共查询到20条相似文献，搜索用时 421 毫秒
1.
It is universally known that residual soils behave very differently from sedimentary soils. While the latter is widely known as cross-anisotropic, little is known regarding the strength anisotropy of residual soils. This study presents how the inherent anisotropy affects the strength of natural granite residual soils under generalized conditions, where intact specimens were carefully prepared and sheared under triaxial compression, extension, simple shear, and hollow cylinder torsional shear tests. The strength of natural residual soil, in terms of ultimate stress ratio M and undrained shear strength Su, is found to be significantly anisotropic in a different way from normally consolidated clays with the maximum strength obtained under triaxial compression and the minimum under simple shear or at intermediate principal stress direction. As a result, the existing method failed to measure the anisotropy degree of the studied soil. Two parameters were proposed accordingly to quantify the anisotropic strength under general conditions, taking the special strength anisotropy pattern and cohesive-frictional nature of GRS into account. The proposed parameters enable the direct comparison of strength anisotropy among soils. This study serves as a data set to better understand residual soils regarding their anisotropic behaviors under generalized conditions. Although specific to granite residual soils in China, this study is expected to be more widely applicable to other weathered geomaterials. 相似文献
2.
This paper describes the main findings of a laboratory study on the mechanical behaviour of cemented geologically normally
consolidated lacustrine clayey soils from two sites, Bacinetto (BA) and Avezzano (AZ), in the Fucino basin (Italy). One-dimensional
and triaxial compression tests were carried out in order to investigate the effects of the presence and of the progressive
degradation of the interparticle cementation bonds. The two tested soils showed quite different physical and mechanical properties,
the more apparent ones being plasticity and yield stress values. The experimental results allowed the gross yield curves and the critical state conditions to be identified for both soils (BA clay and AZ silt). A number of typical
features generally exhibited by cemented soils were clearly apparent: yield stresses greater than the in situ stress states,
both soils being geologically normally consolidated; high values of compressibility index after yielding, which gradually
reduce with increasingly applied stresses; strength reductions associated with a globally contractive behaviour. A convenient
normalisation of the experimental results, in which the critical state conditions are assumed as a reference state, allowed
the effects of cementation bonds and of their progressive degradation to be highlighted. In particular, BA samples were found
to be characterised by different structures related to different degrees of cementation. Furthermore, despite the larger values of the yielding stresses exhibited by AZ silt, stronger effects of
cementation are apparent in BA soil. Experimental results seem to indicate that at high values of the applied stress and strain
paths, when bonds are largely damaged, the structures of the natural and parent reconstituted BA soil continue to be different. 相似文献
3.
Existing models for predicting the small strain behaviour of unsaturated soil are not capable of predicting the initial shear stiffness during suction reduction under normally consolidated conditions. This problem has been addressed in the present study by combining an existing elastoplastic model and recent experimental data to provide a new model for the initial shear stiffness. The model, which is similar to that typically adopted for saturated soils, uses the average skeleton stress and an additional function of the degree of saturation. This new model not only captures the behaviour of the new experimental results, but it also describes a unique relationship between saturated and unsaturated soils. 相似文献
4.
通过对粘性土进行一系列动三轴试验，测定并分析了动荷载作用下为粘性土的动剪应力，轴向应变及超孔隙水压力随时间的变化规律，分析了破坏时不同固结比的粘性土对静，动剪强度和孔隙水压力影响规律，得出了粘性土的动剪强度随固结比变化的关系式，并对粘性土的动剪强度判别方法的标准进行探讨，得出了有益的结果。 相似文献
5.
Clayey soils in the vicinity of energy geostructures may be exposed to long-term periodic thermal cycles. The creep and consolidation behaviors of the clayey soils can be both rate-dependent and temperature-dependent, and the underlying physical mechanisms are merely investigated theoretically. In this study, based on the theory of thermodynamics, a fully coupled thermo-hydro-mechanical (THM) finite element (FE) program for saturated soils is developed for this purpose. The FE formulation accounts for the combined effect of rate and temperature through the novel concept of granular temperature. Simulations of THM coupled validation cases and a series of experimental observations on the soft Bangkok clay are carried out. The obtained numerical results exhibit good agreement with analytical solutions and laboratory measurements. It is found that three fundamental physical mechanisms contribute to the irreversible thermal contraction observed for normally consolidated and lightly overconsolidated clays under drained thermal cycles: (1) the thermal creep excited by mass exchange from adsorbed water to free water; (2) the mechanical creep induced by confining stresses; and (3) the increase in granular packing caused by the thermal expansion of soil particles. The thermal contraction generally stabilizes within a few thermal cycles, as a result of the noticeable reduction in the thermal creep rate. It is further demonstrated that the transient heat transfer and the heating rate can greatly influence the deformation of clays subjected to thermal cycles. 相似文献
6.
