首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献，搜索用时 414 毫秒
1.
Laboratory evaluations of flowmeter response to flow in fractured-rock simulators are needed to improve understanding of data collected in field settings. The ability of flowmeters to accurately measure the velocity and direction of water flowing between parallel plates was used as a surrogate for instrument response in fractured-rock aquifers. A colloidal borescope flowmeter and a heat-pulse flowmeter were deployed in a fractured rock simulator with 4-inch and 6-inch inner-diameter, uncased wells with 0.39- and 1.0-inch fracture apertures and groundwater velocities from 35 to 975 ft/d. The colloidal borescope measurements and applied velocities were positively correlated in all wells and apertures (the coefficient of determination [r2] = 0.61–0.89) and most accurately measured direction at higher velocities. The mean directional error in colloidal borescope measurements was less than 17° in 6-inch wells and 31° in the 4-inch wells at velocities between 92 and 958 ft/d. Heat-pulse flowmeter measurements were 0.001 to 0.004 times less than applied rates and may indicate that water was moving around rather than through the instrument's integrated packer. The mean directional error of heat-pulse flowmeter measurements were about 18 and 42° in the 0.39- and 1.0-inch fractures, respectively, for groundwater velocities within the manufacturer's suggested range of application (0.5–100 ft/d). Measurements made at vertical increments and fracture positions in the well using the colloidal borescope indicate that laminar flow occurs within the central 50% of the fracture but measurements above or below are likely affected by eddy currents.  相似文献   

2.
Borehole flowmeters that measure horizontal flow velocity and direction of groundwater flow are being increasingly applied to a wide variety of environmental problems. This study was carried out to evaluate the measurement accuracy of several types of flowmeters in an unconsolidated aquifer simulator. Flowmeter response to hydraulic gradient, aquifer properties, and well‐screen construction was measured during 2003 and 2005 at the U.S. Geological Survey Hydrologic Instrumentation Facility in Bay St. Louis, Mississippi. The flowmeters tested included a commercially available heat‐pulse flowmeter, an acoustic Doppler flowmeter, a scanning colloidal borescope flowmeter, and a fluid‐conductivity logging system. Results of the study indicated that at least one flowmeter was capable of measuring borehole flow velocity and direction in most simulated conditions. The mean error in direction measurements ranged from 15.1° to 23.5° and the directional accuracy of all tested flowmeters improved with increasing hydraulic gradient. The range of Darcy velocities examined in this study ranged 4.3 to 155 ft/d. For many plots comparing the simulated and measured Darcy velocity, the squared correlation coefficient (r2) exceeded 0.92. The accuracy of velocity measurements varied with well construction and velocity magnitude. The use of horizontal flowmeters in environmental studies appears promising but applications may require more than one type of flowmeter to span the range of conditions encountered in the field. Interpreting flowmeter data from field settings may be complicated by geologic heterogeneity, preferential flow, vertical flow, constricted screen openings, and nonoptimal screen orientation.  相似文献   

3.
Currently, monitoring tools can be deployed in observation boreholes to better assess groundwater flow, flux of dissolved contaminants and their mass discharge in an aquifer. The relationship between horizontal water velocity in observation boreholes and Darcy fluxes in the surrounding aquifer has been studied for natural flow conditions (i.e., no pumping). Interpretation of measurements taken with dilution tests, the colloidal borescope, the Heat Pulse Flowmeter, and other techniques require the conversion of observed borehole velocity u to aquifer Darcy flux q∞ . This conversion is typically done through a proportionality factor α = u/q∞ . In experimental studies as well as in theoretical developments, reported values of α vary almost three orders of magnitude (from 0.5 to 10). This large variability in reported values of α could be explained by: (1) unclear distinction between Darcy flux and water seepage velocity, (2) unclear definition of water velocity in the borehole, (3) effects of well screen and the presence of the measurement device itself on the observable velocities, and (4) hydraulic conditions in the borehole annulus. We address (1), (2) from a conceptual/theoretical perspective, and (3) by means of numerical simulations. We show that issue (1) in low porosity aquifers can yield to order-of-magnitude discrepancies in estimates of q∞ ; (2) may result in discrepancies of up to 50%, and (3) can cause differences up to 20% of water velocity in the borehole void space compared to the theoretical case of an open borehole.  相似文献   

