共查询到20条相似文献，搜索用时 31 毫秒
1.
针对传统的岩体强度参数估算方法考虑风化程度的研究成果较少的不足,引入弹性波速比λ,提出了岩体强度参数的估算方法。以贵州省二叠系两种典型岩体(灰岩和泥岩)为例,讨论了参数λ和正应力σn对岩体强度参数的影响。主要研究成果为:基于弹性波速比与Hoek-Brown强度准则,探讨了不同风化程度岩体抗剪强度参数折减系数的确定方法;研究了正应力与弹性波速比对不同风化程度灰岩与泥岩岩体瞬时抗剪强度参数的影响,结果表明,岩体所处的环境与风化程度是影响岩体剪切强度参数的主要因素;通过多项式拟合,建立了灰岩与泥岩扰动与未扰动情况下不同风化程度强度折减系数的计算公式,从理论上探讨了两种主要岩体不同风化程度对强度参数的影响。 相似文献
2.
This paper made a research about the change rule of elastic wave velocity with stress applied on rock from theoretical and experimental aspect. Firstly, a mathematical model of P-wave velocity and confining pressure of rock was set up from the point of acoustoelastic character. Effect of axial stress on P-wave velocity in granite and sandstone during uniaxial compression process was studied experimentally by using GAW-2000 rock mechanical testing system and RSM-SY5 ultrasonic wave testing system, and the relation curves of axial stress with P-wave velocity were obtained. Based on test data, acoustoelastic theoretical formulas of granite and sandstone were established and the best empirical formulas were fitted by using regression method. Meanwhile, a comparative analysis of the empirical and theoretical calculated values was carried out. Finally, the reliability of applying acoustoelastic theoretical formula in hard rock range was further verified based on the experimental data of granitic gneiss. The results show that the P-wave velocity experiences a rapid increase, gentle increase and then a sharp fall during the uniaxial compression process. The B-value in acoustoelastic theoretical formula (proportion coefficient determined by elastic modulus and third-order elastic constant) decreases exponentially with axial stress. The acoustoelastic theoretical formula can effectively reflect the relationship between rock acoustic velocity and stress within the allowable error, which can be the theoretical foundation of acoustoelastic geo-stress measurement of subsurface rock mass. 相似文献
3.
4.
基于线弹性断裂力学裂隙面张开位移及剪切位移理论公式,考虑裂隙存在常法向和常切向刚度情况,研究了含单个裂隙岩体加载过程中由于裂隙存在而附加的弹性应变能。基于应变能等效方法并假设两种裂隙变形模型--非均匀变形模型和均匀变形模型,研究了二维非贯通裂隙岩体的等效杨氏模量和等效剪切模量解析表达式。研究结果表明,对于贯通裂隙规则分布情况,均匀变形模型得到的解析解与Amadei等的结果一致;对于非贯通裂隙正态分布情况,考虑裂隙相互作用的非均匀变形模型解明显低估裂隙岩体的等效杨氏模量和等效剪切模量,而考虑裂隙相互作用的均匀变形模型解与有限元数值解的偏差在10%以内。得到的解析表达式在一定条件下可以作为裂隙岩体等效弹性模量评价方法之一。 相似文献
5.
M. S. A. Siddiquee M. S. Islam F. Tatsuoka 《Geotechnical and Geological Engineering》2013,31(2):627-645
A phenomenological model has been developed for soft rock based on the results of a series of triaxial compression (TC) tests conducted on Kobe sandstone with a very high precision measurement. From the analysis and interpretation of the test results, it has been found that small strain Young’s modulus (Ee) was a function of the major principal stress. Ee for elastic strains of soft rock was assumed to be cross-anisotropic. A damage function has been used to derive the appropriate elastic Young’s modulus when subjected to shear loading. As the basic stress–strain relation, the relationship between the tangent modulus and the shear stress level was used. The differential form of which was subsequently integrated by a 4th order Runge–Kutta solver to obtain the stress–strain relation. The model of soft rock is based on an isotropic strain hardening elasto-plastic framework which takes into account the pressure sensitivity, cross-anisotropy, degradation of Young’s modulus with the degree of mobilized shear stress and the nonlinearity of the shear stress-shear strain relationship. Although the model was developed from the analysis of the TC tests results of Kobe sandstone, it was also applied to the other types of soft rock or stiff geomaterials. Plate loading tests were conducted at a level of 61 m below the ground level at the bottom of a large excavated shaft at four locations. Finally, the model was used to simulate the plate loading test results successfully. This model was successfully calibrated with Akashi sandstone and applied in the simulation for the settlement of Akashi-Kaikyo Bridge piers. The simulations were carried out for both drained and undrained condition by changing the Poisson’s ratio. The layering information beneath the foundations were used in the FEM simulation. The use of very accurate Young’s modulus from the field shear wave velocity test was the key to the successful simulation of the settlement under bridge pier foundations. 相似文献
6.
