共查询到20条相似文献，搜索用时 46 毫秒
1.
饱和粉砂不稳定性的试验研究 总被引：3，自引：0，他引：3
通过对净砂和级配良好粉砂(含10 %粉土)进行一系列三轴固结不排水试验（CU）,研究了粉土、孔隙比和围压对饱和粉砂不稳定性的影响。试验结果表明,净砂与粉砂在不排水剪切条件下均会出现应变软化现象（即不稳定性）。同一围压下脆性指数(IB)随孔隙比增加,但不稳定线的应力比随孔隙比增加而减小。引用等效粒间孔隙比(ege)后,净砂和粉砂在ege-ln p?平面上拥有基本相同的临界状态线。在临界状态理论及等效粒间孔隙比的基础上,提出在同一修正状态参数(?ge)下净砂和级配良好粉砂有相似的不稳定性。 相似文献
2.
Hanifi Missoum Mostefa Belkhatir Karim Bendani Mustapha Maliki 《Geotechnical and Geological Engineering》2013,31(1):279-296
In a number of recent case studies, the liquefaction of silty sands has been reported. To investigate the undrained shear and deformation behaviour of Chlef sand–silt mixtures, a series of monotonic and stress-controlled cyclic triaxial tests were conducted on sand encountered at the site. The aim of this laboratory investigation is to study the influence of silt contents, expressed by means of the equivalent void ratio on undrained residual shear strength of loose, medium dense and dense sand–silt mixtures under monotonic loading and liquefaction potential under cyclic loading. After an earthquake event, the prediction of the post-liquefaction strength is becoming a challenging task in order to ensure the stability of different types of earth structures. Thus, the choice of the appropriate undrained residual shear strength of silty sandy soils that are prone to liquefaction to be used in engineering practice design should be established. To achieve this, a series of undrained triaxial tests were conducted on reconstituted saturated silty sand samples with different fines contents ranging from 0 to 40 %. In all tests, the confining pressure was held constant at 100 kPa. From the experimental results obtained, it is clear that the global void ratio cannot be used as a state parameter and may not characterize the actual behaviour of the soil as well. The equivalent void ratio expressing the fine particles participation in soil strength is then introduced. A linear relationship between the undrained shear residual shear strength and the equivalent void ratio has been obtained for the studied range of the fines contents. Cyclic test results confirm that the increase in the equivalent void ratio and the fines content accelerates the liquefaction phenomenon for the studied stress ratio and the liquefaction resistance decreases with the increase in either the equivalent void ratio or the loading amplitude level. These cyclic tests results confirm the obtained monotonic tests results. 相似文献
3.
4.
以京津高铁和杭州地铁沿线的两种典型粉质黏土为研究对象,并采用英国GDS多功能三轴仪完成了静、动力强度测试,研究了两种土的静力不排水抗剪强度和在交通荷载高振次循环下的动强度、临界动应力比、应变发展模式以及振后抗剪强度等方面的差异。对比发现,长期循环荷载作用下两种土的应变发展和振后强度均有很大不同。与京津地区粉质黏土相比,杭州地铁沿线土含水率高、孔隙比大、密度低、灵敏度高、强度低。两种原状土在小幅振动后土体强度略有增大,而随振幅增大,振后强度将低于未经历振动时的不排水强度值;而重塑土振后强度均低于静剪强度。 相似文献
5.
Peijun Guo 《国际地质力学数值与分析法杂志》2013,37(4):353-373
By taking into account the continuity of stresses and pore pressure across the boundaries of a shear band, it is theoretically shown that incipient localization may take place in saturated loose contractive sand in the regime of decreasing deviator stress under undrained conditions. The undrained shear band orientation primarily depends on the Poisson's ratio and the dilatancy characteristics of the material. However, under strict isochoric constraint, localization is precluded in dense dilative sand with deviator stress increasing only. If any local volume change takes place with a certain mechanism, undrained shear band would be possible in dense sand, most likely in the regime of decreasing friction angle after the peak friction angle is mobilized. Numerical examples are given to demonstrate the variation of shear band inclinations with void ratios and initial consolidation pressures. Copyright © 2011 John Wiley & Sons, Ltd. 相似文献
6.
