首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献，搜索用时 31 毫秒
1.
The geological storage of carbon dioxide is considered as one of the measures to reduce greenhouse gas emissions and to mitigate global warming. Operators of storage sites are required to demonstrate safe containment and stable behaviour of the storage complex that is achieved by geophysical and geochemical monitoring, combined with reservoir simulations. For site characterization, as well as for imaging the carbon dioxide plume in the reservoir complex and detecting potential leakage, surface and surface‐borehole time‐lapse seismic monitoring surveys are the most widespread and established tools. At the Ketzin pilot site for carbon dioxide storage, permanently installed fibre‐optic cables, initially deployed for distributed temperature sensing, were used as seismic receiver arrays, demonstrating their ability to provide high‐resolution images of the storage formation. A vertical seismic profiling experiment was acquired using 23 source point locations and the daisy‐chained deployment of a fibre‐optic cable in four wells as a receiver array. The data were used to generate a 3D vertical seismic profiling cube, complementing the large‐scale 3D surface seismic measurements by a high resolution image of the reservoir close to the injection well. Stacking long vibro‐sweeps at each source location resulted in vertical seismic profiling shot gathers characterized by a signal‐to‐noise ratio similar to gathers acquired using geophones. A detailed data analysis shows strong dependency of data quality on borehole conditions with significantly better signal‐to‐noise ratio in regions with good coupling conditions.  相似文献   

2.
Average elastic properties of a fluid‐saturated fractured rock are discussed in association with the extremely slow and dispersive Krauklis wave propagation within individual fractures. The presence of the Krauklis wave increases P‐wave velocity dispersion and attenuation with decreasing frequency. Different laws (exponential, power, fractal, and gamma laws) of distribution of the fracture length within the rock show more velocity dispersion and attenuation of the P‐wave for greater fracture density, particularly at low seismic frequencies. The results exhibit a remarkable difference in the P‐wave reflection coefficient for frequency and angular dependency from the fractured layer in comparison with the homogeneous layer. The biggest variation in behaviour of the reflection coefficient versus incident angle is observed at low seismic frequencies. The proposed approach and results of calculations allow an interpretation of abnormal velocity dispersion, high attenuation, and special behaviour of reflection coefficients versus frequency and angle of incidence as the indicators of fractures.  相似文献   

3.
It is well‐known that experimental or numerical backpropagation of waves generated by a point‐source/‐scatterer will refocus on a diffraction‐limited spot with a size not smaller than half the wavelength. More recently, however, super‐resolution techniques have been introduced that apparently can overcome this fundamental physical limit. This paper provides a framework of understanding and analysing both diffraction‐limited imaging as well as super resolution. The resolution analysis presented in the first part of this paper unifies the different ideas of backpropagation and resolution known from the literature and provides an improved platform to understand the cause of diffraction‐limited imaging. It is demonstrated that the monochromatic resolution function consists of both causal and non‐causal parts even for ideal acquisition geometries. This is caused by the inherent properties of backpropagation not including the evanescent field contributions. As a consequence, only a diffraction‐limited focus can be obtained unless there are ideal acquisition surfaces and an infinite source‐frequency band. In the literature various attempts have been made to obtain images resolved beyond the classical diffraction limit, e.g., super resolution. The main direction of research has been to exploit the evanescent field components. However, this approach is not practical in case of seismic imaging in general since the evanescent waves are so weak – because of attenuation, they are masked by the noise. Alternatively, improvement of the image resolution of point like targets beyond the diffraction limit can apparently be obtained employing concepts adapted from conventional statistical multiple signal classification (MUSIC). The basis of this approach is the decomposition of the measurements into two orthogonal domains: signal and noise (nil) spaces. On comparison with Kirchhoff prestack migration this technique is showed to give superior results for monochromatic data. However, in case of random noise the super‐ resolution power breaks down when employing monochromatic data and a limited acquisition aperture. For such cases it also seems that when the source‐receiver lay out is less correlated, the use of a frequency band may restore the super‐resolution capability of the method.  相似文献   

