首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献，搜索用时 296 毫秒
1.
The effect of coal moisture content and composition upon methane/carbon dioxide mixed gas adsorption characteristics is investigated. Separation factors are used to quantify the relative adsorption of carbon dioxide and methane. Experimental data indicate that carbon dioxide separation factors vary slightly between coal lithotypes, but the effects of variable coal composition and moisture upon selective adsorption are difficult to isolate. Model predictions based upon single-component isotherms show that although some variability in carbon dioxide selectivity exists for different coal types, there is no clear relationship between coal composition and carbon dioxide selectivity. Model predictions also indicate that coal moisture decreases carbon dioxide selectivity. The ideal adsorbed solution (IAS) theory and the extended Langmuir model differ substantially in their ability to predict binary gas adsorption behaviour. Comparison of model predictions to experimental data demonstrates that IAS theory, in conjunction with the Dubinin–Astakhov single-component isotherm equations are more accurate for the prediction of mixed gas desorption isotherms collected in this study than the extended Langmuir. IAS predictions, however, are strongly dependent upon the choice of pure gas isotherm equation.  相似文献   

2.
The measurement of coal porosity with different gases   总被引：1，自引：0，他引：1  
Sorption processes can be used to study different characteristics of coal properties, such as gas content (coalbed methane potential of a deposit), gas diffusion, porosity, internal surface area, etc. Coal microstructure (porosity system) is relevant for gas flow behaviour in coal and, consequently, directly influences gas recovery from the coalbed.This paper addresses the determination of coal porosity (namely micro- and macroporosity) in relation to the molecular size of different gases. Experiments entailed a sorption process, which includes the direct method of determining the “void volume” of samples using different gases (helium, nitrogen, carbon dioxide, and methane). Because gas behaviour depends on pressure and temperature conditions, it is critical, in each case, to know the gas characteristics, especially the compressibility factor.The experimental conditions of the sorption process were as follows: temperature in the bath 35 °C; sample with moisture equal to or greater than the moisture-holding capacity (MHC), particle size of sample less than 212 μm, and mass ca. 100 g.The present investigation was designed to confirm that when performing measurements of the coal void volume with helium and nitrogen, there are only small and insignificant changes in the volume determinations. Inducing great shrinkage and swelling effects in the coal molecular structure, carbon dioxide leads to “abnormal” negative values in coal void volume calculations, since the rate of sorbed and free gas is very high. In fact, when in contact with the coal structure, carbon dioxide is so strongly retained that the sorbed gas volume is much higher than the free gas volume. However, shrinkage and swelling effects in coal structure induced by carbon dioxide are fully reversible. Methane also induces shrinkage and swelling when in contact with coal molecular structure, but these effects, although smaller than those induced by carbon dioxide, are irreversible and increase the coal volume.  相似文献   

3.
This paper investigates changes in the high-volatile bituminous Lower Block Coal Member from Indiana owing to moisture availability and oxidation in air at ambient pressure and temperature over storage time. Specifically, it investigates changes in chemistry, in surface area, and pore structure, as well as changes in methane and carbon dioxide adsorption capacities. Our results document that the methane adsorption capacity increased by 40%, whereas CO2 adsorption capacity increased by 18% during a 13-month time period. These changes in adsorption are accompanied by changes in chemistry and surface area of the coal.The observed changes in adsorption capacity indicate that special care must be taken when collecting samples and preserving coals until adsorption characteristics are measured in the laboratory. High-pressure isotherms from partially dried coal samples would likely cause overestimation of gas adsorption capacities, lead to a miscalculation of coal-bed methane prospects, and provide deceptively optimistic prognoses for recovery of coal-bed methane or capture of anthropogenic CO2.  相似文献   

