首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献，搜索用时 31 毫秒
1.
本文研究了基于泊松小波径向基函数融合多代卫星测高及多源重力数据精化大地水准面模型的方法.分别以沿轨垂线偏差和大地水准面高高差作为卫星测高观测量,研究了使用不同类型测高数据对于大地水准面建模精度的影响.针对全球潮汐模型在浅水区域及部分开阔海域精度较低的问题,引入局部潮汐模型研究了不同潮汐模型对于大地水准面的影响.数值分析表明:相比于使用沿轨垂线偏差作为测高观测量,基于沿轨大地水准面高高差解算得到的大地水准面模型的精度更高,特别是在海域区域,其精度提高了2.3cm.由于使用沿轨大地水准面高高差作为测高观测量削弱了潮汐模型长波误差的影响,采用不同潮汐模型对大地水准面解算的影响较小.总体而言,船载重力及测高观测数据在海洋重力场的确定中呈现互补性关系,联合两类重力场观测量可以提高局部重力场的建模精度.  相似文献   

2.
Approximately nine-year data from ERS1, ERS2 and TOPEX/POSEIDON (T/P) satellite altimetry missions have been used for the recovery of gravity anomalies over the Black Sea. The Corrected Sea Surface Height product of Aviso/Altimetry has been proven to be homogeneous after a cross-over adjustment. The Least Squares Collocation method was applied in a so-called remove-restore procedure. The residual geoid heights, obtained by subtracting EGM96 geoid heights from cross-over adjusted sea surface heights, were inverted to recover residual gravity anomalies in a grid structure over the Black Sea. Finally, EGM96 free air gravity anomalies were added to the predicted residual gravity anomalies to obtain the free air gravity anomalies. In order to check the consistency with respect to an external source, these computed free air gravity anomalies were compared to ship gravity observations, and to alternative satellite altimetry derived gravity anomalies. Comparisons with the observed gravity data yielded that external consistency of the gravity anomalies computed in this study is about 3 mGal for individual ship tracks. Overall external consistency in the test area is 4.8 mGal. Comparison with other satellite altimetry derived gravity anomalies presented a good agreement.  相似文献   

3.
由于卫星观测技术的发展，现在已能利用测高大地水准面简捷可靠地研究海底构造与动力问题. 根据Geosat T2/ERM、Topex/Poseidon 和ERS 1/2测高数据给定的0°N ～45°N、100°E～150°E范围内4′×4′大地水准面，采用全球地形/均衡的重力位效应改正，计算布格、格莱尼和均衡大地水准面. 由格莱尼大地水准面反演Moho面埋深，再从均衡大地水准面起伏推算小尺度地幔流应力场. 结果表明，菲律宾海和南海显示了与磁条带、扩张脊对应或斜交的高频成分大地水准面起伏条带. 各边缘海盆的Moho面埋深有往南变浅的趋势，与菲律宾海各海盆的Moho面埋深大致相当，说明琉球—台湾—菲律宾岛弧两侧的构造动力强度基本相近. 从各种构造特征和大、中、小尺度的地幔流应力场的驱动机制，可以证明岛弧内侧的边缘海具有不同于大洋、大陆的独特构造动力格局和特征.  相似文献   

4.
Successful development of geodetic satellite missions has aroused new interest in determining global and regional gravity field based on satellite data. Satellite altimetry data enable direct determination of the geoid over sea regions. In Egypt, where land and marine geophysical data are inadequate because of rough topography and economic reasons, the use of satellite altimetry data is of special importance. The northern Red Sea region has been selected as a site for case study of the current research, after applying spectral analysis to reveal near-surface structure, the residual geoid of the studied region shows a good correlation with the known geologic features. Moreover, satellite-based gravity data enhance small-scale features and agrees well with land and marine gravity data. Thus, geoid undulation and satellite gravity data can be a complementary source of data to determine near-surface and deep structures.  相似文献   

5.
The mean dynamic topography of the surface of the North Atlantic is estimated using an inverse model of the ocean circulation constrained by hydro-graphic and altimetric observations. In the North Atlantic, altimetric observations have no significant impact on the topography estimate because of the limited precision of available geoid height models. They have a significant impact, however, when uncertainties in the density field are increased to simulate interpolation errors in regions where hydrographic data are scarce. This result, which moderates the conclusion drawn by Ganachaud and co-workers of no significant contribution of altimetric observations to the determination of the large-scale steady circulation, reflects the simple idea that altimetric data are most useful near the surface of the ocean and in areas where the hydrography is poorly determined. One application of the present inverse estimate of the mean dynamic topography is to compute a geoid height correction over the North Atlantic which reduces the uncertainty in the geoid height expanded to spherical harmonic 40 down to a level of about 5 cm.  相似文献   

