共查询到20条相似文献，搜索用时 15 毫秒
1.
围绕堆石料单粒强度尺寸效应的颗粒流模拟方法展开研究。首先,基于FISH二次开发建立了堆石料的随机不规则单粒模型,充分考虑堆石料的形状特征和破碎现象;然后,建立了堆石料单粒强度尺寸效应的等效模拟方法,以单粒强度随其粒径的变化规律为基础,推导了堆石料模型中细观黏结强度与堆石料等效粒径的负指数经验公式;其次,基于建立的数值模型对堆石料的室内单粒压缩试验进行仿真模拟,验证数值模型的正确性和合理性,并对较大粒径堆石料的单粒强度进行模拟预测,突出数值试验的优势;最后,基于建立的数值模型对相同粒径不同形状特征堆石料的单粒强度分布特征进行模拟研究。研究结果表明：（1）堆石料内部缺陷含量和尺寸随粒径增加对其单粒强度所产生的尺寸效应,可通过堆石料模型中细观强度参数随粒径折减进行等效模拟;（2）形状特征对堆石料的破裂机制具有重要影响,方形颗粒为压剪破裂,单粒强度较高,而随机不规则颗粒和圆形颗粒为拉剪或劈裂,单粒强度相对较低;（3）拉剪或劈裂条件下,堆石料形状越不规则,其单粒强度的离散程度越高,反之则离散程度越低。相关研究成果可为进一步研究荷载作用下堆石体内各粒径段堆石料的破碎量奠定基础,从而更加真实地反映堆石体的级配演化规律。 相似文献
2.
Empirical evidence has shown that particle breakage affects the mechanical behaviour of granular materials. The source of this mechanism takes place at the particle scale, and the main consequence on the macromechanical behaviour is increasing compressibility. Due to the inverse correlation between particle size and particle crushing strength, coarse rockfill materials are particularly vulnerable to mechanical degradation due to particle breakage. However, such coarse materials do not fit in standard laboratory devices, and the alternative of large sample testing is usually unavailable or too expensive. Alternatively, recent works have proposed multi-scale approaches using the discrete element method (DEM) to carry out numerical testing of coarse crushable materials, although few studies have focused on size effects. This article presents the application of a DEM bonded-cell model to study particle size-strength correlation on angular rock aggregates. Each particle is modelled by a cluster of perfectly rigid polyhedral cells with Mohr–Coulomb contact law. Constant cell density within particles implies that the presence of potential fragmentation planes increases with size. Therefore, particle strength decreases with size. A comprehensive sensitivity analysis was carried out through 1477 particle crushing simulations in a given particle size. Based on published experimental data on calcareous rock aggregates, part of the simulations were used for calibration, and 97 additional simulations of a coarser size fraction were performed for validation. The results show a good agreement with the empirical data in terms of size effect and data scatter through Weibull statistics. 相似文献
3.
高土石坝中,堆石体颗粒破碎是导致坝体变形的主要因素之一。但是由于原型坝料的颗粒尺寸较大,其破碎程度难以直接通过室内试验度量,因此通常要将原型级配缩尺为60 mm以下的小粒径级配堆石料,然后才能进行室内试验。而由于原型和试验级配差异较大,导致试验测得的参数往往和原型坝料实际参数有较大差异,因而影响了原型坝料力学特性的深入研究。这里提出了一种新的实时预测原型坝料破碎的方法。首先在颗粒尺度上,基于单粒强度的Weibull分布理论和颗粒分形破碎理论,阐述了原型堆石料级配演化的推求过程;然后通过单粒强度试验测得了相关参数,并与三轴试验测得的试样级配曲线对比,验证了参数选取的合理性;之后分析了颗粒强度离散程度对于原型坝料级配曲线形状的影响;最后,讨论了加载过程中原型级配和试验级配堆石体的相对破碎参量和受力状态的关系。 相似文献
4.
