首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献，搜索用时 15 毫秒
1.
This paper focuses on the effective utilization of pond ash, as foundation medium. A series of laboratory model tests have been carried out using square, rectangular and strip footings on pond ash. The effects of dry density, degree of saturation of pond ash, size and shape of footing on ultimate bearing capacity of shallow foundations are presented in this paper. Local shear failure of a square footing on pond ash at 37% moisture content (optimum moisture content) is observed up to the values of dry density 11.20 kN/m3 and general shear failure takes place at the values of dry density 11.48 kN/m3 and 11.70 kN/m3. Effects of degree of saturation on ultimate bearing capacity were studied. Experimental results show that degree of saturation significantly affects the ultimate bearing capacity of strip footing. The effect of footing length to width ratio (L/B), on increase in ultimate bearing capacity of pond ash, is insignificant for L/B ≥ 10 in case of rectangular footings. The effects of size of footing on ultimate bearing capacity for all shapes of footings viz., square, rectangular and strip footings are highlighted.  相似文献   

2.
Ma  Shuqi  Gutierrez  Marte 《Acta Geotechnica》2021,16(2):581-594

Shales play important roles in various civil, energy and environmental engineering applications. Shales are categorized as poroelastic materials due to their tight and very stiff structure, and reliable poroelastic properties are required when dealing with shales. This paper presents simple procedures to determine the poroelastic properties of rocks using oedometer and triaxial consolidation tests. The procedures, which avoid the difficulty to perform determination of the unjacketed bulk modulus of the rock minerals, are demonstrated on a North Sea shale. The experimentally obtained Biot coefficient α and the drained bulk modulus K of the shale range from 0.95 to 0.99, and from 0.17 to 2.00 GPa, respectively. The Biot coefficient α and the drained bulk modulus K values determined from the oedometer and triaxial tests are compared and show good agreement and consistency between the two test procedures. The Skempton’s coefficient B-value of the triaxial samples was also experimentally measured prior to the triaxial consolidation tests. The theoretically predicted B-value varies from 0.81 to 0.96 which is, on the average, only about 10% higher than the experimentally obtained B-value which range from 0.80 to 0.85.

  相似文献   

3.
The method of stress characteristics has been used for computing the ultimate bearing capacity of strip and circular footings placed on rock mass. The modified Hoek‐and‐Brown failure criterion has been used. Both smooth and rough footing‐rock interfaces have been modeled. The bearing capacity has been expressed in terms of nondimensional factors Nσ0 and Nσ, corresponding to rock mass with (1) γ = 0 and (2) γ ≠ 0, respectively. The numerical results have been presented as a function of different input parameters needed to define the Hoek‐and‐Brown criterion. Slip line patterns and the pressure distribution along the footing base have also been examined. The results are found to compare generally well with the reported solutions.  相似文献   

4.
The ultimate bearing capacity of a new strip footing placed on a cohesionless soil medium, in the presence of an existing strip footing, the load on which is assumed to be known, has been determined. Both the footings are assumed to be perfectly rigid and rough. The analysis is carried out by using an upper bound finite element limit analysis. For different clear spacing (S) between the footings, the values of the efficiency factor (ξγ) were determined; where ξγ is defined as the ratio of the failure load for an interfering new footing of a given width (B) to that for a single isolated footing having the same width. For ϕ < 30°, it is generally noted that the magnitude of ξγ increases continuously with a decrease in S/B. For ϕ > 30°, on the other hand if the applied load on the existing footing is approximately greater than half the failure load for a single isolated footing having the same width, the peak magnitude of ξγ was found to occur at around S/B ≈ 0.1 rather than at S/B = 0. The increase in ξγ becomes further significant with an increase in the magnitude of the load on the existing footing.  相似文献   

5.
In recent times, rapid urbanisation coupled with scarcity of land forces several structures to come up ever closer to each other, which may sometime cause severe damage to the structures from both strength and serviceability point of view, and therefore, a need is felt to devise simplified methods to capture the effect of footing interference. In the present study, an attempt has been made to model the settlement behaviour of two strip footings placed in close spacing on layered soil deposit consisting of a strong top layer underlying a weak bottom layer. Theory of elasticity is employed to derive the governing differential equations and subsequently solved by the finite difference method. The perfectly rough strip footings are considered to be resting on the surface of two-layer soil system, and the soil is assumed to behave as linear elastic material under a range of static foundation load. The effect of various parameters such as the elastic moduli and thickness of two layers, clear spacing between the footings and footing load on the settlement behaviour of closely spaced footings has been determined. The variation of vertical normal stress at the interface of two different soil layers as well as at the base of the failure domain also forms an important part of this study. The results are presented in terms of settlement ratio (ξδ), and their variation is obtained with the change in clear spacing between two footings. The present theoretical investigation indicates that the settlement of closely spaced footings is found to be higher than that of single isolated footing, which further reduces with increase in the spacing between the footings.  相似文献   