4.
The study site at Lamalou karst spring (Hortus karst plateau) is situated 40 km north of Montpellier in France. It consists of a limestone plateau, drained by a karst conduit discharging as a spring. This conduit extends for a few dozen meters in fractured and karstified limestone rocks, 15 to 70 m below the surface. The conduit is accessible from the surface. The main goal of this study is to analyze the surface part of the karst and to highlight the karstic features and among them the conduit, and to test the performances of ground penetrating radar (GPR) in a karstic environment. This method thus appears particularly well adapted to the analysis of the near-surface (<30 m in depth) structure of a karst, especially when clayey coating or soil that absorbs and attenuates the radar is rare and discontinuous. A GPR pulseEKKO 100 (Sensors and Software) was used on the site with a 50-MHz antenna frequency. The results highlight structures characterizing the karstic environment: the epikarst, bedding planes, fractured and karstified zones, compact and massive rock and karrens, a typical karst landform. One of the sections revealed in detail the main conduit located at a depth of 20 m, and made it possible to determine its geometry. This site offers possibilities of validation of the GPR data by giving direct access to the karstic conduits and through two cored boreholes. These direct observations confirm the interpretation of all the GPR sections.  相似文献   

5.
For 3‐D shallow‐water seismic surveys offshore Abu Dhabi, imaging the target reflectors requires high resolution. Characterization and monitoring of hydrocarbon reservoirs by seismic amplitude‐versus‐offset techniques demands high pre‐stack amplitude fidelity. In this region, however, it still was not clear how the survey parameters should be chosen to satisfy the required data quality. To answer this question, we applied the focal‐beam method to survey evaluation and design. This subsurface‐ and target‐oriented approach enables quantitative analysis of attributes such as the best achievable resolution and pre‐stack amplitude fidelity at a fixed grid point in the subsurface for a given acquisition geometry at the surface. This method offers an efficient way to optimize the acquisition geometry for maximum resolution and minimum amplitude‐versus‐offset imprint. We applied it to several acquisition geometries in order to understand the effects of survey parameters such as the four spatial sampling intervals and apertures of the template geometry. The results led to a good understanding of the relationship between the survey parameters and the resulting data quality and identification of the survey parameters for reflection imaging and amplitude‐versus‐offset applications.  相似文献   

6.
We present a novel application of the Kinect?, an input device designed for the Microsoft® Xbox 360® video game system. The device can be used by Earth scientists as a low‐cost, high‐resolution, short‐range 3D/4D camera imaging system producing data similar to a terrestrial light detection and ranging (LiDAR) sensor. The Kinect contains a structured light emitter, an infrared camera (the combination of these two produce a distance image), a visual wavelength camera, a three‐axis accelerometer, and four microphones. The cost is ~ US $100, frame rate is 30 Hz, spatial and depth resolutions are mm to cm depending on range, and the optimal operating range is 0.5 to ~5 m. The resolution of the distance measurements decreases with distance and is ≤1 mm at 0.5 m and ~75 mm at 5 m. We illustrate data collection and basic data analysis routines in three experiments designed to demonstrate the breadth and utility of this new sensor in domains of glaciology, stream bathymetry, and geomorphology, although the device is applicable to a number of other Earth science fields. Copyright © 2012 John Wiley & Sons, Ltd.  相似文献   

7.
Attempts have previously been made to predict anisotropic permeability in fractured reservoirs from seismic Amplitude Versus Angle and Azimuth data on the basis of a consistent permeability‐stiffness model and the anisotropic Gassmann relations of Brown and Korringa. However, these attempts were not very successful, mainly because the effective stiffness tensor of a fractured porous medium under saturated (drained) conditions is much less sensitive to the aperture of the fractures than the corresponding permeability tensor. We here show that one can obtain information about the fracture aperture as well as the fracture density and orientation (which determines the effective permeability) from frequency‐dependent seismic Amplitude Versus Angle and Azimuth data. Our workflow is based on a unified stiffness‐permeability model, which takes into account seismic attenuation by wave‐induced fluid flow. Synthetic seismic Amplitude Versus Angle and Azimuth data are generated by using a combination of a dynamic effective medium theory with Rüger's approximations for PP reflection coefficients in Horizontally Transversely Isotropic media. A Monte Carlo method is used to perform a Bayesian inversion of these synthetic seismic Amplitude Versus Angle and Azimuth data with respect to the parameters of the fractures. An effective permeability model is then used to construct the corresponding probability density functions for the different components of the effective permeability constants. The results suggest that an improved characterization of fractured reservoirs can indeed be obtained from frequency‐dependent seismic Amplitude Versus Angle and Azimuth data, provided that a dynamic effective medium model is used in the inversion process and a priori information about the fracture length is available.  相似文献   

