首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献，搜索用时 15 毫秒
1.
This paper presents the predicted flow dynamics from the application of a Reynolds‐averaged Navier–Stokes model to a series of bifurcation geometries with morphologies measured during previous flume experiments. The topography of the bifurcations consists of either plane or bedform‐dominated beds which may or may not possess discordance between the two bifurcation distributaries. Numerical predictions are compared with experimental results to assess the ability of the numerical model to reproduce the division of flow into the bifurcation distributaries. The hydrodynamic model predicts: (1) diverting fluxes in the upstream channel which direct water into the distributaries; (2) super‐elevation of the free surface induced at the bifurcation edge by pressure differences; and (3) counter‐rotating secondary circulation cells which develop upstream of the apex of the bifurcation and move into the downstream channels, with water converging at the surface and diverging at the bed. When bedforms are not present, weak transversal fluxes characterize the upstream channel for almost its entire length, associated with clearly distinguishable secondary circulation cells, although these may be under‐estimated by the turbulence model used in the solution. In the bedform dominated case, the same hydrodynamic conditions were not observed, with the bifurcation influence restricted and depth scale secondary circulation cells not forming. The results also demonstrate the dominant effect bed discordance has upon flow division between the two distributaries. Finally, results indicate that in bedform dominated rivers. Consequently, we suggest that sand‐bed river bifurcations are more likely to have an influence that extends much further upstream and have a greater impact upon water distribution. This may contribute to observed morphological differences between sand‐bedded and gravel‐bedded braided river networks. Copyright © 2012 John Wiley & Sons, Ltd.  相似文献   

2.
Morphodynamics in sand‐bed braided rivers are associated with simultaneous evolution of mid‐channel bars and channels on the braidplain. Bifurcations around mid‐channel bars are key elements that divide discharge and sediment. This, in turn, may control the evolution of connected branches, with effects propagating to both upstream and downstream bifurcations. Recent works on bifurcation stability and development hypothesize major roles of secondary flow and gradient advantage. However, this has not been tested for channel networks within a fully developed dynamic braided river. A reason for this is a lack of detailed measurements with sufficient temporal and spatial length, covering multiple bifurcations. Therefore we used a physics‐based numerical model to generate a dataset of bathymetry, flow and sediment transport of an 80 km river reach with self‐formed braid bars and bifurcations. The study shows that bar dissection due to local transverse water surface gradients is the dominant bifurcation initiation mechanism, although conversion of unit bars into compound bars dominates in the initial stage of a braided river. Several bifurcation closure mechanisms are equally important. Furthermore, the study showed that nodal point relations for bifurcations are unable to predict short‐term bifurcation evolution in a braided river. This is explained by occurrence of nonlinear processes and non‐uniformity within the branches, in particular migrating bars and larger‐scale backwater‐effects, which are not included in the nodal point relations. Planform morphology, on the other hand, has predictive capacity: bifurcation angle asymmetry and bar‐tail limb shape are indicators for near‐future bifurcation evolution. Remote sensing data has predictive value, for which we developed a conceptual model for interactions between bars, bifurcations and channels in the network. We conducted a preliminary test of the conceptual model on satellite images of the Brahmaputra. Copyright © 2015 John Wiley & Sons, Ltd.  相似文献   