压力作用下颗粒发生破碎是引起砂土力学特性变化的重要因素之一, 对于钙质砂这种易破碎的材料更是如此。为进一步弄清颗粒破碎对钙质砂的应力-应变强度影响, 本文对钙质砂进行三轴固结排水剪切试验得到应力-应变曲线, 并筛分得到三轴试验前后钙质砂颗分曲线。通过引入Hardin定义的颗粒相对破碎率Br, 分析了相对密度、围压与颗粒破碎的关系及颗粒破碎对钙质砂应力-应变和抗剪强度的影响。结果表明:随围压的增大颗粒破碎增量逐渐减小, 直到破碎达到一个上限值, 此时围压和相对密度对颗粒破碎影响很小; 颗粒间的滑动标志着应力达到极限状态, 而颗粒破碎会阻碍应力达到极限状态, 在本实验中, 低围压时颗粒破碎少, 颗粒相对运动形式为滑移, 使应力-应变曲线为软化型, 高围压下颗粒破碎严重, 颗粒破碎在剪切过程中始终发生, 使应力-应变曲线呈应变硬化型; 颗粒破碎使体变从剪胀逐渐发展到剪缩, 且破碎越严重剪缩越严重; 在低围压下钙质砂强度主要由剪胀和咬合提供, 高围压下颗粒破碎严重, 剪胀消失, 咬合减小, 使峰值摩擦角减小, 抗剪强度降低。 相似文献
5.
通过6种典型堆石块体的形状近似,分别采用两种接触本构模型建立了多块体形状堆石体离散元数值模型,研究堆石体在碾压荷载作用下的颗粒破碎过程,建立颗粒破碎的量化计算方法,分析碾压前、后堆石级配曲线的变化,讨论接触本构模型和颗粒形状对块体破碎的影响。模拟结果显示,碾压荷载下堆石颗粒以张拉破碎为主,随着碾压遍数的增加,局部开始出现剪切破碎;提出的颗粒破碎量化计算方法,在大粒径范围对粒径变化幅度预测偏大,但级配曲线整体趋势与实测结果比较吻合;相比较于接触连接模型,平行连接模型与现场碾压试验结果更接近。6种块体形状的数值结果显示,随着形状系数的增加,在其他条件不变的情况下颗粒破碎率逐渐降低,其中类长方形块体在碾压荷载作用下颗粒破碎最明显。相比较于纯圆颗粒或者单一非圆颗粒,采用的6种颗粒形状建立的堆石体振动碾压离散元模型,更接近现场实际情况。 相似文献
6.
固体颗粒破碎强度的尺寸效应是一种普遍存在的现象,冰块、岩石颗粒、陶瓷和混凝土块等的破碎强度都表现出随颗粒直径增加而减小的现象,分形模型为解释固体颗粒破碎强度的尺寸效应提供了可行的方法。本文采用Steacy和Sammis分形模型模拟了岩石颗粒压碎特征,分析岩石颗粒破碎后的颗粒分布规律,给出颗粒破碎分维的确定方法,建立颗粒压碎强度与粒径的理论关系,颗粒破碎强度与颗粒粒径的关系用分维D表示为fdD-3。已有的颗粒破碎分布的数据表明,岩石颗粒破碎的分维大约为2.50～2.60,颗粒破碎强度符合用分维表示的尺寸效应。 相似文献
7.
Strength and deformation behaviors of rockfill materials,key factors for determining the stability of dams,pertain strongly to the grain crushing characteristics.In this study,single-particle crushing tests were carried out on rockfill materials with nominal particle diameters of 2.5 mm,5 mm and 10 mm to investigate the particle size effect on the single-particle strength and the relationship between the characteristic stress and probability of non-failure.Test data were found to be described by the Weibull distribution with the Weibull modulus of 3.24.Assemblies with uniform nominal grains were then subjected to one-dimensional compression tests at eight levels of vertical stress with a maximum of 100 MPa.The yield stress in one-dimensional compression tests increased with decreasing the particle size,which could be estimated from the single-particle crushing tests.The void ratio-vertical stress curve could be predicted by an exponential function.The particle size distribution curve increased obviously with applied stresses less than 16 MPa and gradually reached the ultimate fractal grading.The relative breakage index became constant with stress up to 64 MPa and was obtained from the ultimate grading at the fractal dimension(a?2:7).A hyperbolical function was also found useful for describing the relationship between the relative breakage index and input work during one-dimensional compression tests. 相似文献
8.