6.
We present a geoid model for the area of Lake Vostok, Antarctica, from a combination of local airborne gravity, ice-surface and ice-thickness data and a lake bathymetry model. The topography data are used for residual terrain modeling (RTM) in a remove–restore approach together with GOCE satellite data. The quasigeoid is predicted by least-squares collocation (LSC) and subsequently converted to geoid heights. Special aspects of that method in presence of an ice sheet are discussed.It is well known that a body freely floating in water is in a state of hydrostatic equilibrium (HE). This usually applies, e.g., to ice shelves or sea ice. However, it has been shown that this is valid also for the ice sheet covering the subglacial Lake Vostok. Thus, we demonstrate the use of such a refined regional geoid model for glaciological and geophysical applications by means of the HE surface of that lake. The mean quadratic residual geoid signal (0.56 m) w.r.t. the GOCE background model exceeds the residual variations of the estimated apparent lake level (ALL) (0.26 m) within the central part of the lake. An approach considering the actual geopotential at the ALL has been derived and subsequently applied. In this context, downward continuation of the potential field within the ice sheet as well as the latitudinal tilt of off-geoid equipotential surfaces are discussed. In view of the accuracy of the ice-thickness measurements that dominate the total error budget of the estimated ALL these effects are negligible. Thus, the HE surface of subglacial lakes may safely be described by a constant height bias in small-scale regional applications. However, field continuation is significant with respect to the formal uncertainty of the quasigeoid, which is at the level of 5 cm given that accurate airborne gravity data (±2 mGal) are available.  相似文献   

7.
Temporal mass variations in the Earth system, which can be detected from the Gravity Recovery and Climate Experiment (GRACE) mission data, cause temporal variations of geoid heights. The main objective of this contribution is to analyze temporal variations of geoid heights over the area of Poland using global geopotential models (GGMs) developed on the basis of GRACE mission data. Time series of geoid height variations were calculated for the chosen subareas of the aforementioned area using those GGMs. Thereafter, these variations were analyzed using two different methods. On the basis of the analysis results, models of temporal geoid height variations were developed and discussed. The possibility of prediction of geoid height variations using GRACE mission data over the area of Poland was also investigated. The main findings reveal that the geoid height over the area of Poland vary within 1.1 cm which should be considered when defining the geoid model of 1 cm accuracy for this area.  相似文献   

8.
The reduction of gravity-field related quantities (e.g., gravity anomalies, geoid heights) due to the topography plays a crucial role in both geodetic and geophysical applications, since in the former it is an intermediate step towards geoid prediction and in the latter it reveals lateral as well as radial density contrasts and infers the geology of the area under study. The computations are usually carried out by employing a DTM and/or a DBM, which describe the topography and bathymetry, respectively. Errors in these DTMs/DBMs will introduce errors in the computed topographic effects, while poor spatial resolution of the topography and bathymetry models will result in aliasing effects to both gravity anomalies and geoid heights, both influencing the accuracy of the estimated solutions. The scope of this work is twofold. First, a validation and accuracy assessment of the SRTM 3″ (90 m) DTM over Greece is performed through comparisons with existing global models as well as with the Greek 450 m national DTMs. Whenever a misrepresentation of the topography is identified in the SRTM data, it is “corrected” using the local 450 m DTM. This process resulted in an improved SRTM DTM called SRTMGr, which was then used to determine terrain effects to gravity field quantities. From the fine-resolution SRTMGr DTMs, coarser models of 15″, 30″, 1′, 2′ and 5′ have been determined in order to investigate aliasing effects on both gravity anomalies and geoid heights by computing terrain effects at variable spatial resolutions. From the results acquired in two test areas, it was concluded that SRTMGr provides similar results to the local DTM making the use of other older global DTMs obsolete. The study for terrain aliasing effects proved that when high-resolution and accuracy gravity and geoid models are needed, then the highest possible resolution DTM should be employed to compute the respective terrain effects. Based on the results acquired from two the test areas a corrected SRTMGr DTM has been compiled for the entire Greek territory towards the development of a new gravimetric geoid model. Results from that analysis are presented based on the well-known remove-compute-restore method, employing land and marine gravity data, EGM08 as a reference geopotential model and the SRTMGr DTM for the computation of the RTM effects.  相似文献   

