首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献，搜索用时 31 毫秒
1.
Electrical resistance heating (ERH) is a thermal treatment technology that involves passing electrical current through soil to increase subsurface temperatures. In addition to volatizing and recovering contaminant mass in the gas phase, heating the subsurface has the potential to decompose contaminants by increasing the rate of degradation reactions. Prior laboratory studies using convective heating demonstrated that the rate of tetrachloroethene (PCE) degradation was not sufficient to cause substantial in situ PCE mass destruction. However, similar experiments have not been performed using ERH, which has the potential to degrade PCE in reaction with the heating electrodes and electrochemically. Thus, the objective of this study was to determine the extent of PCE degradation during thermal treatment of PCE‐contaminated soil using a bench‐scale ERH system. The contaminated soil, a silty clay loam, was collected from a single borehole at a former dry cleaning facility prior to undergoing ERH treatment. After 30 days of ERH, 52% of the initial PCE mass was recovered, potentially indicating that 48% of the PCE was degraded during ERH. Although potential degradation products such as carbon dioxide were observed, their presence was attributed to the degradation of soil organic carbon and carbonates rather than PCE destruction. A second ERH experiment was conducted to assess the potential benefit of adding the heat‐activated oxidant, sodium‐persulfate, during treatment. After 19 days of ERH and three persulfate injections, 93% of the initial PCE was recovered, with 3% PCE destruction based on chloride evolution. However, the difference in mass recovery between the first and second experiments could have been due to differences in the initial mass of PCE, even though soil from the same core was used in both experiments. The results of this work suggest that the majority of mass recovered during ERH of the PCE‐contaminated soil at the former dry cleaning facility will be due to volatilization and gas phase extraction rather than abiotic degradation, even with the addition of sodium persulfate.  相似文献   

2.
In situ thermal-based soil and aquifer remediation technologies (e.g., electrical resistance heating [ERH], conductive heating, and steam-based heating) have undergone rapid development and application in recent years. These thermal technologies offer the promise of more rapid and thorough treatment of nonaqueous phase liquid (NAPL) source zones; however, their field-scale application has not been well documented in the technical literature. A state-of-the-practice review of the application of these technologies was conducted in this study. Available documents from 182 applications were reviewed, which included 87 ERH, 46 steam-based heating, 26 conductive heating, and 23 other heating technology applications conducted between 1988 and 2007. Approximately 90% of the 182 applications were implemented after 1995 and about half since 2000. More specifically, this review identified the geologic settings in which these technologies were applied, chemicals treated, design parameters, operating conditions, and performance metrics. The results of this study are summarized in a table linking this information to five generalized geologic scenarios. Practitioners considering thermal technologies for their site can identify the geologic scenario that most closely resembles their site and then can quickly see which technologies have been applied in that setting, the designs employed, operating conditions, and the performance achieved.  相似文献   

3.
Numerical modeling was employed to study the performance of thermal conductive heating (TCH) in fractured shale under a variety of hydrogeological conditions. Model results show that groundwater flow in fractures does not significantly affect the minimum treatment zone temperature, except near the beginning of heating or when groundwater influx is high. However, fracture and rock matrix properties can significantly influence the time necessary to remove all liquid water (i.e., reach superheated steam conditions) in the treatment area. Low matrix permeability, high matrix porosity, and wide fracture spacing can contribute to boiling point elevation in the rock matrix. Consequently, knowledge of these properties is important for the estimation of treatment times. Because of the variability in boiling point throughout a fractured rock treatment zone and the absence of a well-defined constant temperature boiling plateau in the rock matrix, it may be difficult to monitor the progress of thermal treatment using temperature measurements alone.  相似文献   

