首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献，搜索用时 31 毫秒
1.
This study examined the molecular and isotopic compositions of gases generated from different kerogen types (i.e., Types I/II, II, IIS and III) in Menilite Shales by sequential hydrous pyrolysis experiments. The experiments were designed to simulate gas generation from source rocks at pre-oil-cracking thermal maturities. Initially, rock samples were heated in the presence of liquid water at 330 °C for 72 h to simulate early gas generation dominated by the overall reaction of kerogen decomposition to bitumen. Generated gas and oil were quantitatively collected at the completion of the experiments and the reactor with its rock and water was resealed and heated at 355 °C for 72 h. This condition simulates late petroleum generation in which the dominant overall reaction is bitumen decomposition to oil. This final heating equates to a cumulative thermal maturity of 1.6% Rr, which represents pre-oil-cracking conditions. In addition to the generated gases from these two experiments being characterized individually, they are also summed to characterize a cumulative gas product. These results are compared with natural gases produced from sandstone reservoirs within or directly overlying the Menilite Shales. The experimentally generated gases show no molecular compositions that are distinct for the different kerogen types, but on a total organic carbon (TOC) basis, oil prone kerogens (i.e., Types I/II, II and IIS) generate more hydrocarbon gas than gas prone Type III kerogen. Although the proportionality of methane to ethane in the experimental gases is lower than that observed in the natural gases, the proportionality of ethane to propane and i-butane to n-butane are similar to those observed for the natural gases. δ13C values of the experimentally generated methane, ethane and propane show distinctions among the kerogen types. This distinction is related to the δ13C of the original kerogen, with 13C enriched kerogen generating more 13C enriched hydrocarbon gases than kerogen less enriched in 13C. The typically assumed linear trend for δ13C of methane, ethane and propane versus their reciprocal carbon number for a single sourced natural gas is not observed in the experimental gases. Instead, the so-called “dogleg” trend, exemplified by relatively 13C depleted methane and enriched propane as compared to ethane, is observed for all the kerogen types and at both experimental conditions. Three of the natural gases from the same thrust unit had similar “dogleg” trends indicative of Menilite source rocks with Type III kerogen. These natural gases also contained varying amounts of a microbial gas component that was approximated using the Δδ13C for methane and propane determined from the experiments. These approximations gave microbial methane components that ranged from 13–84%. The high input of microbial gas was reflected in the higher gas:oil ratios for Outer Carpathian production (115–1568 Nm3/t) compared with those determined from the experiments (65–302 Nm3/t). Two natural gas samples in the far western part of the study area had more linear trends that suggest a different organic facies of the Menilite Shales or a completely different source. This situation emphasizes the importance of conducting hydrous pyrolysis on samples representing the complete stratigraphic and lateral extent of potential source rocks in determining specific genetic gas correlations.  相似文献   

2.
Steroids with unconventional side chains have increasingly been applied as diagnostic markers for geological source and age assessments. However, one of the most distinctive characteristics, the abnormal abundance of pregnane and homopregnane in ancient sediments and petroleum, remains unresolved. Higher pregnane and homopregnane, as well as C23–C26 20-n-alkylpregnanes, relative to the regular steranes were observed in samples collected from different petroleum basins in China. These included Precambrian marine carbonate-derived petroleum (NW Sichuan Basin), Lower Paleozoic marine marl derived crude oils (Tarim Basin), and Eocene hypersaline lacustrine carbonate source rocks and associated petroleum (Bohai Bay Basin). However, all of the samples have many common biomarker characteristics, such as pristane/phytane ratios < 1, low amounts of diasteranes and high C29/C30 hopane (∼0.6–1), C35/C34 hopane (mostly ⩾ 1) and dibenzothiophene/phenanthrene (DBT/PHEN, mostly 0.5–1) ratios revealing a contribution from anoxic carbonate/marl source rocks deposited in restricted, clastic-starved settings. We suggest that 5α,l4β,l7β-pregnane and homopregnane, as well as their higher C23–C26 homologues, are geological products derived from steroids bound to the kerogen by a sulfurized side chain. Carbon or carbonate minerals are considered to be natural catalysts for this cracking reaction via preferential cleavage of the bond between C-20 and C-22. Similar distributions occur in the short chain analogues of 4-methylsterane, triaromatic steroid and methyltriaromatic steroid hydrocarbons, providing circumstantial evidence for this proposal. The ratio of pregnane and homopregnane to the total regular steranes and the ratio of C27 diasteranes to cholestanes can be sensitive indicators of sedimentary environments and facies. In general, high diasteranes and low pregnanes (with homologues) indicate an oxic water column or significant input of terrigenous organic matter in clay rich source rocks and some organic lean carbonate rocks. Low diasteranes with high pregnanes implies restricted, sulfur rich conditions, typical of anoxic carbonate source rocks. Furthermore, the two ratios may be useful to assess the variation of mineralogy and openness of source rock depositional settings.  相似文献   

