首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献，搜索用时 31 毫秒
1.
The Kızılcahamam geothermal field is emplaced in Tertiary-aged volcanic units 70 km NW of Ankara (Turkey). Data for this low-temperature (74–86°C) geothermal field regarding the fracture zone system were obtained from surface manifestations (hot springs, alteration zones), five exploration wells (MTA-2, -3, -4, -5, -6) and two production wells (KHD-1, MTA-1). The Kızılcahamam reservoir developed along the Kızılcahamam fault zone and so the production wells (180–1556 m) effect each other due to their limited separation. Meteoric water enters from a recharge area NE of Kızılcahamam, circulates and gains heat through the fault zone, and discharges to the surface.Detailed petrographical studies have been carried out with samples taken from surface rocks, cores, and cuttings from three wells (KHD-1, MTA-2, -3). X-ray diffraction techniques were also used in the present study. Kaolinite and montmorillonite zones were identified at outcrop samples. Chloritization, clay mineralization, sericitization and carbonization were determined in the ground mass of samples from wells. The observed alteration mineral assemblages indicate that Kızılcahamam geothermal system has been cooling since the alteration minerals formed.The exploration well MTA-3 seems to be more suitable for a reinjection well than the other wells (MTA-2, -6), even if the cost of surface piping to transport the waste water to MTA-3 is higher than to another well (MTA-6).  相似文献   

2.
Hydrothermal alteration zones have been investigated by X-ray diffraction, mineralogical–petrographical techniques, and geochemical analysis. Examination of cores and cuttings from two drill sites, obtained from a depth of about 814–1020 m, show that the hydrothermal minerals occuring in the rock include: K-feldspar, albite, chlorite, alunite, kaolinite, smectite, illite, and opaque minerals.In the studied area, silicified, smectite, illite, alunite, and opal zones have been recognized. These alteration mineral assemblages indicate that there are geothermal fluids, which have temperatures of 150–220°C in the reservoir.The distribution of the hydrothermal minerals shows changes in the chemical composition of the hydrothermal fluid, which are probably due not only to interaction with host rock, but also to dilution of the Na–K–Cl-rich hydrothermal fluid of the deep reservoir by cold sea water at shallow levels. Geochemical analyses of the solid and liquid phases indicate that the hydrothermal fluids of the Tuzla geothermal system are in equilibrium with alteration products.The tectonic structure of the studied area is caused by NW–SE and NE–SW directional forces. The volcanic rocks where hydrothermal zones are observed in the studied area are of Lower–Middle Miocene age comprise latite, andesite, dacite, rhyolite-type lavas, tuff, and ignimbrites.  相似文献   

3.
Study of the opaque minerals from well No. 7, Krafla, indicates two mineral assemblages: (1) hydrothermally altered igneous minerals and (2) secondary minerals that have precipitated from the geothermal fluid at depths down to 2140 m, and at temperatures up to more than 340°C. Chief amongst the chemically precipitated minerals are pyrite, pyrrhotite and goethite, which is described here for the first time in an Icelandic geothermal drill hole.The geothermal system at Krafla has been periodically disturbed by the influx of volcanic emanations; this article attempts to interpret, by use of thermochemical calculations, the processes affecting the precipitated mineral assemblage.  相似文献   

4.
Thermal waters hosted by Menderes metamorphic rocks emerge along fault lineaments in the Simav geothermal area. Thermal springs and drilled wells are located in the Eynal, Çitgöl and Na a locations, which are part of the Simav geothermal field. Studies were carried out to obtain the main chemical and physical characteristics of thermal waters. These waters are used for heating of residences and greenhouses and for balneological purposes. Bottom temperatures of the drilled wells reach 163°C with total dissolved solids around 2225 mg/kg. Surface temperatures of thermal springs vary between 51°C and 90°C. All the thermal waters belong to Na–HCO3–SO4 facies. The cold groundwaters are Ca–Mg–HCO3 type. Dissolution of host rock and ion-exchange reactions in the reservoir of the geothermal system shift the Ca–Mg–HCO3 type cold groundwaters to the Na–HCO3–SO4 type thermal waters. Thermal waters are oversaturated at discharge temperatures for aragonite, calcite, quartz, chalcedony, magnesite and dolomite minerals giving rise to a carbonate-rich scale. Gypsum and anhydrite minerals are undersaturated with all of the thermal waters. Boiling during ascent of the thermal fluids produces steam and liquid waters resulting in an increase of the concentrations of the constituents in discharge waters. Steam fraction, y, of the thermal waters of which temperatures are above 100°C is between 0.075 and 0.119. Reservoir pH is much lower than pH measured in the liquid phase separated at atmospheric conditions, since the latter experienced heavy loss of acid gases, mainly CO2. Assessment of the various empirical chemical geothermometers and geochemical modelling suggest that reservoir temperatures vary between 175°C and 200°C.  相似文献   