4.
  相似文献   

5.
The parallel physically-based surface–subsurface model PARFLOW was used to investigate the spatial patterns and temporal dynamics of river–aquifer exchange in a heterogeneous alluvial river–aquifer system with deep water table. Aquifer heterogeneity at two scales was incorporated into the model. The architecture of the alluvial hydrofacies was represented based on conditioned geostatistical indicator simulations. Subscale variability of hydraulic conductivities (K) within hydrofacies bodies was created with a parallel Gaussian simulation. The effects of subscale heterogeneity were investigated in a Monte Carlo framework. Dynamics and patterns of river–aquifer exchange were simulated for a 30-day flow event. Simulation results show the rapid formation of saturated connections between the river channel and the deep water table at preferential flow zones that are characterized by high conductivity hydrofacies. Where the river intersects low conductivity hydrofacies shallow perched saturated zones immediately below the river form, but seepage to the deep water table remains unsaturated and seepage rates are low. Preferential flow zones, although only taking up around 50% of the river channel, account for more than 98% of total seepage. Groundwater recharge is most efficiently realized through these zones. Subscale variability of Ksat slightly increased seepage volumes, but did not change the general seepage patterns (preferential flow zones versus perched zones). Overall it is concluded that typical alluvial heterogeneity (hydrofacies architecture) is an important control of river–aquifer exchange in rivers overlying deep water tables. Simulated patterns and dynamics are in line with field observations and results from previous modeling studies using simpler models. Alluvial heterogeneity results in distinct patterns and dynamics of river–aquifer exchange with implications for groundwater recharge and the management of riparian zones (e.g. river channel-floodplain connectivity via saturated zones).  相似文献   

6.
The hydrological influence of fault zones in tectonic areas is usually difficult to depict from field data. Numerical simulation allows representation of such flow systems and an estimation of flow lines and rates. This paper reports on simulations of the groundwater flow in a range‐and‐basin area affected by a regional fault zone, which may drain or recharge an overlaying alluvial aquifer. Different hydraulic conductivity values for the range rocks, the fault‐zone, and the sedimentary infill of the basin are considered, as well as different fault‐zone widths and boundary conditions. Results show that upward and downward fluxes develop in the upper part of the fault zone, controlled by the action of the alluvial aquifer, influencing the recharge of the sedimentary basin. This paper shows the hydrological efficiency of fault zones as preferential flow; it also analyses the constraints that determine groundwater recharge to the surrounding basins. These results contribute to the understanding of hydrogeological dynamics in tectonic areas. Copyright © 2008 John Wiley & Sons, Ltd.  相似文献   

7.
Abstract

The distribution of major geological units, static water level data, water chemistry data, and observations of surface features influenced by groundwater seepage were used to ascertain the nature of groundwater occurrence and flow pattern in the Enugu coal field, Nigeria. Considerations of the geological units, the static groundwater levels and groundwater seepages in the mines indicate that the coal sequence is a multiaquifer system in which sandstone and coal aquifers alternate with shale aquitards. Based on the hydraulic head data, the groundwater flow is predominantly downwards. Groundwater velocity calculation across the multiaquifer system using the Darcy equation gave a flow velocity of about 1 m day?1. For groundwater systems, such a calculated velocity is considered high. The high velocity is most probably due to the high fracture porosity as well as the presence of other stratigraphic and structural features such as alluvial fills that provide high hydraulic conductivity pathways across the aquifer system. The pattern of groundwater inflow into the mines is also influenced by these stratigraphie and structural features.  相似文献   