4.
There is still no clear understanding of the specific interactions between coal and gas molecules. In this context sorption–desorption studies of methane and carbon dioxide, both in a single gas environment and gas mixtures, are of fundamental interest. This paper presents the results of unique simultaneous measurements of sorption kinetics, volumetric strain and acoustic emission (AE) on three tetragonal coal samples subjected to sorption of carbon dioxide and methane mixtures. The coal was a high volatile bituminous C coal taken from the Budryk mine in the Upper Silesia Basin, Poland. Three different gas mixtures were used in the sorption tests, with dominant CO2, with dominant CH4 and a 50/50 mixture.The experimental set-up was designed specially for this study. It consisted of three individual units working together: (i) a unit for gas sorption experiments using a volumetric method, (ii) an AE apparatus for detecting, recording and analysing AE, and (iii) a strain meter for measuring strains induced in the coal sample by gas sorption/desorption. All measurements were computer aided.The experiments indicated that the coal tested showed preferential sorption of CH4 at 2.6 MPa pressure and exhibited comparable affinities for CH4 and CO2 at higher pressures (4.0 MPa). The results of chromatographic analysis of the gas released on desorption suggested that the desorption of methane from the coal was favoured. The relationship between the volumetric strain and the amount of sorbed gas was found to be non-linear. These results were contrary to common opinions on the coal behaviour. Furthermore, it appeared that the swelling/shrinkage of coal was clearly influenced by the network of fractures. Besides, the AE and strain characteristics suggested common sources of sorption induced AE and strain.The present results may have implications for the sequestration of carbon dioxide in coal seams and enhanced coalbed methane recovery (ECBM).  相似文献   

5.
为了研究高煤级煤储层含水性对吸附能力的影响,对阳泉-寿阳区块8件代表性煤样开展了镜质体反射率、显微组分、孔隙度、压汞、核磁共振和甲烷等温吸附等实验,分析了煤储层孔径分布、核磁共振T2谱响应特征、核磁孔隙度以及煤岩吸附能力,同时对煤储层含水性和煤储层吸附能力的相互关系进行了分析。研究结果表明：高煤级煤储层孔隙以微孔发育为主,孔隙含水性以微小孔中的束缚水赋存状态为主,且其含水量随最大镜质体反射率(Ro,m)的增大而增加。在影响高煤级煤储层吸附能力的多种因素中,煤储层含水性对煤岩吸附能力起着决定性的作用,尤其体现在微小孔中的束缚水对吸附能力的影响,束缚水含量越高,煤岩吸附能力越差。  相似文献   

6.
During the processes of methane adsorption and desorption, the internal structure of coal changes, accordingly leading to changes in electrical conductivity. In this paper, using low rank coal seams of the Yan’an Formation in the Dafosi field as the research subject, the relationship between coal resistivity, methane adsorption quantity, and equilibrium pressure is analyzed through proximate analysis, mercury injection tests, low temperature liquid nitrogen adsorption tests, and coal resistivity measurements during methane adsorption and desorption. The results show that during the process of pressure rise and methane adsorption, the conductivity of coal increases, resulting from heat release from methane adsorption, coal matrix swelling and adsorbed water molecules replaced by methane, but the resistivity reduction gradually decreases. The relationship between coal resistivity and methane adsorption quantity and equilibrium pressure can be described by a quadratic function. During the processes of depressurization and desorption, the resistivity of coal rebounds slightly, due to decalescence of methane desorption, coal matrix shrinkage and water-gas displacement, and the relationship coincides with a linear function. Methane adsorption leads to irreversible changes in coal internal structure and enhances the coal conductivity, and resistivity cannot be restored to the initial level even after methane desorption. The resistivity and reduction rate of durain are higher than those of vitrain, with relatively greater homogeneous pore throat structure and fewer charged particles in the double electric layer. In addition, moisture can enhance the conductivity of coal and makes it change more complexly during methane adsorption and desorption.  相似文献   