5.
In this study, representative samples from thermal wells and springs were chemically analyzed and geothermometers were used to calculate the deep temperatures of geothermal reservoirs on the basis of water–mineral equilibrium. In some cases, however, the chemical components are not in equilibrium with the minerals in the reservoir. Therefore, log(Q/K) diagrams are used to study the chemical equilibrium for the minerals that are likely to participate. The Na–K–Mg triangular diagram is also applied to evaluate the equilibrium of water with reservoir rocks. Standard curves at the reference temperatures are prepared to reveal which type of silica geothermometer is appropriate for the specified condition. This study shows that water samples from geothermal wells W9 and W12 are in equilibrium with the selective minerals, and chalcedony may control the fluid–silica equilibrium. It is estimated that there is an exploitable low-temperature reservoir with possible temperatures of 80–90°C in the Guanzhong basin.  相似文献   

6.
The Campi Flegrei (Naples, Campanian Plain, southern Italy) geothermal system is hosted by Quaternary volcanic rocks erupted before, during and after the formation of the caldera that represents one of the major structural features in the Neapolitan area. The volcanic products rest on a Mesozoic carbonate basement, cropping out north, east and south of the area. Chemical (major, minor and trace elements) and stable isotope (C, H, O) analyses were conducted on drill-core samples recovered from geothermal wells MF-1, MF-5, SV-1 and SV-3, at depths of ˜ 1100 to 2900 m. The study was complemented by petrographic and SEM examination of thin sections. The water which feeds the system is both marine and meteoric in origin. Mineral zonation typical of a high-temperature geothermal system exists in all the geothermal wells; measured temperatures in wells are as high as ˜ 400 °C. The chemical composition of the waters suggests the existence of two reservoirs: a shallow reservoir (depth < 2000 m) fed by seawater that boiled at 320 °C and became progressively diluted by steam-heated local meteoric water during its ascent; and a deeper reservoir (depth > 2000 m) of hypersaline water. The drill-cores are mainly hydrothermally altered volcanics of trachy-latitic affinity, but some altered pelites and limestones are also present. Published Na, Mg and K concentrations of selected geothermal waters indicate that the hydrothermal fluids are in equilibrium with their host rocks, with respect to K-feldspar, albite, sericite and chlorite. The measured δ18O(SMOW) values of rocks range from +4.3 to + 16.5%. The measured δD(SMOW) values range from − 79 to − 46%. The calculated isotopic composition of the fluids at equilibrium with the samples vary from + 1 to + 8.3%. δ18O and from − 52 to + 1%. δD. The estimated isotopic composition of the waters at equilibrium with the studied samples confirmed the existence of two distinct fluid types circulating in the geothermal system. The shallower has a marine water signature, while the deeper water has a signature consistent both with magmatic and meteoric origins. In the latter case, the recharge of this aquifer likely occurs at the outcrop of the Mesozoic Limestones surrounding the Campanian Plain; after infiltration, the water percolates through evaporitic layers, becoming hypersaline and D-depleted.  相似文献   

7.
Five geothermal waters from the Mons area (southern Belgium) have been studied: one natural hot spring at Stambruges, one stagnant warm water from the “inclined tunnels” at Baudour, and three thermal waters from the drillholes at St. Ghislain, Ghlin and Douvrain, originating from the carbonate/anhydrite-bearing Visean strata, at depths of ca. 2600, 1550 and 1300 m, respectively.Multielement chemical analysis of the filtered water and its suspended matter > 0.4 μm) was carried out by instrumental neutron activation.Temperature in depth, calculated using the silica (chalcedony) chemical geothermometer, ranged from 75 to 88°C, in good agreement with experimentally determined values. Na/K and Na/K/Ca geothermometers yieilded erratic results, as expected from the geological environment in the aquifer.From the analytical data it can be calculated that the thermal waters of St. Ghislain, Ghlin and Douvrain are not only saturated with respect to chalcedony, but also to anhydrite, calcite, fluorite, barite, strontianite, and possibly zinc silicate, iron (III) hydroxide or siderite, albite, microcline, gibbsite and kaolinite. They are oversaturated with respect to muscovite. Data are also presented for the other thermal waters, and a cold spring water (Claire Fontaine, Stambruges).The similar trace-element composition of the thermal waters can be explained by percolation of the water in the same distant recharge zone, from where it descends, becomes heated at depth and rises along collapse breccia, and locally (Baudour, Stambruges) along fissures. The uptake of higher amounts of Ca, Mg, Sr and sulfate in St. Ghislain and Ghlin, as compared to Douvrain and Baudour is correlated with the boundary between the “non-dissolved” and “dissolved” evaporitic zones. This boundary is situated between St. Ghislain and Douvrain, and is roughly parallel with the direction of the groundwater flow (WNW).  相似文献   