4.
A recent study assessing the state‐of‐the‐practice of in situ thermal remediation technologies (e.g., electrical resistive heating [ERH], conductive heating, steam‐based heating, in situ large‐diameter auger soil mixing with steam/hot air injection, and radio‐frequency heating) identified 182 applications in the 1988 to 2007 period and summarized the geologic settings in which these technologies were applied, chemicals treated, design parameters, and operating conditions. That study concluded that documentation for less than 8% of those applications contained sufficient data to assess the effect remediation had on groundwater quality. Consequently, post‐treatment data were collected at five ERH sites, with emphasis on assessing reductions in dissolved groundwater concentrations and mass discharge (mass flux) to the aquifer. For each site, dissolved groundwater concentrations and hydraulic conductivities were determined across a vertical transect oriented perpendicular to groundwater flow and at the downgradient edge of the treatment zone. Dissolved concentration and mass discharge reductions ranged from about less than 10× to 100×, with post‐treatment groundwater concentrations ranging from about 101 to 104μg/L and mass discharges ranging from about 10–1 to 102 kg/y. The primary factors differentiating sites with greater and lesser dissolved concentration and mass discharge reductions were the adequacy of pre‐treatment source zone delineation, the extent to which the treatment zone encompassed the source zone, and the duration of treatment at the design operating temperature. The results suggest that ERH systems are capable of reducing groundwater concentrations to 10 to 100 μg/L levels and lower in some settings, but only if the source zone is adequately delineated and fully encompassed by the treatment system, and the treatment system is operated for a sufficiently long period of time.  相似文献   

5.
Capillary pressure (Pc)–saturation (S)–relative permeability (kr) relationships must be quantified to accurately predict non-aqueous phase liquid (NAPL) distribution in the subsurface. Several experimental techniques are presented here for two-fluid Pc–S–kr relationships for various saturation paths to better define the effect of fractional wettability on these relationships. During the primary drainage path of the Pc–S curves, the air–water system showed no distinct trend as a function of the fraction of sand treated by organosilane (S) to render it non-water wetting. In a NAPL–water system, however, a consistent decrease of capillary pressure with increase of the fraction of non-water wetting sands was observed. The much lower contact angle for air–water (a–w) system may result in the observed insensitivity of the a–w Pc–S curves to fractional wettability, at least for the PD pathway. For the main imbibition path of NAPL–water system, capillary pressure decreased as the fraction of the S component increased, requiring forced imbibition (negative capillary pressures) for a certain range of saturations. Systems with an increasing percentage of the S component also exhibited a higher water kr and lower NAPL or air kr at a given saturation for the primary drainage and main imbibition paths in both air–water and NAPL–water systems. The increase of water kr with increase of the fraction of the S component can be explained by the ability of water to occupy larger and highly conductive pores in such a system. Experimental kr–S data for the primary drainage path of NAPL–water system presented here were used to test the Bradford et al. [Bradford SA, Abriola LM, Leij FJ. Wettability effects on two- and three-fluid relative permeabilities. J Contam Hydrol 1997;28:171–91] model and the modified Mualem model for estimating the kr–S curves from measured Pc–S data as a function of fractional wettability. Both models predicted significantly less variation in the kr–S curves than measured indicating that they did not adequately represent the system under investigation.  相似文献   

6.
Nonaqueous phase liquid (NAPL)‐impacted lower permeability layers in heterogeneous media are difficult to fully remediate and can act as persistent sources of groundwater contamination through diffusive emissions to transmissive aquifer zones. This work investigated the benefits of partial remediation involving treatment focused near the high‐low permeability interface, with the performance metric being emissions reduction. A sequential base‐activated persulfate (S2O8 2?) delivery treatment strategy was studied in this work, involving 13–14 d deliveries of 10% w/w sodium persulfate (Na2S2O8) and 14–28 d deliveries of 19 g/L sodium hydroxide (NaOH). Treatment and control experiments were conducted in 1.2‐m wide × 1.2‐m tall × 5‐cm thick physical model tanks containing two soil layers differing in hydraulic conductivity by three orders of magnitude. The top 10 cm of the lower permeability layers contained 7400–7800 mg‐NAPL/kg‐soil; the NAPL was comprised of benzene, toluene, ethylbenzene, p‐xylene, o‐xylene, n‐propylbenzene, and 1,3,5‐trimethylbenzene (TMB) mixed in octane. Approximately 0.1 g‐Na2S2O8 was delivered per cm2‐interface area over 13–14 d. The S2O8 2? and SO4 2? concentration profiles suggest higher oxidant reaction rates when NaOH is delivered prior to, rather than after Na2S2O8. After 264 d and two treatments, hydrocarbon emissions from the NAPL source were reduced by 60% to 73% compared to a no‐treatment control tank. The incremental benefit of the second treatment was only about 10% of the effect of the first treatment.  相似文献   

