首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献，搜索用时 78 毫秒
1.
沸石的活化处理及其对铅、钴的吸附性研究   总被引：6，自引：2，他引：4  
易发成 《矿物岩石》2005,25(3):118-121
通过对沸石的活化方法和其基本物化性能（主要包括化学成分、阳离子交换容量、密度、比表面积、孔径、渗透系数及热稳定性）及Pb^2＋,Co^2＋离子的吸附性能的初步研究认识到：1）经过酸化并经热处理后的沸石的阳离子交换容量（CEC）明显高于未经处理的原土;2）通过实验得出粒度为100目的天然沸石经酸活化处理后在300C下热活化,1．5h后测得离子交换量为最佳;3）沸石的密度为1．789g／cm^3;渗透系数为0．087cm／s（20℃）;体积平均粒径为13μm;比表面积为190．67m^2／g,平均孔径为102．27nm;4）沸石对重金属离子的吸附实验表明沸石对重金属离子Pb^2＋的吸附性能优于Co^2＋,20min时Pb^2＋和Co^2＋的吸附比（Rd）分别为20238．8ml／g及63．8ml／g;Pb^2＋和Co^2＋去除率分别为99．50％和40．00％。  相似文献   

2.
毛飞  易发成 《矿物岩石》2006,26(4):101-104
采用间歇法研究不同复合矿物材料对模拟核素C s ,S r2 及S r2 C s 混合离子的吸附特征,结果表明:复合材料N系列对C s 吸附量呈线性递减;Z系列的Z1,Z2,Z3对C s 吸附量呈线性增加,而其后基本不变;N 1比Z1吸附C s 效果好。N系列和Z系列对S r2 的吸附分别呈线性递减和递增变化。在S r2 C s 竞争吸附中,低价态的C s 相对单C s 溶液条件下吸附量变小,材料Z1总吸附量最大。  相似文献   

3.
土-膨润土系竖向隔离墙广泛应用于工业污染场地和地下水修复工程。通过坍落度和一维压缩固结试验研究添加沸石对黏性土-膨润土竖向隔离墙材料的工作性,以及压缩和渗透特性。黏性土选用高岭土,沸石-高岭土-膨润土试样中沸石掺量为2%～40%。试验结果与以往沸石-砂-膨润土竖向隔离墙材料以及击实沸石-膨润土混合土研究结果进行对比,明确沸石掺量和粒径对压缩和渗透特性的作用规律。试验结果显示,满足隔离墙材料施工要求的含水率范围随沸石掺量增加而增大,并处于液限的0.96～1.18倍。添加细颗粒沸石对试样的压缩指数和渗透系数影响较小,渗透系数小于10-9 m/s。相反,添加粗颗粒沸石将导致微孔隙尺寸增大,并形成水能够通过的沸石网架结构,将显著增大渗透系数。试样渗透系数能够通过考虑孔隙比和液限的经验公式进行良好的预测。  相似文献   

4.
对四川三台钙基膨润土的基本物化性能和对Pb^2 ，Co^2 离子的吸附性能作了初步的研究。基本物化性能主要包括化学成分、阳离子交换容量、密度、比表面积、孔径、渗透系数及热稳定性。通过实验得出：1)经过钠化改型并酸化处理后的膨润土的阳离子交换容量(CEC)明显高于未经处理的原土；2)膨润土的最佳酸活化条件为在96℃左右以15％的硫酸活化4小时的性能最佳；3)膨润土土的密度为2．11g／cm^3，颗粒密度钠化土为1．996g／cm^3，原土为2．079g／cm^3；渗透系数为0．013cm／s(20C)；体积平均粒径为30．950μm；比表面积为329．7482m^2／g，平均孔径为33．238nm；4)膨润土对对重金属离子的吸附实验，得出膨润土对重金属离子Pb^2 的吸附性能优于Co^2 ，Pb^2 和Co^2 的吸附比(Rd)分别为167．8ml／g及53．3ml／g；Pb^2 和Co^2 去除率(r)分别为45．87%和21．20％。  相似文献   

5.
斜发沸石对钾离子的吸附/解吸动力学研究   总被引：1，自引：0，他引：1  
以KCl为钾源、新疆某地所产斜发沸石为吸附剂,研究斜发沸石对K+的动力吸附与解吸效果,并探讨吸附时间、K+初始浓度与吸附量的关系。用pH=5的HCl溶液和(Ca2++Mg2+)浓度/(mmol.L-1)为1.6,3.2,6.4,12.8,19.2,25.6的混合溶液对饱和吸附了K+的斜发沸石进行解吸,实验结果表明:沸石对K+的吸附在4min能达到最大吸附率的96%,30min内达到平衡。Langmuir吸附等温式能对吸附曲线进行很好的描述。单位质量沸石对K+的最大吸附量为44.53×10-3,以阳离子交换吸附为主。pH=5的HCl溶液对K+的解吸量最小,随解吸溶液中(Ca2++Mg2+)浓度增加,解吸滞后系数减小,解吸速率远小于吸附速率。解吸量的自然对数与解吸时间的自然对数呈现明显的线性关系,用指数方程对(Ca2++Mg2+)浓度为25.6mmol/L的解吸曲线进行拟合,R=0.998,拟合方程为qt=3.890t0.210。理论上将吸附的K+全部解吸出来需要74.4d。  相似文献   