8.
The carbon isotopic composition of diagenetic dolomite and calcite in some sediments of the Gulf of Mexico varies between “normal-marine” (δ13C ca. 0‰) and −14.6‰ which suggests that biogenic CO2 contributed to the carbonate formation. The δ13O values of dolomite and coexisting calcite are very similar but variable down-core.Dolomite and calcite precipitated early from pore water where SO42− was not reduced. However, during (and after?) SO42− reduction dolomite and calcite still formed and there are at least two generations of carbonate minerals present.  相似文献   

9.
Abstract Compositional variation of silicates (plagioclase, K-feldspar, epidote, titanite, garnet, white mica, biotite, chlorite), ilmenite, carbonates (calcite, ankerite) and apatite, in quartzofeldspathic lithologies of the Alpine Schist, New Zealand, is discussed in terms of increasing metamorphic grade and possible isograd-producing reactions. The mineral data, in conjunction with geological considerations, are used to determine polychronous P-T arrays of an early high P/T event (c. 16°C/kb; 5°C/km) overprinted by a lower P/T event (c. 50°C/kb; 15°C/km) that provides an estimation of Mesozoic and Cenozoic exhumation of schist of 11 to 13 km and 19 to 22 km respectively. The effects of possible shear heating and recrystallization to form K-feldspar zone schist near the Alpine Fault is consistent with movement along a mid to lower crustal detachment surface during Cenozoic shortening, and near isothermal exhumation of the schists to form the Southern Alps.  相似文献   

10.
UPb geochronology provides an absolute time framework for the evolution of the Sigma gold deposit and surrounding rocks at Val d'Or, southern Abitibi subprovince. The Bourlamaque batholith, the largest pluton in the area, gives a 2699.8 ± 1.0 Ma UPb zircon age. This pluton cuts the Val d'Or Formation which hosts the mineralization. A UPb zircon age of 2704.9 ± 1.1 Ma on a felsic volcanic rock, the Colombière “rhyolite”, 13 km east of the mine dates that formation. The gold-bearing quartz vein system at Sigma is hosted by andesites and two generations of porphyry intrusions, all metamorphosed to the greenschist facies. The oldest porphyry (“porphyritic diorite”) shows the same deformation as the volcanic rocks, and has a 2703.7 ± 2.5 Ma UPb zircon age. The porphyritic diorite and volcanic rocks are cut by feldspar-porphyry dykes which post-date regional folding and have a 2694.0 ± 2.2 Ma UPb zircon age.Regional greenschist metamorphism has been dated directly, with a UPb date of 2684 ± 7 Ma on rutile in the Colombière “rhyolite”. The mineralization and hydrothermal alteration in the mine are superimposed on the metamorphic minerals. Hydrothermal rutile, from an alteration halo around the veins in andesite, has a 2599 ± 9 Ma UPb age. Textural evidence clearly indicates that the wall-rock alteration and vein filling are contemporaneous, and hence the vein system and gold mineralization appear to have developed at least 80 m.y. after the formation and metamorphism of host greenstones.  相似文献   

11.
Philippine geothermal systems occur in the vicinity of large Holocene calc-alkaline volcanic complexes. Wells drilled in these areas encountered multiple intrusions; the latest dikes are the subsurface manifestations of the youngest heat source. Commonly, at least two hydrothermal regimes are juxtaposed in a single area, with the latest being in equilibrium with the present temperature and chemical regime.Alteration by neutral-pH water is pervasive and abundant. A contact-metamorphic aureole also occurs near intrusives. Alteration due to acid-sulfate fluids is generally confined to permeable structures. Neutral-pH alteration is divided into four zones on the basis of key clay minerals, and two subzones are defined by calc-silicates. These are the smectite (ambient to 180°C), transition (180–230°C), illite (230–320°C) and biotite (270–340°C) zones. Subzones are defined by epidote (250–340°C) and amphibole (280–340°C). The four main zones of acid alteration are: kaolinite (ambient to 120°C), dickite ± kaolinite (120–200°C), dickite ± pyrophyllite (200–250°C), and pyrophyllite ± illite (230–320°C). Where relict high-temperature alteration reaches the surface, the area being drilled is usually the outflow zone of the present system.These hydrothermal mineral assemblages are used: (1) as geothermometers; (2) to assist in determining the depth at which the production casing will be set during drilling; (3) to estimate fluid pH and other chemical parameters; (4) to predict possible corrosion and scaling tendencies of the fluids; (5) as a measure of permeability and possible cold water influx into wells; (6) as a guide to field hydrology; and (7) to estimate roughly the thickness of the eroded overburden.  相似文献   