8.
A comprehensive controlled source electromagnetic (CSEM) modelling study, based on complex resistivity structures in a deep marine geological setting, is conducted. The study demonstrates the effects of acquisition parameters and multi‐layered resistors on CSEM responses. Three‐dimensional (3D) finite difference time domain (FDTD) grid‐modelling is used for CSEM sensitivity analysis. Interpolation of normalized CSEM responses provides attributes representing relative sensitivity of the modelled structures. Modelling results show that fine grid, 1 × 1 km receiver spacing, provides good correlations between CSEM responses and the modelled structures, irrespective of source orientation. The resolution of CSEM attributes decreases for receiver spacing >2 × 2 km, when using only in‐line data. Broadside data in the grid geometry increase data density by 100 – approximately 200% by filling in in‐line responses and improve the resolution of CSEM attributes. Optimized source orientation (i.e., oblique to the strike of an elongated resistor) improves the structural definition of the CSEM anomalies for coarse‐grid geometries (receiver spacing ≥3 × 3 km). The study also shows that a multi‐resistor anomaly is not simply the summation but a cumulative response with mutual interference between constituent resistors. The combined response of constituent resistors is approximately 50% higher than the cumulative response of the multi‐resistor for 0.5 Hz at 4000 m offset. A gradual inverse variation of offset and frequency allows differentiation of CSEM anomalies for multi‐layered resistors. Similar frequency‐offset variations for laterally persistent high‐resistivity facies show visual continuity with varying geometric expressions. 3D grid‐modelling is an effective and adequate tool for CSEM survey design and sensitivity analysis.  相似文献   

9.
In this study, the derivative analysis using the derivative of drawdown with respect to log‐time was utilized to determine candidates for hydraulic conductor domains (HCDs). At a 500‐m deep borehole in the study site, the fractured rocks crossing the borehole were first classified in fractured and nonfractured zones by core logging and geophysical loggings, such as acoustic televiewing, density, and flow loggings. After conducting the hydraulic tests such as constant head withdrawal and recovery tests at the fractured zones and the nonfractured zones, the derivative analyses were carried out, of which the results were evaluated to determine the candidates for HCDs. For the nonfractured zones, the diagnostic plot has only a big hump indicating poor connection of the background fractures to the permeable geologic media, while those of the candidates for HCDs show various flow regimes. On the basis of these results, the candidates for HCDs among the fractured zones were determined. From discussion on the results, the combination of the spacing analysis and derivative analysis following a hydraulic test is recommended for determining the candidates for HCDs rather than other geophysical loggings.  相似文献   

10.
A constrained 3D density model of the upper crust along a part of the Deccan Syneclise is carried out based on the complete Bouguer anomaly data. Spectral analysis of the complete Bouguer gravity anomaly map of the study region suggests two major sources: short wavelength anomalies (<100 km) caused primarily due to the density inhomogeneities at shallow crustal level and long wavelength anomalies (>100 km) produced due to the sources deeper than the upper crust. A residual map of the short wavelength anomalies is prepared from the complete Bouguer anomaly using Butterworth high‐pass filter (100 km cut‐off wavelength). Utilizing the constraints from deep resistivity sounding, magnetotellurics and deep seismic sounding studies, 2.5D density models have been generated along 39 profiles of this region. The mismatch between the calculated response of the a priori 2.5D model with the residual (short wavelength) gravity anomalies is minimized by introducing high‐density intrusive bodies (≥2.81 g/cm3) in the basement. With these 2.5D density models, the initial geometry of our 3D density model, which includes alluvium, Deccan trap, Mesozoic sediment and high‐density intrusive bodies in the basement up to a depth of 7 km (upper crust), is generated. In the final 3D model, Deccan trap extends from 200 m to nearly 1700 m below the 90–150 m thick Quaternary sediment. Further down, the sub‐trappean Mesozoic sediment is present at a depth range of 600–3000 m followed by the basement. The derived 3D density model also indicates six intrusive bodies of density 2.83 g/cm3 in the basement at an average depth of about 4–7 km that best fits the residual gravity anomaly of the study area.  相似文献   