3.
The Menilite Shales (Oligocene) of the Polish Carpathians are the source of low-sulfur oils in the thrust belt and some high-sulfur oils in the Carpathian Foredeep. These oil occurrences indicate that the high-sulfur oils in the Foredeep were generated and expelled before major thrusting and the low-sulfur oils in the thrust belt were generated and expelled during or after major thrusting. Two distinct organic facies have been observed in the Menilite Shales. One organic facies has a high clastic sediment input and contains Type-II kerogen. The other organic facies has a lower clastic sediment input and contains Type-IIS kerogen. Representative samples of both organic facies were used to determine kinetic parameters for immiscible oil generation by isothermal hydrous pyrolysis and S2 generation by non-isothermal open-system pyrolysis. The derived kinetic parameters showed that timing of S2 generation was not as different between the Type-IIS and -II kerogen based on open-system pyrolysis as compared with immiscible oil generation based on hydrous pyrolysis. Applying these kinetic parameters to a burial history in the Skole unit showed that some expelled oil would have been generated from the organic facies with Type-IIS kerogen before major thrusting with the hydrous-pyrolysis kinetic parameters but not with the open-system pyrolysis kinetic parameters. The inability of open-system pyrolysis to determine earlier petroleum generation from Type-IIS kerogen is attributed to the large polar-rich bitumen component in S2 generation, rapid loss of sulfur free-radical initiators in the open system, and diminished radical selectivity and rate constant differences at higher temperatures. Hydrous-pyrolysis kinetic parameters are determined in the presence of water at lower temperatures in a closed system, which allows differentiation of bitumen and oil generation, interaction of free-radical initiators, greater radical selectivity, and more distinguishable rate constants as would occur during natural maturation. Kinetic parameters derived from hydrous pyrolysis show good correlations with one another (compensation effect) and kerogen organic-sulfur contents. These correlations allow for indirect determination of hydrous-pyrolysis kinetic parameters on the basis of the organic-sulfur mole fraction of an immature Type-II or -IIS kerogen.  相似文献   

4.
《Applied Geochemistry》2005,20(10):1875-1889
Based on the systematic analyses of light hydrocarbon, saturate, aromatic fractions and C isotopes of over 40 oil samples along with related Tertiary source rocks collected from the western Qaidam basin, the geochemical characteristics of the Tertiary saline lacustrine oils in this region was investigated. The oils are characterized by bimodal n-alkane distributions with odd-to-even (C11–C17) and even-to-odd (C18–C28) predominance, low Pr/Ph (mostly lower than 0.6), high concentration of gammacerane, C35 hopane and methylated MTTCs, reflecting the high salinity and anoxic setting typical of a saline lacustrine depositional environment. Mango’s K1 values in the saline oils are highly variable (0.99–1.63), and could be associated with the facies-dependent parameters such as Pr/Ph and gammacerane indexes. Compared with other Tertiary oils, the studied Tertiary saline oils are marked by enhanced C28 sterane abundance (30% or more of C27–C29 homologues), possibly derived from halophilic algae. It is noted that the geochemical parameters of the oils in various oilfields exhibit regular spatial changes, which are consistent with the depositional phase variations of the source rocks. The oils have uncommon heavy C isotopic ratios (−24‰ to −26‰) and a flat shape of the individual n-alkane isotope profile, and show isotopic characteristics similar to marine organic matter. The appearance of oleanane and high 24/(24 + 27)-norcholestane ratios (0.57–0.87) in the saline oils and source rocks confirm a Tertiary organic source.  相似文献   

