共查询到20条相似文献，搜索用时 328 毫秒
1.
The experimental and theoretical investigations on the behaviour of pontoon-type floating breakwaters are presented. A two-dimensional finite element model is adopted to study the behaviour of pontoon-type floating breakwaters in beam waves. The stiffness coefficients of the slack mooring lines are idealized as the linear stiffness coefficients, which can be derived from the basic catenary equations of the cable. The theoretical model is supported by an experimental programme conducted in a wave flume. The motion responses and mooring forces are measured for three different mooring configurations, and the results are reported and discussed in detail in this paper. The wave attenuation characteristics are presented for the configurations studied. 相似文献
2.
In recent years floating breakwaters are considered for creating calm basin under open sea conditions for short period of time. In this paper, experimental studies on the performance characteristics of a horizontal floating plate breakwater are presented. The results of this two-dimensional model study are for regular waves of shallow and intermediate water depths. Analysis of the results shows that the transmission coefficient is strongly influenced by wave steepness and relative length of breakwater. It is also found to be dependent, to a lesser extent, on the relative depth of draft. Mooring forces are found to increase with increasing wave steepness and relative depth of draft. The performance of this breakwater is compared with other types of breakwater reported by earlier workers. 相似文献
3.
Ioanna Diamantoulaki Demos C. Angelides George D. Manolis 《Applied Ocean Research》2008,30(4):243-255
The overall performance of pile-restrained flexible floating breakwaters is investigated under the action of linear monochromatic incident waves in the frequency domain. The aforementioned floating breakwaters undergo only vertical structural deflections along their length and are held in place by means of vertical piles. The total number of degrees of freedom equals the six conventional body modes, when the breakwater moves as a rigid body, plus the extra bending modes. These bending modes are introduced to represent the structural deflections of the floating breakwater and are described by the Bernoulli–Euler flexible beam equation. The number of bending modes introduced is determined through an appropriate iterative procedure. The hydrostatic coefficients corresponding to the bending modes are also derived. The numerical analysis of the flexible floating breakwaters is based on a three-dimensional hydrodynamic formulation of the floating body. A parametric study is carried out for a wide range of structural stiffness parameters and wave headings, to investigate their effect on the performance of flexible floating breakwaters. Moreover, this performance is compared with that of the corresponding pile-restrained rigid floating breakwater. Results indicated that the degree of structural stiffness and the wave heading strongly affect the performance of flexible floating breakwaters. The existence of an “optimum” value of structural stiffness is demonstrated for the entire wave frequency range. 相似文献
4.
5.
The ocean wave system in nature is very complicated and physical model studies on floating breakwaters are expensive and time consuming. Till now, there has not been available a simple mathematical model to predict the wave transmission through floating breakwaters by considering all the boundary conditions. This is due to complexity and vagueness associated with many of the governing variables and their effects on the performance of breakwater. In the present paper, Adaptive Neuro-Fuzzy Inference System (ANFIS), an implementation of a representative fuzzy inference system using a back-propagation neural network-like structure, with limited mathematical representation of the system, is developed. An ANFIS is trained on the data set obtained from experimental wave transmission of horizontally interlaced multilayer moored floating pipe breakwater using regular wave flume at Marine Structure Laboratory, National Institute of Technology Karnataka, Surathkal, India. Computer simulations conducted on this data shows the effectiveness of the approach in terms of statistical measures, such as correlation coefficient, root-mean-square error and scatter index. Influence of input parameters is assessed using the principal component analysis. Also results of ANFIS models are compared with that of artificial neural network models. 相似文献
6.