11.
Naturally fractured reservoirs are becoming increasingly important for oil and gas exploration in many areas of the world. Because fractures may control the permeability of a reservoir, it is important to be able to find and characterize fractured zones. In fractured reservoirs, the wave‐induced fluid flow between pores and fractures can cause significant dispersion and attenuation of seismic waves. For waves propagating normal to the fractures, this effect has been quantified in earlier studies. Here we extend normal incidence results to oblique incidence using known expressions for the stiffness tensors in the low‐ and high‐frequency limits. This allows us to quantify frequency‐dependent anisotropy due to the wave‐induced flow between pores and fractures and gives a simple recipe for computing phase velocities and attenuation factors of quasi‐P and SV waves as functions of frequency and angle. These frequency and angle dependencies are concisely expressed through dimensionless velocity anisotropy and attenuation anisotropy parameters. It is found that, although at low frequencies, the medium is close to elliptical (which is to be expected as a dry medium containing a distribution of penny‐shaped cracks is known to be close to elliptical); at high frequencies, the coupling between P‐wave and SV‐wave results in anisotropy due to the non‐vanishing excess tangential compliance.  相似文献   

12.
Common prestack fracture prediction methods cannot clearly distinguish multiplescale fractures. In this study, we propose a prediction method for macro- and mesoscale fractures based on fracture density distribution in reservoirs. First, we detect the macroscale fractures (larger than 1/4 wavelength) using the multidirectional coherence technique that is based on the curvelet transform and the mesoscale fractures (1/4–1/100 wavelength) using the seismic azimuthal anisotropy technique and prestack attenuation attributes, e.g., frequency attenuation gradient. Then, we combine the obtained fracture density distributions into a map and evaluate the variably scaled fractures. Application of the method to a seismic physical model of a fractured reservoir shows that the method overcomes the problem of discontinuous fracture density distribution generated by the prestack seismic azimuthal anisotropy method, distinguishes the fracture scales, and identifies the fractured zones accurately.  相似文献   

13.
Reconstruction of seismic data is routinely used to improve the quality and resolution of seismic data from incomplete acquired seismic recordings. Curvelet‐based Recovery by Sparsity‐promoting Inversion, adapted from the recently‐developed theory of compressive sensing, is one such kind of reconstruction, especially good for recovery of undersampled seismic data. Like traditional Fourier‐based methods, it performs best when used in conjunction with randomized subsampling, which converts aliases from the usual regular periodic subsampling into easy‐to‐eliminate noise. By virtue of its ability to control gap size, along with the random and irregular nature of its sampling pattern, jittered (sub)sampling is one proven method that has been used successfully for the determination of geophone positions along a seismic line. In this paper, we extend jittered sampling to two‐dimensional acquisition design, a more difficult problem, with both underlying Cartesian and hexagonal grids. We also study what we term separable and non‐separable two‐dimensional jittered samplings. We find hexagonal jittered sampling performs better than Cartesian jittered sampling, while fully non‐separable jittered sampling performs better than separable jittered sampling. Two other 2D randomized sampling methods, Poisson Disk sampling and Farthest Point sampling, both known to possess blue‐noise spectra, are also shown to perform well.  相似文献   