岩体工程计算分析中结构面刚度系数是至关重要的力学参数,计算分析的精度和可靠程度与这个参数密不可分,结构面刚度系数取值仍然是一个难点。岩体中应力波传播至结构面处将会发生反射和透射现象,利用应力波透射系数可反演结构面动态刚度系数。本文从细观力学角度运用颗粒离散元方法,开发分段线性接触模型及应力波吸收边界模型,开展宏观岩体中应力波传播的模拟,结合准静态压缩试验模拟,研究了较为平直的岩体结构面分别在不同正应力条件下的动、静态刚度系数的变化特征。模拟结果表明:(1)利用C++语言开发的分段线性接触模型很好地实现了结构面非线性变形特征的模拟;(2)基于颗粒离散元方法能够准确地反映岩体中应力波传播规律,应力波通过不同刚度结构面的透射系数与理论解一致;(3)在离散颗粒模型中加入黏滞吸收边界条件很好地实现了在有限尺寸模型中远场应力波传播模拟;(4)在岩体模型中结构面接触部位运用分段线性接触模型,通过模拟应力波传播与单轴压缩试验分别获得了一致性较好的结构面动、静态刚度系数,结构面动/静态刚度系数之比值约为1.0。本文对岩体中结构面刚度的测试和取值具有重要的指导意义。 相似文献
7.
裂隙岩体流固耦合问题是目前国内外研究热点之一,采用离散元软件UDEC对裂隙岩体发生节理剪胀的渗透性变化规律进行了模拟分析。基于现场调查的裂隙信息统计生成裂隙网络岩体模型。 通过固定垂直应力、不断增加应力比RS(RS=水平应力/垂直应力)使岩体出现剪胀,采用库伦滑移节理模式对岩体在剪胀过程中的渗透性变化情况进行模拟。结果发现:当应力比较小(RS3.1)时,节理水力隙宽、流速、渗透系数等参数都随着应力比的增加表现出明显的降低; 而当岩体出现剪胀现象之后(应力比大于3.1),发生剪切滑移和剪胀现象的节理控制着裂隙岩体的总体渗流行为,与不考虑节理剪胀的计算结果相比,岩体渗透能力出现了显著增长。这一结果表明,剪胀对裂隙岩体渗透性的影响是显著而不可忽视的。 相似文献
8.
This paper presents a numerical study of fracturing process induced by excavation around a gallery using an extended rigid block spring method (RBSM). The surrounding rock mass is characterized by an assembly of rigid blocks based on a degraded Voronoi diagram. The macroscopic mechanical behavior of rock is related to that of interfaces between blocks. The mechanical behavior of each interface is described by its elastic stiffness and failure criterion. The failure process of interface is controlled by both normal stress and shear stress. Both tensile and shear failures are considered. The macroscopic fracturing process is described by the coalescence of cracked interfaces. The rock structural anisotropy is taken into account through a spatial variation of elastic stiffness and failure strength of interfaces. A series of sensitivity studies are performed to investigate effects of gallery orientation, failure strength of interfaces and rock structural anisotropy on gallery deformation and fracturing. Numerical results are compared with in-situ observations in terms of fracture patterns. 相似文献
9.
Hossein Masoumi Kurt J. Douglas Adrian R. Russell 《Rock Mechanics and Rock Engineering》2016,49(1):47-62
A new constitutive model for intact rock is presented recognising that rock strength, stiffness and stress–strain behaviour are affected by the size of the rock being subjected to loading. The model is formulated using bounding surface plasticity theory. It is validated against a new and extensive set of unconfined compression and triaxial compression test results for Gosford sandstone. The samples tested had diameters ranging from 19 to 145 mm and length-to-diameter ratios of 2. The model captures the continuous nonlinear stress–strain behaviour from initial loading, through peak strength to large shear strains, including transition from brittle to ductile behaviour. The size dependency was accounted for through a unified size effect law applied to the unconfined compressive strength—a key model input parameter. The unconfined compressive strength increases with sample size before peaking and then decreasing with further increasing sample size. Inside the constitutive model two hardening laws act simultaneously, each driven by plastic shear strains. The elasticity is stress level dependent. Simple linear loading and bounding surfaces are adopted, defined using the Mohr–Coulomb criterion, along with a non-associated flow rule. The model simulates well the stress–strain behaviour of Gosford sandstone at confining pressures ranging from 0 to 30 MPa for the variety of sample sizes considered. 相似文献
10.