5.
Biomarker and n-alkane compound specific stable carbon isotope analyses (CSIA) were carried out on 58 crude oil samples from shallow water and deepwater fields of the Niger Delta in order to predict the depositional environment and organic matter characteristics of their potential source rocks. Using a source organofacies prediction approach from oil geochemistry, the presence in the western deepwater oils relatively abundant C27 steranes, C30 24-n-propyl cholestane, low oleanane index, relatively low pr/ph ratios, gammacerane, and positive to nearly flat C12–C30 n-alkane compound specific stable carbon isotope profiles, suggests that the source facies that expelled these oils contain significant marine derived organic matter deposited under sub-oxic and stratified water column conditions. This contrasts with the terrigenous organic matter dominated source rocks accepted for shallow water Niger Delta oils. Oils in the shallow water accumulations can be separated into terrigenous and mixed marine-terrigenous families. The terrigenous family indicates expulsion from source rock(s) containing overwhelmingly higher plant source organic matter (average oleanane index = 0.48, high C29 steranes) as well as having negative sloping n-alkane isotope profiles. Oxic source depositional conditions (pr/ph > 2.5) and non-stratified conditions (absence to low gammacerane content) are inferred for the terrigenous family. The mixed marine-terrigenous family has biomarker properties that are a combination of the deepwater and terrigenous shallow water oils. Bitumen extracts of the sub-delta Late Cretaceous Araromi Formation shale in the Dahomey Basin are comparable both molecularly and isotopically to the studied western deepwater oil set, but with an over all poor geochemical correlation. This poor geochemical match between Araromi shale and the western deepwater oils does not downgrade the potential of sub-delta Cretaceous source rock contribution to the regional oil charge in the deepwater Niger Delta.  相似文献   

6.
Acquiring crude oils that have been expelled from the same rock unit at different levels of thermal maturation is currently not feasible in the natural system. This prevents direct correlation of compositional changes between the organic matter retained in a source rock and its expelled crude oil at different levels of thermal maturation. Alleviation of this deficiency in studying the natural system requires the use of laboratory experiments. Natural generation of petroleum from amorphous type-II kerogen in the Woodford Shale may be simulated by hydrous pyrolysis, which involves heating crushed rock in contact with water at subcritical temperatures (<374°C). Four distinct stages of petroleum generation are observed from this type of pyrolysis; (1) pre-oil generation, (2) incipient-oil generation, (3) primary-oil generation, and (4) post-oil generation.The effects of thermal maturation on the δ13C values of kerogen, bitumen, and expelled oil-like pyrolysate from the Woodford Shale have been studied through these four stages of petroleum generation. Similar to the natural system, the kerogens isolated from the pyrolyzed rock showed no significant change in δ13C. This suggests that the δ13C value of kerogens may be useful in kerogen typing and oil-to-source rock correlations. δ13C values of bitumens extracted from the pyrolyzed rock showed an initial decrease during the incipient-oil generation stage, followed by depletion during the primary- and post-oil generation stages. This reversal is not favorable for geochemical correlation or maturity evaluation. Saturated and polar components of the bitumen show the greatest δ13C variations with increasing thermal maturation. The difference between the δ13C of these two components gives a unidirectional trend that serves as a general indicator of thermal maturation and is referred to as the bitumen isotope index (BII).δ13C values of the expelled pyrolysates show a unidirectional increase with increasing thermal maturation. The constancy and similarity of δ13C values of the aromatic components in the expelled pyrolysates and bitumens, with increasing thermal maturation, encourages their use in oil-to-oil and oil-to-source rock correlations. Isotopic type-curves for expelled pyrolysates indicate that they may be useful in oil-to- oil correlations, but have a limited use in oil-to-source rock correlations.  相似文献   

7.
Calcite veins with fluid and solid bitumen inclusions have been discovered in the south-western shoulder of the Dead Sea rift within the Masada-Zohar block, where hydrocarbons exist in small commercial gas fields and non-commercial fields of heavy and light oils. The gas–liquid inclusions in calcite are dominated either by methane or CO2, and aqueous inclusions sometimes bear minor dissolved hydrocarbons. The enclosed flake-like solid bitumen matter is a residue of degraded oil, which may be interpreted as “dead carbon”. About 2/3 of this matter is soot-like amorphous carbon and 1/3 consists of n-C8C18 carboxylic acids and traces of n-alkanes, light dicarboxylic acids, and higher molecular weight (>C20) branched and/or cyclic carboxylic acids. Both bitumen and the host calcites show genetic relationship with mature Maastrichtian chalky source rocks (MCSRs) evident in isotopic compositions (δ13C, δ34S, and δ18O) and in REE + Y patterns. The bitumen precursor may have been heavy sulfur-rich oil which was generated during the burial compaction of the MCSR strata within the subsided blocks of the Dead Sea graben. The δ18O and δ13C values and REE + Y signatures in calcites indicate mixing of deep buried fluids equilibrated with post-mature sediments and meteoric waters. The temperatures of fluid generation according to Mg–Li-geothermometer data range from 55 °С to 90 °С corresponding to the 2.5–4.0 km depths, and largely overlap with the oil window range (60–90 °С) in the Dead Sea rift (Hunt, 1996; Gvirtzman and Stanislavsky, 2000; Buryakovsky et al., 2005). The bitumen-rich vein calcites originated in the course of Late Cenozoic rifting and related deformation, when tectonic stress triggers damaged small hydrocarbon reservoirs in the area, produced pathways, and caused hydrocarbon-bearing fluids to rise to the subsurface; the fluids filled open fractures and crystallized to calcite with entrapped bitumen. The reported results are in good agreement with the existing views of maturation, migration, and accumulation of hydrocarbons, as well as basin fluid transport processes in the Dead Sea area.  相似文献   