6.
采用盐熔融法,将Zn2+交换丝光沸石分子筛制备Zn2+改性丝光沸石吸附材料。通过该材料对甲基橙的吸附动力学和吸附热力学研究,了解其吸附机理。研究结果表明:Zn2+改性丝光沸石对甲基橙的吸附动力学可用拟二级动力学方程来描述,计算值与试验值吻合较好,相关系数达到0.99;Zn2+改性丝光沸石对甲基橙的吸附等温线均符合Langmuir和Freundlich方程,室温下相关系数均大于0.9。根据不同温度下的热力学平衡常数,推算出Zn2+改性丝光沸石对甲基橙的吸附吉布斯自由能变ΔG0<0,吸附焓变ΔH0>0,表明吸附为自发的吸附过程,升温有利于吸附的进行,且吸附过程主要是物理吸附。  相似文献   

7.
在蒙脱石有机改性体系中,交换液酸碱度对蒙脱石荷电性以及十八烷基三甲基氯化铵(OTAC)的电离度影响很大,进而影响OTAC在蒙脱石中的吸附以及制备复合物的凝胶粘度。研究发现,在pH=3的强酸性交换体系中,蒙脱石端面可变电荷为正电荷,OTAC阳离子和蒙脱石之间静电斥力的存在不利于OTAC在蒙脱石上的吸附,吸附量和吸附率分别是0.943CEC和85.7%,制备复合物的凝胶粘度最低,分别是μ0min为45.67Pa·s,μ30min为16.52Pa·s;在pH=10的弱碱性交换体系中,由于蒙脱石层面和端面均带有负电荷,静电引力更有利于OTAC阳离子在蒙脱石层间交换及表面吸附,其吸附量和吸附率最高,分别为1.097CEC和99.71%,制备复合物的凝胶粘度也较高,分别是μ0min为95.93Pa·s,μ30min为37.67Pa·s;在强碱性交换体系中,当pH=11和13时,蒙脱石对OTAC的吸附量和吸附率降低明显,吸附量分别为1.08CEC和1.058CEC,吸附率分别降到98.20%和96.18%,对应复合物的μ0min分别为96.52Pa·s和93.52Pa·s,μ30min分别为36.57Pa·s和36.53Pa·s,究其原因由于交换液中OTAC阳离子和高浓度的钠离子在蒙脱石层间和表面存在竞争吸附导致蒙脱石层间钠离子的交换难度加大。  相似文献   

8.
天然沸石吸附性能与阳离子组分之间的关系   总被引：7，自引：0，他引：7  
吸附性能是沸石矿物的重要特性之一，也是相关领域应用的重要依据。以嫩江、海林和穆棱三大沸石矿床为例，通过对天然沸石矿的化学成分、沸石类型、矿石品位（CEC值）、比表面积及吸附性能的系统研究与对比分析，总结天然沸石矿附吸性能差异变化规律与原因。研究表明，天然沸石对气体CO2、H2S、SO2、NO2和气态H2O的吸附容量均与其（CaO MgO)/(Na2O K2O)比值之间呈正相关性关系，富二价阳离子组分者吸附容量大，富一价阳离子组分者吸附容量较小。据此，可作为天然沸石矿吸附性能预测评价的重要依据。  相似文献   

9.
天然沸石的铵吸附容量研究   总被引：1，自引：0，他引：1       下载免费PDF全文
为了探讨天然沸石对NH4^＋的吸附规律,以江苏镇江的天然沸石为实验对象,测试其矿物组成与化学成分,通过静态摇床法实验研究其对铵离子的吸附特性及阳离子的交换特性,进行吸附等温线实验。结果表明,实验沸石对NH4^＋吸附等温线符合Langmuir公式。根据数学分析,确定沸石的铵吸附容量。  相似文献   

10.
无机改性膨润土防渗层性能研究   总被引：1，自引：0，他引：1  
通过实验室实验确定2mol/L氯化镁、0.5mol/L硫酸和450℃高温为天然钠基膨润土盐改性、酸改性和高温改性的最佳条件。采用上述3种无机改性方式填装防渗层,就其对垃圾渗滤液中主要污染物去除的有效性和控制垃圾渗滤液渗透的可行性进行研究。实验结果显示:3种无机改性膨润土的吸附能力和容量有所提高;渗透系数可达到1×10-7cm/s以下,可以作为"反应型"防渗层材料;在相同渗透量下,高温改性膨润土对垃圾渗滤液中主要污染物的去除效果最好,其次是酸改性膨润土,盐改性膨润土最差。  相似文献   