基于上海地区19个工程共201组数据,通过黏土、粉质黏土和粉砂在上海地区土层中的分布,比贯入阻力Ps,室内固结快剪试验黏聚力cu和摩擦角?u,孔隙比e,塑性指数Ip沿土层深度的变化,分析得到3种土类的抗剪强度与比贯入阻力的相关关系,并总结了国内软土地区土体抗剪强度与静力触探比贯入阻力之间的相关关系。本文得到黏土的相关关系与以往的经验公式相近,同时给出了原位土层粉质黏土和粉砂的相关关系。区别不同土类使得相关关系可用性提高,在工程应用中更加合理。根据本文相关关系,通过静力触探比贯入阻力可以得到不同土层的抗剪强度值,进而应用于基坑稳定计算。本文研究的结果可以应用于海相沉积土的勘察和工程设计工作。 相似文献
7.
For the last 40 years, the CPT has played a key role in offshore soil investigations, mainly in connection with oil and gas development, but also for other purposes. The offshore application of CPT has been an important factor with regards to development of equipment, data processing and interpretation. Each of the following aspects are discussed in terms of historic development, present status and future challenges: - Deployment method and equipment. - Penetrometer design and construction. - Data acquisition, processing and quality control. - Standards and guidelines. - Interpretation of results and application in foundation design. It is shown that these developments have greatly enhanced the reliability and applicability of the use of the CPT in soil investigations and design. However, there are still important challenges to be faced in the future 相似文献
8.
天然沉积的软土普遍具有结构性,常规计算软土次固结变形的方法并没有反映结构性的影响。通过对漳州与青岛地区原状软土与重塑土进行次固结试验,研究软土结构性对次固结系数 的影响。结果表明,软土的 随压力 增大而增大,在 接近结构屈服压力 时达到最大值,此后逐渐减小,受 影响减弱,最后与重塑土的 趋于一致;重塑土的 受压力影响很小,可视为常数。根据次固结系数与压缩指数比值 确定 可能存在一定误差。由于结构性的影响,正常固结软土表现出“假超固结”现象,采用超固结角度对结构性软土 变化规律进行说明并不合适,而根据不同压力下软土结构破损的情况可以很好解释这一现象。 相似文献
9.
Piles are structural members made of steel, concrete, or wood installed into the ground to transfer superstructure loads to the soil. Nowadays, many structures are built on poor lands, and therefore piles have crucial roles in such structures. Performing in-situ tests such as cone penetration (CPT) and piezocone penetration tests (CPTu) have always been of great importance in designing piles. These tests have a brilliant consistency with reality, and as a result, the outcome data can be used in order to achieve reliable pile designing models and reduce uncertainty in this regard. In this paper, the capability of various CPT and CPTu based methods developed from 1961 to 2016 has been investigated using four statistical methods. Such CPT and CPTu based methods are adopted for direct prediction of axial bearing capacity of piles using CPT and CPTu field data. For this purpose, 61 sets of field data prepared from CPT and CPTu have been collected. The data sets were utilized in order to calculate the axial bearing capacity of piles (QE) through 25 different methods. In addition, the measured axial pile capacities (QM) have been collected, recorded and prepared from field static load tests, respectively. Then, four different statistical approaches have been applied to assess the accuracy of these methods. Finally, the most reliable and accurate methods are presented. 相似文献
10.
The vertical bearing capacity of spudcan foundations in strength anisotropic soils is investigated numerically using the MIT-S1 model implemented in the AFENA finite element package. The model in AFENA is validated against existing laboratory test data of normally consolidated soil. The bearing capacities of spudcans in soils with isotropic and anisotropic strengths are compared. Soil with isotropic strength is simulated using an elasto-plastic model. It is found that the bearing capacity of a spudcan in an anisotropic soil is reduced by about 9% for a rough spudcan and 3% for a smooth spudcan on average. There is a combined effect of soil anisotropy and spudcan roughness on the spudcan bearing capacity. Moreover, the effect of the pressuremeter strength of an anisotropic soil on foundation capacity can’t be ignored. 相似文献
11.