7.
Coal swelling/shrinkage during gas adsorption/desorption is a well-known phenomenon. For some coals the swelling/shrinkage shows strong anisotropy, with more swelling in the direction perpendicular to the bedding than that parallel to the bedding. Experimental measurements performed in this work on an Australian coal found strong anisotropic swelling behaviour in gases including nitrogen, methane and carbon dioxide, with swelling in the direction perpendicular to the bedding almost double that parallel to the bedding. It is proposed here that this anisotropy is caused by anisotropy in the coal's mechanical properties and matrix structure. The Pan and Connell coal swelling model, which applies an energy balance approach where the surface energy change caused by adsorption is equal to the elastic energy change of the coal solid, is further developed to describe the anisotropic swelling behaviour incorporating coal property and structure anisotropy. The developed anisotropic swelling model is able to accurately describe the experimental data mentioned above, with one set of parameters to describe the coal's properties and matrix structure and three gas adsorption isotherms. This developed model is also applied to describe anisotropic swelling measurements from the literature where the model was found to provide excellent agreement with the measurement. The anisotropic coal swelling model is also applied to an anisotropic permeability model to describe permeability behaviour for primary and enhanced coalbed methane recovery. It was found that the permeability calculation applying anisotropic coal swelling differs significantly to the permeability calculated using isotropic volumetric coal swelling strain. This demonstrates that for coals with strong anisotropic swelling, anisotropic swelling and permeability models should be applied to more accurately describe coal permeability behaviour for both primary and enhanced coalbed methane recovery processes.  相似文献   

8.
Small angle scattering techniques (SAXS and SANS) have been used to investigate the microstructural properties of the subbituminous coals (Rmax 0.42–0.45%) from the Huntly Coalfield, New Zealand. Samples were collected from the two thick (> 5 m) coal seams in the coalfield and have been analysed for methane and carbon dioxide sorption capacity, petrography, pore size distribution, specific surface area and porosity.Specific surface area (SSA) available for carbon dioxide adsorption, extrapolated to a probe size of 4 Å, ranged from 1.25 × 106 cm? 1 to 4.26 × 106 cm? 1 with total porosity varying from 16% to 25%. Porosity was found to be predominantly composed of microporosity, which contributed the majority of the available SSA. Although considerable variation was seen between samples, the results fit well with published rank trends.Gas holding capacity at the reservoir pressure (approximately 4 MPa) ranged from 2.63 to 4.18 m3/t for methane on a dry, ash-free basis (daf) and from 22.00 to 23.72 m3/t daf for carbon dioxide. The resulting ratio of CO2:CH4 ranged from 5.7 to 8.6, with an average of 6.7:1.Holding capacities for both methane and carbon dioxide on a dry ash free basis (daf) were found to be correlated with sample microporosity. However, holding capacities for the two gases on an as analysed (aa) basis (that is including mineral matter and moisture), showed no such correlation. Carbon dioxide (aa) does show a negative correlation with both specific surface area and microporosity. As the coals have low inorganic matter content, the reversal is thought to be related to moisture which is likely concentrated in the pore size range 12.5–125 Å. Methane holding capacity, both daf and aa, correlates with macroporosity, thus suggesting that the holding capacity of micropores is diminished by the presence of moisture in the pores.  相似文献   

9.
Laboratory experiments were conducted to investigate the adsorption kinetic behavior of pure and mixed gases (CO2, CH4, approximately equimolar CO2 + CH4 mixtures, and He) on a coal sample obtained from the Black Warrior Basin at the Littleton Mine (Twin Pine Coal Company), Jefferson County, west-central Alabama. The sample was from the Mary Lee coal zone of the Pottsville Formation (Lower Pennsylvanian). Experiments with three size fractions (45–150 µm, 1–2 mm, and 5–10 mm) of crushed coal were performed at 40 °C and 35 °C over a pressure range of 1.4–6.9 MPa to simulate coalbed methane reservoir conditions in the Black Warrior Basin and provide data relevant for enhanced coalbed methane recovery operations. The following key observations were made: (1) CO2 adsorption on both dry and water-saturated coal is much more rapid than CH4 adsorption; (2) water saturation decreases the rates of CO2 and CH4 adsorption on coal surfaces, but it appears to have minimal effects on the final magnitude of CO2 or CH4 adsorption if the coal is not previously exposed to CO2; (3) retention of adsorbed CO2 on coal surfaces is significant even with extreme pressure cycling; and (4) adsorption is significantly faster for the 45–150 μm size fraction compared to the two coarser fractions.  相似文献   