12.
The deep well MV5A, drilled in the western part of the Larderello geothermal field, crossed a 20-cm-thick hydraulic fracture breccia unit at a depth of 1090 m below ground level (b.g.l.). This breccia occurs in a fine-grained Triassic metasandstone and consists of angular to subangular clasts of up to some centimeters in size. Pervasive alteration has affected the breccia clasts and wall rock around the breccia, with the formation of Mg–Fe chlorite. After such alteration, hydrothermal circulation caused the precipitation of two generations of calcite cement. Then, ankerite partially replaced these two calcite generations. Ankerite also precipitated in late veinlets with chlorite. Late hydrothermal activity led to the crystallization of albite, quartz and finally, anhydrite. The calcite contains vapor-rich inclusions and two populations of liquid-rich (L1 and L2) inclusions. L1 inclusions are characterized by homogenization temperatures between 304 and 361°C and salinities from 7.4 to 11.6 wt.% NaCl equivalent; L2 inclusions revealed homogenization temperatures in the range of 189–245°C and salinities from 2.6 to 6.3 wt.% NaCl equivalent. The fluids contained in L2 inclusions were probably trapped coevally with some vapor-rich inclusions under boiling conditions after the L1 inclusions formed. Some of the abundant vapor-rich inclusions in calcite may also represent early, low-temperature inclusions affected by decrepitation and/or stretching and/or leaking during L1 trapping. The liquid-rich (L) inclusions trapped at later stages in ankerite, albite and anhydrite display, respectively, homogenization temperature ranges of 189–198°C, 132–145°C, and 139–171°C, and salinities ranging from 1.6 to 1.7 wt.% NaCl equivalent, 1.4 to 2.1 wt.% NaCl equivalent and 3.7 to 6.2 wt.% NaCl equivalent. The inclusions studied record the evolution, over time, of the fluids flowing in the breccia level: L1 inclusions capture high-temperature fluid (about 300 to 350°C) of high salinity (around 10 wt.% NaCl equivalent) at above-hydrostatic pressures (up to about 150 bar). The L2 inclusions in calcite and liquid-rich inclusions in ankerite and albite represent subsequent hydrothermal fluid evolution toward lower temperatures (about 250 to 130°C), pressures (45 to a few bar) and salinities (6.3 to 1.4 wt.% NaCl equivalent). During this stage, boiling processes and infiltration of meteoric waters probably occurred. Finally, moderately saline fluids (around 5 wt.% NaCl equivalent) at a temperature (about 160°C) close to that of present-day in-hole measurements was trapped in the anhydrite inclusions. The liquids trapped in liquid-rich inclusions circulated at 41,000 years (maximum age of calcite) or later. This age represents an upper limit for the development of vapor-dominated condition, in this part of the geothermal system. The fluids circulating at the breccia level were probably meteoric and/or connate waters. These fluids may have interacted with the anhydrite and carbonate bearing formations present in the Larderello area. The occurrence of the hot and saline fluids, trapped in L1 inclusions at above-hydrostatic pressure, suggests that similar fluids but with higher pressure (≥167 bar) and temperature (≥360°C) may have been responsible for rock fracturing.  相似文献   

13.
ABSTRACT

Multivariate statistical analysis and inverse geochemical modelling techniques were employed to deduce the mechanism of groundwater evolution in the hard-rock terrain of Telangana, South India. Q-mode hierarchical cluster analysis (HCA) and principal component analysis (PCA) were used to extract the hydrogeochemical characteristics and classify the groundwater samples into three principal groups. Use of thermodynamic stability diagrams and inverse geochemical modelling in PHREEQC identified the chemical reactions controlling hydrogeochemistry of each of the groups obtained from statistical analysis. The model output showed that a few phases are governing the water chemistry in this area and the geochemical reactions responsible for evolution of groundwater chemistry along the flow path are (i) dissolution of evaporite minerals (dolomite, halite); (ii) dissolution of primary silicate minerals (albite, anorthite, K-feldspar, biotite); (iii) precipitation of secondary silicate minerals (kaolinite, quartz, gibbsite, Ca-montmorillonite) along with anhydrite and calcite; and (iv) reverse ion exchange processes.  相似文献   