利用土工静力-动力液压-三轴扭转多功能剪切仪,针对相对密度为30 %的福建标准砂,进行了复杂初始固结条件下应力路径变化的应力控制式单调排水与不排水剪切试验。控制试验过程的平均主应力保持不变,变化中主应力系数和主应力方向,分别探讨在不同排水条件下中主应力系数和主应力方向对饱和砂土剪切特性的影响。通过对比表明：与排水条件无关,中主应力系数对归一化的应力-应变关系具有影响,但对体变或孔压的影响并不明显。初始条件相同,偏应力比随中主应力系数的增大而降低。主应力方向的影响同样显著,排水试验的主应力方向角不同时应力-应变关系所表现出的变化规律取决于水平面与竖直面上受到的剪应力作用。不排水试验的峰值有效偏应力比随着主应力方向角的增大而减小。 相似文献
7.
8.
通过对钙质砂进行不排水条件下声发射试验,探讨了不同围压、剪切速率、初始孔隙比和级配下钙质砂声发射规律。试验结果表明:低围压（围压低于400 kPa）时,钙质砂声发射活动频率随着围压的升高而增加;围压增至800 kPa时,声发射活动频率有所下降。低剪切速率下,钙质砂剪切试验明显分为颗粒破碎阶段和颗粒滑移阶段,随着剪切速率增大,二者之间较模糊,不能明显区分;松散和密实状态下,钙质砂声发射活动规律相似,钙质砂声发射活动频率均高于中密状态钙质砂;级配较好的钙质砂,声发射率峰值出现在试样发生剪切破坏前;级配稍差,试样声发射率相对均匀,声发射率峰值出现在邻近试验结束时。 相似文献
9.
The undrained shear behaviour of sands has been a key topic after the devastating geo-disasters during the 1964 Niigata Earthquake
in Japan. Extensive geo-technical soil tests, especially undrained triaxial compression tests, have revealed that the liquefaction
phenomenon was the major cause for the disaster expansions. To numerically reproduce the liquefaction phenomenon, the pore-water
pressure was coupled with a distinct element method. In this model, the dynamic changes in pore-water pressure were taken
into consideration by the changes in volumetric strain and modulus of compressibility of water in the respective measurement
spheres. Fluid-flows among the measurement spheres were controlled by Darcy’s law. The effective stress paths and steady state
strengths in undrained triaxial compression tests associated with the wide ranges of initial void ratio were investigated.
The effective mean stresses of medium-dense to dense numerical specimens at the steady state were negatively proportional
to the initial void ratio. Loose numerical specimens reproduced quasi-liquefaction with the effective mean stresses that were
less than 25% of the initial value. The medium-dense numerical specimens reproduced the phase transformation that was a typical
characteristic of granular materials. The rolling restraints did not much influence of the effective angle of internal friction
but strongly affected pore-water pressure behaviour within a certain range of initial void ratio. 相似文献
10.
常剪应力路径下含气砂土的三轴试验 总被引：1，自引：0，他引：1
天然气水合物完全分解时,产生的气体使得能源土孔隙压力急速增加,有效应力减小,进而引起土体液化破坏。此时深海能源土斜坡的应力状态与静力液化失稳过程可简化为含气土在常剪应力排水(或不排水)应力路径下的破坏问题。以此为背景,提出了制备含气砂土试样的改进充气管法,并开展了含气砂土的常剪应力路径三轴试验。22组试验结果表明:同一孔隙比的含气密砂在不同围压与常剪应力下具有相同的失稳线;含气砂土试样失稳时的应力比和体变均随初始相对密实度的增大而增大;含气密砂在常剪应力路径下饱和度对失稳特征影响的规律性在排水与不排水条件下均不明显,但在不排水条件下含气砂土的孔压(或体变)对变形的敏感性降低;含气密砂在常剪应力路径到达失稳点之后,排水条件下是瞬变的液化鼓胀破坏,不排水条件下是渐变的剪切破坏。 相似文献
11.