3.
This study presents the first detailed field‐based analysis of the morphology of bifurcations within anabranching cobble–gravel rivers. Bifurcations divide the flow of water and sediment into downstream anabranches, thereby influencing the characteristics of the anabranches and the longevity of river islands. The history, morphology, bed grain size, and flow vectors at five bifurcations on the Renous River, New Brunswick, Canada, were studied in detail. The angles of bifurcations within five anabranching rivers in the Miramichi basin were investigated. The average bifurcation angle was 47°, within the range of values cited for braided river bifurcations. Bifurcation angle decreased when anabranches were of similar length. Shields stresses in channels upstream of bifurcations were lower than reported values for braided rivers. Stable bifurcations displayed lower Shields stresses than unstable bifurcations, contrary to experimental results from braided river bifurcations. Bifurcations in anabranching rivers are stabilized by vegetation that slows channel migration and helps to maintain a uniform upstream flow field. The morphology of stable bifurcations enhances their stability. A large bar, shaped like a shallow ramp that increases in elevation to floodplain level, forms at stable bifurcations. Floodplains at stable bifurcations accrete upstream at rates between 0·9 and 2·5 m a?1. Bars may also form within the entrance of an anabranch downstream of the bifurcation node. These bars are associated with bifurcation instability, forming after a period of stability or an avulsion. Channel abandonment occurs when a bar completely blocks the entrance to one anabranch. The stability of channels upstream of bifurcations and the location of bars at bifurcations influence bifurcation stability and the maintenance of river anabranching in the long term. Copyright © 2006 John Wiley & Sons, Ltd.  相似文献   

4.
Channel bifurcation is a key element in braided rivers, determining the water and sediment distribution and hence controlling the morphological evolution. Recent theoretical and experimental findings, as well as field observations, showed that bifurcations in gravel‐bed braided rivers are often asymmetrical and highly unstable. In this paper field data are presented on a bifurcation in the Tagliamento River, northeast Italy. The planform configuration of the bifurcation and its temporal evolution was monitored by an automatic digital camera during a series of seven floods with different magnitudes. This remote sensing technique allowed a high temporal resolution (pictures were acquired every hour) that was proved to be essential in a highly dynamic system as the one considered here. Digitized maps of the channels provided information on the location of the bifurcation, the width of the anabranches, the angle between them, along with the occurrence and migration of sediment bars. Data were acquired at two different water levels, giving the possibility to compare low and high flow conditions. The monitored bifurcation is largely unstable and shows sudden changes in the water distribution, mainly driven by the bar migrating in the upstream channel and entering the distributaries. A relationship between width asymmetry and flood magnitude was observed, confirming previous analyses. Moreover, recent theoretical findings were applied, in order to test the possibility to estimate general trends in bifurcation evolution. The analysis pointed out the relevance of a correct assessment of the characteristic temporal scales, as the bifurcation evolves on a timescale similar to that of bar migration and flood duration. Understanding the interactions between these processes is therefore crucial in order to increase the ability to model and predict the morphological evolution of a braided network. Copyright © 2012 John Wiley & Sons, Ltd.  相似文献   

5.
Flow dynamics in a bedrock-influenced river system, the Sabie River, South Africa, have been found to be significantly different from those in temperate alluvial systems. The lack of lateral water connectivity leads to multiple bedrock distributaries with varying water surface elevations across a cross-section. Distributary activation is dependent on upstream breaching of bedrock barriers between distributaries by rising discharge. Where measurement of individual stage–discharge relationships in each distributary was not possible, a ‘Multiple Stage’ model was developed to predict hydraulic conditions in each distributary, using a single measured rating curve and knowledge of individual distributary water surface elevations at a low flow. Use of the ‘Multiple Stage’ model has enabled realistic prediction of channel geometry and hydraulic variables, that accounts for the different stages found in bedrock-influenced sections, yet is not prohibitively data intensive. Predicted ‘Multiple Stage’ results for maximum depth and velocity demonstrate the vast improvement on modelling flow dynamics, when compared to the conventional assumption of a single stage representing the whole cross-section. © 1998 John Wiley & Sons, Ltd.  相似文献   