7.
In the Kapurdi block of the Barmer lignite field in western Rajasthan, India, lignite occurs as a number of discontinuous seams of varying thickness up to a few m. The country rock is a succession of clay, sand and various members of the clay-sand family. The overburden, comprising sand, Fuller's earth, bentonitic clay, clayey sand/sandy clay and clay, is thick and, electrically, highly conductive. Both its thickness (40–90 m) and conductivity (0.5–1.0 S/m) are highly variable. The lignite seams may occur anywhere in the clay-sand sequence below this overburden. A ten-layered electrical model of the Kapurdi area was parameterized on the basis of galvanic resistivity sounding and core drilling results. This model was then validated by electromagnetic sounding measurements made with a 200 × 200 m square loop transmitter and energizing current of variable frequency (80 Hz to 11 kHz), using central induction sounding techniques. With a loop of this size, only formations in the overburden could be mapped. Subsequent computer modeling has shown that a larger loop of size, say, 800 m and a frequency band of 30–500 Hz are required to map formations below–as well as those within–the overburden. Even then only various clay-sand interfaces can be mapped, i.e., only over-burden thickness and the likely depth range of lignite seams (if they occur) can be estimated. Direct mapping of lignite seams is not feasible in practice. This is true of loop-dipole, as well as central induction sounding. It is interesting that skin depth need not always be a factor limiting depth of exploration in electromagnetic prospecting.  相似文献   

8.
Nonaqueous phase liquid (NAPL) is a long-term source of ground water contamination as the pollutant slowly partitions into the air and water phases. The objective of this work was to study the efficacy of aqueous surfactant solution to enhance the dissolution of a residual NAPL below the capillary fringe, hence reducing the time needed for aquifer restoration. An analytical technique was developed to measure the concentration of NAPL in a nonionic surfactant. Soil column experiments simulated conditions in the saturated soil where a NAPL may become trapped as a discontinuous immobile phase. Experimental results indicate that dissolution was a rate-limited process, approaching equilibrium concentrations after 24 hours. The relative permeability of the aqueous phase initially decreased as surfactant was injected, but increased over time as the saturation of residual NAPL was reduced through mass transfer into the surfactant-enhanced aqueous phase. These findings suggest that enhancing the aqueous phase with a nonionic surfactant may significantly enhance the in situ recovery or residual NAPL.  相似文献   

9.
Water exchange across the sediment–water interface of streams impresses a characteristic thermal pattern at the interface. The use of fibre optic distributed temperature sensing at the sediment–water interface in a small sand‐bed stream identifies such temperature patterns. Groundwater and interflow can be differentiated based on the temporal evolution of temperature patterns. Additionally, sudden temperature changes at the sediment–water interface observed during the transit of floods enable spatial identification of local up and downwelling. Electromagnetic induction geophysics can detect subsurface texture structures that support groundwater–surface water exchange. Our results show that areas of permanent temperature anomalies observed with fibre optic distributed temperature sensing match areas of comparatively homogeneous electrical conductivity. This indicates groundwater discharge and enables differentiating groundwater discharge from interflow and local downwelling.  相似文献   