为了分析剪切条件下零有效应力状态砂土的流动变形规律,对传统环剪仪进行了试样可视化改造,研制了透明环形剪切盒,通过对剪切盒膨胀性能分析及与标准砂的剪切试验对比,验证了环剪装置改造的合理性。通过分析不排水条件下饱和悬浮塑料砂的剪应力-应变曲线,发现其剪切强度具有应变软化的特性。通过分析环剪仪中饱和悬浮塑料砂试样的有效应力,证实了可视环剪试验中的土体基本处于零有效应力状态。开展了饱和悬浮塑料砂的流动变形可视环剪试验研究,结果表明：饱和悬浮塑料砂在固结不排水条件下剪切变形不连续,直接在剪切面发生断裂;在不固结不排水的条件下饱和悬浮塑料砂的剪切变形表现出流动形态,且与剪切速率有关：在低剪切速率下,剪切变形仅在剪切面处形成具有曲线轨迹的流动变形而在其他区域不发生变形;而在高剪切速率下剪切变形为整体的倾斜变形,符合黏性流体的流动变形特征。 相似文献
12.
This paper evaluates the performance of a generalized effective stress soil model for predicting the rate independent behaviour of freshly deposited sands, while a companion paper describes model capabilities for clays and silts. Most material parameters can be obtained from standard laboratory data, including hydrostatic or one‐dimensional compression, drained and undrained triaxial shear testing. A compilation of data on compression behaviour allows for estimation of compression parameters when this type of data is not available. Extensive comparisons of model predictions with measured data from undrained triaxial shear tests shows that the model gives excellent predictions of the transition from dilative to contractive shear response as the confining pressure and/or the initial formation void ratio increases. A parametric study of drained response shows that the model describes realistically the variation of peak friction angle and dilation rate as a function of confining pressure and density when compared with an empirical correlation valid for many sands. The proposed formulation predicts a unique critical state locus for both drained and undrained triaxial testing which is non‐linear over the entire range of stresses and is in excellent agreement with recent experimental data. Overall, the model provides excellent predictions of the stress–strain–strength relationships over a wide range of confining pressures and formation densities. Copyright © 2002 John Wiley & Sons, Ltd. 相似文献
13.
中主应力对饱和松砂不排水单调剪切特性的影响 总被引：7，自引：0，他引：7
利用土工静力-动力液压-三轴扭转多功能剪切仪,针对相对密度为30 %的福建标准砂,在不排水条件下控制主应力方向、中主应力系数、平均主应力保持不变,进行了单调剪切试验。以此着重探讨了中主应力系数对相变有效内摩擦角、峰值有效内摩擦角及有效应力路径的影响。研究表明,中主应力系数对在不排水单调剪切条件下饱和松砂的强度参数具有显著的影响,而对有效应力路径及应力-应变关系发展模式影响较小。基于广义双剪强度准则,从理论上探讨了土的强度参数对于中主应力的依赖性,并与试验结果进行了对比。 相似文献
14.
动扭剪试验中砂土液化后流动特性分析 总被引：2，自引：0，他引：2
土体在初始液化后仍然可能承受动荷载作用发生大变形。引入流体力学中的剪应变率和表观黏度的概念,对振动扭剪试验中饱和砂土液化后的流动特性进行了分析。分析中将砂土的状态分为0有效应力状态和非0有效应力状态。结果表明,砂土在0有效应力状态下表现出与静扭剪试验类似的“剪切稀化”非牛顿流体的特征,表观黏度随着剪应变率的增大而减小。加载周数对“剪切稀化”状态下的剪应变率幅值有影响,随着加载周数的增加,剪应变率幅值逐渐增大,而对流动曲线的形状没有影响。在非0有效应力状态下,砂土的表观黏度随应变的增大而增大,随孔压比的减小而增大,且所有的试验得到的表观黏度与孔压比具有一致关系。 相似文献
15.
16.
Ali Lashkari 《Acta Geotechnica》2016,11(5):987-1014
Adding a small amount of non-plastic silt to clean sands may lead to dramatic loss of shear strength and a noteworthy tendency toward contraction when the mechanical behavior of the mixture is compared with that of the clean host sand. Thus, simulation of the behavior of silty sands with varying fines content is still a challenging subject in geomechanics. A unified constitutive model for clean and silty sands is presented in this paper. To eliminate the factitious decrease of void ratio associated with inactive silt particles in various silty sand mixtures, the concept of equivalent void ratio is used in the model formulation instead of the global void ratio. In addition, the instantaneous soil state is expressed in terms of intergranular state parameter taking into account the combined influence of intergranular void ratio, mean principal effective stress and fines content. Then, dilatancy and plastic hardening modulus are directly linked to the intergranular state parameter. To improve the model capacity in simulation of cyclic tests, new features are added to the plastic hardening modulus. It is shown that the proposed model can reasonably reproduce the mechanical behavior as well as the onset of flow liquefaction instability of clean and silty sands using a unique set of parameters. 相似文献
17.