6.
The permeability of river beds is an important control on hyporheic flow and the movement of fine sediment and solutes into and out of the bed. However, relatively little is known about the effect of bed permeability on overlying near‐bed flow dynamics, and thus on fluid advection at the sediment–water interface. This study provides the first quantification of this effect for water‐worked gravel beds. Laboratory experiments in a recirculating flume revealed that flows over permeable beds exhibit fundamental differences compared with flows over impermeable beds of the same topography. The turbulence over permeable beds is less intense, more organised and more efficient at momentum transfer because eddies are more coherent. Furthermore, turbulent kinetic energy is lower, meaning that less energy is extracted from the mean flow by this turbulence. Consequently, the double‐averaged velocity is higher and the bulk flow resistance is lower over permeable beds, and there is a difference in how momentum is conveyed from the overlying flow to the bed surface. The main implications of these results are three‐fold. First, local pressure gradients, and therefore rates of material transport, across the sediment–water interface are likely to differ between impermeable and permeable beds. Second, near‐bed and hyporheic flows are unlikely to be adequately predicted by numerical models that represent the bed as an impermeable boundary. Third, more sophisticated flow resistance models are required for coarse‐grained rivers that consider not only the bed surface but also the underlying permeable structure. Overall, our results suggest that the effects of bed permeability have critical implications for hyporheic exchange, fluvial sediment dynamics and benthic habitat availability. © 2017 The Authors. Earth Surface Processes and Landforms published by John Wiley & Sons Ltd.  相似文献   

7.
Bifurcations are key geomorphological nodes in anabranching and braided fluvial channels, controlling local bed morphology, the routing of sediment and water, and ultimately defining the stability of their associated diffluence–confluence unit. Recently, numerical modelling of bifurcations has focused on the relationship between flow conditions and the partitioning of sediment between the bifurcate channels. Herein, we report on field observations spanning September 2013 to July 2014 of the three‐dimensional flow structure, bed morphological change and partitioning of both flow discharge and suspended sediment through a large diffluence–confluence unit on the Mekong River, Cambodia, across a range of flow stages (from 13 500 to 27 000 m3 s?1). Analysis of discharge and sediment load throughout the diffluence–confluence unit reveals that during the highest flows (Q = 27 000 m3 s?1), the downstream island complex is a net sink of sediment (losing 2600 ± 2000 kg s?1 between the diffluence and confluence), whereas during the rising limb (Q = 19 500 m3 s?1) and falling limb flows (Q = 13 500 m3 s?1) the sediment balance is in quasi‐equilibrium. We show that the discharge asymmetry of the bifurcation varies with discharge and highlight that the influence of upstream curvature‐induced water surface slope and bed morphological change may be first‐order controls on bifurcation configuration. Comparison of our field data to existing bifurcation stability diagrams reveals that during lower (rising and falling limb) flow the bifurcation may be classified as unstable, yet transitions to a stable condition at high flows. However, over the long term (1959–2013) aerial imagery reveals the diffluence–confluence unit to be fairly stable. We propose, therefore, that the long‐term stability of the bifurcation, as well as the larger channel planform and morphology of the diffluence–confluence unit, may be controlled by the dominant sediment transport regime of the system. © 2017 The Authors. Earth Surface Processes and Landforms published by John Wiley & Sons Ltd.  相似文献   

8.
The origin and growth of blind tidal channels is generally considered to be an erosional process. This paper describes a contrasting depositional model for blind tidal channel origin and development in the Skagit River delta, Washington, USA. Chronological sequences of historical maps and photos spanning the last century show that as sediments accumulated at the river mouth, vegetation colonization created marsh islands that splintered the river into distributaries. The marsh islands coalesced when intervening distributary channels gradually narrowed and finally closed at the upstream end to form a blind tidal channel, or at mid‐length to form two blind tidal channels. Channel closure was probably often mediated through gradient reduction associated with marsh progradation and channel lengthening, coupled with large woody debris blockages. Blind tidal channel evolution from distributaries was common in the Skagit marshes from 1889 to the present, and it can account for the origin of very small modern blind tidal channels. The smallest observed distributary‐derived modern blind tidal channels have mean widths of 0·3 m, at the resolution limit of the modern orthophotographs. While channel initiation and persistence are similar processes in erosional systems, they are different processes in this depositional model. Once a channel is obstructed and isolated from distributary flow, only tidal flow remains and channel persistence becomes a function of tidal prism and tidal or wind/wave erosion. In rapidly prograding systems like the Skagit, blind tidal channel networks are probably inherited from the antecedent distributary network. Examination of large‐scale channel network geometry of such systems should therefore consider distributaries and blind tidal channels part of a common channel network and not entirely distinct elements of the system. Finally, managers of tidal habitat restoration projects generally assume an erosional model of tidal channel development. However, under circumstances conducive to progradation, depositional channel development may prevail instead. Copyright © 2006 John Wiley & Sons, Ltd.  相似文献   