14.
The possibility of using 4D seismic data for monitoring pressure depletion in the low‐porosity, tight gas‐bearing Rotliegende sandstones of the UK Southern Gas Basin is investigated. The focus here is on whether fractures in the upper part of the reservoir, known to enhance productivity, can also enhance the time‐lapse seismic response. The study uses laboratory data to evaluate core‐plug stress sensitivity, published data for the stress behaviour of the fractures, followed by petro‐elastic and 4D seismic modelling of both the fractured and unfractured formation. The magnitude of the resultant 4D signatures suggests that production‐induced changes in the unfractured sands are unlikely to be observed except perhaps with highly repeatable time‐lapse surveys. On the other hand, the presence of fractures could render production effects visible in dedicated 4D acquisition or prestack parallel processed data. If present however, the signature will be sporadic, as fractures in the area are known to exist in clusters. The 4D signature may be enhanced further by certain classes of vertical geological variability and also areas of high reservoir pressure. The strongest evidence of depletion is expected to be time‐shifts seen at the base of the Rotliegende reservoir.  相似文献   

15.
Since natural fractures in petroleum reservoirs play an important role in determining fluid flow during production, knowledge of the orientation and density of fractures is required to optimize production. This paper outlines the underlying theory and implementation of a fast and efficient algorithm for upscaling a Discrete Fracture Network (DFN) to predict the fluid flow, elastic and seismic properties of fractured rocks. Potential applications for this approach are numerous and include the prediction of fluid flow, elastic and seismic properties for fractured reservoirs, model‐based inversion of seismic Amplitude Versus Offset and Azimuth (AVOA) data and the optimal placement and orientation of infill wells to maximize production. Given that a single fracture network may comprise hundreds of thousands of individual fractures, the sheer size of typical DFNs has tended to limit their practical applications. This paper demonstrates that with efficient algorithms, the utility of Discrete Fracture Networks can be extended far beyond mere visualization.  相似文献   

16.
We present a finite difference (FD) method for the simulation of seismic wave fields in fractured medium with an irregular (non-flat) free surface which is beneficial for interpreting exploration data acquired in mountainous regions. Fractures are introduced through the Coates-Schoenberg approach into the FD scheme which leads to local anisotropic properties of the media where fractures are embedded. To implement surface topography, we take advantage of the boundary-conforming grid and map a rectangular grid onto a curved one. We use a stable and explicit second-order accurate finite difference scheme to discretize the elastic wave equations (in a curvilinear coordinate system) in a 2D heterogeneous transversely isotropic medium with a horizontal axis of symmetry (HTI). Efficiency tests performed by different numerical experiments clearly illustrate the influence of an irregular free surface on seismic wave propagation in fractured media which may be significant to mountain seismic exploration. The tests also illustrate that the scattered waves induced by the tips of the fracture are re-scattered by the features of the free surface topography. The scattered waves provoked by the topography are re-scattered by the fractures, especially Rayleigh wave scattering whose amplitudes are much larger than others and making it very difficult to identify effective information from the fractures.  相似文献   

17.
This paper highlights the efficiency and complementarity of a light package of geophysical techniques to study the structure of karst Unsaturated Zone (UZ) in typical Mediterranean environment where soil cover is thin or absent. Both selected techniques, 2D Ground Penetrating Radar (GPR) and Electrical Resistivity Tomography (ERT), are widely used in environmental studies and their application is accessible for a lot of scientists/engineers. However, GPR or ERT alone is not able to provide an enhanced characterization of geological features in karst media. In the present study, GPR results supply a near surface high resolution imaging and thus can provide relevant geological information such as stratifications and fractures. Despite the quality of the results GPR's investigation depth remains limited to around 12 m. Apparent and inverted resistivity provided by ERT surveys shows strong lateral and vertical variations. These variations can inform about general geological structuring and feature orientation. ERT is able to prospect down to 40 m but it's a low resolution integrative technique. In the study area the investigated limestone is a commonly electrical resistive formation (more than 2000 Ω.m). However deeper than 5–7 m, the ERT profiles reveal several zones of moderate resistivity (around 900 Ω.m). In these zones a stratification change corresponding to slanted bedding is clearly identified by GPR results. The combination of both GPR and ERT results can allow a well-established geological interpretation. These moderate resistivity zones with slanted beddings can explain the presence of a perennial water flow point 35 m below the surface of the studied site within the underground gallery of the Low-Noise Underground Laboratory (LSBB).  相似文献   