为了模拟实际工程中黄土在不排水条件下的破坏,在控制含水率不变条件下,利用非饱和土真三轴仪对不同初始吸力非饱和原状黄土进行了等向固结试验和不同中主应力参数b值的剪切试验,研究了非饱和原状黄土的力学特性。研究结果表明：真三轴等向压缩屈服应力随着初始吸力的增大而增大,吸力随着净平均应力的增大而减小,净平均应力对吸力的影响程度随着初始吸力的增大而增大。不同 值条件下,广义剪应力和净平均应力破坏状态线近似呈平行直线关系,广义剪应力和有效净平均球应力试验点可归一为饱和土的排水剪切破坏状态线;剪切破坏时吸力随着b值的增大基本呈线性增大趋势;孔隙比和净平均应力对数临界状态线近似呈线性平行关系,其斜率比饱和土大,且大于等向压缩屈服前的斜率;非饱和土孔隙比和有效净平均球应力对数临界状态线与饱和土的临界状态线近似呈线性平行关系;不同净围压条件下,不同 值非饱和土与饱和土的破坏状态孔隙比的比值与气体饱和度的试验点分布于1.0～1.2的直线带内,但同一净有效球应力条件下可以归一为一条非线性曲线。 相似文献
18.
In this paper effect of fine mineralogy on mechanical behavior of unsaturated silty sand in different fine contents and divers confining pressure has been studied. All samples were molded with constant equivalent granular void ratio well-known parameter already proposed for characterizing silty sand behavior in saturated state. This manner of study allow to investigate also the validity of equivalent granular void ratio concept in unsaturated state. For this purpose, a series of triaxial tests were performed on the sand specimens with different percentages of silt in the undrained saturated (CU) and unsaturated (CW) conditions. The results showed that the material types and aggregate distribution of the fines have enormous effects on the silty sand behavior. In addition, the shear strength in the unsaturated specimens changed as a function of the initial applied matric suction. A fewer performance of equivalent intergranular void ratio in the case of unsaturated state in comparison of saturated states was observed.
相似文献19.
Based on previous experimental findings and theoretical developments, this paper presents the formulation and numerical algorithms of a novel constitutive model for sand with special considerations for cyclic behaviour and accumulation of large post-liquefaction shear deformation. Appropriate formulation for three volumetric strain components enables the model to accurately predict loading and load reversal behaviour of sand, fully capturing the features of cyclic mobility. Compliance with the volumetric compatibility condition, along with reversible and irreversible dilatancy, allows for physically based simulation of the generation and accumulation of shear strain at zero effective stress after initial liquefaction. A state parameter was incorporated for compatibility with critical state soil mechanics, enabling the unified simulation of sand at various densities and confining pressures with a same set of parameters. The determination methods for the 14 model parameters are outlined in the paper. The model was implemented into the open source finite-element framework OpenSees using a cutting-plane stress integration scheme with substepping. The potentials of the model and its numerical implementation were explored via simulations of classical drained and undrained triaxial experiments, undrained cyclic torsional experiments, and a dynamic centrifuge experiment on a single pile in liquefiable soil. The results showed the model’s great capabilities in simulating small to large deformation in the pre- to post-liquefaction regime of sand. 相似文献
20.
A simple semi-hyperbolic state-dependent constitutive model for sand-structure interfaces is proposed. The model formulation is consistent with critical state soil mechanics since void ratio evolves continuously with shear strain from initial state towards asymptotic critical state at extremely large shear strains. The model takes into account influence of normal stiffness on volume change and stress path. The proposed interface model is implemented in a pile segment analysis scheme for simulation of shaft resistance mobilization in non-displacement piles. Results reveal that the proposed pile segment analysis can well predict shaft resistance of model piles embedded in different sands. 相似文献