Geotextile Sand Containers (GSC) are increasingly used worldwide for shore protection structures such as seawalls, groins, breakwaters, revetments and artificial reefs. However, reliable design formulae for the hydraulic stability based on a good understanding of the processes involved in the wave-structure interactions are still needed.Although the effect of the deformations of the sand containers on the hydraulic stability is significant, no stability formula is available to account for those deformations and the associated processes leading to the observed failures. Therefore, based on the results of extensive experimental and numerical studies ([Recio J. 2008, Hydraulic Stability of Geotextile Sand Containers for Coastal Structures – Effect of Deformations and Stability Formulae – PhD Thesis, Leichtweiss Institute for Hydraulic Engineering and Water Resources, www.digibib.tu-bs.de/?docid=00021899]), analytical stability formulae are developed that account for the effect of the deformations of the individual GSCs for sliding and overturning stability. The required drag, inertia and lift coefficients are determined experimentally from hydraulic model experiments specially designed for this purpose. Several types of GSC configurations which are representative for a wide range of GSC-structure types are investigated under wave action. Moreover, deformation factors to account for the deformation of the containers on the stability are analytically derived and implemented in the stability formulae.Finally, Stability formulae for each type of coastal structures made of geotextile sand containers such as breakwaters, revetments, sea walls, dune reinforcement and scour protection systems are proposed and recommendations are given with respect to the practical application of the proposed hydraulic stability formula, including their limitations. 相似文献
7.
Bragg reflection of water waves by multiple floating horizontal flexible membranes is investigated based on the linear wave theory and the assumption of small membrane response. Under the floating horizontal membranes, periodical submerged rectangular bars are arranged on the flat seabed. The total reflection and transmission coefficients are obtained by using the eigenfunction expansion method and the wide spacing approximation. The calculated coefficients are validated with the results available in the literature, which shows that the present method is applicable. The characteristics of Bragg reflection are systematically investigated by changing various parameters including the height of the rectangular bars, the number, the tension, the spacing, and the length of the flexible membranes. The results can help designing multiple floating horizontal flexible membranes as effective floating breakwaters by taking advantage of Bragg reflection. 相似文献
8.
1 .IntroductionInrecent years ,especiallyfrom1994 when aninternational conference on breakwater design washeldinJapan,muchresearchonthe dynamic analysis of caisson breakwaters has been done ,and manyimportant progresses have been made .Oumeraci and Korten… 相似文献
9.
To find a simple, inexpensive, and effective type of floating breakwater for deep-sea aquaculture, we studied three types of structures: the single box, the double box, and the board net. We conducted two-dimensional physical model tests in a wave-current flume in the laboratory to measure the wave transmission coefficients of the three types of breakwaters under regular waves with or without currents. Based on the initial comparison of the wave transmission coefficients, we proposed the use of the board-net floating breakwater for use with fish cages; we then conducted detailed experiments to examine how wave transmission coefficients are affected by several factors, including the width of the board, the row number of the net, the rigidity of the board, and the current velocity. The experimental results show that the board-net floating breakwater, which is a simple and inexpensive type of structure, can effectively protect fish and fish cages and may be adopted for aquaculture engineering in deep-water regions. 相似文献
10.
This paper presents the results and conclusions obtained from the physical model tests carried out with four different designs of floating breakwaters. Changes from a basic design have been introduced in order to evaluate the improvement in the efficiency as a coastal protection structure. Incident and transmitted waves have been measured, as well as the efforts in the mooring lines and module connectors. It has been found that the width of the pontoons is one of the key design parameters, while small modifications in the floating breakwater's cross section shape are less determinant in its hydrodynamic behaviour and in mechanical loads in the discussed ranges. 2D and 3D tests were conducted, observing the great influence that the wave obliquity has in the module connector forces. 相似文献
11.
Interaction of surface gravity waves with multiple vertically moored surface-piercing membrane breakwaters in finite water depth is analyzed based on the linearized theory of water waves. The study is carried out using least square approximation method to understand the effect of the vertical membrane as effective breakwater. Initially the problem is studied for a single membrane wave barrier but for the case of multiple membrane breakwaters the study is carried out using the method of wide-spacing approximation. In the present study, it is observed that the deflection of the membrane is reduced with the increase in the stiffness parameter of the mooring lines attached to the membrane. In the case of single surface-piercing membrane with moored and fixed edge conditions, the reflection and transmission coefficients are compared and analyzed in detail. The resonating pattern in the reflection coefficients are also observed for multiple floating membrane which can also be referred as Bragg's resonance. In the presence of the porosity constant the wave reflection is also observed to be decreasing and the change in the distance between the vertical floating breakwaters also helps in the attenuation of wave height. It is observed that the presence of multiple floating breakwater helps in the reduction of wave height in the transmitted region. 相似文献
12.