14.
Previously unrecognized pulses of rhyolite volcanism occurred in the Salton Trough between 420 ± 8 ka and 479 ± 38 ka (2σ), based on high-spatial resolution U–Pb zircon geochronology. Presently, these rhyolite lavas, tuffs and shallow subvolcanic sills are buried to depths between ~ 1.6 and 2.7 km at ambient temperatures between 200 and 300 °C, and are overprinted by propylitic to potassic hydrothermal alteration mineral assemblages consisting of finely intergrown quartz, K-feldspar, chlorite, epidote, and minor pyrite. Alteration resistant geochemical indicators (whole-rock Nd-isotopes, zircon oxygen-isotopes) reveal that these rhyolites are derived from remelting of MORB-type crust that was chilled and hydrothermally altered by deep-circulating hydrothermal waters. U–Pb zircon dating confirms the presence of Bishop Tuff in well State 2-14 at ~ 1.7 km depth, approximately 5 km NE of the geothermal wells that penetrated the buried rhyolites. These results indicate accelerated subsidence towards the center of the Salton Trough, increasing from 2.2 mm/a to 3.8 mm/a. Based on these results, the present-day Salton Sea geothermal field is identified as a focus zone of episodic rhyolitic volcanism, intense heat flow and metamorphism that predates present-day geothermal activity and Holocene volcanism by at least ~ 400 ka.  相似文献   

15.
Detailed geochemistry supported by geologic mapping has been used to investigate Sulphur Springs, an acid-sulfate hot spring system that issues from the western flank of the resurgent dome inside Valles Caldera. The most intense activity occurs at the intersection of faults offsetting caldera-fill deposits and post-caldera rhyolites. Three geothermal wells in the area have encountered pressures <1 MPa and temperatures of 200°C at depths of 600 to 1000 m. Hot spring and fumarole fluids may discharge at boiling temperatures with pH 1.0 and SO4 8000 mg/l. These conditions cause argillic alterations throughout a large area.Non-condensible gases consist of roughly 99% CO2 with minor amounts of H2S, H2, and CH4. Empirical gas geothermometry suggests a deep reservoir temperature of 215 to 280°C. Comparison of 13C and 18O between CaCO3 from well cuttings and CO2 from fumarole steam indicates a fractionation temperature between 200 and 300°C by decarbonation of hydrothermally altered Paleozoic limestone and vein calcite in the reservoir rocks. Tritium concentrations obtained from steam condensed in a mudpot and deep reservoir fluids (Baca #13, 278°C) are 2.1 and 1.0 T.U. respectively, suggesting the steam originates from a reservoir whose water is mostly >50 yrs old. Deuterium contents of fumarole steam, deep reservoir fluid, and local meteoric water are practically identical even though 18O contents range through 4‰, thus, precipitation on the resurgent dome of the caldera could recharge the hydrothermal system by slow percolation. From analysis of D and 18O values between fumarol steam and deep reservoir fluid, steam reaches the surface either (1) by vaporizing relatively shallow groundwater at 200°C or (2) by means of a two-stage boiling process through an intermediate level reservoir at roughly 200°C.Although many characteristics of known vapor-dominated geothermal systems are found at Sulphur Springs, fundamental differences exist in temperature and pressure of our postulated vapor-zone. We propose that the reservoir beneath Sulphur Springs is too small or too poorly confined to sustain a “true” vapor-dominated system and that the Sulphur Springs system may be a “dying” vapor-dominated system that has practically boiled itself dry.  相似文献   

16.
The “fluid-flow tomography”, an advanced technique for geoelectrical survey based on the conventional mise-à-la-masse measurement, has been developed by Exploration Geophysics Laboratory at the Kyushu University. This technique is proposed to monitor fluid-flow behavior during water injection and production in a geothermal field. However data processing of this technique is very costly. In this light, this paper will discuss the solution to cost reduction by applying a neural network in the data processing. A case study in the Takigami geothermal field in Japan will be used to illustrate this. The achieved neural network in this case study is three-layered and feed-forward. The most successful learning algorithm in this network is the Resilient Propagation (RPROP). Consequently, the study advances the pragmatism of the “fluid-flow tomography” technique which can be widely used for geothermal fields. Accuracy of the solution is then verified by using root mean square (RMS) misfit error as an indicator.  相似文献   