9.
Geostrophic surface velocities can be derived from the gradients of the mean dynamic topography—the difference between the mean sea surface and the geoid. Therefore, independently observed mean dynamic topography data are valuable input parameters and constraints for ocean circulation models. For a successful fit to observational dynamic topography data, not only the mean dynamic topography on the particular ocean model grid is required, but also information about its inverse covariance matrix. The calculation of the mean dynamic topography from satellite-based gravity field models and altimetric sea surface height measurements, however, is not straightforward. For this purpose, we previously developed an integrated approach to combining these two different observation groups in a consistent way without using the common filter approaches (Becker et al. in J Geodyn 59(60):99–110, 2012; Becker in Konsistente Kombination von Schwerefeld, Altimetrie und hydrographischen Daten zur Modellierung der dynamischen Ozeantopographie 2012). Within this combination method, the full spectral range of the observations is considered. Further, it allows the direct determination of the normal equations (i.e., the inverse of the error covariance matrix) of the mean dynamic topography on arbitrary grids, which is one of the requirements for ocean data assimilation. In this paper, we report progress through selection and improved processing of altimetric data sets. We focus on the preprocessing steps of along-track altimetry data from Jason-1 and Envisat to obtain a mean sea surface profile. During this procedure, a rigorous variance propagation is accomplished, so that, for the first time, the full covariance matrix of the mean sea surface is available. The combination of the mean profile and a combined GRACE/GOCE gravity field model yields a mean dynamic topography model for the North Atlantic Ocean that is characterized by a defined set of assumptions. We show that including the geodetically derived mean dynamic topography with the full error structure in a 3D stationary inverse ocean model improves modeled oceanographic features over previous estimates.  相似文献   

10.
The National Survey and Cadastre - Denmark (KMS) has for several years produced gravity anomaly maps over the oceans derived from satellite altimetry. During the last four years, KMS has also conducted airborne gravity surveys along the coast of Greenland dedicated to complement the existing onshore gravity coverage and fill in new data in the very-near coastal area, where altimetry data may contain gross errors. The airborne surveys extend from the coastline to approximately 100 km offshore, along 6000 km of coastline. An adequate merging of these different data sources is important for the use of gravity data especially, when computing geoid models in coastal regions.The presence of reliable marine gravity data for independent control offers an opportunity to study procedures for the merging of airborne and satellite data around Greenland. Two different merging techniques, both based on collocation, are investigated in this paper. Collocation offers a way of combining the individual airborne gravity observation with either the residual geoid observations derived from satellite altimetry or with gravity derived from these data using the inverse Stokes method implemented by Fast Fourier Transform (FFT).  相似文献   

11.
The altimetric satellite signal is the sum of the geoid and the dynamic topography, but only the latter is relevant to oceanographic applications. Poor knowledge of the geoid has prevented oceanographers from fully exploiting altimetric measurements through its absolute component, and applications have concentrated on ocean variability through analyses of sea level anomalies. Recent geodetic missions like CHAMP, GRACE and the forthcoming GOCE are changing this perspective. In this study, data assimilation is used to reconstruct the Tropical Pacific Ocean circulation during the 1993–1996 period. Multivariate observations are assimilated into a primitive equation ocean model (OPA) using a reduced order Kalman filter (the Singular Evolutive Extended Kalman filter). A 6-year (1993–1998) hindcast experiment is analyzed and validated by comparison with observations. In this experiment, the new capability offered by an observed absolute dynamic topography (built using the GRACE geoid to reference the altimetric data) is used to assimilate, in an efficient way, the in-situ temperature profiles from the TAO/TRITON moorings together with the T/P and ERS1&2 altimetric signal. GRACE data improves compatibility between both observation data sets. The difficulties encountered in this regard in previous studies such as Parent et al. (J Mar Syst 40–41:381–401, 2003) are now circumvented. This improvement helps provide more efficient data assimilation, as evidenced, by assessing the results against independent data. This leads in particular to significantly more realistic currents and vertical thermal structures.  相似文献   