10.
A theoretical model for gas adsorption-induced coal swelling   总被引：6，自引：2，他引：6  
Swelling and shrinkage (volumetric change) of coal during adsorption and desorption of gas is a well-known phenomenon. For coalbed methane recovery and carbon sequestration in deep, unminable coal beds, adsorption-induced coal volumetric change may cause significant reservoir permeability change. In this work, a theoretical model is derived to describe adsorption-induced coal swelling at adsorption and strain equilibrium. This model applies an energy balance approach, which assumes that the surface energy change caused by adsorption is equal to the elastic energy change of the coal solid. The elastic modulus of the coal, gas adsorption isotherm, and other measurable parameters, including coal density and porosity, are required in this model. Results from the model agree well with experimental observations of swelling. It is shown that the model is able to describe the differences in swelling behaviour with respect to gas species and at very high gas pressures, where the coal swelling ratio reaches a maximum then decreases. Furthermore, this model can be used to describe mixed-gas adsorption induced-coal swelling, and can thus be applied to CO2-enhanced coalbed methane recovery.  相似文献   

11.
Geologic sequestration in deep unmineable coal seams and enhanced coalbed methane production is a promising choice, economically and environmentally, to reduce anthropogenic gases such as carbon dioxide in the atmosphere. Unmineable coal seams are typically known to adsorb large amounts of carbon dioxide in comparison to the sizeable amounts of sorbed methane, which raises the potential for large scale sequestration projects. During the process of sequestration, carbon dioxide is injected into the coalbed and desorbed methane is produced. The coal matrix is believed to shrink when a gas is desorbed and swell when a gas is sorbed, sometimes causing profound changes in the cleat porosity and permeability of the coal seam. These changes may have significant impact on the reservoir performance. Therefore, it is necessary to understand the combined influence of swelling and shrinkage, and geomechanical properties including elastic modulus, cleat porosity, and permeability of the reservoir.The present paper deals with the influence of swelling and shrinkage on the reservoir performance, and the geomechanical response of the reservoir system during the process of geologic sequestration of carbon dioxide and enhanced coalbed methane production in an actual field project located in northern New Mexico. A three-dimensional swelling and shrinkage model was developed and implemented into an existing reservoir model to understand the influence of geomechanical parameters, as well as swelling and shrinkage properties, on the reservoir performance. Numerical results obtained from the modified simulator were compared to available measured values from that site and previous studies. Results show that swelling and shrinkage, and the combination of geomechanical and operational parameters, have a significant influence on the performance of the reservoir system.  相似文献   

12.
Sequestration of carbon dioxide in unmineable coal seams is an option to reduce carbon dioxide emissions. It is well known that the interaction of carbon dioxide with unconfined coal induces swelling. This paper contributes three-dimensional strain distribution in confined coal at microstructural level using high-resolution X-ray computerized tomography data and image analysis. Swelling and compression/compaction of regions in the coal matrix occurs with CO2 uptake. Normal strain varies between ? 1.15% and 0.93%, ? 3.11% and 0.94%, ? 0.43% and 0.30% along x, y and z axes respectively. Volumetric strain varies between ? 4.25% and 1.25%. The positive strains reported are consistent with typical range for unconstrained swelling. However, the average volumetric strains value (? 0.34%) reflect overall volume reduction. Overall swelling is apparently influenced by the confining stresses. The magnitudes of normal strains are heterogeneous and anisotropic. The swelling vs. compression/compaction observed after CO2 uptake is localized and likely lithotype dependant.  相似文献   