17.
Dissolution of igneous feldspar and the formation and occurrence of secondary feldspar in tholeiitic basalts from the Hengill volcanic centre, in SW Iceland was studied by microprobe analysis of cuttings from two ca. 2000 m deep geothermal wells. Well NG-7 in Nesjavellir represents a geothermal system in a rift zone where the intensity of young, insignificantly altered intrusions increases with depth. Well KhG-1 in Kolviðarhóll represents the margin of a rift zone where the intensity of intrusives is lower and the intensity of alteration higher. This marginal well represents altered basaltic crust in an early retrograde state. The secondary plagioclase in both wells is mainly oligoclase, occurring in association with K-feldspar and chlorite±actinolite. The texture of this assemblage depends on the lithology and intensity of alteration. In Nesjavellir (NG-7) the composition of secondary albite-oligoclase is correlated with the host-rock composition. This connection is not apparent in more intensely altered samples from Kolviðarhóll (KhG-1). The influence of temperature on composition of secondary Na-feldspar is unclear in both wells although Ca is expected to increase with temperature. Any temperature dependence may be suppressed by the influence of rock composition in Nesjavellir and by retrograde conditions at Kolviðarhóll. The absence of clear compositional gradients between igneous plagioclase and secondary feldspar and between Na-feldspar and K-feldspar suggests that secondary feldspars formed by dissolution precipitation reactions.  相似文献   

18.
Coexisting fine-grained (0.1–20 μm) authigenic silicate minerals separated from altered tuffs in Miocene and Plio-Pleistocene lacustrine deposits were characterized petrographically and using X-ray powder diffraction. The authigenic minerals are dominated by clinoptilolite, erionite, phillipsite, K-feldspar, silica, calcite, smectite, and randomly interstratified illite/smectite. Minor accessories of opal-CT, cristobalite, and barite are present with the major alteration minerals. Authigenic minerals from altered tuffs were dated using the K/Ar method to evaluate the utility of these minerals for determining the time of alteration in low-temperature diagenetic environments. The eruption ages of some of these zeolite-rich tuffs were determined using the 40Ar/39Ar method on single sanidine and plagioclase minerals. The K/Ar isotopic ages of the fine-grained K-feldspar show minimal variation compared with results from the clinoptilolite separates. The isotopic ages from the authigenic K-feldspar (15-13.8 Ma) and some of the zeolites (16.-6.7 Ma) are similar to the eruption ages of the tuffs and indicate early alteration. Despite their open-framework structure, zeolites apparently can retain part or all of their radiogenic argon under favorable conditions (e.g., saturated environment). How much of the radiogenic argon is retained is estimated from the isotopic ages of other coexisting secondary minerals that are commonly dated by the K/Ar method. Although zeolite isotopic ages should be interpreted with caution, they may be useful to constrain temporal relations of low-temperature diagenetic processes when used in conjunction with other dateable minerals.  相似文献   

19.
Lower crustal high grade metamorphic rocks have been successively found at Pamirs nearby the western Himalayan syntaxis, Namjagbarwa and Dinggye nearby the eastern Himalayan syntaxis and the central segment of the Himalayan Orogenic Belt, respec-tively[1―4]. In particular, some researchers deduced that there were probably eclogites at some locations[5]. Moreover, some geochronological data of these lower crustal granulites also have been accumulated. For example, the high-pressure granulit…  相似文献   

20.
The different basalt types related to rift structure development have been investigated, starting from the pre-rift stage in the northern Ethiopian rift and its eastern escarpment and plateau.The basic volcanic rocks are represented mainly by transitional basalts, both in the pre-rift (plateau) and rift (escarpment and rift floor) stages. A striking feature is that although the plateau basalts show clear tholeiitic affinity and the rift basalts reveal a somewhat pronounced “alkaline” character, the REE and LILE element abundances, however, progressively decrease from the “tholeiitic” basalts of the plateau to the “alkaline” basalts of the rift.All data support the view that such contrasting features may be attributed to a continuous depletion of hygromagmatophile (REE, LILE) elements in the mantle source material, related to the large volumes of magmas produced in the early phase of rift structure development. The transition from “tholeiitic” (plateau) to “alkaline” (rift) transitional basalts is related to decreasing intensity of extensional movements.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号