11.
The reaction chlorite+dolomite=spinel+ forsterite+calcite+CO2+H2O has been studied with hydrothermal equipment technique in a C-O-H fluid at P fluid=1,000, 2,000 and 3,000 bars and fo2 controlled by NB or QFM buffer. The equilibrium conditions for the reaction has been determined as log K=–57,119/T+95.77+0.9860(P-1)/T(bar,°K). The mineral mixtures had an excess of dolomite. The composition of the chlorite among the reaction products has been analysed and found to have a higher Al/Si ratio than clinochlore.  相似文献   

12.
Hydrothermal experiments with mixtures of synthetic minerals have shown the reversibility of the reaction 5 phlogopite + 6 calcite + 24 quartz = 3 tremolite + 5 K-feldspar + 2 H2O + 6 CO2. In an isobaric T – diagram the equilibrium curve reaches a maximum at = 0,75. The P, T-values for this maximum are: 2 kb-523°; 4 kb-585°; 6 kb-625°; P±5%, T±10° C. These results give a first approximation of the P, T conditions responsible for a similar mineral reaction which has been recorded from natural metamorphic assemblages.

Herrn Prof. H. G. F. Winkler danke ich für anregende Diskussionen, desgleichen Herrn Dr. D. Puhan für wichtige Hinweise und Mitteilung seiner exp. Daten. Herrn Prof. V. Trommsdorff und Herrn P. H. Thompson bin ich für petrographische Angaben zu Dank verpflichtet. Der Aufbau der Hydrothermalanlage und die Finanzierung der laufenden Untersuchungen wurde aus den Mitteln des Fonds zur Förderung der wissenschaftlichen Forschung ermöglicht. Für diese Unterstützung gilt daher mein besonderer Dank.  相似文献   

13.
The reaction 2 epidote+2 calcite+3 wollastonite3 grossular-andraditess+ 2 CO2+1 H2O has been explored by hydrothermal experiments at a total fluid pressure of 1000 bars. For a grossular-andraditess of andradite 25 composition, the isobaric univariant curve passes through the points 458°C: XCO2=0.00; 521°C: XCO2=0.026; 523°C: XCO2=0.052; 526°C: 0.088; 528°C: XCO2=0.104. This curve intersects the isobaric univariant curve of the reaction calcite+quartz+[H2O] wollastonite+CO2+[H2O] at the isobaric invariant point around 528°C and XCO2=0.12. At higher values of XCO2, this reaction is replaced by another one, namely: 2 epidote+5 calcite+3 quartz3 grossular-andraditess+5 CO2+ 1 H2O. It is demonstrated that both the reactions do actually take place during the metamorphism of calcareous rocks. The petrologic significance of contrasted sequence of reactions within this system observed by various workers is also discussed.  相似文献   

14.
Six equilibria among quartz, plagioclase, biotite, muscovite, and garnet were empirically calibrated using mineral composition data from 43 samples having the assemblage quartz+muscovite+biotite+garnet+plagioclase+Al2SiO5 (sillimanite or kyanite). Pressures and temperatures in the data set used for calibration were determined through the simultaneous application of garnet-biotite geothermometry and garnet-quartz-plagioclase-Al2SiO5 geobarometry. Thermodynamic expressions for four of the six equilibria incorporate interaction parameters that model non-ideality in the mixing of cations in the octahedral sites of both muscovite and biotite. With pressure chosen as the dependent variable, multiple regression was used to solve for unknowns in the equilibrium thermodynamic expressions. The regressions yielded multiple correlation coefficients ranging from 0.983 to 0.999, with corresponding standard deviations of 338 and 92 bars in the residuals. The standard deviations in the residuals may be explained largely or entirely by the propagation of errors associated with electron microprobe analysis. These equilibria enable the determination of pressures from equilibrium assemblages of quartz+garnet+plagioclase+muscovite+biotite, and give results closely comparable to the experimentally calibrated garnet-quartz-plagioclase-Al2SiO5 geobarometer. Geobarometric applications should be restricted to rocks in which equilibrium constants and compositional variables fall within the same ranges as those used for calibration.  相似文献   