8.
The mudstones in the third member of the Shahejie Formation (Es3) are the primary source rocks in the Banqiao Depression of Bohai Bay Basin. They are rich in organic matter with Total Organic Carbon (TOC) content up to 3.5%. The sandstones in the Es3 member are the deepest proven hydrocarbon reservoir rocks with measured porosity and permeability values ranging from 3.6% to 32.4% and from 0.01 md to 3283.7 md, respectively. One, two and three-dimensional basin modelling studies were performed to analyse the petroleum generation and migration history of the Es3 member in the Banqiao Depression based on the reconstruction of the burial, thermal and maturity history in order to evaluate the remaining potential of this petroleum province. The modelling results are calibrated with measured vitrinite reflectance (Ro), borehole temperatures and some drilling results of 63 wells in the study area. Calibration of the model with thermal maturity and borehole temperature data indicates that the present-day heat flow in the Banqiao Depression varies from 59.8 mW/m2 to 61.7 mW/m2 and the paleo-heat flow increased from 65 Ma to 50.4 Ma, reached a peak heat-flow values of approximately 75 mW/m2 at 50.4 Ma and then decreased exponentially from 50.4 Ma to present-day. The source rocks of the Es3 member are presently in a stage of oil and condensate generation with maturity from 0.5% to 1.8% Ro and had maturity from 0.5% to 1.25% Ro at the end of the Dongying Formation (Ed) deposition (26 Ma). Oil generation (0.5% Ro) in the Es3 member began from about 37 Ma to 34 Ma and the peak hydrocarbon generation (1.0% Ro) occurred approximately from 30 Ma to 15 Ma. The modelled hydrocarbon expulsion evolution suggested that the timing of hydrocarbon expulsion from the Es3 member source rocks began from 31 Ma to 10 Ma with the peak hydrocarbon expulsion shortly after 26 Ma. Secondary petroleum migration pathways in the Es3 member of the Banqiao Depression are modelled based on the structure surfaces at 26 Ma and present-day, respectively. The migration history modelling results have accurately predicted the petroleum occurrences within the Es3 member of the Banqiao Depression based on the calibration with drilling results of 10 oil-producing wells, one well with oil shows and 52 dry holes. Six favorable zones of oil accumulations in the Es3 member of the Banqiao Depression are identified especially oil accumulation zones I and II due to their proximity to the generative kitchens, short oil migration distances and the presence of a powerful drive force.  相似文献   

9.
Although the effects of biodegradation on the composition and physical properties of crude oil have been well studied, effects of in-reservoir petroleum biodegradation on molecular and isotopic compositions of crude oils are not yet clearly understood. The Alberta Basin, in western Canada, is one of the world’s largest petroleum accumulations and constitutes an ideal example of a natural suite of sequentially biodegraded oils. The basin hosts moderately to severely biodegraded petroleum, regionally distributed and in single, more or less continuous, oil columns. In this study, a series of oil samples from the Alberta heavy oil and oil sands provinces, with varying degrees of biodegradation, were analyzed to assess the impact of progressive biodegradation on the molecular and C, H, N, and S isotopic compositions of oils. The results of the molecular characterization of the hydrocarbon fraction of the studied oils show that the oils have suffered biodegradation levels from 2 to 10+ (toward the Alberta–Saskatchewan border) on the Peters and Moldowan scale of biodegradation (abbreviated PM 2 to PM 10) and from tens to hundreds on the Manco scale. Within single reservoirs, increasing biodegradation was observed from top to bottom of the oil columns at all sites studied. The whole oil stable isotopic compositions of the samples varied in the ranges δ13C = −31.2‰ to −29.0‰, δ2H = −147‰ to −133‰, δ15N = 0.3–4.7‰ and δ34S = 0.4–6.4‰. The maximum differences between δ values of samples (Δ) within single oil columns were Δ13C = 1.4‰, Δ2H = 7‰, Δ15N = 1.7‰ and Δ34S = 1.0‰. Regional variations in the isotopic compositions of oil samples from different wells (averaged values from top to bottom) were 1.2‰ for δ13C, 12‰ for δ2H, 4.1‰ for δ15N and 5.5‰ for δ34S and hence generally significantly larger variations were seen than variations observed within single oil columns, especially for N and S. It appears that even severe levels of biodegradation do not cause observable systematic variations in carbon, nitrogen or sulfur isotope composition of whole oils. This indicates that sulfur and nitrogen isotopic compositions may be used in very degraded oils as indicators for oil charge from different source rock facies.  相似文献   