10.
Crushed recycled glass was evaluated as an alternative to silica sand in dual‐media filters. Pilot scale inline filtration experiments were carried out using raw waters from three different water sources with turbidities between 6.0 and 14.0 NTU. Two physically identical filter columns were operated in parallel in the experiments. One filter consisted of 62.5 cm silica sand and 41.5 cm anthracite coal, whereas the other filter contained 62.5 cm crushed recycled glass plus 41.5 cm anthracite coal. The total bed depth was 104 cm for both filters. The properties of the media were as follows: Glass effective size = 0.77 mm, uniformity coefficient = 1.41. Sand effective size = 0.79 mm, uniformity coefficient = 1.33. Coal effective size = 1.45 mm, uniformity coefficient = 1.39. Experiments were repeated five times as follows: (i) Without the use of a coagulant, (ii–iii) with 5 and 10 mg/L of alum, and (iv–v) with 5 and 10 mg/L of ferric chloride. The filtration rate used was 11.5 m/h. Turbidity, particle counts, and head losses were measured and compared as functions of time. The following were observed: (i) Effluent turbidities and particle counts of the two filters were very close, i.e., essentially the same effluent quality was obtained when crushed glass was used instead of silica sand. (ii) In the majority of the tests, the filter with crushed glass generated both a smaller clean‐bed head loss and smaller clogging head losses than those of the filter containing sand. It is concluded that crushed glass may be a good alternative to silica sand in dual‐media filtration.  相似文献   

11.
Using numerical modelling, we investigate the evolution of seismoelectric effects induced by seismic excitation in spatially confined lithological units. Typical geometries represent clay lenses embedded in an aquifer or petroleum deposits in a host rock. In fluid‐saturated rocks, seismic waves can generate electromagnetic fields due to electrokinetic coupling mechanisms associated with such processes in the vicinity of the fluid‐mineral interface. Two seismoelectric phenomena are investigated: (1) the co‐seismic field associated with the seismic displacement at each point in a subsurface and (2) the interface response generated at layer boundaries. Our modelling uses a simplified time‐domain formulation of the coupled problem and an efficient 2D finite‐element implementation. To gain insight into the morphogenetic field behaviour of the seismoelectric effects, several numerical simulations for various target geometries were treated. Accordingly, we varied both the thickness of the confined units and the value of the electrical bulk conductivity in porous media. Analysis of these effects shows differences between interface responses for electrically conductive versus resistive units. So the pertinent contrast in electrical bulk conductivity controls the shape and structure of these seismoelectric conversion patterns. Moreover, the seismoelectric interface response captures both the petrophysical and geometrical characteristics of the geological unit. These models demonstrate the value of using seismoelectric interface response for reservoir characterization in either hydrogeological or hydrocarbon exploration studies.  相似文献   

12.
We measured in the laboratory ultrasonic compressional and shear‐wave velocity and attenuation (0.7–1.0 MHz) and low‐frequency (2 Hz) electrical resistivity on 63 sandstone samples with a wide range of petrophysical properties to study the influence of reservoir porosity, permeability and clay content on the joint elastic‐electrical properties of reservoir sandstones. P‐ and S‐wave velocities were found to be linearly correlated with apparent electrical formation factor on a semi‐logarithmic scale for both clean and clay‐rich sandstones; P‐ and S‐wave attenuations showed a bell‐shaped correlation (partial for S‐waves) with apparent electrical formation factor. The joint elastic‐electrical properties provide a way to discriminate between sandstones with similar porosities but with different clay contents. The laboratory results can be used to estimate sandstone reservoir permeability from seismic velocity and apparent formation factor obtained from co‐located seismic and controlled source electromagnetic surveys.  相似文献   