15.
The equilibrium curve for the reaction 3 dolomite + 1 K-feldspar + 1 H2O=1 phlogopite + 3 calcite + 3 CO2 was determined experimentally at a total gas pressure of 2000 bars using two different methods.
  1. In the first case water alone was added to the reactants. The CO2 component of the gas phase was producted solely by the reaction under favourable P-T conditions. This manner of carrying out the reaction is called the “water method”. With this method sufficient time must be allowed for the gas phase to attain a constant composition (see Fig. 1). Reverse reactions were carried out using reaction products of the forward reaction.
  2. In the second case silver oxalate + water were added to the reactants. Breakdown of the silver oxalate leads to formation of a CO2-H2O gasphase of definite composition. At constant temperature and gas pressure the \(X_{{\text{CO}}_{\text{2}} } \) determines whether the reaction products will be phlogopite + calcite or dolomite + K-feldspar. In this case it is not necessary to wait for equilibrium to be attained. This method is abbreviated the “oxalate method”. Reactants for reverse reactions are not identical with the products of the forward reaction.
At high temperatures the results of the two different methods agree well (see Tables 1 and 2). Equilibrium was attained in one case at 490° C and \(X_{{\text{CO}}_{\text{2}} } \) of approximately 0.77, and in the other case at 520° C and \(X_{{\text{CO}}_{\text{2}} } \) of 0.90. At lower temperatures there are considerable differences in the results. With the water method an \(X_{{\text{CO}}_{\text{2}} } \) of about 0.25 was reached at 450° C. With the oxalate method dolomite K-feldspar and water still react with each other at even higher \(X_{{\text{CO}}_{\text{2}} } \) values. Phlogopite, calcite and CO2 are formed together with metastable talc. There are no criteria to indicate which of the methods is the correct one at lower temperatures and in Fig. 2, therefore, both equilibrium curves are plotted.  相似文献   

16.
何涛 《铀矿地质》2002,18(5):318-320
本介绍了用VC＋＋对MAPGIS进行二次开发的方法和基本函数以及软件开发实例。  相似文献   

17.
The color and spectroscopic properties of ironbearing tourmalines (elbaite, dravite, uvite, schorl) do not vary smoothly with iron concentration. Such behavior has often been ascribed to intervalence charge transfer between Fe2+ and Fe3+ which produces a new, intense absorption band in the visible portion of the spectrum. In the case of tourmaline, an entirely different manifestation of the interaction between Fe2+ and Fe3+ occurs in which the Fe2+ bands are intensified without an intense, new absorption band. At low iron concentrations, the intensity of light absorption from Fe2+ is about the same for E∥c and E⊥c polarizations, but at high iron concentrations, the intensity of the E⊥c polarization increases more than ten times as much as E∥c. This difference is related to intensification of Fe2+ absorption by adjacent Fe3+. Extrapolations indicate that pairs of Fe2+-Fe3+ have Fe2+ absorption intensity ～200 times as great as isolated Fe2+. Enhanced Fe2+ absorption bands are recognized in tourmaline by their intensity increase at 78 K of up to 50%. Enhancement of Fe2+ absorption intensity provides a severe limitration on the accuracy of determinations of Fe2+ concentration and site occupancy by optical spectroscopic methods. Details of the assignment of tourmaline spectra in the optical region are reconsidered.  相似文献   

18.
Optical absorption spectra are presented for taramellite, traskite and neptunite, all of which have both Fe2+ and Ti4+ as major elements. The spectra of each of these minerals are dominated by a single, intense absorption band in the 415 to 460 nm region with 7000 to 9000 cm?1 halfwidth. These transitions, assigned to Fe2+-Ti4+ intervalence charge transfer, showed little difference in intensity at 80 and 300 K and have molar absorptivities which range from ～100 to ～1300 M?1 cm?1. The Fe2+-Ti4+ absorptions in these standards generally compare well to other mineral spectra in which Fe2+ — Ti4+ intervalence absorption has previously been proposed with the exception of the most cited example, blue corundum.  相似文献   

19.
Under hydrous conditions the stability field of the assemblage Mg-cordierite+K feldspar+quartz is limited on its low-temperature side by the breakdown of cordierite+K feldspar into muscovite, phlogopite and quartz, whereas the high-temperature limit is given by eutectic melting. The compatibility field of the assemblage ranges from 530° C to 745° C at 1 kbar , from 635 to 725° C at 3 kbars , from 695 to 725° C at 5 kbars and terminates at 5.5 kbars . Most components not considered in the model system will tend to restrict this field even more. However, the condition < P total will increase the range of stable coexistence drastically, making the assemblage common at elevated temperatures from contact metamorphic rocks up to intermediate pressure granulites of appropriate bulk composition.  相似文献   

20.
本文选用吉林省九台、小梨河、净月产地的膨润土为原料,测试了不同粒级的膨润土对Pb 2、Cd 2、Cr 6离子的吸附时间、吸附温度、吸附量,同时,又在模拟人胃条件下进行了试验,结果证实膨润土可以作为药用赋形剂。  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号