8.
A hydrogeophysical survey is performed at small earthen dam that overlies a confined aquifer. The structure of the dam has not shown evidence of anomalous seepage internally or through the foundation prior to the survey. However, the surface topography is mounded in a localized zone 150 m downstream, and groundwater discharges from this zone periodically when the reservoir storage is maximum. We use self‐potential and electrical resistivity tomography surveys with seismic refraction tomography to (1) determine what underlying hydrogeologic factors, if any, have contributed to the successful long‐term operation of the dam without apparent indicators of anomalous seepage through its core and foundation; and (2) investigate the hydraulic connection between the reservoir and the seepage zone to determine whether there exists a potential for this success to be undermined. Geophysical data are informed by hydraulic and geotechnical borehole data. Seismic refraction tomography is performed to determine the geometry of the phreatic surface. The hydro‐stratigraphy is mapped with the resistivity data and groundwater flow patterns are determined with self‐potential data. A self‐potential model is constructed to represent a perpendicular profile extending out from the maximum cross‐section of the dam, and self‐potential data are inverted to recover the groundwater velocity field. The groundwater flow pattern through the aquifer is controlled by the bedrock topography and a preferential flow pathway exists beneath the dam. It corresponds to a sandy‐gravel layer connecting the reservoir to the downstream seepage zone.  相似文献   

9.
A permanent geoelectrical subsurface imaging system has been installed at a contaminated land site to monitor changes in groundwater quality after the completion of a remediation programme. Since the resistivities of earth materials are sensitive to the presence of contaminants and their break-down products, 4-dimensional resistivity imaging can act as a surrogate monitoring technology for tracking and visualising changes in contaminant concentrations at much higher spatial and temporal resolution than manual intrusive investigations. The test site, a municipal car park built on a former gasworks, had been polluted by a range of polycyclic aromatic hydrocarbons and dissolved phase contaminants. It was designated statutory contaminated land under Part IIA of the UK Environmental Protection Act due to the risk of polluting an underlying minor aquifer. Resistivity monitoring zones were established on the boundaries of the site by installing vertical electrode arrays in purpose-drilled boreholes. After a year of monitoring data had been collected, a tracer test was performed to investigate groundwater flow velocity and to demonstrate rapid volumetric monitoring of natural attenuation processes. A saline tracer was injected into the confined aquifer, and its motion and evolution were visualised directly in high-resolution tomographic images in near real-time. Breakthrough curves were calculated from independent resistivity measurements, and the estimated seepage velocities from the monitoring images and the breakthrough curves were found to be in good agreement with each other and with estimates based on the piezometric gradient and assumed material parameters.  相似文献   

10.
The strategic project of economic development in the Dornogobi Province in Mongolia is dependent on water supply. Thus a comprehensive hydrogeological characterization was focused on the Upper Cretaceous multi-aquifer system north of Sainshand city. A conceptual model was developed to discover the groundwater flow pattern essential to correct the setting of the numerical model of groundwater flow created using MODFLOW to assess the natural recharge of the aquifer. The conceptualization was based on geological and hydrogeological characterization. However, the evaluation of hydrochemistry proved to be the key factor revealing the principal feature of the groundwater flow pattern, which is the presence of preferential flow zones. These zones allow for intensive transfer of relatively fresh Na(Mg,Ca)?HCO3-dominated groundwater into discharge areas, where it leaks into the Quaternary aquifer. The numerical model suggested an enormous natural recharge of 22 100 m3/d, originating in 64% of the preferential flow zones.  相似文献   