9.
The effects of aquatic macrophytes on flow and turbulence were studied in a tightly curving meander bend. Three field measurement campaigns were carried out within a one year period to capture effects of seasonal changes in macrophyte cover. They comprised three‐dimensional velocity measurements and mappings of vegetation cover and bathymetry. Flow accelerates and converges over the run into an axial pool in a jet‐like flow pattern bordered by outer and inner bank flow separation zones. The jet and widening of the cross‐section anticipate helical flow until the second half of the bend, where an asymmetric pool developed. Submerged vegetation at the riffles preserves the jet at much lower discharges during the summer period by concentrating high momentum fluid near the surface. Plants locally modify the velocity and stress patterns, reduce bed shear stresses, create zones of fine sediment accumulation and reinforce the bed and banks with roots and rhizomes. Plant patches colonising the banks and the point bar confine secondary flow cells laterally and affect shape and magnitude of the transverse flow profiles near their edges. The morphology of the bend was very stable over the observation period and neither bank erosion nor pool scouring occurred. However, fine sediments accumulate within vegetation patches and in the recirculation zones while the remaining open areas tend to erode slightly. With the decay of macrophytes in winter, sediment accumulations are mobilised again and the bathymetry levels, supporting cyclic models of morphologic change in vegetated bends. In the second part of the paper, semi‐empirical models for the three predominant flow types were tested and discussed; velocity and stress models of vegetated mixing layers and plane turbulent jets, and Rozovskii's model for the transverse flow in bends. Copyright © 2012 John Wiley & Sons, Ltd.  相似文献   

10.
Bo Wang  Yi-Jun Xu 《水文研究》2020,34(13):2864-2877
Bed material transport at river bifurcations is crucial for channel stability and downstream geomorphic dynamics. However, measurements of bed material transport at bifurcations of large alluvial rivers are difficult to make, and standard estimates based on the assumption of proportional partitioning of flow and bedload transport at bifurcations may be erroneous. In this study, we employed a combined approach based on observed topographic change (erosion/deposition) and bed material transport predicted from a one-dimensional model to investigate bed material fluxes near the engineering-controlled Mississippi-Atchafalaya River diversion, which is of great importance to sediment distribution and delivery to Louisiana's coast. Yang's (1973) sediment transport equation was utilized to estimate daily bed material loads upstream, downstream, and through the diversion during 2004–2013. Bathymetric changes in these channels were assessed with single beam data collected in 2004 and 2013. Results show that over the study period, 24% of the Mississippi River flow was diverted into the Atchafalaya River, while the rest remained in the mainstem Mississippi. Upstream of the diversion, the bed material yield was predicted to be 201 million metric tons (MT), of which approximately 35 MT (i.e., 17%) passed through the bifurcation channel to the Atchafalaya River. The findings from this study reveal that in the mainstem Mississippi, the percentage of bed material diversion (83%) is larger than the percentage of flow diversion (76%); Conversely, the diversion channel receives a disproportionate amount of flow (24%) relative to bed material supply (17%). Consequently, severe bed scouring occurred in the controlled Outflow Channel to the Atchafalaya River, while riverbed aggradation progressed in the mainstem Mississippi downstream of the diversion structures, implying reduced flow capacity and potential risk of a high backwater during megafloods. The study demonstrates that Yang's sediment transport equation provides plausible results of bed material fluxes for a highly complicated large river diversion, and that integration of the sediment transport equation with observed morphological changes in riverbed is a valuable approach to investigate sediment dynamics at controlled river bifurcations.  相似文献   

