力触探试验以及剪切波速测试。应用Robertson的土类指数分类图对该场地不同含水率黄土的土类进行了界定,确定了饱和黄土属于类砂土,有液化势。应用NCEER推荐方法,计算了3组原位试验数据的饱和黄土循环抗力比（CRR）,通过与1976年唐山地震和1999年集集地震液化土CRR对比,得出了饱和黄土抗液化强度很低的结论。  相似文献   

17.
Whether the presence of non-plastic silt in a granular mix soil impact its liquefaction potential and how to evaluate liquefaction resistance of sand containing different amounts of silt contents are both controversial issues. This paper presents the results of an experimental evaluation to address these issues. Two parameters, namely, equivalent intergranular void ratio （ec）eq and equivalent interfine void ratio （ef）eq, proposed in a companion paper （Thevanayagam, 2007） as indices of active grain contacts in a granular mix, are used to characterize liquefaction resistance of sands and silty sands. Results indicate that, at the same global void ratio （e）, liquefaction resistance of silty sand decreases with an increase in fines content （Cv） up to a threshold value （Crth）. This is due to a reduction in intergrain contact density between the coarse grains. Beyond Crth, with further addition of fines, the interfine contacts become significant while the inter-coarse grain contacts diminish and coarse grains become dispersed. At the same e, the liquefaction resistance increases and the soil becomes stronger with a fttrther increase in silt content. Beyond a limiting fines content （CrL）, the liquefaction resistance is controlled by interfine contacts only. When Cr〈Crth, at the same （e）eq, the liquefaction resistance of silty sand is comparable to that of the host clean sand at a void ratio equal to （ec）eq. When CF〉CFth, at the same （ef）eq, the cyclic strength of a sandy silt is comparable to the host silt at a void ratio equal to （ef）eq.  相似文献   

18.
含弱渗透性覆盖层饱和砂土地震液化特性研究   总被引：2，自引：0，他引：2       下载免费PDF全文
针对含弱渗透性覆盖层的饱和砂土地基进行一组离心机振动台试验,并采用OpenSees对试验模型进行数值模拟。通过模型试验与数值模拟结果对比讨论OpenSees对于饱和砂土地基地震液化模拟的精度;采用水平方向的Arias强度表示传入某一位置的地震动强度,并以液化时水平方向Arias强度作为该土层的抗液化强度;采用OpenSees计算不同地震动输入时饱和砂土的反应,以此检验Arias强度作为抗液化强度的准确性。结果表明,引起饱和砂土液化所需要的地震动强度随深度增加而增加;当传入的地震强度达到砂土发生液化所需要的地震强度时,该层砂土将会发生液化。  相似文献   

19.
The aim of the present study is twofold. Firstly, the paper investigates the undrained cyclic and post-cyclic behaviour of two silica sands by means of multi-stage cyclic triaxial tests. Secondly, based on the post-cyclic response observed in the element test, the authors formulate a simplified stress–strain relationship that can be conveniently used for the construction of p–y curves for liquefiable soils. The multi-stage loading condition consists of an initial cyclic loading applied to cause liquefaction, followed by undrained monotonic loading that aimed to investigate the post-cyclic response of the liquefied sample. It was found that due to the tendency of the liquefied soil to dilate upon undrained shearing, the post-liquefaction strain–stress response was characterised by a distinct strain–hardening behaviour. The latter is idealized by means of a bi-linear stress–strain model, which can be conveniently formulated in terms of three parameters, i.e.: (i) take-off shear strain, γto, i.e. shear strain required to mobilize 1 kPa of shear strength; (b) initial secant shear modulus, G1, defined as 1/γto; (c) post-liquefied shear modulus at large strain, G2 (γ⪢γto). Based on the experimental results, it is concluded that these parameters are strongly influenced by the initial relative density of the sample, whereby γto decreases with increasing relative density. Differently both shear moduli (G1 and G2) increases with increasing relative density. Lastly, the construction of new p–y curves for liquefiable soils based on the idealized bi-linear model is described.  相似文献   

20.
Gravelly soil is generally recognized to have no liquefaction potential. However, liquefaction cases were reported in central Taiwan in the 1999 Chi-Chi Taiwan earthquake and in the 1988 Armenia earthquake. Thus, further studies on the liquefaction potential of gravelly soil are warranted. Because large particles can impede the penetration of both standard penetration test and cone penetration test, shear wave velocity-based correlations and large hammer penetration tests (LPT) are employed to evaluate the liquefaction resistance of gravelly soils. A liquefied gravelly deposit site during the Chi-Chi earthquake was selected for this research. In situ physical properties of soil deposits were collected from exploratory trenches. Instrumented LPT and shear wave velocity (Vs) measurements were performed to evaluate the liquefaction resistance. In addition, large-scale cyclic triaxial tests on remolded gravelly soil samples (15 cm in diameter, 30 cm in height) were conducted to verify and improve LPT-based and Vs-based correlations. The results show that the LPT and shear wave velocity methods are reasonably suitable for liquefaction assessment of gravelly soils.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号