微震、工程爆破等低应力循环剪切荷载作用对节理岩体工程失稳破坏具有重要影响。为研究峰前循环剪切加卸载作用下岩石节理剪切力学特性,采用RDS-200型岩石节理剪切试验系统对人工劈裂黄砂岩节理进行了峰前循环剪切下的直剪试验。通过与未进行峰前循环剪切加卸载时岩石节理力学参数预测值对比,得到峰前循环剪切加卸载作用对峰前剪切刚度、峰值剪切强度、峰值剪切位移与残余剪切强度的影响。结果表明：（1）峰前循环剪切加卸载后,当法向应力为2 MPa时,岩石节理峰前剪切刚度增大,当法向应力为4～10 MPa时,岩石节理峰前剪切刚度在循环剪切应力幅值范围内增大,在超出循环剪切应力幅值时减小;（2）峰前循环剪切加卸载后,峰值剪切强度降低了10%～20%,降低百分比随法向应力增大整体呈对数函数增大;峰值剪切位移增加了2%～40%,增加百分比随法向应力增大整体呈对数函数减小;（3）峰前循环剪切加卸载后,岩石节理残余剪切强度无明显变化,峰值剪切强度与残余剪切强度差值减小,峰后剪切应力做功损失百分比降低。 相似文献
11.
Ausama A. Giwelli Koji Matsuki Kiyotoshi Sakaguchi Akihisa Kizaki 《国际地质力学数值与分析法杂志》2013,37(14):2186-2204
In the direct shear test (DST), an internal moment is distributed within the rock specimen by non‐coaxial shear loads applied to the specimen, which cause non‐uniform distributions of both the traction on the loading planes and the stress and deformation in the specimen. To examine the validity of the DST for a rock fracture and to clarify the effect of specimen height, both the stress and deformation in a fracture in the DST were analyzed for specimens with three different heights using a three‐dimensional finite element method with quadratic joint elements for a fracture model. The constitutive law of the fracture considers the dependence of the non‐linear behavior of closure on shear displacement and that of shear stiffness on normal stress and was implemented in simulation code to give a conceptional fracture with uniform mechanical properties to extract only the effect of non‐uniform traction on the stress and deformation in the fracture. The results showed that both normal and shear stresses are concentrated near the end edges of the fracture, and these stress concentrations decrease with a decrease in the specimen height according to the magnitude of the moment produced by the non‐coaxial shear loads. Furthermore, although closure is greater near the end edges of the fracture, where normal stress is concentrated, this concentration of closure is not so significant within the range of this study because of the non‐linear behavior of closure, that is, closure does not significantly increase with an increase in normal stress at large normal stresses. Copyright © 2012 John Wiley & Sons, Ltd. 相似文献
12.
卸荷过程岩体中弹性波波速变化分析 总被引：1，自引：0，他引：1
伴随岩体卸荷过程,岩体内部应力状态要进行调整,同时岩体内部几何结构也要发生变化。由于卸荷过程应力状态变化很复杂,文中利用卸载过程中岩体内部几何结构的变化来反映卸载过程,通过岩体几何结构对弹性波传播的影响来分析卸载过程的波速。为考虑弹性波作用下局部裂纹的相互作用,采用双裂纹模型近似分析。在双裂纹体系内部采用“相互作用”分析法,以部分考虑波在岩体内的多次散射;在双裂纹体系之间采用线性叠加分析法,以考虑岩体中缺陷影响的局部化。通过节理裂隙的张开程度和节理裂隙的张开率描述卸载过程对双裂纹体系的影响,由此,对比分析了开挖卸载过程中四种不同的玄武岩与主频25 kHz和主频1 kHz对应的弹性波波速的变化。结果表明,随着卸载过程的推移,主频25 kHz声波和主频1 kHz地震波对应的相对波速逐渐减小,但声波波速的减小幅度要比地震波减小的幅度小,声波波速可以降低到原来的80%,而地震波波速可以降低到原来的50%。结论对于水利工程、隧道工程等建基面的验收和评价有很好的指导意义 相似文献
13.