11.
Channel meander dynamics in fluvial systems and many tidal systems result from erosion of concave banks coupled with sediment deposition on convex bars. However, geographic information system (GIS) analysis of historical aerial photographs of the Skagit Delta marshes provides examples of an alternative meander forming process in a rapidly prograding river delta: deposition‐dominated tidal channel meander formation through a developmental sequence beginning with sandbar formation at the confluence of a blind tidal channel and delta distributary, proceeding to sandbar colonization and stabilization by marsh vegetation to form a marsh island opposite the blind tidal channel outlet, followed by narrowing of the gap between the island and mainland marsh, closure of one half of the gap to join the marsh island to the mainland, and formation of an approximately right‐angle blind tidal channel meander bend in the remaining half of the gap. Topographic signatures analogous to fluvial meander scroll bars accompany these planform changes. Parallel sequences of marsh ridges and swales indicate locations of historical distributary shoreline levees adjacent to filled former island/mainland gaps. Additionally, the location of marsh islands within delta distributaries is not random; islands are disproportionately associated with blind tidal channel/distributary confluences. Furthermore, blind tidal channel outlet width is positively correlated with the size of the marsh island that forms at the outlet, and the time until island fusion with mainland marsh. These observations suggest confluence hydrodynamics favor sandbar/marsh island development. The transition from confluence sandbar to tidal channel meander can take as little as 10 years, but more typically occurs over several decades. This depositional blind tidal channel meander formation process is part of a larger scale systemic depositional process of delta progradation that includes distributary elongation, gradient reduction, flow‐switching, shoaling, and narrowing. Copyright © 2010 John Wiley & Sons, Ltd.  相似文献   

12.
Complex flow processes at river bifurcations and the influence of the layout of a bifurcation make it difficult to predict sediment distribution over the downstream branches in case bedload transport dominates. In one‐dimensional models we need a nodal point relationship that prescribes the distribution of sediment over the downstream branches. We have identified which factors need to be included in such a relationship for the division of bedload transport at bifurcations. Next, irrotational flow theory for idealized geometries has been used to derive a simple physics‐based nodal point relationship that accounts for the effects of helical flow in the situation that a channel takes off under an angle from a straight main channel. This first step towards a complete nodal point relationship is applicable to bedload transport situations if the flow is clearly curved and if there is no pronounced bed topography. The relationship has been tested against data from a unique set of laboratory measurements, numerical data and data from a scale model of the Rhine bifurcation at Pannerden in the Netherlands. We find that the derived model yields a reasonable prediction of the sediment division over the downstream branches, and yields better predictions than the Wang et al. model for the situation considered. Considering the relative complexity and limited accuracy of the nodal point relationship for the effect of helical flow alone, however, we conclude thatderiving a practical physics‐based 1‐D relationship including all relevant processes is not feasible. We therefore recommend 2‐D or 3‐D modelling for all cases in general where morphological evolution depends on the division of bedload transport at bifurcations. Copyright © 2012 John Wiley & Sons, Ltd.  相似文献   