6.
Stress-path dependent behavior of a weathered clay crust   总被引：1，自引：0，他引：1  
Triaxial compression and oedometer consolidation tests are commonly performed to evaluate the strength and deformation behavior of soils. However, in the field, the stress paths imposed by various engineering works may deviate from the stress paths conventionally used in laboratory tests. Moreover, the stress-paths followed by different soil elements under a foundation are different. To obtain representative soil parameters, the laboratory stress path should be similar to that followed in the field. In this study, a significant number of stress-path triaxial tests, with stress probes in various directions, have been conducted to study the stress-path dependent behavior of an overconsolidated weathered crust of Champlain clay in Eastern Ontario. Both undrained and drained tests have been conducted for samples isotropically consolidated to the in situ vertical stress and anisotropically consolidated to in situ state of stress. The yield locus of the clay crust has been defined. It has been observed that the strength-deformation and yielding behavior of this weathered clay crust highly depends on the stress-path as well as on the in situ stress history.  相似文献   

7.
Footing settlements depend not only on physical and mechanical properties of base soils, but also on applied load intensities and their distributions with depth, as well as on footing rigidity, shape and dimensions. An analytical expression relating rigid bearing plate and/or footing settlements to thicknesses of deformation (active) zones, which form below footing bottoms, has been previously offered by the author. The results of tests performed with 0.5, 1.0 and 4.0 m2-area square footings, constructed on undisturbed clayey soils and containing data describing active zone development, were collected from literature and analyzed. This paper presents graphical relationships between square footing settlements, active zone thicknesses and footing dimensions, which are verified by published test results performed with experimental square footings, having areas different than the ones selected for statistical analyses.  相似文献   

8.
The influence of a non-coaxial model for granular soils on shallow foundation analyses is investigated. The non-coaxial plasticity theory proposed by Rudnicki and Rice (J. Mech. Phys. Solids 1975, 23, 371–394) is integrated into a Drucker–Prager model with both perfect plasticity and strain hardening. This non-coaxial model is numerically implemented into the finite-element program ABAQUS using a substepping scheme with automatic error control. The influence of the non-coaxial model on footing settlement and bearing capacity is investigated under various loading and boundary conditions. Compared with the predictions using conventional coaxial models, the non-coaxial prediction results indicate that the settlement of a footing increases significantly when the non-coaxial component of plastic strain rate is taken into consideration, although ultimate footing bearing capacities are not affected significantly. The non-coaxial model has a different effect on footing settlements under different loading and boundary conditions. In general, the discrepancies between coaxial and non-coaxial predictions increase with increasing rotation of principal stresses of the soil mass beneath a footing. It can be concluded that if the non-coaxial component of plastic strain rate is neglected in shallow foundation problems using the finite-element method, the results tend to be non-conservative when designs are dominated by settlement of footings.  相似文献   

9.
The ultimate bearing capacity of a group of equally spaced multiple rough strip footings was determined due to the contribution of soil unit weight. The analysis was performed by using an upper bound theorem of limit analysis in combination with finite elements and linear programming. Along the interfaces of all the triangular elements, velocity discontinuities were considered. The value of ξγ was found to increase continuously with a decrease in S/B, where (i) ξγ is the ratio of the failure load of an interfering strip footing of a given width (B) to that of a single isolated strip footing having the same width and (ii) S is the clear spacing between any two adjacent footings. The effect of the variation of spacing on ξγ was found to be very extensive for small values of S/B; ξγ approaches infinity at S/B=0. In all the cases, the velocity discontinuities were found to exist generally in a zone only around the footing edge. Copyright © 2008 John Wiley & Sons, Ltd.  相似文献   