筑坝堆石料由于尺寸较大,必须对其按一定比例缩尺后才能用来开展室内三轴试验。但缩尺前后颗粒形状难免会有差异,如何评价颗粒形状变化对堆石料变形特性的影响是十分重要的。引入了高精度的三维激光扫描技术对紫坪铺面板坝筑坝堆石料2.5～5、5～10、10～20 mm以及20～40 mm 4个粒径组的颗粒进行了空间形状分析,在此基础上进一步开展了单一粒组的三轴试验,研究了4个粒组的颗粒形状指标与颗粒破碎率的相关性。试验表明,紫坪铺堆石料颗粒破碎率随着其平均球度的增加而减小,并且呈近似半对数线性关系;随着围压的增加,颗粒形状对颗粒破碎的影响逐渐减弱,颗粒强度的影响逐渐增大。紫坪铺堆石料的颗粒强度随着颗粒尺寸的增加逐渐减小,但其破碎率反而随着颗粒尺寸的增加而逐渐减小,主要是因为试验所采用的紫坪铺堆石料颗粒尺寸越小时,其形状越不规则。因此,研究缩尺效应对颗粒破碎率的影响时,要同时考虑颗粒尺寸和颗粒形状。 相似文献
9.
颗粒破碎在岩土工程领域是很常见的现象,土工试验中无法显示颗粒破碎过程及其影响,本文采用离散单元软件PFC2D模拟了考虑颗粒破碎影响的粗粒土的直剪试验,给出了考虑颗粒破碎的粗粒土直剪试验的模拟方法,分析粗粒土的剪应力-剪切位移关系、剪胀和剪切强度等宏观力学行为,探讨基本颗粒间黏聚力、单颗粒孔隙率和粗粒土试样的孔隙率对剪切强度的影响。结果表明:颗粒破碎对剪切强度的破碎准则有影响,颗粒不破碎试样的剪切强度符合Mohr-Coulomb准则;颗粒破碎试样的强度包络线是幂函数关系。 相似文献
10.
在外荷载等因素作用下,粗粒土易发生颗粒破碎。对泥岩和砂岩颗粒进行了一系列的单颗粒破碎试验,基于尺寸效应和颗粒破碎分形模型,研究了单颗粒破碎强度、破碎能量及Weibull模量等与分形维数间的关系。利用PFC3D对单颗粒破碎过程进行分析,并与试验数据对比,验证了数值程序的可靠性;随后扩展到大颗粒粒径,分析了其单破碎强度及破碎能量。结果表明：在同类试验条件下,不同材料所得的分形维数是不同的;不同粒径砂岩的破碎程度均大于泥岩;单颗粒破碎强度具有明显的尺寸效应;单颗粒破碎强度与破碎能量均可通过分形维数与颗粒粒径预测得出;修正后的Weibull模量也可通过分形维数得出;数值模拟结果与试验结果及预测结果基本一致;大颗粒粒径单颗粒破碎强度模拟结果与预测结果基本一致,破碎能量稍有差异,需进一步试验验证。研究成果可为获取大粒径粗粒土的单颗粒强度与变形特性提供参考。 相似文献
11.
The post-construction settlement of rockfill dams and high filled ground of airport, which is a phenomenon of much significance, is mainly caused by the time-dependent breakage of the rockfill material. In this paper, a random virtual crack DEM model is proposed for creep behavior of rockfill in PFC2D according to the theory of subcritical crack propagation induced by stress corrosion mechanisms. The bonded clusters are adopted to represent the rockfill particles so as to simulate their irregular shapes. Virtual cracks are set at the bonds of the clusters, and the length of the crack is considered as a random value, which leads the crushing strength of a single particle to follow the Weibull’s statistical model and the corresponding size rules. Oedometric creep tests for rockfill are simulated by using this proposed model. The results show that the model, validated preliminarily by some test data, can reflect qualitatively the creep mechanism as well as the size effects reasonably. Particles can develop various breakage patterns during creep, including global breakage, local breakage and even complex mixed breakage. The increase in stress levels and particle size will lead to an obvious growth of the creep strain and creep rate of the rockfill. The scale effects on the creep behavior of rockfill are analyzed through 35 specimens, and formulas including the effects of scales and stress levels are tentatively proposed. 相似文献
12.