13.
Electromagnetic (EM) logging provides an efficient method for high-resolution, vertical delineation of electrically conductive contamination in glacial sand-and-gravel aquifers. LM. gamma, and lithologic logs and specific conductance data from sand-and-gravel aquifers at five sites in the northeastern United States were analyzed to define the relation of KM conductivity to aquifer lithology and water quality. Municipal waste disposal, septic waste discharge, or highway deicing salt application at these sites has caused contaminant plumes in which the dissolved solids concentration and specific conductance of ground water exceed background levels by as much as 10 to 20 limes.
The major hydrogeologic factors that affected KM log response at the five sites were the dissolved solids concentration of the ground water and the silt and clay content in the aquifer. KM conductivity of sand and gravel with uncontaminated water ranged from less than 5 to about 10 millisiemens per meter (mS/m); that of silt and clay zones ranged from about 15 to 45 mS/m: and that of the more highly contaminated zones in sand and gravel ranged from about 10 to more than 80 mS/m. Specific conductance of water samples from screened intervals in sand and gravel at selected monitoring well installations was significantly correlated with KM conductivity.
CM logging can be used in glacial sand-and-gravel aquifer investigations to (1) determine optimum depths for the placement of monitoring well screens: (2) provide a nearly continuous vertical profile of specific conductance to complement depth-specific water quality samples; and (3) identify temporal changes in water quality through sequential logging. Detailed lithologic or gamma logs, preferably both, need to be collected along with the F.M logs to define zones in which elevated EM conductivity is caused by the presence of sill and clay beds rather than contamination.  相似文献   

14.
This study examined the effects of different soil texture configurations on water movement and solute transport to provide a reliable scientific basis for the application of negative‐pressure irrigation (NPI) technology. HYDRUS‐2D was used to analyse water movement and solute transport under NPI. The main results are as follows: (a) HYDRUS‐2D can be used to simulate water movement and solute transport under NPI, as there was good agreement between the simulated and measured values for water contents, NaCl concentrations, cumulative water infiltration, and wetting distances in the horizontal and vertical directions; the Nash–Sutcliffe efficiency coefficients were in the range of 0.94–0.97. (b) Layered soils have obvious effects on water movement under NPI. With the emitter position in the loam layer, when a coarse texture of loamy sand was present below the loam layer (namely, L‐LS), irrigation water accumulated in the topsoil, and this led to an increase in evaporation compared with the homogeneous loam profile. However, fine texture silty loam or silty clay loam layers beneath the loam layer (namely, L‐SiL or L‐SiCL, respectively) was more conducive to water infiltration into the lower layer, and this increased the amount of water infiltration and simultaneously reduced the surface evaporation effectively. (c) Layered soils have obvious effects on solute transport under NPI, and salt accumulation will readily occur in the clay‐rich soil layer at the interface. The maximum soil salt accumulation of L‐LS occurred above the soil interface between the two soil layers with a value of 21.80 g/kg; however, for L‐SiCL and L‐SiL, the maximum salt accumulation occurred below the soil interface between the two soil layers, with values of 23.80 g/kg and 20.08 g/kg, respectively. (d) Interlayered soils showed remarkable changes in the water infiltration characteristics and salt‐leaching intensities under NPI, and the properties for the soil profile with a silty loam interlayer were better than those for the soil profile with a silty clay loam interlayer. The soil profile with a loamy sand interlayer had the lowest amount of water infiltration, which resulted in reductions of the salt‐leaching intensities. Thus, NPI is clearly not suitable for loamy sand soil. Overall, the results demonstrated that soil texture configurations affected water movement and solute transport under NPI. Therefore, careful consideration should be given to the use of NPI to achieve target soil water and solution conditions and reduce water loss.  相似文献   