13.
Northern rivers experience freeze‐up over the winter, creating asymmetric under‐ice flows. Field and laboratory measurements of under‐ice flows typically exhibit flow asymmetry and its characteristics depend on the presence of roughness elements on the ice cover underside. In this study, flume experiments of flows under a simulated ice cover are presented. Open water conditions and simulated rough ice‐covered flows are discussed. Mean flow and turbulent flow statistics were obtained from an Acoustic Doppler Velocimeter (ADV) above a gravel‐bed surface. A central region of faster flow develops in the middle portion of the flow with the addition of a rough cover. The turbulent flow characteristics are unambiguously different when simulated ice covered conditions are used. Two distinct boundary layers (near the bed and in the vicinity of the ice cover, near the water surface) are clearly identified, each being characterized by high turbulent intensity levels. Detailed profile measurements of Reynolds stresses and turbulent kinetic energy indicate that the turbulence structure is strongly influenced by the presence of an ice cover and its roughness characteristics. In general, for y/d > 0·4 (where y is height above bed and d is local flow depth), the addition of cover and its roughening tends to generate higher turbulent kinetic energy values in comparison to open water flows and Reynolds stresses become increasingly negative due to increased turbulence levels in the vicinity of the rough ice cover. The high negative Reynolds stresses not only indicate high turbulence levels created by the rough ice cover but also coherent flow structures where quadrants one and three dominate. Copyright © 2012 John Wiley & Sons, Ltd.  相似文献   

14.
This paper illustrates how the acoustic Doppler current profiler （ADCP） and single-beam echo-sounder （SBES） recordings can be used for the calibration of existing software to assist in generalizing the morphodynamic processes in large rivers at key sites such as bifi.trcations and confluences. Calibration of the MIKE21C numerical model by the Danish Hydraulic Institute at the 25-km-long reach of Lower Paran~ near Rosario （Argentina） is presented. This reach includes two downstream confluences and two bifurcations. The model simulates a 2-D depth-averaged flow velocity and the related sediment fluxes to predict the bifurcation morphodynamics that affects the Paranh waterway. To investigate the river channel bathymetry, roughness, flow discharge allocation at bifurcations, suspended sediment concentration and grain size distributions, several instruments were used. These instruments included two ADCPs by Teledyne RDI working at frequencies of 600 and 1,200 kHz, a Sontek ADCP working at a frequency of 1,000 kHz and a SBES. The method to assess suspended sediment concentration and grain size distributions has been previously described. This paper focuses primarily on investigating dune morphology （by means of SBES depth measurements） and friction velocity （by means of ADCP profiling） to determine the river channel bed-roughness. The 2-D model results agree with observed values of bed-roughness, flow velocity and suspended sediment concentration distributions at the investigated sections, known data of water slope and total load of bed sediment are in good agreement with model results.  相似文献   

15.
The Bulle effect is a phenomenon in which a disproportionately higher amount of near‐bed sediment load at a fluvial diversion moves into the diverted channel, even for cases in which the proportion of water (with respect to the main flow) entering the diversion channel is relatively small. This phenomenon has wide‐ranging implications for both engineered and natural systems: from efficient design of channels to redirect water and sediment for reclaiming sinking deltas, designing navigational channels that do not need frequent dredging, to morphological evolution of river bifurcations. The first ever, and one of the most extensive set of experiments conducted to explore this phenomenon, were conducted by Bulle in 1926 . In the current study the experiments conducted by Bulle have been simulated using an open‐source, free‐surface finite‐element‐based hydrodynamic solver. The main objectives were to explore to what extent the complex phenomenon of the Bulle effect at the scale of a laboratory experiment can be simulated accurately using Reynolds‐averaged Navier–Stokes (RANS)‐based hydrodynamic solver, and to understand the details of the hydrodynamics that Bulle could not analyze through his experiments. The hydrodynamics captured by the simulations were found to match the observations made by Bulle through his experiments, and the distributions of sediment at the diversion predicted by the numerical simulations were found to match the general trend observed in the laboratory experiments. The results from the numerical simulations were also compared with existing one‐dimensional models for sediment distribution at bifurcations, and the three‐dimensional numerical model was found to perform appreciably better. This is expected due to the complex flow features at the diversion, which can only be captured satisfactorily using a three‐dimensional hydrodynamic model. Copyright © 2017 John Wiley & Sons, Ltd.  相似文献   