10.
Three sets of pyrolysis experiments were performed on extracted coal (Ro% 0.39), coal (initial bitumen 13.5 mg/g coal) and bitumen enriched coal (total bitumen 80.9 mg/g coal) at two heating rates of 2 °C/h and 20 °C/h in confined systems (gold capsules). For all three experiments, the yields of bitumen, Σn-C8+, aromatic components and ΣC2–5 at first increase and then decrease with increasing EASY%Ro and reach the highest values within the EASY%Ro ranges of 0.67–1.08, 1.07–1.19, 1.46–1.79 and 1.46–1.68, respectively. In contrast, C1/ΣC1–5 ratio at first decreases and then increases with EASY%Ro and reaches a minimum value in EASY%Ro range of 0.86–1.08, closely corresponding to the maximum values of the yields of bitumen and Σn-C8+. Methane yields increase consistently with EASY%Ro. Nearly half of the maximum yield of methane from kerogen was generated at EASY%Ro > 2.2. The differences in methane yields among the three experiments at the same thermal stress are relatively minor at EASY%Ro < 2.2, but are greater with thermal stress at EASY%Ro > 2.2. This demonstrates that the kerogen always retained relatively more hydrogen and hydrocarbon generative potential at the postmature stage of bitumen rich coal than the extracted coal or coal.The maximum yield of ethane is 20–25% higher in the bitumen rich coal experiment than the extracted coal or coal, while the maximum yields of C3, C4 and C5 in the former are double to triple those in the latter. This result demonstrates that the added bitumen in bitumen rich coal substantially increased the generation of these wet gases. However, the averaged values of activation energies (with the same frequency factors) for both the generation and cracking of individual wet gases are similar and do not show consistent trends among the three experiments. For all three experiments, activation energies for the generation and cracking of wet gases are significantly lower than those in previously published oil pyrolysis experiments with same frequency factors (Pan et al., 2012; Organic Geochemistry 45, 29–47). Methane δ13C values at the maximum temperature or EASY%Ro are close to those of initial wet gases, especially C3, implying that the major part of methane shared a common initial precursor with wet gases, i.e., free and bound liquid alkanes.  相似文献   

11.
24-n-Propylcholestane (24-npc), a C30 sterane compound derived from sterol precursors which are the major sterol constituents of modern pelagophyte microalgae, occurs in certain Neoproterozoic rocks and oils and throughout the Phanerozoic rock record. This broad distribution leads 24-npc to be widely considered a reliable indicator of open to partially restricted marine depositional conditions for source rocks and oils. Here we report two significant hiatuses in the occurrences of 24-npc in the Lower Paleozoic marine rock record: the first in the Middle–Late Cambrian and the second in the Late Ordovician–early Silurian transition for a range of lithofacies (carbonates and siliciclastic rocks), organic carbon contents (both organic-lean and organic-rich), and paleoceanographic environments (shelf and deeper water marine settings) and observed offshore of two paleocontinents, Laurentia and Baltica. The Ordovician–Silurian gap is at least 9 million years, and possibly up to 20 million years, in duration. Robust older occurrences of 24-npc steranes in some Neoproterozoic rocks and oils suggest that oceanographic conditions in our intervals of Lower Paleozoic time were unfavorable for the proliferation of pelagophyte algae as phytoplankton. Caution should therefore be applied when interpreting a lacustrine versus marine depositional environmental setting for source rocks and oils in these intervals of Early Paleozoic time using lipid biomarker assemblages.  相似文献   