15.
We performed quasi‐two‐dimensional flow through laboratory experiments to study the effect of a coarse‐material inclusion, located in the proximity of the water table, on flow and oxygen transfer in the capillary fringe. The experiments investigate different phases of mass transfer from the unsaturated zone to anoxic groundwater under both steady‐state and transient flow conditions, the latter obtained by fluctuating the water table. Monitoring of flow and transport in the different experimental phases was performed by visual inspection of the complex flow field using a dye tracer solution, measurement of oxygen profiles across the capillary fringe, and determination of oxygen fluxes in the effluent of the flow‐through chamber. Our results show significant effects of the coarse‐material inclusion on oxygen transfer during the different phases of the experiments. At steady state, the oxygen flux across the unsaturated/saturated interface was considerably enhanced due to flow focusing in the fully water‐saturated coarse‐material inclusion. During drainage, a zone of higher water saturation formed in the fine material overlying the coarse lens. The entrapped oxygen‐rich aqueous phase contributed to the total amount of oxygen supplied to the system when the water table was raised back to its initial level. In case of imbibition, pronounced air entrapment occurred in the coarse lens, causing oxygen to partition between the aqueous and gaseous phases. The oxygen mass supplied to the anoxic groundwater following the imbibition event was found to be remarkably higher (approximately seven times) in the heterogeneous system compared with a similar experiment performed in a homogeneous porous medium.  相似文献   

16.
The use of surfactant solutions for the in situ recovery of residual NAPL in aquifers is increasingly considered as a viable remediation technique. The injection of a few pore volumes of high concentration surfactant solutions can mobilize most of the residual NAPL contacted by the solutions. However, the washing solutions'physico-chemical properties (low density and high viscosity), combined with the natural porous media heterogeneity, can prevent a good sweep of the entire contaminated volume. From the petroleum industry, it is well-known that polymer solutions can be injected following a surfactant solution slug to act as a mobility buffer and increase the overall sweep efficiency. The objective of our laboratory study is first to select and characterize polymers that would be suitable for aquifer restoration. Our experiments showed that among several polymers, xanthan gum solution rheology was made in order to predict shear rates, xanthan gum concentrations, salinity, and temperature effects on solution viscosity. The second set of experiments were made with a sand box which was designed to reproduce a simple heterogeneous media consisting of layers of sand with different permeability. These tests illustrate the xanthan gum solution's ability to increase surfactant solution's sweep efficiency and limit viscous fingering. The tests established that: (1) the injection of xanthan solution behind a surfactant solution slug decreases fluid velocity in high permeability layers and increases it in low-permeability ones, thus increasing the sweep efficiency (2) xanthan solutions eliminate viscous fingering at the polymer/surfactant solution front; (3) a xanthan solution preflush is desirable to limit surfactant solution mobility and prevent surfactant adsorption on solids; and (4) depending on site heterogeneity injection strategies should be applied to limit overriding by low-density surfactant solution.  相似文献   

17.
Dunn AM  Silliman SE 《Ground water》2003,41(6):729-734
A laboratory tank was used to study entrapment of water in coarse sand lenses above the water table and of air in coarse sand lenses below the water table. Monitoring of these experiments involved a combination of visual inspection, measurement of moisture content, and measurement of air/water pressure. The medium consisted of coarse sand lenses with various degrees of vertical connectivity embedded within a fine sand matrix. Experiments were performed under conditions of both drainage (from a fully saturated medium) and imbibition. Observations during drainage included: (1) water was trapped in the coarse sand zones above the water table at heights significantly greater than anticipated from consideration of capillary rise in the coarse sand; (2) rapid drainage of these same coarse zones occurred when air penetrated into these zones through the surrounding fine sands; and (3) prior to the time of penetration of the coarse sand by air, water pressure in the coarse zone dropped significantly below atmospheric pressure. Observations during imbibition included: (1) entrapment of air within coarse sands below the water table, (2) the pore fluids in these zones varied spatially from predominantly air to predominantly water, and (3) pressure in the trapped air phase was significantly greater than pressure in the water phase in the surrounding fine sand. Overall, these results demonstrated significant sensitivity to the geometry of the coarse sand inclusions, particularly the vertical connectivity of the coarse sand lens.  相似文献   