岩石节理剪切变形对岩体工程的安全性和稳定性具有重要影响。为研究常法向应力下岩石节理剪切变形本构关系,采用RDS-200型岩石直剪仪对非规则砂岩节理进行了不同法向应力下的直剪试验。根据岩石节理剪切应力?位移全程曲线形状特征,将其依次划分为峰前压密阶段、线性阶段、屈服阶段和峰后软化阶段;根据剪切应力在峰后软化阶段降低幅度和速率大小,将岩石节理剪切应力?位移曲线划分为3种类型：峰后平台型、峰后缓降型和峰后跌落型。基于岩石节理剪切应力?位移曲线各阶段剪切变形特征,采用分段函数建立了岩石节理剪切变形本构模型。与其他模型相比,新提出的岩石节理剪切变形本构模型对试验数据拟合精度更高,更好地描述了岩石节理剪切应力?位移全程曲线。另外,在通过岩石节理直剪试验由经验公式确定模型参数之后,所提出本构模型可在不同法向应力下实现对不同粗糙度岩石节理剪切应力?位移曲线的预测。研究结果对岩石节理剪切变形的数值模拟和工程估计具有一定的实用价值。 相似文献
14.
岩体的声学特性与应力状态和破坏程度密切相关,通过岩体声学特性的变化来分析岩体应力状态进而评价工程稳定性是一种行之有效的工程措施。针对砂岩开展了单轴压缩试验,并在加载过程中同步进行3个方向的声波测试,获得了砂岩加载过程中3个不同方向声波波速与应力的演化规律。试验结果表明：随着应力的增加,轴向波速逐渐增大,横向波速表现出先增后减的趋势。考虑到不同方向声波测试结果的差异性,采用含不同倾角裂隙的石膏试样进行声波试验。结果表明,当裂隙方向与声波传播方向一致时,波速最大,与声波传播方向垂直时,波速最小;此外,为分析岩样波速与应力状态的相关性,建立了波速与体应变的关系,结果表明,随着体应变的增加,平均波速逐渐增大,在体应变达到最大值附近时,平均波速达到最大值,在体应变下降阶段,波速开始下降;根据轴向波速与应力的变化规律,得到了应力与波速的指数函数拟合公式,据此可以通过现场测试获得的波速预测现场岩体的应力范围,进而评价工程岩体稳定性。 相似文献
15.
16.
为探究注采参数对松辽盆地干热岩物理力学及波动特征的影响,对不同注采参数下高温遇水冷却后花岗岩进行纵、横波波速测试试验和抗压强度试验。分别考虑注采参数（岩样温度、水温、高温遇水循环次数） 与岩样物理力学特征（外观形态、峰值强度、弹性模量、泊松比）、波动特征（纵、横波波速） 的关联性,建立不同注采参数下力学特征与波动特征拟合曲线,并研究搁置过程中不同岩样温度、不同水温条件下岩体物理力学及波动特征变化规律。研究发现：（1） 搁置初期,岩样温度越高,质量、纵、横波波速、弹性模量降幅越大;水温升高,质量、纵、横波波速、弹性模量降幅先增大后减小。（2） 对采热过程中岩体物理力学及波动特征影响由大到小的注采参数依次为靶区温度、注水循环次数、注水温度。提升岩样温度、增加注水循环次数,岩样力学与波动特征均逐渐下降,提高注水温度变化规律与其相反;经历600℃高温,岩样纵波波速、横波波速、峰值强度、弹性模量降幅分别达到53.44%、58.02%、66.56%、79.84%,高温遇水循环5 次
后降幅依次达到33.61%、33.63%、34.22%、56%。（3） 影响岩样力学与波动特征关联性的注采参数由大到小依次为岩样温度、高温遇水循环次数、水温。此研究能够为松辽盆地热采注采参数的选取提供一定参考。 相似文献
17.