12.
Unusually high dibenzothiophene (DBT) concentrations are present in the oils from the Tazhong-4 Oilfield in the Tazhong Uplift, Tarim Basin. Positive-ion electrospray ionization Fourier transform ion cyclotron resonance mass spectrometry (FT-ICR MS) was used in combination with conventional geochemical approaches to unravel the enrichment mechanisms. Significant amounts of S1 species with relatively low DBE values (0–8), i.e., sulfur ethers, mercaptans, thiophenes and benzothiophenes, were detected in three Lower Ordovician oils with high thermal maturity, which were suggested to be the products of thermochemical sulfate reduction (TSR) in the reservoir. The occurrence of TSR was also supported by the coexistence of thiadiamondoids and abundant H2S in the gases associated with the oils. Obviously low concentrations of the DBE = 9 S1 species (mainly equivalent to C0–C35 DBTs) compared to its homologues were observed for the three oils which were probably altered by TSR, indicating that no positive relationship existed between TSR and DBTs in this study. The sulfur compounds in the Tazhong-4 oils are quite similar to those in the majority of Lower Ordovician oils characterized by high concentrations of DBTs and dominant DBE = 9 S1 species with only small amounts of sulfur compounds with low thermal stability (DBE = 0–8), suggesting only a small proportion of sulfur compounds were derived from TSR. It is thermal maturity rather than TSR that has caused the unusually high DBT concentrations in most of the Lower Ordovician oils. We suggest that the unusually high DBT oils in the Tazhong-4 Oilfield are caused by oil mixing from the later charged Lower Ordovician (or perhaps even deeper), with high DBT abundances from the earlier less mature oils, which was supported by our oil mixing experiments and previous relevant investigations as well as abundant authigenic pyrite of hydrothermal origin. We believe that TSR should have occurred in the Tazhong Uplift based on our FT-ICR MS results. However, normal sulfur compounds were detected in most oils and no increase of δ13C2H6–δ13C4H10 was observed for the gas hydrocarbons, suggesting only a slight alteration of the oils by TSR currently and/or recently. We suspect that the abnormal sulfur compounds in the Lower Ordovician oils might also be a result of deep oil mixing, which might imply a deeper petroliferous horizon, i.e., Cambrian, with a high petroleum potential. This study is important to further deep petroleum exploration in the area.  相似文献   

13.
The Erlian basin is a continental rift basin located in Inner Mongolia, Northern China. It is a typical representative of Cretaceous Northeast Asian Rift System, which includes many small petroliferous basins in Mongolia Republic and Northern China. Although Lower Cretaceous source rocks are understood to be most important in the Erlian petroleum systems, the precise identification of these source rock intervals and their determination on oil families distribution and composition are poorly understood in this tectonically complicated, nonmarine basin. New bulk data have been gathered from source rock intervals, oil sands and crude oil samples in eight main oil-producing subbasins. Geochemical analyses indicate that Lower Cretaceous Aershan formation (K1ba) and Tengger 1 formation (K1bt1) are two main source intervals in the Erlian basin and their source rock facies vary from profundal lacustrine to marginal lacustrine according to biomarker and trace elements calibration, the profundal lacustrine facies is characterised by brackish water and anoxic environment, which is similar to their correlative oils (Family 1 oils). The marginal lacustrine facies is characterised by freshwater and suboxic environment, which sourced the most common Family 2 oils. Meanwhile, different maturation processes exercise the second control on oil groups and their compositions, the profundal lacustrine source rocks characterised by their sulphur-rich kerogens lead to two oil groups (group 1 and group 2 oils), whose maturity range from low to normal; while, the marginal lacustrine source rock only lead to normal-maturity oils. At last, biodegradation affected the composition of a certain oils and formed group 4 heavy oils. In addition, short migration distance in small subbasins made the contamination or fractionation less notable in the Erlian basin.  相似文献   

14.
Deeply buried heavy oils from the Tabei Uplift of the Tarim Basin have been investigated for their source origin, charge and accumulation time, biodegradation, mixing and thermal cracking using biomarkers, carbon isotopic compositions of individual alkanes, fluid inclusion homogenization temperatures and authigenic illite K–Ar radiometric ages. Oil-source correlation suggests that these oils mainly originated from Middle–Upper Ordovician source rocks. Burial history, coupled with fluid inclusion temperatures and K–Ar radiometric ages, suggests that these oils were generated and accumulated in the Late Permian. Biodegradation is the main control on the formation of these heavy oils when they were elevated to shallow depths during the late Hercynian orogeny. A pronounced unresolved complex mixture (UCM) in the gas chromatograms together with the presence of both 25-norhopanes and demethylated tricyclic terpanes in the oils are obvious evidence of biodegradation. The mixing of biodegraded oil with non-biodegraded oil components was indicated by the coexistence of n-alkanes with demethylated terpanes. Such mixing is most likely from the same phase of generation, but with accumulation at slightly different burial depths, as evidenced by overall similar oil maturities regardless of biodegradation level and/or amount of n-alkanes. Although these Ordovician carbonate reservoirs are currently buried to over 6000 m with reservoir temperatures above 160 °C, no significant secondary hydrocarbon generation from source rocks or thermal cracking of reservoired heavy oil occur in the study area. This is because the deep burial occurred only within the last 5 Ma of the Neogene, and there has not been enough heating time for additional reactions within the Middle–Upper Ordovician source rocks and reservoired heavy oils.  相似文献   