12.
Sediments deposited during glacial-interglacial cycles through the Early to Mid-Pleistocene in the North Sea are chronologically poorly constrained. To contribute to the chronology of these units, amino acid racemization (AAR) and strontium (Sr) isotope analyses have been performed on samples from four shallow borings and one oil well along a transect in the northern North Sea. D/L Asp (aspartic acid) values obtained through reverse-phase liquid chromatography in the benthic foraminiferal species Elphidium excavatum is focused on because of consistent results and a good stratigraphic distribution of this benthic species. For the Early Pleistocene, an age model for the well 16/1–8, from the central part of the northern North Sea based on Sr ages allows for dating of the prograding wedges filling the pre-Quaternary central basin. A regional calibration curve for the racemization of Asp in Elphidium excavatum is developed using published ages of radiocarbon-dated samples and samples associated with the previously identified Bruhnes/Matuyama (B/M) paleomagnetic boundary and a Sr age from this study. Based on all the available geochronological evidence, samples were assigned to marine oxygen isotope stages (MIS) with uncertainties on the order of 10–70 ka.Sr ages suggest a hiatus of <2 million years (Ma) possibly due to non-deposition or low sedimentation between the Utsira Formation (Pliocene) and the Early Pleistocene. An increase in sedimentation rates around 1.5 ± 0.07 Ma (∼MIS 51) may partly be due to sediment supply from rivers from the south-east and partly due to the extension of ice sheet around 1.36 ± 0.07 Ma from the Norwegian coast to the central North Sea. A possible basin-wide glaciation occurred around 1.1 Ma (∼ MIS 32) (upper regional unconformity/top of unit Q4 in this study), resulting in erosion and regional unconformity. Two interglacials in the Norwegian Channel have been dated: the Radøy Interglacial to 1.07 ± 0.01 Ma (possibly MIS 31, the ‘super interglacial’), and the Norwegian Trench Interglacial to 0.50 ± 0.02 Ma (possibly MIS 13). A massive till unit identified at the same stratigraphic level in all shallow borings may partly represent an extensive MIS 12 glaciation. This study shows that the combined use of amino acid racemization data and Sr isotope chronology can refine the chronological ambiguities of Quaternary North Sea sediments related partly to the impact of glacial processes.  相似文献   

13.
Presently, two satellite missions, Gravity Recovery and Climate Experiment (GRACE) and Gravity field and steady-state Ocean Circulation Explorer (GOCE), are making detailed measurements of the Earth’s gravity field, from which the geoid can be obtained. The mean dynamic topography (MDT) is the difference between the time-averaged sea surface height and the geoid. The GOCE mission is aimed at determining the geoid with superior accuracy and spatial resolution, so that a more accurate MDT can be estimated. In this study, we determine the mean positions of the Antarctic Circumpolar Current fronts using the purely geodetic estimates of the MDT constructed from an altimetric mean sea surface and GOCE and GRACE geoids. Overall, the frontal positions obtained from the GOCE and GRACE MDTs are close to each other. This means that these independent estimates are robust and can potentially be used to validate frontal positions obtained from sparse and irregular in situ measurements. The geodetic frontal positions are compared to earlier estimates as well as to those derived from MDTs based on satellite and in situ measurements and those obtained from an ocean data synthesis product. The position of the Sub-Antarctic Front identified in the GOCE MDT is found to be in better agreement with the previous estimates than that identified in the GRACE MDT. The geostrophic velocities derived from the GOCE MDT are also closer to observations than those derived from the GRACE MDT. Our results thus show that the GOCE mission represents an improvement upon GRACE in terms of the time-averaged geoid.  相似文献   