10.
ASTM Standards instruct experimenters to use circular or square bearing plates/footings having areas ranging between 0.073 and 0.456 m2. In general, researchers and contractors perform loading bearing plate/footing tests using plates/footings which have dimensions exceeding the ones recommended by the Standards. This paper offers formulas describing relationships between settlements of square and circular plates/footings having areas ranging between 0.5 and 4.0 m2 and deformation zones developing beneath them. The proposed formulas are verified by the results of field tests performed with circular and square plates or footings supported by cohesive soils.  相似文献   

11.
By using an upper bound limit analysis in conjunction with finite elements and linear programming, the ultimate bearing capacity of two interfering rough strip footings, resting on a cohesionless medium, was computed. Along all the interfaces of the chosen triangular elements, velocity discontinuities were employed. The plastic strains were incorporated using an associated flow rule. For different clear spacing (S) between the two footings, the efficiency factor (ξγ) was determined, where ξγ is defined as the ratio of the failure load for a strip footing of given width in the presence of the other footing to that of a single isolated strip footing having the same width. The value of ξγ at S/B = 0 becomes equal to 2.0, and the maximum ξγ occurs at S/B = Scr/B. For S/B?Scr/B, the ultimate failure load for a footing becomes almost half that of an isolated footing having width (2B + S), and the soil mass below and in between the two footings deforms mainly in the downward direction. In contrast, for S/B>Scr/B, ground heave was noticed along both the sides of the footing. As compared to the available theories, the analysis provides generally lower values of ξγ for S/B>Scr/B. Copyright © 2007 John Wiley & Sons, Ltd.  相似文献   

12.
The pressure versus settlement response is highly non-linear for soils, in general. In the present study, a cubic equation of the type p = K1w ? K2w3 is suggested to incorporate the non-linear behaviour. A trapezoidal footing with constant depth resting on a subgrade having non-linear response is analysed. The resulting fourth order non-linear differential equation with variable coefficients is solved by using the Galerkin technique and beam characteristic functions are employed to obtain faster convergence. The results are presented in the form of non-dimensional charts for valid ranges of footings and soil parameters.  相似文献   

13.
This paper presents a design approach for strip footings upon glacier ice. Safety against ultimate limit state is proved by the geotechnical slip-line field solution by Prandtl. Glacier ice at 0°C can be modelled as purely cohesive material. Statistical evaluation of uniaxial compression tests with high strain rate revealed a mean value of the cohesion of 600 kPa and a characteristic value c k = 355 kPa (5% fractile). With a coefficient of variation V c = 0.3, the partial safety factor turns out to be γ c = 1.9. An approximate solution for estimating the creep settlement rate is presented to check the serviceability limit state: with the width b of the strip foundation, p the foundation pressure and for ice at 0°C. Experiences on Stubai glacier with grate shaped footings showed that creep settlements occurring per year due to maximum foundation pressures 250 kPa did not influence the operation and the maintenance of the cable cars.  相似文献   

14.
非均质地基承载力及破坏模式的FLAC数值分析   总被引：3，自引：0，他引：3  
利用基于Lagrangian显式差分的FLAC算法，通过数值计算，对黏结力随深度线性增长的非均质地基上条形基础和圆形基础的极限承载力及地基破坏模式进行了对比计算与系统分析。研究表明：（1）随着地基黏结力沿深度非均匀变化系数的增大，地基的破坏范围逐渐集中在地基表层和基础两侧：（2）即使地基的非均质程度较小，当将非均质地基近似地按均质地基考虑时，由此所估算的承载力可能过于保守；（3）地基承载力系数随黏结力沿深度非均匀变化系数的增大而非线性地增大。与数值解相比，skempton与Peck等近似公式均可能高估了非均质地基承载力。  相似文献   

15.
The ultimate bearing capacity of two closely spaced strip footings, placed on a cohesionless medium and loaded simultaneously to failure at the same magnitude of failure load, was determined by using an upper bound limit analysis. A logarithmic spiral radial shear zone, comprising of a number of triangular rigid blocks, was assumed to exist around each footing edge. The equations of the logarithmic spiral arcs were based on angles φL and φR rather than soil friction angle φ; the values of φL and φR were gradually varied in between 0 and φ. The ultimate bearing capacity was found to become maximum corresponding to a certain critical spacing between the footings. For spacing greater than the critical, the bearing capacity was found to decrease continuously with increase in the spacing. The extent of the spacing corresponding to which the ultimate bearing capacity becomes either maximum or equal to that of a single isolated footing increases with increase in φ. The results compare reasonably well with the available theoretical and experimental data.  相似文献   