15.
The Bulonggoer paleo-oil reservoir (BPR) on the northwest Junggar Basin is the first Devonian paleo-oil reservoir discovered in North Xinjiang, China. Solid bitumens occur within sandstone pores and as veins filling fractures. Samples of both types were analyzed using stable carbon isotope and reflectance measurements, as well as molecular biomarker parameters.The extremely positive δ13C values and biomarker indicators of depositional environment/lithology, such as pristane/phytane (Pr/Ph), C29/C30 hopane, diasteranes/regular steranes and dibenzothiophene/phenanthrene ratios, indicate a siliciclastic source for the BPR and their deposition in a highly reducing hypersaline environment. The presence of long chain n-alkanes and abundant tetracyclic diterpanes, C20–C21 tricyclic terpanes and perylene are indicators of higher plant organic matter input. Moreover, the bimodal distribution of C27 > C28 < C29 regular steranes and abundant methyltriaromatic steroids also support a contribution of microalgae as well as higher plants organic matter. The similar molecular composition and thermal maturity parameters indicate that the reservoir and veined solid bitumens were altered from a common paleo-petroleum, which originated from peak oil window matured source rocks.All solid bitumens from the BPR are characterized by relatively low bitumen reflectance values (Rb% < 0.7), suggesting that they were generated from low temperature processes rather than oil thermal cracking. Comparatively, the Rb% values for veined bitumens are higher than reservoir bitumens, indicating that the veined bitumens occurred earlier and experienced higher thermal conditions.  相似文献   

16.
Four crude oil samples from the Sergipe–Alagoas Basin, northeastern Brazil, were analyzed using full scan gas chromatography–quadrupole mass spectrometry (GC–qMS) for biomarkers, in order to correlate them using aromatic carotenoids thereby enhancing knowledge about the depositional environment of their source rocks. The geochemical parameters derived from saturated fractions of the oils show evidence of little or no biodegradation and similar thermal maturation (Ts/(Ts + Tm) for terpanes, C29 αββ/(αββ + ααα), C27, and C29 20S/(20S + 20R) for steranes). Low pristane/phytane ratios and the abundance of gammacerane and β-carotane are indicative of an anoxic and saline depositional environment for the source rocks. Moreover, we identified a large range of diagenetic and catagenetic products of the aromatic carotenoid isorenieratene, including C40, C33, and C32 diaryl isoprenoids and aryl isoprenoid derivatives with short side chains and/or additional rings. These results indicate anoxia in the photic zone during the deposition of the source rocks.  相似文献   

17.
The distributions of dimethyldibenzothiophenes (DMDBTs), the relationship between DMDBTs and dimethylbiphenyls (DMBPs), and the applications of DMDBTs as maturity indicators in source rocks have been investigated in a set of 21 lacustrine shales from the Eocene Shahejie Formation (Well SG1) in the Western Depression, Liaohe Basin, China. All source rock samples are characterized by total organic carbon contents of 1.37–3.27% and Type II (with minor Type III) kerogen. They were deposited in suboxic and brackish lacustrine environments and have maturities ranging from immature to mid-mature. The 3,3′-DMBP isomer can potentially react to yield 4,6-DMDBT; 2,6-DMDBT and 2,8-DMDBT by incorporating sulfur into biphenyl, which may be supported by a strong positive correlation between the absolute concentration changes of 3,3′-DMBP and those of 4,6-DMDBT, 2,6-DMDBT plus 2,8-DMDBT. The relative abundance of DMDBT isomers may be explained by the sulfur radical mechanism and are also controlled by steric hindrance and thermodynamic stability. The 4,6-/(1,4- + 1,6)-DMDBT ratio shows no regular trend with increasing maturity at the low stage, and it should be used with caution as a maturity indicator for immature sediments. However, within the oil generation window, the relative concentration of 4,6-DMDBT progressively increases with increasing maturity, which can be explained by its higher thermodynamic stability relative to the 1,4-DMDBT isomer. The 4,6-/(1,4- + 1,6)-DMDBT ratio exhibits a linear increase with increasing thermal maturity of the sediments. Thus, this ratio can be applied as an effective maturity indicator for source rocks within oil generation window.  相似文献   