岩石拉伸剪切破裂是一类特殊应力状态条件下的破裂形式,属于同时受垂直于破裂面的法向拉应力和平行于破裂面的剪应力作用的复合破裂模式。在研制的DSC-800电液伺服测控岩石拉伸剪切试验仪的基础上,进行了大量花岗闪长岩和砂岩的拉伸剪切试验,开展了配套的破裂断口三维激光扫描、扫描电子显微镜（SEM）、岩石物理力学性质试验、颗粒流离散元（PFC）数值模拟等相关试验,利用分形理论研究了岩石拉剪破裂面特征,研究了岩石拉剪-压剪全区破裂准则、剪切速率对岩石拉剪破裂强度的影响,采用颗粒流离散元研究了岩石拉剪破裂过程。研究结论如下:（1）岩石拉剪破裂面的宏观与微观分形维数即粗糙度随着拉应力的增加而增大;（2）岩石的微观断裂形式是拉伸破坏和剪切破坏的结合。当拉应力较小时,岩石的微观断裂形式主要表现为剪切破坏,并且随着拉应力的增加,岩石的拉伸破坏形式表现得更加明显;（3）岩石在拉伸剪切区的破裂拉应力与剪应力成线性负相关关系,在拉伸剪切应力区的岩石破裂线斜率比压缩剪切区大,岩石在拉伸剪切应力条件下比压缩剪切应力条件下容易破裂;（4）在岩石拉伸剪切条件下,剪切速率与剪切强度成非线性反相关关系,随着剪切速率的增加,岩石拉剪破裂面粗糙度增加;（5）建立了岩石拉伸剪切PFC数值试验模型,模拟了岩石拉伸剪切破裂过程中的力链演化以及剪切速率对拉剪破裂面粗糙度的影响,获得了与实验室试验一致的结果。 相似文献
18.
Euripides Papamichos 《国际地质力学数值与分析法杂志》2010,34(6):581-603
Borehole failure under anisotropic stresses in a sandstone is analyze numerically for various borehole sizes using a nonlinear elastic–plastic constitutive model for a Cosserat continuum. Borehole failure is identified as macroscopic failure of the borehole through the development of shear bands and breakouts. The results compare well both qualitatively and quantitatively with experimental results from polyaxial tests on Red Wildmoor sandstone. They show that the hole size effect of the borehole failure strength is independent of the far‐field stress anisotropy and follows a ? power law of the hole size. A similar scale effect equation with a ? power law is proposed for the scale effect of the maximum plastic shear strain at failure. This equation can be useful for better predicting hole‐size‐dependent failure with standard codes based on classical continua. The effect of stress anisotropy on the borehole failure stress is found to be independent of the hole size. The failure stress decreases linearly to 40% as the stress anisotropy increases. However, the maximum plastic shear strain at failure is stress anisotropy independent and therefore the critical plastic shear strain for failure is only hole‐size dependent. Copyright © 2009 John Wiley & Sons, Ltd. 相似文献
19.
Closed‐loop, servo‐controlled experiments were conducted to investigate the development of a shear band in Berea sandstone at various confining pressures. The tests were performed with the University of Minnesota Plane‐Strain Apparatus, which was designed to allow the shear band to develop in an unrestricted manner. Measured load and displacements provided estimates of the stress and deformation states whereby dilatancy and friction were evaluated prior to localization. Experiments were stopped at various stages of shear‐band development within the strain‐softening regime. The specimens displayed a progression of deformation from inception, where the shear band was characterized by a high density of intragranular microcracks and crushed grains, to the tip where the intragranular microcracks were significantly less dense and separated by intact grains. Decreased slip deformation towards the tip of the shear band indicated that localization developed and propagated in plane. Thin‐section microscopy showed porosity increase within the shear band was 3–4 grain diameters wide. Increased porosity did not extend beyond the tip of the shear band. A cohesive zone model of shear fracture, used to examine the stress field near the tip, showed similarities to principal compressive stress orientations interpreted from intragranular microcracks. Thus, propagation of the shear band could be associated with in‐plane mode II fracture. Copyright © 2006 John Wiley & Sons, Ltd. 相似文献
20.
借助损伤力学思想,基于统计强度理论,提出一种适用于深部工程破裂区破裂岩体的本构模型建立方法,并通过室内试验和数值试验进行了验证。将破裂岩体划分为无数微元立方体,微元立方体的强度与岩石破裂程度有关,且各立方体强度随机分布,故可用强度反映破裂岩体的破裂程度,据此提出一种破裂岩体本构模型建立方法。其中,根据岩石破裂面间的摩擦力做功等于材料破裂后释放的应变能,得到从力学角度定义的岩石破裂程度变量;另外,假定微元立方体强度分布服从Weibull分布,应力水平满足Hoek-Brown准则。利用泥质砂岩破裂岩体典型三轴试验结果,建立泥质砂岩破裂岩体本构模型,并进行了验证,结果表明模型计算曲线与试验曲线吻合度较好。利用离散元软件PFC进行了补充数值试验验证研究,证明了泥质砂岩破裂岩体理论模型的良好计算效果,进而证明提出的本构模型建立方法的可行性。 相似文献