16.
In order to investigate the strength and deformation anisotropy of compacted decomposed granite soils, a series of drained triaxial compression tests was performed on unsaturated and saturated decomposed granite soils. The specimens were subjected to compression tests such that the angle δ of the direction of the major principal stress, σ 1, during triaxial compression relative to the compaction plane (bedding plane) varies, with δ = 0°, 45° and 90°. Test results indicated that the compressive strain of the specimens subjected to isotropic consolidation was influenced strongly by the angle δ. In addition, the effect of the angle δ on the triaxial compressive strength and deformation was more evident in unsaturated specimens than in saturated specimens. Based on the test results, a procedure which can be used to estimate the shear strength of unsaturated soils taking into account various angles δ was proposed.  相似文献   

17.
The elastic moduli of magnesioferrite spinel, MgFe2O4, and their temperature dependence have been determined for the first time by ultrasonic measurements on a polycrystalline specimen. The measurements were carried out at 300 MPa and to 700°C in a gas-medium high-pressure apparatus. On heating, both the elastic bulk (K S) and shear (G) moduli decrease linearly to 350°C. By combining with extant thermal-expansion data, the values for the room-temperature K S and G, and their temperature derivatives are as follows: K 0 = 176.3(7) GPa, G 0 = 80.1(2) GPa, (∂K S/∂T) P = −0.032(3) GPa K−1 and (∂G/∂T) P = −0.012(1) GPa K−1. Between 350 and 400°C, there are abrupt increases of 1.4% in both of the elastic moduli; these closely coincide with the magnetic Curie transition that was observed by thermal analyses at about 360°C.  相似文献   

18.
This paper gives a brief account of the results of a series of oedometer tests and triaxial creep tests on frozen soils.

The oedometer tests are performed on artificially frozen sand, silt and clay. The tests also include ice as a reference material. The results are given by parameters describing the tangent deformation modulus and the time resistance against creep.

The triaxial creep tests are carried out on the artificially frozen clay, and on a permafrost clay from Spitsbergen. The data are interpreted in accordance with Hult's theory. The artificially frozen clay shows much higher creep resistance than the permafrost clay.

In addition to deformation moduli and creep parameters the routine data of the materials tested are also included.  相似文献   


19.
The compressibility at room temperature and the thermal expansion at room pressure of two disordered crystals (space group C2/c) obtained by annealing a natural omphacite sample (space group P2/n) of composition close to Jd56Di44 and Jd55Di45, respectively, have been studied by single-crystal X-ray diffraction. Using a Birch–Murnaghan equation of state truncated at the third order [BM3-EoS], we have obtained the following coefficients: V 0 = 421.04(7) Å3, K T0 = 119(2) GPa, K′ = 5.7(6). A parameterized form of the BM3 EoS was used to determine the axial moduli of a, b and c. The anisotropy scheme is β c  ≤ β a  ≤ β b , with an anisotropy ratio 1.05:1.00:1.07. A fitting of the lattice variation as a function of temperature, allowing for linear dependency of the thermal expansion coefficient on the temperature, yielded αV(1bar,303K) = 2.64(2) × 10−5 K−1 and an axial thermal expansion anisotropy of α b  ≫ α a  > α c . Comparison of our results with available data on compressibility and thermal expansion shows that while a reasonable ideal behaviour can be proposed for the compressibility of clinopyroxenes in the jadeite–diopside binary join [K T0 as a function of Jd molar %: K T0 = 106(1) GPa + 0.28(2) × Jd(mol%)], the available data have not sufficient quality to extract the behaviour of thermal expansion for the same binary join in terms of composition.  相似文献   

20.
The effect of a smooth rigid stratum, located beneath a dense sand layer, on the bearing capacity and settlement of surface and shallow strip footings is investigated using an advanced experimental model. A theoretical analysis is presented for the bearing capacity of surface footings. The results indicate that the bearing capacity reaches a minimum value at a specific sand-layer thickness. Any increase in the layer thickness above this value causes an increase in the bearing capacity up to that corresponding to a continuous media.Notation H= thickness of the sand layer - B= foundation width - N q and N = bearing capacity factors for a semi-infinite layer - N qs and N s= bearing capacity factors for a finite layer - H o /B= limiting depth - D r= relative density - = angle of soil internal friction - M= model width - D= depth of surcharge - q= bearing stress, pressure applied on the footing - q u= bearing capacity - = unit weight of sand  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号