13.
注入CO2提高煤层气产能的可行性研究   总被引：15，自引：0，他引：15  
根据煤储层吸附一解吸机理,首次采用“解吸一注气一解吸”的实验方法,分别进行CH4,CO2的吸附一解吸和CO2注入置换煤层CH4实验,模拟了煤层气井“排采一注气一排采”的增产途径和效果。结果表明：在CH4和CO2二元体系的竞争吸附中,CO2组分的吸附速率是先快后慢,而CH4组分的吸附速率先慢后快,解吸时则相反,反映出CO2在竞争吸附中占据优势;注入CO2气体的数量越大和相对浓度越高,单位压降CH4解吸率和CO2吸附率就越高。实验结论对工业规模的煤层气开发试验具有指导意义。  相似文献   

14.
The permeability of coal samples from Pittsburgh Seam was determined using carbon dioxide as the flowing fluid. The confining pressure was varied to cover a wide range of depths. The permeability was determined as a function of exposure time of carbon dioxide while the confining stress was kept constant. The porosities of the coal samples were found to be very low and most of the samples had porosities less than 1%. The permeability of these coal samples was very low—less than 1 μD. Since the objective of this study was to investigate the influence of CO2 exposure on coal permeability, it was necessary to increase the initial permeability of the coal samples by introducing a fracture. A longitudinal fracture was induced mechanically, and CT scans were taken to ensure that the fracture was present throughout the sample and that the sample was not damaged otherwise during the process. In this study, the permeability of coal was determined by using pressure transient methods. Two types of pressure pulses were used: A-spike and Sine-6 pressure transients. It was first established that the permeability of fractured coal samples did not change with exposure time when an inert gas (Argon) was used as the fluid medium in the experiments. However, the permeability of coal samples decreased significantly when carbon dioxide was used as the fluid medium. This reduction can be attributed to the coal swelling phenomenon. The results show that the permeability reduction in fractured coal samples can be over 90% of the original value, and the exposure time for such reductions can range from 1.5 days up to a week, typically about 2 days under laboratory conditions. The permeability decreased significantly with the increase in confining pressure. The higher confining pressure appears to close internal fractures causing a reduction in permeability.  相似文献   

15.
It is generally accepted that typical coalbed gases (methane and carbon dioxide) are sorbed (both adsorbed and absorbed) in the coal matrix causing it to swell and resulting in local stress and strain variations in a coalbed confined under overburden pressure. The swelling, interactions of gases within the coal matrix and the resultant changes in the permeability, sorption, gas flow mechanics in the reservoir, and stress state of the coal can impact a number of reservoir-related factors. These include effective production of coalbed methane, degasification of future mining areas by drilling horizontal and vertical degasification wells, injection of CO2 as an enhanced coalbed methane recovery technique, and concurrent CO2 sequestration. Such information can also provide an understanding of the mechanisms behind gas outbursts in underground coal mines.The spatio-temporal volumetric strains in a consolidated Pittsburgh seam coal sample were evaluated while both confining pressure and carbon dioxide (CO2) pore pressure were increased to keep a constant positive effective stress on the sample. The changes internal to the sample were evaluated by maps of density and atomic number determined by dual-energy X-ray computed tomography (X-ray CT). Early-time images, as soon as CO2 was introduced, were also used to calculate the macroporosity in the coal sample. Scanning electron microscopy (SEM) and photographic images of the polished section of the coal sample at X-ray CT image location were used to identify the microlithotypes and microstructures.The CO2 sorption-associated swelling and volumetric strains in consolidated coal under constant effective stress are heterogeneous processes depending on the lithotypes present. In the time scale of the experiment, vitrite showed the highest degree of swelling due to dissolution of CO2, while the clay (kaolinite) and inertite region was compressed in response. The volumetric strains associated with swelling and compression were between ± 15% depending on the location. Although the effective stress on the sample was constant, it varied within the sample as a result of the internal stresses created by gas sorption-related structural changes. SEM images and porosity calculations revealed that the kaolinite and inertite bearing layer was highly porous, which enabled the fastest CO2 uptake and the highest degree of compression.  相似文献   