Calcareous sand is a typical problematic marine sediment because of its angular and porous particles. The effects of internal pores on the mechanical properties of calcareous sand particles have rarely been investigated. In this paper, the apparent morphology and internal structure of calcareous sand particles are determined by scanning electron microscopy and computed tomography tests, finding that the superficial pores connect inside and outside of the particles, forming a well-developed network of cavities and an internal porosity of up to 40%. The effects of particle morphology and internal porosity on the mechanical responses of particle were investigated by conducting photo-related compression test and 3D numerical simulations. Two failure modes are observed for the porous calcareous sand, i.e., compressive failure indicates that the particle skeleton is continually compressed and fragmented into small detritus without obvious splitting, and tensile failure indicates that the particles are broken into several fragments when the axial force clearly peaks. Calcareous sand particles with a high internal porosity or with small and dense pores often exhibit compressive failure, and vice versa. The particle strength is considerably reduced by increasing the internal porosity, but affected by pore size in nonlinear correlation. The crushing stress–strain points can be well fitted by an exponential curve, which is supplied for discussion. 相似文献
13.
颗粒破碎对颗粒材料宏观力学行为有重要影响。 结合Hardin的破碎经验公式,将表征破碎程度的破碎参量与Cosserat连续体的内部长度参数相关联,形成一个基于Cosserat连续体且能考虑颗粒破碎的弹塑性模型。数值算例主要考察了颗粒破碎对颗粒材料承载能力、塑性应变及局部化行为的影响,数值结果表明,颗粒破碎主要发生在剪切带内,颗粒破碎使得剪切带明显变窄且剪切带内外等效塑性应变梯度明显增大。 相似文献
14.
为了获得不同初始颗粒粒径分布和含水率对层间错动带颗粒破碎和剪切强度特性的影响,通过对比泥夹碎屑、泥夹粉砂、全泥型3种不同层间错动带类型与现场3种不同含水率（10%、7%和3%）试样在法向压力2～10 MPa作用下的反复直剪试验和剪切面颗粒粒径分析试验结果,可得出以下结论：①粗颗粒越多（d60越大）,采用相对颗粒破碎势Br量化的颗粒破碎程度越大;②较干颗粒（低含水率）由于磨损产生了更多的细小颗粒,而较湿颗粒（高含水率）由于破裂和摩擦产生了较大颗粒;③粗颗粒仅对峰值抗剪强度产生一定的影响,且粗颗粒越多,残余强度包线非线性越强;④黏聚力和内摩擦角随含水率线性减小,且低含水率试样残余强度包线非线性最强;⑤残余内摩擦角随颗粒破碎后的黏粒含量（<2 μm）线性减小。提出的残余内摩擦角初步预测公式可供实际工程参考。 相似文献
15.
颗粒的破碎强度随着粒径的增大而减小,即颗粒破碎的尺寸效应,分形模型为解释固体颗粒破碎的尺寸效应提供了可行的方法。根据岩石颗粒破碎时的分形特征,采用Sammis破碎准则,通过模拟分析得出岩石颗粒破碎能量和强度的分形模型,建立和验证用分维D来表示岩石颗粒破碎的能量和强度准则,得出并验证了岩石颗粒破碎分维的确定方法。利用离散元软件PFC2D的黏结颗粒模型BPM（Bonded Particle Model）模拟了小孔隙率n=0.12和大孔隙率n=0.3,即密实和松散两种情况。其中小孔隙率采用在模型上添加小颗粒的新方法,分别做了400组粒径不等的数值模拟试验,从粒径与破碎强度、破碎能量之间的关系和应力-应变曲线3个方面进行了统计,验证了岩石颗粒破碎强度与分维D的理论关系为σ f∝dD-3,并得出颗粒破碎时的能量和与分维D之间的关系为E f∝dD-1。验证了分形理论在分析颗粒破碎的尺寸效应中的较好应用,为确定岩石颗粒的破碎强度和岩石堆砌体剪切强度提供新的方法和参考意见。 相似文献
16.
目前对钙质土压缩特性的研究主要集中在钙质细砂,而实际工程中广泛存在钙质粗粒料,因此对钙质粗粒料压缩特性开展研究具有重要意义。通过颗粒强度测定仪和全自动大型固结仪对钙质土进行了单颗粒破碎试验和一维压缩试验,研究了颗粒粒径和相对密度对钙质粗粒料的颗粒强度和压缩特性的影响。单颗粒试验结果表明,钙质砂单颗粒的特征应力随着颗粒相对密度的增大而增大;单颗粒的破碎强度具有明显的尺寸效应,可利用单颗粒的特征应力进行标准化,且服从Weibull分布。压缩试验结果表明,单一粒径试样破碎后的分形维数随颗粒粒径的增大而增大;试样的Hardin破碎率与塑性功的关系为幂函数关系;在本次试验条件下,单一粒径试样的屈服应力与单颗粒的特征应力存在近似线性关系。 相似文献
17.