11.
Pore water radon (222Rn) distributions from Indian River Lagoon, Florida, are characterized by three zones: a lower zone where pore water 222Rn and sediment-bound radium (226Ra) are in equilibrium and concentration gradients are vertical; a middle zone where 222Rn is in excess of sediment-bound 226Ra and concentration gradients are concave-downward; and an upper zone where 222Rn concentration gradients are nearly vertical. These 222Rn data are simulated in a one-dimensional numerical model including advection, diffusion, and non-local exchange to estimate magnitudes of submarine groundwater discharge components (fresh or marine). The numerical model estimates three parameters, fresh groundwater seepage velocity, irrigation intensity, and irrigation attenuation, using two Monte Carlo (MC) simulations that (1) ensure the minimization algorithm converges on a global minimum of the merit function and the parameter estimates are consistent within this global minimum, and (2) provide 90% confidence intervals on the parameter estimates using the measured 222Rn activity variance. Model estimates of seepage velocities and discharge agree with previous estimates obtained from numerical groundwater flow models and seepage meter measurements and show the fresh water component decreases offshore and varies seasonally by a factor of nine or less. Comparison between the discharge estimates and precipitation patterns suggests a mean residence time in unsaturated and saturated zones on the order of 5 to 7 months. Irrigation rates generally decrease offshore for all sampling periods. The mean irrigation rate is approximately three times greater than the mean seepage velocity although the ranges of irrigation rates and seepage velocities are the same. Possible mechanisms for irrigation include density-driven convection, wave pumping, and bio-irrigation. Simulation of both advection and irrigation allows the separation of submarine groundwater discharge into fresh groundwater and (re)circulated lagoon water.  相似文献   

12.
The Mississippi River Valley Alluvial Aquifer ranks among the most overdrafted aquifers in the United States due to intensive irrigation. Concern over declining water levels has increased focus on understanding the sources of recharge. Numerous oxbow lakes overlie the aquifer that are often considered hydraulically disconnected from the groundwater system due to fine-grained bottom sediments. In the current study, groundwater levels in and around a 445-ha oxbow lake-wetland in Mississippi were monitored for a 2-year period that included an unusually long low-water condition in the lake (>17 months), followed by a high-water event lasting over 4 months before returning to earlier low-water levels. The high-water pulse (>4 m rise) provided a unique opportunity to track the impact in the underlying alluvial aquifer. During low-water conditions, groundwater flowed westward beneath the lake. Following the lake rise, groundwater beneath and near the perimeter responded as quickly as the same day, with more delayed responses moving away from the lake. Within 2 months, a groundwater mound formed near the centre of the oxbow (>3 m increase), with a reversal in the local hydraulic gradient towards the east. Flow returned to a westward gradient when the lake level dropped back below 0.3 m. Analysis of precipitation and nearby river stage could not account for the observed behavior. Recharge to the aquifer is attributed to rising water levels spreading over point bar deposits and into the surrounding forested wetlands where preferential flow pathways are likely to exist due to buried and decomposing tree remains. An earlier study in the wetland demonstrated an increasing redox potential in isolated zones, consistent with the existence of preferential flow pathways through the bottom sediments (Lahiri & Davidson, 2020). Retaining high-water levels in oxbow lakes could be a relatively low-cost water management practice for enhancing aquifer recharge.  相似文献   

13.
This paper reports on experiments and simulations of subsurface flow from a slotted acrylic tube deployed in a sand-tank flow chamber for two different purposes. In the first instance, the slotted tube is used to represent a single fracture intersected by an uncased well. In the second instance, the slotted tube is used to represent a multislot well screen within a porous medium. In both cases, the scanning colloidal borescope flowmeter (SCBFM) measures ground water velocity within the well by imaging colloids traveling through a well to measure their speed and direction. Measurements are compared against model simulations. For the case of a slotted tube representing a single fracture, SCBFM and model results agree with respect to the flow direction and to within a factor of 1.5 for the speed near the well's center. Model and experimental agreement lend confidence that for an uncased well drilled in a fractured-rock medium, a calibrated SCBFM could be used to identify and quantify flowing features. Next, the SCBFM was deployed in a four-column multislotted casing with slots aligned with the flow direction. Another numerical model was developed to estimate the flow field within this well screen to evaluate the potential usefulness of employing the SCBFM in a screened well to estimate flow speed and direction in the surrounding porous medium. Results indicate that if the slots are not aligned with the flow, the SCBFM may only provide order-of-magnitude speed measurements and direction measurements with an uncertainty of approximately +/-25 degrees .  相似文献   