通过对动力固结法加固的某软土路堤软土内的孔隙水压力增长与消散、软土的分层沉降、路堤的表层沉降和软土的深层水平位移的监测结果及静力触探和十字板剪切试验对地基加固效果的检测结果的分析说明,在一定的条件下,对某些淤泥及淤泥质土等软土路基采用该方法进行处理是可行的,并对其使用范围进行了说明。 相似文献
12.
软土的次固结对于软土的变形量非常重要。在软土次固结计算中,通常以次固结系数作为计算参数,但该系数不能反映荷载变化的影响,而且只适用于正常固结土。由于工程中所遇到的大都为超固结土,对超固结土的次固结计算还缺少合理的方法。通过室内试验开展了软土次固结沉降相关研究,进行了多组原状软土试样的分级加载次固结试验,试验结果表明,对于软土次固结计算,建议从次固结应变与时间关系的角度,采用双曲线形式进行拟合,并分别对正常固结和超固结状态的次固结应变参数进行分析,建立了一维次固结的经验模型公式,提出了一种考虑压力对次压缩影响的次固结沉降计算方法,并将该方法应用于现场工程项目,验证了该方法可以适用于正常固结土和超固结土,使得软土次固结沉降量的计算能够更好地反映实际工程问题。 相似文献
13.
Four sinkholes with varying surficial expressions were subjected to detailed stratigraphic and soil analysis by means of Standard
Penetration Tests (SPT) and Electric Friction Cone Penetration Tests (CPT) in order to evaluate applications of CPT to sinkhole
investigations. Although widely used, SPT data are of limited value and difficult to apply to sinkhole mapping. CPT is sensitive
to minor lithologic variability and is superior to SPT as a cost-effective technique for determining geotechnical properties
of sinkholes.
The effectiveness of CPT data results from the force measurements made along the sleeve of the cone. The friction ratio (ratio
of sleeve to tip resistance) is a good indicator of soil stratigraphy and properties. By smoothing the friction-ratio data,
general stratigraphy and changes in soil properties are easily identified.
Stratigraphy of the sinks has been complicated by intense weathering, karstification and marine, transgressions. The resulting
deposits include five stratigraphic units. I and II represent Plio-Pleistocene marine sediments with Unit II being the zone
of soil clay accumulation. III and IV are horizons residual from Miocene strata and indicate an episode of karstification
prior to deposition of Units I and II.
Conduit fill is a mixture of materials with low cohesion. The fill materials indicate centripetal and downward movement of
insoluble sediments derived from the surrounding strata. Loss of cohesion results in near-zero friction ratios. Very low friction
ratios, coupled with materials with little cohesion, indicate potentially-liquefiable soils in the immediate vicinity of zones
where piping failure may be imminent. SPT does not provide sufficient data to predict these zones of potential, failure.
CPT provides sufficient information for recognition of sinkhole stratigraphy and geotechnical properties. When coupled with
laboratory soil analysis, CPT provides unique information about sinkhole geometry and dynamics. In contrast, SPT data fail
to produce consistent indicators of sinkhole stratigraphy or properties. With laboratory soil data, SPT indicates general,
inconclusive trends. 相似文献
14.
通过对11项典型工程场地进行原位取土及双桥静力触探原位测试分析,重点研究了上海地区薄层粘性土（或粘质粉土）夹层对液化判别的影响,统计分析了锥尖阻力qc、摩阻比Rf与土层粘粒含量的相关关系,提出了完全依据双桥静力触探试验的地基液化判别方法,在工程应用中取得了显著经济效益。 相似文献
15.
对不同地区软土经水泥加固后的强度形成特征进行了研究。进行直接剪切试验及无侧限抗压试验测定了水泥加固土的力学指标,发现不同地区的软土经水泥加固后力学性质存在很大差异,从试样的粒度成分、有机质含量及加固后试样的微观结构特征等方面对此进行解释。结果表明,试样的粒度成分及有机质含量会对加固效果产生很大影响,黏粒含量越大,有机质含量越高,对水泥加固土强度的形成越不利。为在用水泥进行不同性质的软土加固处理时采取合理的附加措施提供了理论依据。 相似文献
16.