14.
Turkish regional geoid models have been developed by employing a reference earth gravitational model, surface gravity observations and digital terrain models. The gravimetric geoid models provide a ready transformation from ellipsoidal heights to the orthometric heights through the use of GPS/leveling geoid heights determined through the national geodetic networks. The recent gravimetric models for Turkish territory were computed depending on OSU91 (TG-91) and EGM96 (TG-03) earth gravitational models. The release of the Earth Gravitational Model 2008 (EGM08), the collection of new surface gravity observations, the advanced satellite altimetry-derived gravity over the sea, and the availability of the high resolution digital terrain model have encouraged us to compute a new geoid model for Turkey. We used the Remove-Restore procedure based on EGM08 and applied Residual Terrain Model (RTM) reduction of the surface gravity data. Fast Fourier Transformation (FFT) was then used to obtain the residual quasigeoid from the reduced gravity. We restored the individual contributions of EGM08 and RTM to the whole quasi-geoid height (TQG-09). Since the Helmert orthometric height system is adopted in Turkey, the quasi-geoid model (TQG-09) was then converted to the geoid model (TG-09) by making use of Bouguer gravity anomalies and digital terrain model. After all we combined a gravimetric geoid model with GPS/leveling geoid heights in order to obtain a hybrid geoid model (THG-09) (or a transformation surface) to be used in GPS applications. The RMS of the post-fit residuals after the combination was found to be ± 0.95 cm, which represents the internal precision of the final combination. And finally, we tested the hybrid geoid model with GPS/leveling data, which were not used in the combination, to assess the external accuracy. Results show that the external accuracy of the THG-09 model is ± 8.4 cm, a precision previously not achieved in Turkey until this study.  相似文献   

15.
A mathematical model used for determination of a local geoid model by combining airborne gravity disturbances and the Earth Gravitational Model 2008 (EGM08) is shortly reviewed. The precision of the estimated local geoid model of Taiwan is tested by its comparison with the “real” geoid at Global Satellite Navigation Systems (GNSS)/levelling points. The same comparison at GNSS/levelling points is done for the geoid evaluated only by using EGM08. Conclusions concerning a rate of improvement of the “global” geoid from EGM08 using the “local” geoid from airborne gravity data are presented.  相似文献   

16.
GOCE, Satellite Gravimetry and Antarctic Mass Transports   总被引：1，自引：0，他引：1  
In 2009 the European Space Agency satellite mission GOCE (Gravity Field and Steady-State Ocean Circulation Explorer) was launched. Its objectives are the precise and detailed determination of the Earth’s gravity field and geoid. Its core instrument, a three axis gravitational gradiometer, measures the gravity gradient components V xx , V yy , V zz and V xz (second-order derivatives of the gravity potential V) with high precision and V xy , V yz with low precision, all in the instrument reference frame. The long wavelength gravity field is recovered from the orbit, measured by GPS (Global Positioning System). Characteristic elements of the mission are precise star tracking, a Sun-synchronous and very low (260 km) orbit, angular control by magnetic torquing and an extremely stiff and thermally stable instrument environment. GOCE is complementary to GRACE (Gravity Recovery and Climate Experiment), another satellite gravity mission, launched in 2002. While GRACE is designed to measure temporal gravity variations, albeit with limited spatial resolution, GOCE is aiming at maximum spatial resolution, at the expense of accuracy at large spatial scales. Thus, GOCE will not provide temporal variations but is tailored to the recovery of the fine scales of the stationary field. GRACE is very successful in delivering time series of large-scale mass changes of the Antarctic ice sheet, among other things. Currently, emphasis of respective GRACE analyses is on regional refinement and on changes of temporal trends. One of the challenges is the separation of ice mass changes from glacial isostatic adjustment. Already from a few months of GOCE data, detailed gravity gradients can be recovered. They are presented here for the area of Antarctica. As one application, GOCE gravity gradients are an important addition to the sparse gravity data of Antarctica. They will help studies of the crustal and lithospheric field. A second area of application is ocean circulation. The geoid surface from the gravity field model GOCO01S allows us now to generate rather detailed maps of the mean dynamic ocean topography and of geostrophic flow velocities in the region of the Antarctic Circumpolar Current.  相似文献   

17.
An airborne gravity campaign was carried out at the Dome-C survey area in East Antarctica between the 17th and 22nd of January 2013, in order to provide data for an experiment to validate GOCE satellite gravity gradients. After typical filtering for airborne gravity data, the cross-over error statistics for the few crossing points are 11.3 mGal root mean square (rms) error, corresponding to an rms line error of 8.0 mGal. This number is relatively large due to the rough flight conditions, short lines and field handling procedures used. Comparison of the airborne gravity data with GOCE RL4 spherical harmonic models confirmed the quality of the airborne data and that they contain more high-frequency signal than the global models. First, the airborne gravity data were upward continued to GOCE altitude to predict gravity gradients in the local North-East-Up reference frame. In this step, the least squares collocation using the ITGGRACE2010S field to degree and order 90 as reference field, which is subtracted from both the airborne gravity and GOCE gravity gradients, was applied. Then, the predicted gradients were rotated to the gradiometer reference frame using level 1 attitude quaternion data. The validation with the airborne gravity data was limited to the accurate gradient anomalies (TXX, TYY, TZZ and TXZ) where the long-wavelength information of the GOCE gradients has been replaced with GOCO03s signal to avoid contamination with GOCE gradient errors at these wavelengths. The comparison shows standard deviations between the predicted and GOCE gradient anomalies TXX, TYY, TZZ and TXZ of 9.9, 11.5, 11.6 and 10.4 mE, respectively. A more precise airborne gravity survey of the southern polar gap which is not observed by GOCE would thus provide gradient predictions at a better accuracy, complementing the GOCE coverage in this region.  相似文献   