16.
在富含水煤系或水力措施后的煤层中,受水溶液的浸泡,煤的孔隙结构及吸附特性发生改变,为了深入研究其变化规律,在实验室利用蒸馏水对2种不同变质程度煤样进行了长时间（60 d）浸泡,采用低温N2吸附实验和CO2吸附实验测试水浸前后煤样的孔隙结构变化规律,采用高压容量法测试水浸前后煤样的瓦斯吸附特性。结果表明,水浸干燥后煤体孔容和比表面积总体呈降低趋势。其中,低温N2吸附实验结果表明,煤体中大中孔的比表面积最高可降低48.9%;CO2吸附实验结果表明,水浸干燥后2种煤样的微孔孔容和比表面积也呈不同程度的降低趋势。将水浸煤样孔隙结构变化分为3个阶段,即矿物质溶出“增孔”阶段、煤基质局部膨胀变形“缩孔”阶段和煤基质整体溶胀变形“扩孔”阶段。此外,水浸干燥后煤对瓦斯的吸附能力下降,主要是由于水浸促使煤体产生膨胀变形,且导致微孔隙相互连通,从而降低了煤体微孔孔容和比表面积,降低瓦斯吸附能力。研究成果对进一步掌握富含水煤系或水力化措施后煤层的瓦斯抽采具有指导意义。   相似文献   

17.
Enhanced coalbed methane (ECBM) involves the injection of a gas, such as nitrogen or carbon dioxide, into the coal reservoir to displace the methane present. Potentially this strategy can offer greater recovery of the coal seam methane and higher rates of recovery due to pressure maintenance of the reservoir. While reservoir simulation forms an important part of the planning and assessment of ECBM, a key question is the accuracy of existing approaches to characterising and representing the gas migration process. Laboratory core flooding allows the gas displacement process to be investigated on intact coal core samples under conditions analogous to those in the reservoir. In this paper a series of enhanced drainage core floods are presented and history matched using an established coal seam gas reservoir simulator, SIMED II. The core floods were performed at two pore pressures, 2 MPa and 10 MPa, and involve either nitrogen or flue gas (90% nitrogen and 10% CO2) flooding of core samples initially saturated with methane. At the end of the nitrogen floods the core flood was reversed by flooding with methane to investigate the potential for hysteresis in the gas displacement process. Prior to the core flooding an independent characterisation programme was performed on the core sample where the adsorption isotherm, swelling with gas adsorption, cleat compressibility and geomechanical properties were measured. This information was used in the history matching of the core floods; the properties adjusted in the history matching were related to the affect of sorption strain on coal permeability and the transfer of gas between cleat and matrix. Excellent agreement was obtained between simulated and observed gas rates, breakthrough times and total mass balances for the nitrogen/methane floods. It was found that a triple porosity model improved the agreement with observed gas migration over the standard dual porosity Warren-Root model. The Connell, Lu and Pan hydrostatic permeability model was used in the simulations and improved history match results by representing the contrast between pore and bulk sorption strains for the 10 MPa cases but this effect was not apparent for the 2 MPa cases. There were significant differences between the simulations and observations for CO2 flow rates and mass balances for the flue gas core floods. A possible explanation for these results could be that there may be inaccuracy in the representation of mixed gas adsorption using the extended Langmuir adsorption model.  相似文献   