14.
Traditional methods for studying surface water and groundwater interactions have usually been limited to point measurements, such as geochemical sampling and seepage measurement. A new methodology is presented for quantifying groundwater discharge to a river, by using river surface temperature data obtained from airborne thermal infrared remote sensing technology. The Hot Spot Analysis toolkit in ArcGIS was used to calculate the percentage of groundwater discharge to a river relative to the total flow of the river. This methodology was evaluated in the midstream of the Heihe River in the arid and semiarid northwest China. The results show that the percentage of groundwater discharge relative to the total streamflow was as high as 28%, which is in good agreement with the results from previous geochemical studies. The data analysis methodology used in this study is based on the assumption that the river water is fully mixed except in the areas of extremely low flow velocity, which could lead to underestimation of the amount of groundwater discharge. Despite this limitation, this remote sensing‐based approach provides an efficient means of quantifying the surface water and groundwater interactions on a regional scale.  相似文献   

15.
This study addresses the influence of landslide dams on surface water drainage and groundwater flow. In the study area of Scanno Lake and Sagittario River (Central Italy), a limestone rockslide‐avalanche formed a lake, which has an outlet that is occasionally active, showing infiltration into the rockslide dam. Several springs are present at the lake's base and are partly fed by seepage through the rockslide debris. Piezometric surveys, discharge measurements, pumping tests and chemical analyses are tools used to build a conceptual model of the groundwater flow and to evaluate the flow through the rockslide debris. Seasonal water isotopic signatures validate the assumed model, showing a mixing of infiltration recharge and groundwater seepage throughout the rockslide debris. Various recharge areas have been found for springs, pointing out those directly fed by the rockslide debris aquifer. Hypotheses about seasonal groundwater mixing between the regional carbonate aquifer and the rockslide debris aquifer are supported by isotope results. Seasonal changes in groundwater table level due to recharge and surface losses from seasonal outlet have been correlated with isotopic groundwater composition from the rockslide debris aquifer and the downstream springs; this relationship highlights the role of the rockslide dam body on the hydrodynamics of the studied area. Relationships between surface waters and groundwater in the area have been completely understood on the basis of water isotopic fingerprinting, finally obtaining a complete evaluation of groundwater renewable resources and its regimen. Copyright © 2010 John Wiley & Sons, Ltd.  相似文献   

16.
A transient axisymmetric saturated-unsaturated numerical flow model was coupled with a particle tracking model to investigate the movement of contaminants when a shallow unconfined aquifer is pumped at a constant rate. The particle tracking model keeps track of locations and masses of solutes in the aquifer, and the time of capture by the well. At the end of each time-step the flow model solves the Richard's equation for the hydraulic head distribution from which elemental velocities are calculated. Solutes are then displaced for a period equivalent to the time-step using both the magnitude and direction of the elemental velocities. Numerical experiments were performed to investigate effluent concentrations in wells with screens of different length and in different positions relative to zones of stratified contamination. At early times of pumping the effluent concentrations were similar to the concentrations adjacent to the well screen, but at late times, the concentrations approached the vertically averaged concentration in the aquifer. Time to attain the vertically averaged concentration was determined by the well geometry, initial location of the contaminant plume in relation to the well screen, and hydraulic properties of the aquifer. The results are consistent with the hydraulics of flow to a pumping well and of particular importance, they demonstrate that short-term pump tests could give erroneous design concentrations for pump-and-treat systems. The model provides a means of quantifying arrival times and mixing ratios. It could therefore provide a useful means of designing production wells in aquifers with stratified contamination and more efficient recovery systems for aquifer remediation.  相似文献   