18.
Thirty-one crude oils and 15 source rocks were selected for molecular geochemical and isotopic analyses in order to establish the genetic relationships between discovered oils and petroleum source rocks in the Weixinan Sub-basin, Beibuwan Basin, South China Sea. Three groups of oils were recognized. Group I oils are only found in the upper section of the Liusagang Formation, with a moderate abundance of C30 4-methylsteranes, low oleanane contents and lighter δ13C values, showing a close relation to the shale occurring in the upper section of the Liusagang Formation. Group II is represented by the majority of the discoveries and is distributed in multi-sets of reservoirs having different ages. The oils are characterized by a high abundance of C30 4-methylsteranes, low to moderate abundance of oleanane and heavy δ13C values, and shows a good correlation with the lacustrine shale and oil shale in the middle section of the Liusagang Formation. Group III oils occurred in the lower section of the Liusagang Formation. The oils have a lower concentration of C30 4-methylsteranes, relatively high abundance of oleananes and their δ13C values are intermediate. Oils of this group correlated well with the shallow lake-delta mudstone of the lower section of Liusagang Formation. These oil-source genetic relationships suggest a strong source facies control on the geographic distribution of oil groups within the Weixinan Sub-basin. The geochemical data indicate shale in the middle section of the Liusagang Formation has an excellent oil generation potential and the lower and upper sections contain dark shale and mudstone with good to fair oil potential. Future exploration or assessment of petroleum potential of the sub-basin could be improved by considering the proposed genetic relationship between the oil types and source rocks, as well as their distribution.  相似文献   

19.
High maturity oil and gas are usually generated after primary oil expulsion from source rocks, especially from oil prone type I/II kerogen. However, the detailed impacts of oil expulsion, or retention in source rock on further thermal degradation of kerogen at the high maturity stage remain unknown. In the present study, we collected an Ordovician Pingliang shale sample containing type II kerogen. The kerogens, which had previously generated and expelled oil and those which had not, were prepared and pyrolyzed in a closed system, to observe oil expulsion or oil retention effects on later oil and gas generation from kerogen. The results show that oil expulsion and retention strongly impacts on further oil and gas generation in terms of both the amount and composition in the high maturity stage. Gas production will be reduced by 50% when the expulsion coefficient reaches 58%, and gas from oil-expelled kerogen (less oil retained) is much drier than that from fresh kerogen. The oil expulsion also causes n-alkanes and gas compounds to have heavier carbon isotopic compositions at high maturity stages. The enrichment of 13C in n-alkanes and gas hydrocarbons are 1‰ and 4–6‰ respectively, compared to fresh kerogen. Oil expulsion may act as open system opposite to the oil retention that influences the data pattern in crossplots of δ13C2–δ13C3 versus C2/C3, δ13C2–δ13C3 versus δ13C1 and δ13C1–δ13C2 versus ln(C1/C2), which are widely used for identification of gas from kerogen cracking or oil cracking. These results suggest that the reserve estimation and gas/source correlation in deep burial basins should consider the proportion of oil retention to oil expulsion the source rocks have experienced.  相似文献   

20.
《Applied Geochemistry》2005,20(11):2017-2037
The Tertiary Thrace Basin located in NW Turkey comprises 9 km of clastic-sedimentary column ranging in age from Early Eocene to Recent in age. Fifteen natural gas and 10 associated condensate samples collected from the 11 different gas fields along the NW–SE extending zone of the northern portion of the basin were evaluated on the basis of their chemical and individual C isotopic compositions. For the purpose of the study, the genesis of CH4, thermogenic C2+ gases, and associated condensates were evaluated separately.Methane appears to have 3 origins: Group-1 CH4 is bacteriogenic (Calculated δ13CC1–C = −61.48‰; Silivri Field) and found in Oligocene reservoirs and mixed with the thermogenic Group-2 CH4. They probably formed in the Upper Oligocene coal and shales deposited in a marshy-swamp environment of fluvio-deltaic settings. Group-2 (δ13CC1–C = −35.80‰; Hamitabat Field) and Group-3 (δ13C1–C = −49.10‰; Değirmenköy Field) methanes are thermogenic and share the same origin with the Group-2 and Group-3 C2+ gases. The Group-2 C2+ gases include 63% of the gas fields. They are produced from both Eocene (overwhelmingly) and Oligocene reservoirs. These gases were almost certainly generated from isotopically heavy terrestrial kerogen (δ13C = −21‰) present in the Eocene deltaic Hamitabat shales. The Group-3 C2+ gases, produced from one field, were generated from isotopically light marine kerogen (δ13C = −29‰). Lower Oligoce ne Mezardere shales deposited in pro-deltaic settings are believed to be the source of these gases.The bulk and individual n-alkane isotopic relationships between the rock extracts, gases, condensates and oils from the basin differentiated two Groups of condensates, which can be genetically linked to the Group-2 and -3 thermogenic C2+ gases. However, it is crucial to note that condensates do not necessarily correlate to their associated gases.Maturity assessments on the Group-1 and -2 thermogenic gases based on their estimated initial kerogen isotope values (δ13C = −21‰; −29‰) and on the biomarkers present in the associated condensates reveal that all the hydrocarbons including gases, condensates and oils are the products of primary cracking at the early mature st age (Req = 0.55–0.81%). It is demonstrated that the open-system source conditions required for such an early-mature hydrocarbon expulsion exist and are supported by fault systems of the basin.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号