18.
Studying gas transport mechanisms in coal seams is crucial in determining the suitability of coal formations for geosequestration and/or CO2-enhanced coal bed methane recovery (ECBM), estimating CO2 storage capacity and recoverable volume of methane, and predicting the long-term integrity of CO2 storage and possible leakages. Due to the dual porosity nature of coal, CO2 transport is a combination of viscous flow and Fickian diffusion. Moreover, CO2 is adsorbed by the coal which leads to coal swelling which can change the porous structure of coal and consequently affects the gas flow properties of coal, i.e. its permeability. In addition, during CO2 permeation, the coal seam undergoes a change in effective stress due to the pore pressure alteration and this can also change the permeability of the coal seam. In addition, depending on the in situ conditions of the coal seam and the plan of the injection scheme, carbon dioxide can be in a supercritical condition which increases the complexity of the problem. We provide an overview of the recent studies on porous structure of coal, CO2 adsorption onto coal, mechanisms of CO2 transport in coalbeds and their measurement, and hydro-mechanical response of coal to CO2 injection and identify opportunities for future research.  相似文献   

19.
We report laboratory experiments that investigate the permeability evolution of an anthracite coal as a function of applied stress and pore pressure at room temperature as an analog to other coal types. Experiments are conducted on 2.5 cm diameter, 2.5-5 cm long cylindrical samples at confining stresses of 6 to 12 MPa. Permeability and sorption characteristics are measured by pulse transient methods, together with axial and volumetric strains for both inert (helium (He)) and strongly adsorbing (methane (CH4) and carbon dioxide (CO2)) gases. To explore the interaction of swelling and fracture geometry we measure the evolution of mechanical and transport characteristics for three separate geometries — sample A containing multiple small embedded fractures, sample B containing a single longitudinal through-going fracture and sample C containing a single radial through-going fracture. Experiments are conducted at constant total stress and with varied pore pressure — increases in pore pressure represent concomitant (but not necessarily equivalent) decreases in effective stress. For the samples with embedded fractures (A and C) the permeability first decreases with an increase in pressure (due to swelling and fracture constraint) and then increases near-linearly (due to the over-riding influence of effective stresses). Conversely, this turnaround in permeability from decreasing to increasing with increasing pore pressure is absent in the discretely fractured sample (B) — the influence of the constraint of the connecting fracture bridges in limiting fracture deformation is importantly absent as supported by theoretical considerations. Under water saturated conditions, the initial permeabilities to all gases are nearly two orders of magnitude lower than for dry coal and permeabilities increase with increasing pore pressure for all samples and at all gas pressures. We also find that the sorption capacities and swelling strains are significantly reduced for water saturated samples — maybe identifying the lack of swelling as the primary reason for the lack of permeability decrease. Finally, we report the weakening effects of gas sorption on the strength of coal samples by loading the cores to failure. Results surprisingly show that the strength of the intact coal (sample A) is smaller than that of the axially fractured coal (sample B) due to the extended duration of exposure to CH4 and CO2. Average post-failure particle size for the weakest intact sample (A) is found to be three times larger than that of the sample B, based on the sieve analyses from the samples after failure. We observe that fracture network geometry and saturation state exert important influences on the permeability evolution and strength of coal under in situ conditions.  相似文献   

20.
页岩中气体的超临界等温吸附研究   总被引：1，自引：0，他引：1  
页岩气等温吸附实验多为临界温度以上的吸附实验,其得到的吸附量为过剩吸附量。为了研究页岩气超临界等温吸附机理,运用重力法,在临界温度以上,分别进行了甲烷和二氧化碳在页岩中的高压等温吸附实验。在分析经典型吸附和超临界吸附区别的基础上,通过修改的超临界等温吸附模型(Langmuir方程和微孔充填(Dubinin Radushkevich,D-R))对实验数据进行了拟合。结果表明:简单的Langmuir方程可近似拟合甲烷吸附实验数据,但精度不高,且无法拟合二氧化碳的吸附数据;将吸附相密度作为可优化参数,修改的微孔充填模型和Langmuir模型能很好地拟合甲烷和二氧化碳的吸附数据,其中修改的微孔充填模型拟合效果最好,且回归得到的超临界甲烷吸附相密度同文献报道的一致,表明吸附气可能以微孔充填的形式存在。   相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号