The high mobility of rapid landslides is one of the most important subjects of both theoretical and practical interest to engineers and scientists. The idea that ultralow resistance could explain the high mobility inspires researchers to examine the shear behavior of granular materials under a wide range of conditions, but the response of granular materials to fast loading rates is largely unknown. The motivation for this study was to examine several fundamental issues of particle properties and mechanical conditions on the fast shear behavior of granular materials. Two granular materials were studied in the oven-dried state and were sheared by employing a ring-shear apparatus. Results indicated that angular particles (silica sand) had higher shear strength parameters than spherical particles (glass beads). In addition, the dilative process was observed during shearing, which depended on normal stress and particle shape. A slightly negative shear-rate effect on shear strength was observed for both granular materials under a certain range of shear rates. Furthermore, cumulative shear displacement had a significant effect on the degree of particle crushing. Fast ring-shear tests also revealed that shear rate had a slightly negative effect on particle crushing. Based on these experimental results, the possible applications of dynamic grain fragmentation theory to assess the high mobility of rapid landsliding phenomena were discussed. It was indicated that the magnitude and release rate of elastic strain energy generated by grain fragmentation played important roles on the dynamic process of landslide mobility. 相似文献
18.
In granular soils grain crushing reduces dilatancy and stress obliquity enhances crushability. These are well-supported specimen-scale experimental observations. In principle, those observations should reflect some peculiar micromechanism associated with crushing, but which is it? To answer that question the nature of crushing-induced particle-scale interactions is here investigated using an efficient DEM model of crushable soil. Microstructural measures such as the mechanical coordination number and fabric are examined while performing systematic stress probing on the triaxial plane. Numerical techniques such as parallel and the newly introduced sequential probing enable clear separation of the micromechanical mechanisms associated with crushing. Particle crushing is shown to reduce fabric anisotropy during incremental loading and to slow fabric change during continuous shearing. On the other hand, increased fabric anisotropy does take more particles closer to breakage. Shear-enhanced breakage appears then to be a natural consequence of shear-enhanced fabric anisotropy. The particle crushing model employed here makes crushing dependent only on particle and contact properties, without any pre-established influence of particle connectivity. That influence does not emerge, and it is shown how particle connectivity, per se, is not a good indicator of crushing likelihood. 相似文献
19.
颗粒破碎是堆石料的一项基本特性,它对堆石体的变形和强度特性具有明显的影响。对于高堆石坝而言,在高应力场作用下堆石颗粒发生明显破碎,可导致坝体变形率增加。为了正确认识堆石体及堆石坝的变形特性和机理,研究了堆石颗粒破碎特性以及颗粒破碎的影响因素。采用大型三轴试验研究了堆石料的颗粒破碎特性,分析了堆石体干密度、级配特征、堆石颗粒强度等对颗粒破碎的影响,研究了应力状态对颗粒破碎率的影响,建立了颗粒破碎率的计算模型以及颗粒破碎引起的堆石体应变增量与颗粒破碎率的关系。 相似文献
20.
珊瑚单颗粒破碎特性与珊瑚砂高压缩性、剪缩性及良好蠕变性等宏观力学行为密切相关。珊瑚颗粒的应变率效应对于不同形式荷载作用下珊瑚砂强度与变形特性研究具有重要意义。对约300颗珊瑚颗粒进行0.1～50 mm/min位移速率下的单颗粒破碎试验,探讨加载应变速率对颗粒破碎强度、破碎模式、破碎能量及破碎分形的影响。结果表明,珊瑚颗粒破碎强度服从Weibull分布规律,且特征破碎强度随应变率的提高非线性增大;随着加载速率的增大,颗粒主劈裂破坏往往先于棱角的局部碎裂和表面研磨,相应的荷载?位移曲线呈现出由峰前“多峰”向峰后“多峰”现象转变;珊瑚颗粒破碎能量密度和破碎分形维数同样具有明显的应变率效应,且均与对数应变率呈线性正相关关系,表征能量耗散和破碎程度均随加载应变率的增大而增大。 相似文献
|