17.
Unlike rivers in humid regions, dryland rivers typically exhibit reduced flow in the downstream direction as a result of transmission losses, which include seepage of streamflow into the aquifer, evaporation, and transpiration. However, much remains to be learned about the nature of the exchange between surface water and groundwater in these landscapes, especially in terms of spatial and temporal variability. Our study focused on streambank seepage and groundwater flow in the alluvial aquifer, specifically on answering questions such as: Is there seasonal variability in seepage losses? Is seepage permanently lost? Can losses be reduced by killing riparian vegetation? To better understand the magnitude, variability, and fate of streambank seepage, we assessed river stages, groundwater hydraulic gradients, and groundwater flow paths at two sites along a reach of the Pecos River, a dryland perennial river in West Texas. We found that along this reach the river was losing water to the aquifer even under low‐flow conditions; but seepage was controlled by a number of different mechanisms. Seepage increased not only during high‐flow events but also when the groundwater level was declining owing to long periods of no irrigation release. Tamarix (saltcedar) control did not affect hydraulic gradients nor reduce streambank seepage and given that this reach of the Pecos River is a losing one, streamflow will not be enhanced by controlling saltcedar. These findings can be used to improve basic conceptual models of dryland river systems and to predict hydrologic responses to changes in the timing and magnitude of streamflows and to riparian vegetation management. Copyright © 2012 John Wiley & Sons, Ltd.  相似文献   

18.
The article presents semi‐analytical mathematical models to asses (1) enhancements of seepage from a canal and (2) induced flow from a partially penetrating river in an unconfined aquifer consequent to groundwater withdrawal in a well field in the vicinity of the river and canal. The nonlinear exponential relation between seepage from a canal reach and hydraulic head in the aquifer beneath the canal reach is used for quantifying seepage from the canal reach. Hantush's (1967) basic solution for water table rise due to recharge from a rectangular spreading basin in absence of pumping well is used for generating unit pulse response function coefficients for water table rise in the aquifer. Duhamel's convolution theory and method of superposition are applied to obtain water table position due to pumping and recharge from different canal reaches. Hunt's (1999) basic solution for river depletion due to constant pumping from a well in the vicinity of a partially penetrating river is used to generate unit pulse response function coefficients. Applying convolution technique and superposition, treating the recharge from canal reaches as recharge through conceptual injection wells, river depletion consequent to variable pumping and recharge is quantified. The integrated model is applied to a case study in Haridwar (India). The well field consists of 22 pumping wells located in the vicinity of a perennial river and a canal network. The river bank filtrate portion consequent to pumping is quantified.  相似文献   

19.
The objective of this article is to analyze the influence of clay zones on subsidence from groundwater pumping. Finite element analyses were conducted on a sand‐only aquifer and a sand aquifer with two clay zones located at different distances from the well face. A model that accounts for recoverable and nonrecoverable strains was used to simulate the sand and clay. This model couples the groundwater flow with the stress‐deformation response of the aquifer materials. Each aquifer was pumped from a single well for a period of 6 months, and then the groundwater level was lowered gradually to an elevation below the elevation of the clay zones and kept there for 10 years. The groundwater level was then raised gradually back to the original elevation over a period of 10 years. The results of the analyses show that the ground surface subsidence profile is strongly influenced by the presence of the clays zones. The ground surface sags where these clay zones are present resulting in a wavy ground surface profile. Subsidence continued when pumping is stopped, albeit at a much slower rate than during pumping, and when the groundwater level is below the elevation of the clay zones. Clay zones further away from the well face lag the subsidence of clay zones nearer the well face because of lower changes in hydrostatic head. Sags in ground surface subsidence profile from groundwater pumping are indicators of the presence of low hydraulic conductive geological materials.  相似文献   

20.
An analytical solution for the space-time variation of contaminant concentration in one-dimensional transient groundwater flow in a homogenous semi-infinite aquifer, subjected to time-dependent source contamination, is derived. The uniform and time varying dispersion along transient groundwater flow is investigated under two conditions. First, the flow velocity distribution in the aquifer is considered as a sinusoidally varying function, and second, the flow velocity distribution is treated as an exponentially increasing function of time. It is assumed that initially the aquifer is not solute free, so the initial background concentration is considered as an exponentially decreasing function of the space variable which is tending to zero at infinity. It is assumed that dispersion is directly proportional to the square of the velocity, noting that experimental observations indicate that dispersion is directly proportional to the velocity with a power ranging from 1 to 2. The analytical solution is illustrated using an example and may help benchmark numerical codes and solutions.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号