18.
From the late 1990s, many studies on local geoid construction have been made in South Korea. However, the precision of the previous geoid has remained about 15 cm due to distribution and quality problems of gravity and GPS/levelling data. Since 2007, new land gravity data and GPS/levelling data have been obtained through many projects such as the Korean Land Spatilaization, Unified Control Point and Gravity survey on the Benchmark. The newly obtained data are regularly distributed to a certain degree and show much better improvement in their quality. In addition, an airborne gravity survey was conducted in 2008 to cover the Korean peninsula (South Korea only). Therefore, it is expected that the precision of the geoid could be improved. In this study, the new South Korean gravimetric geoid and hybrid geoid are presented based on land, airborne, ship‐borne, altimeter gravity data, geopotential model and topographic data. As for the methodology, the general remove‐restore approach was applied with the best chosen parameters in order to produce a precise local geoid. The global geopotential model EGM08 was used to remove the low‐frequency components using degree and order up to 360 and the short wavelength part of the gravity signal was dealt with by using the Shuttle Radar Topography Mission data. The parameters determined empirically in this study include for Stokes’ integral 0.5° and for Wong‐Gore kernel 110–120°, respectively and 10 km for both the Bjerhammar sphere depth and attenuation factor. The final gravimetric geoid in South Korea ranges from 20–31 m with a precision of 5.45 cm overall compared to 1096 GPS/levelling data. In addition, the South Korean hybrid geoid produces 3.46 cm and 3.92 cm for degrees of fitness and precision, respectively and a better statistic of 2.37 cm for plain and urban areas was achieved. The gravimetric and hybrid geoids are expected to improve further when the refined land gravity data are included in the near future.  相似文献   

19.
通过联合全球重力位模型(EGM2008)、航空重力扰动数据和剩余地形模型(RTM)数据,基于频谱域(二维FFT变换)和空间域(Stokes数值积分)算法对毛乌素测区GT-2A航空重力测量系统采集的空中测线后处理重力扰动数据进行解算,构建了该地区的航空重力梯度扰动全张量.(1)残余航空重力扰动延拓结果表明:残余航空重力扰动经向下延拓至大地水准面,再向上延拓至航空高度后与原数据差值的标准差为1.0078 mGal,考虑边缘效应后,内缩计算范围得到的差值标准差减小至0.1269 mGal.(2)基于残余重力扰动数据(原航空高度数据及向下延拓数据),通过不同方案解算得到的梯度扰动结果表明:两种方案得到的研究区域重力梯度扰动各分量之差的最大标准差为6.4798E(Γ_(yz)分量),最小标准差为2.6968E(Γ_(xy)分量),内缩计算范围后得到的差值标准差最大值为1.8307E(Γ_(zz)分量),最小值为0.7223E(Γ_(yz)分量).本文的思路和方法可为未来我国自主构建航空重力梯度标定场提供参考.  相似文献   

20.
我国在海域开展了大规模的航空重力勘探,这些资料对构建高精度大地水准面具有重要价值.基于此,本文提出一种利用海域航空重力测量数据快速构建大地水准面的方法.该方法基于移去-恢复法思想,利用位场最小曲率方法对航空重力数据进行高精度向下延拓并获取相应的扰动位,实现航空重力测量快速构建海域大地水准面.与斯托克斯积分计算相比,采用了处理效率更高的频率域位场转换,解决了向下延拓及垂向积分时航空重力异常数据空白及扩边问题,具有较高的位场转换精度.本文应用EGM2008模拟航空重力数据进行模型验证,计算结果与其给出的水准面的精度相当;同时,也选取GRAV-D计划的航空重力数据进行实际验证,计算结果与xGEOID18B水准面模型精度基本一致.模型验证和实际应用验证了本方法的实用性.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号