18.
We present an approach that creates the possibility of reservoir monitoring on a quasi‐continuous basis using surface seismic data. Current strategies and logistics for seismic data acquisition impose restrictions on the calendar‐time temporal resolution obtainable for a given surface‐seismic time‐lapse monitoring program. One factor that restricts the implementation of a quasi‐continuous monitoring program using conventional strategies is the time it takes to acquire a complete survey. Here quasi‐continuous monitoring describes the process of reservoir monitoring at short‐time intervals. Our approach circumvents the restriction by requiring only a subset of complete survey data each time an image of the reservoir is needed using surface seismic data. Ideally, the time interval between survey subset acquisitions should be short so that changes in the reservoir properties are small. The accumulated data acquired are used to estimate the unavailable data at the monitor survey time and the combined recorded and estimated data are used to produce an image of the subsurface for monitoring. We will illustrate the effectiveness of our approach using 2D and 3D synthetic seismic data and 3D field seismic data. We will explain the benefits and drawbacks of the proposed approach.  相似文献   

19.
This paper describes least‐squares reverse‐time migration. The method provides the exact adjoint operator pair for solving the linear inverse problem, thereby enhancing the convergence of gradient‐based iterative linear inversion methods. In this formulation, modified source wavelets are used to correct the source signature imprint in the predicted data. Moreover, a roughness constraint is applied to stabilise the inversion and reduce high‐wavenumber artefacts. It is also shown that least‐squares migration implicitly applies a deconvolution imaging condition. Three numerical experiments illustrate that this method is able to produce seismic reflectivity images with higher resolution, more accurate amplitudes, and fewer artefacts than conventional reverse‐time migration. The methodology is currently feasible in 2‐D and can naturally be extended to 3‐D when computational resources become more powerful.  相似文献   

20.
In adapting the prestack migration technique used in seismic imaging to the inversion of ground‐penetrating radar (GPR) from time‐ to depth‐sections, we show that the theoretical integral formulation of the inversion can be applied to electromagnetic problems, albeit with three assumptions. The first two assumptions concern the electromagnetic characteristics of the medium, primarily that the medium must be perfectly resistive and non‐dispersive, and the third concerns the antennae radiation pattern, which is taken to be 2D. The application of this adaptation of the inversion method is confirmed by migrating actual GPR measurements acquired on the test site of the Laboratoire Central des Ponts et Chaussées. The results show good agreement with the geometry of the structures in the medium and confirm that the possible departure from the assumption of a purely resistive medium has no visible effect on the information concerning the geometry of scattering and reflecting structures. The field experiments also show that prestack migration processing is sufficiently robust with regard to the assumption of a non‐dispersive medium. The assumption of a 2D antennae radiation pattern, however, produces artefacts that could be significant for laterally heterogeneous media. Nevertheless, where the medium is not highly laterally heterogeneous, the migration gives a clear image of the scattering potential due to the geometry of structural contrasts in the medium; the scatterers are well focused from diffraction hyperbolae and well localized. Spatial geometry has limited dimensional accuracy and positions are located with a maximum error equal to the minimum wavelength of the signal bandpass. Objects smaller than one wavelength can nevertheless be detected and well focused if their dielectric contrasts are sufficiently high, as in the case of iron or water in gneiss gravels. Furthermore, the suitability of multi‐offset protocols to estimate the electromagnetic propagating velocity and to decrease the non‐coherent noise level of measurements is confirmed. Our velocity estimation is based on the semblance calculation of multi‐offset migrated images, and we confirmed the relevance of this quantification method using numerical data. The signal‐to‐noise ratio is improved by summing multi‐offset results after the addition of random noise on measurements. Thus the adaptation of prestack migration to multi‐offset radar measurements significantly improves the resolution of the scattering potential of the medium. Limitations associated with the methods used here suggest that 3D algorithms should be applied to strongly laterally heterogeneous media and further studies concerning the waveform inversion are necessary to obtain information about the electric nature of the medium.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号