Zhenhua HUANG 《中国海洋工程》2008,22(2):205-214
The adoption of slotted breakwaters can be an ideal option in the protection of very large near-shore floating struc-trees that may extend offshore to a considerable water depth. In this paper, we experimently investigated the behaviour of wave transmission and reflection coefficients of double slotted barriers in the presence of a steady opposing current. The experimental results show that opposing currents have only minor effects on wave reflection, but can significantly reduce the wave transmission through double slotted barriers. The experimental results suggest that coastal currents should be taken into consideration for an economical design of slotted breakwaters. 相似文献
13.
Investigation of the effects of offshore breakwater parameters on sediment accumulation 总被引：1，自引：0，他引：1
Ali Remzi Birben &#x;smail Hakk&#x;
zler Servet Karasu Murat &#x;hsan Kmürcü 《Ocean Engineering》2007,34(2):284-302
Littoral sediment transport is the main reason for coastal erosion and accretion. Therefore, various types of structures are used in shore protection and littoral sediment trapping studies. Offshore breakwaters are one of these structures. Construction of offshore breakwaters is one of the main countermeasures against beach erosion. In this paper, offshore protection process is studied on the effect of offshore breakwater parameters (length, distance and gap), wave parameters (height, period and angle) and on sediment accumulation ratio, one researched in a physical model. In addition to the experimental studies, numerical model in which the formulae of the sediment discharge (i.e. the formulae of CERC and Kamphuis), was used was developed and employed. The results of the experimental and numerical studies were compared with each other. 相似文献
14.
A.N. Williams 《Ocean Engineering》1993,20(3)
A numerical model is developed to investigate the behavior of a pair of flexible, floating breakwaters consisting of complaint, beam-like structures anchored to the sea bed. Each structure is kept under tension by a small buoyancy chamber at the tip, additional stiffness in each case is provided by mooring lines attached to the buoyancy chamber. The fluid motion is idealized as linearized, two-dimensional potential flow and the equation of motion of each breakwater is taken to be that of a one-dimensional beam of uniform flexural rigidity and mass per unit length subjected to a constant axial force. The boundary integral equation method is applied to the fluid domain. Modifications are made to the basic formulation to account for the zero thickness of the idealized structures, and the dynamic behavior of the breakwaters is described through an appropriate Green's function. Numerical results are presented which illustrate the effects of the various wave and structural parameters on the efficiency of the two-breakwater systems as a barrier to wave action. It is found that by adjusting the spacing between the breakwaters acceptable wave reflection characteristics may be obtained even with relatively flexible structures. 相似文献
15.
Hydraulic performance and wave loadings of perforated/slotted coastal structures: A review 总被引：4，自引：0，他引：4
This paper reviews recent progress in the study of perforated/slotted breakwaters, with an emphasis on two main groups of such breakwaters: (1) perforated/slotted breakwaters with impermeable back walls, and (2) perforated/slotted breakwaters without a back-wall. The methods commonly used to simulate the interactions between such structures and various linear/nonlinear waves are summarized. The transmission and reflection characteristics of perforated/slotted breakwaters in these two groups are reviewed extensively. Several methods for calculating wave forces on perforated caissons are also reviewed. Some recent works published in Chinese journals, which are generally not well-known to non-Chinese researchers, are reviewed with a hope that these works can be beneficial to other researchers working in this area. 相似文献
16.