为了分析一般意义的非线性固结过程中超静孔压的发展规律,基于欧拉描述的基本方程和构形转换关系,提出了非线性固结过程中超静孔压与孔隙比之间的严格函数表达式。在Morris提出的线性有限应变一维固结解析解答基础上,得到双面排水情况下正常固结和自重固结土体的超静孔压解析解。分析和讨论了超静孔压的非对称分布特征及其影响因素。结果表明,无量纲参数N在超静孔压分布形态上起决定作用。在N不接近于0的情况下,按经典Terzaghi固结理论的超静孔压对称性分布假设将不再适用于非线性固结问题。 相似文献
17.
ABSTRACTThe main sources of uncertainty in the soil specification and mechanical behaviour consist of the lithological and heterogeneous randomness of soil deposits. It is quite obvious that the cone penetration testing (CPT) data and the variation of soil characteristics are not stationary. Hence, this paper investigates a new approach to realise a CPT data, taking both sources of uncertainty into consideration. In this regard, the first part of this study illustrates a simple approach to stratify the CPT data, using the Eslami–Fellenius chart of classification. In the second part, the non-stationary algorithm of generating random field is introduced to generate a multi-layer random field. This algorithm takes account of each layer’s statistical properties (i.e. standard deviation, mean, and the trend value), separately. To validate the proposed approach, 41 case histories from different worldwide sites, have been regenerated by considering both the stationary and non-stationary algorithms. The correlation coefficient between real and realised CPT data has been employed to show that the proposed non-stationary algorithm can simulate the CPT data more accurately in comparison with the stationary algorithm. 相似文献
18.
以京沪高铁深厚地层细粒土固结试验数据为基础,以e-lgp曲线包含分式函数的复合函数表达和土体液限与压缩指数的线性关系为依据,提出了基于土体基本物性指标标准压缩模量E1?2和液限wL推求正常固结原状地基土全压力段压缩模量的简化方法,其适用性得到了京津城际铁路试验数据的验证。结果表明,Harris函数能较好地描述土体压缩的e-lgp曲线特征,E1?2和wL能分别反映曲线低压力段割线斜率和高压力点切线斜率,建立的地基土压缩模量估算方法具有良好精度,其中,100～1 000 kPa常压力段的误差均值仅为7.89%,高压力段约为13.70%,只在低压力段变异性较大;研究成果提供了缺少e-lgp曲线情况下简便快速获取土体压缩模量的新途径。 相似文献
19.
A shortcoming of the hypoplastic model for clays proposed by the first author is an incorrect prediction of the initial portion
of the undrained stress path, particularly for tests on normally consolidated soils at isotropic stress states. A conceptually
simple modification of this model, which overcomes this drawback, is proposed in the contribution. The modified model is applicable
to both normally consolidated and overconsolidated soils and predicts the same swept-out-memory states (i.e., normal compression
lines) as the original model. At anisotropic stress states and at higher overconsolidation ratios the modified model yields
predictions similar to the original model. 相似文献
20.
基于试验基础上建立的经典弹塑性模型--剑桥模型能够准确描述正常固结土的应力-应变关系。当土体的应力历史上经历过卸载或受到循环交变荷载作用即进入超固结状态,它作为土的应力历史的反映,相比正常固结土受力特性有着显著的差异。为研究超固结因素对土体加载特性的影响,在引入能考虑超固结状态影响的下负荷面剑桥模型后,通过三轴压缩和剪切试验对处于超固结状态下土体的受力特性进行了对比分析,并对循环剪切加载下的应力-应变关系以及超固结比的演化规律进行了研究。结果表明,下负荷面剑桥模型能准确反映超固结因素对土体力学特性的影响,相比原状土有着更高的屈服强度。而通过数值模拟自由场地基在地震作用下的动力响应可以看出,超固结因素对地基的动力响应起到了不可忽略的影响,尤其在强震下更需要考虑其影响。在自由场地基地震动力响应基础上,通过对桩柱结构桩-土耦合系统在地震作用下非线性动力响应的模拟对土体非线性以及超固结因素的影响进行了对比研究,研究表明：土体的非线性因素能显著降低结构振动响应中的高频成分,由于土体在交变加载下很快进入超固结状态,相对于剑桥模型,下负荷面剑桥模型在考虑超固结因素后土体的承载性能显著提高,尤其在强震作用下超固结因素带来的影响更加明显,因此,建议对桩基结构物地震响应研究考虑超固结因素影响,以提高桩基结构物地震响应模拟的精确度和可靠性。 相似文献
|