18.
Sand lenses at various spatial scales are recognized to add heterogeneity to glacial sediments. They have high hydraulic conductivities relative to the surrounding till matrix and may affect the advective transport of water and contaminants in clayey till settings. Sand lenses were investigated on till outcrops producing binary images of geological cross‐sections capturing the size, shape and distribution of individual features. Sand lenses occur as elongated, anisotropic geobodies that vary in size and extent. Besides, sand lenses show strong non‐stationary patterns on section images that hamper subsequent simulation. Transition probability (TP) and multiple‐point statistics (MPS) were employed to simulate sand lens heterogeneity. We used one cross‐section to parameterize the spatial correlation and a second, parallel section as a reference: it allowed testing the quality of the simulations as a function of the amount of conditioning data under realistic conditions. The performance of the simulations was evaluated on the faithful reproduction of the specific geological structure caused by sand lenses. Multiple‐point statistics offer a better reproduction of sand lens geometry. However, two‐dimensional training images acquired by outcrop mapping are of limited use to generate three‐dimensional realizations with MPS. One can use a technique that consists in splitting the 3D domain into a set of slices in various directions that are sequentially simulated and reassembled into a 3D block. The identification of flow paths through a network of elongated sand lenses and the impact on the equivalent permeability in tills are essential to perform solute transport modeling in the low‐permeability sediments.  相似文献   

19.
The determination of clay content in near‐surface formations is crucial for geotechnical, hydrogeological and oil‐contamination studies. We have developed a technique for estimating clay content that consists of the minimization of the difference between the theoretically calculated and measured soil resistivities as a function of water salinity. To calculate the resistivity, we used a model that takes into account the electrochemical processes in the clay micropores. The experimental measurements of soil resistivity were performed on soil samples, completely saturated by brines at different concentrations of NaCl salt in the range 0.6–100 g/l, to obtain the resistivity versus salinity curve. The parameters obtained with this curve inversion are the clay content, the total porosity and the cation exchange capacity. To verify the new technique, we determined clay concentrations of artificial mixtures of calibrated sand and clay. The relative mean error in the clay content does not exceed 20% for a 5% fitting error of the resistivity versus salinity curves. Such evaluations allow the correct separation of the main lithological groups (sand, sandy loam, loam, and light, medium and heavy clay). We applied this technique to estimate the petrophysical parameters of soils (clay content, porosity and cation exchange capacity) at various sites in Mexico. The results improved the interpretation of the vertical electrical soundings, the lithological soil characterization and the delineation of oil‐contaminated areas.  相似文献   

20.
Field investigations were carried out to determine the occurrence of tetrachloroethene (PCE) dense nonaqueous phase liquid (DNAPL), the source zone architecture and the aquitard integrity at a 30‐ to 50‐year old DNAPL release site. The DNAPL source zone is located in the clay till unit overlying a limestone aquifer. The DNAPL source zone architecture was investigated through a multiple‐lines‐of‐evidence approach using various characterization tools; the most favorable combination of tools for the DNAPL characterization was geophysical investigations, membrane interface probe, core subsampling with quantification of chlorinated solvents, hydrophobic dye test with Sudan IV, and Flexible Liner Underground Technologies (FLUTe) NAPL liners with activated carbon felt (FACT). While the occurrence of DNAPL was best determined by quantification of chlorinated solvents in soil samples supported by the hydrophobic dye tests (Sudan IV and NAPL FLUTe), the conceptual understanding of source zone architecture was greatly assisted by the indirect continuous characterization tools. Although mobile or high residual DNAPL (S t > 1%) only occurred in 11% of the source zone samples (intact cores), they comprised 86% of the total PCE mass. The dataset, and associated data analysis, supported vertical migration of DNAPL through fractures in the upper part of the clay till, horizontal migration along high permeability features around the redox boundary in the clay till, and to some extent vertical migration through the fractures in the reduced part of the clay till aquitard to the underlying limestone aquifer. The aquitard integrity to DNAPL migration was found to be compromised at a thickness of reduced clay till of less than 2 m.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号