基于成本共享理念的波浪能发电装置(WEC)的开发与设计为降低建设成本提供了新的研究思路,应用计算流体力学方法对在透空箱式防波堤前附加垂荡浮子的集成装置进行数值模拟研究,主要研究了流体黏性和非线性PTO系统以及浮子形状对此类集成装置能量转换效率的影响。结果表明,此类集成装置可以获得较高的波能捕获宽度比(CWR),最高可达0.7,可以较好地利用反射波波能。共振区间上受黏性影响较大,相比于线性无黏理论解,CWR下降明显;实现了2种非线性PTO系统的模拟,有待于进一步的优化未获得更高的CWR值;浮子形状优化效果明显,采用圆底形浮子受黏性影响更小,可以获得更大的CWR值。此种集成模型的模拟和研究可以为新型防波堤设计和现有防波堤的改造提供思路和参考。 相似文献
17.
C.J. Garrison 《Applied Ocean Research》1984,6(1):4-15
A Green's function procedure is applied to compute the oblique wave interaction with a cylinder of arbitrary section on the free surface in water of infinite depth. Also, the hydrodynamic coefficients associated with the motion of the cylinder oscillating in its three degrees of freedom, periodic along its axis, are treated. A computer program based on the present procedure is found to be accurate and efficient. The results are applicable to the analysis of floating breakwaters, floating bridges, ship hulls and other elongated structures on a free surface. 相似文献
18.
Rubble mound breakwaters usually consist of armour, filter and core layers. The units used in the armour layer are natural rock or concrete. Although natural rock is usually preferred, it is not always possible to apply it. There are some advantages to using concrete units: they have a high stability coefficient under wave attack, and they are easily produced at work sites. Tetrapod and cube blocks are widely used in breakwaters as armour units.Rubble mound breakwaters are subjected not only to wave activity but also other types of environmental loading, such as earthquakes. Although rubble-mound breakwaters are most likely the most common type of breakwaters, they have received little attention regarding their response to seismic activity. The objective of this study is to present the dynamic response of a breakwater armoured by tetrapods placed by two different placement methods and armoured by cubes during seismic loadings experimentally and numerically. A shaking tank was developed for the experimental study. The breakwater models sit on a rigid bed, and the model scale is 1/50. A one-dimensional shaking tank was used to understand simple responses of the rubble mound breakwaters under seismic loads. The tank allows only one degree of freedom. A raining crane system was developed to achieve the same packing density and porosity for the core material. The shape of the model breakwater before and after the tests was measured using a profiler and was recorded by computer. However, crest lowering and the level of damage on slopes were determined from profiler records. The dynamic responses of the model breakwaters were also investigated using an image processing technique. For numerical simulation, software using finite element method was used.The results obtained from the experiment and numerical model may help designers build breakwaters armoured by artificial units. 相似文献
19.
针对具有天然岛礁庇护或人工庇护的温和海洋环境,提出了一种混合模块大型浮式结构系统,即水动力性能更优的半潜式模块作为内侧主模块,消波效果更优的箱式模块作为外侧浮式防波模块和波浪能发电模块.波浪能装置利用外侧箱式模块与内侧半潜式模块的相对纵摇运动进行发电.考虑模块间多体水动力耦合效应和连接器机械耦合效应,基于ANSYS-AQWA程序重点研究了典型海况下混合5模块串联浮式结构系统的动力响应特征.结果表明,外侧箱式模块和波浪能发电装置能有效减弱内侧半潜式主模块运动响应、连接器动力响应和系泊缆绳张力,并且提供一定的能源供给.所得研究成果可为模块化超大型浮式结构系统的防波—发电集成系统设计提供参考. 相似文献
20.
Floating pontoon breakwaters 总被引：1，自引：0，他引：1
The hydrodynamic properties of a pair of long floating pontoon breakwaters of rectangular section are investigated theoretically. The structures are partially restrained by linear symmetric moorings fore and aft. The fluid motion is idealized as linearized, two-dimensional potential flow. The breakwater motions are assumed to be two-dimensional, in surge, heave and pitch. The solution for the fluid motion is obtained by the boundary integral equation method using an appropriate Green's function. Numerical results are presented that illustrate the effects of the various wave and structural parameters on the efficiency of the breakwaters as barriers to wave action. It is found that the wave reflection properties of the structures depend strongly on their width, draft and spacing and the mooring line stiffnesses, while their excess buoyancy is of lesser importance. 相似文献