16.
Supraglacial rivers on the Greenland Ice Sheet (GrIS) transport large volumes of surface meltwater toward the ocean, yet have received relatively little direct research. This study presents field observations of channel width, depth, velocity, and water surface slope for nine supraglacial channels on the south‐western GrIS collected between July 23 and August 20, 2012. Field sites are located up to 74 km inland and span 494–1485 m elevation, and contain measured discharges larger than any previous in situ study: from 0.006 to 23.12 m3/s in channels 0.20 to 20.62 m wide. All channels were deeply incised with near vertical banks, and hydraulic geometry results indicate that supraglacial channels primarily accommodate greater discharges by increasing velocity. Smaller streams had steeper water surface slopes (0.74–8.83%) than typical in terrestrial settings, yielding correspondingly high velocities (0.40–2.60 m/s) and Froude numbers (0.45–3.11) with supercritical flow observed in 54% of measurements. Derived Manning's n values were larger and more variable than anticipated from channels of uniform substrate, ranging from 0.009 to 0.154 with a mean value of 0.035 ± 0.027 despite the absence of sediment, debris, or other roughness elements. Ubiquitous micro‐depressions in shallow sections of the channel bed may explain some of these roughness values. However, we find that other, unobserved sources of flow resistance likely contributed to these elevated Manning's n values: future work should explicitly consider additional sources of flow resistance beyond bed roughness in supraglacial channels. We conclude that hydraulic modeling for these channels must allow for both subcritical and supercritical flow, and most importantly must refrain from assuming that all ice‐substrate channels exhibit similar hydraulic behavior, especially for Froude numbers and Manning's n. Finally, this study highlights that further theoretical and empirical work on supraglacial channel hydraulics is necessary before broad scale understanding of ice sheet hydrology can be achieved. Copyright © 2016 John Wiley & Sons, Ltd.  相似文献   

17.
Sediment flux in marsh tidal creeks is commonly used to gauge sediment supply to marshes. We conducted a field investigation of temporal variability in sediment flux in tidal creeks in the accreting tidal marsh at China Camp State Park adjacent to northern San Francisco Bay. Suspended‐sediment concentration (SSC), velocity and depth were measured near the mouths of two tidal creeks during three 6‐ to 10‐week deployments: two in winter and one in summer. Currents, wave properties and SSC were measured in the adjacent shallows. All deployments spanned the largest spring tides of the season. Results show that tidally averaged suspended‐sediment flux (SSF) in the tidal creeks varied from slightly landward to strongly bayward with increasing tidal energy. SSF was negative (bayward) for tidal cycles with maximum water surface elevation above the marsh plain. Export during the largest spring tides dominated the cumulative SSF for each deployment. During ebb tides following the highest tides, velocities exceeded 1 m s?1 in the narrow tidal creeks, resulting in negative tidally averaged water flux, and mobilizing sediment from the creek banks or bed. Storm surge also produced negative SSF. Tidally averaged SSF was positive in wavy conditions with moderate tides. Spring tide sediment export at the creek mouth was about twice that at a station 130 m further up the tidal creek. The negative tidally averaged water flux near the creek mouth during spring tides indicates that in the lower marsh some of the water flooding directly across the bay–marsh interface drains through the tidal creeks, and suggests that this interface may be a pathway for sediment supply to the lower marsh as well. Copyright © 2018 John Wiley & Sons, Ltd.  相似文献   

18.
River bifurcations are key nodes within braided river systems controlling the flow and sediment partitioning and therefore the dynamics of the river braiding process. Recent research has shown that certain geometrical configurations induce instabilities that lead to downstream mid‐channel bar formation and the formation of bifurcations. However, we currently have a poor understanding of the flow division process within bifurcations and the flow dynamics in the downstream bifurcates, both of which are needed to understand bifurcation stability. This paper presents results of a numerical sensitivity experiment undertaken using computational fluid dynamics (CFD) with the purpose of understanding the flow dynamics of a series of idealized bifurcations. A geometric sensitivity analysis is undertaken for a range of channel slopes (0.005 to 0.03), bifurcation angles (22° to 42°) and a restricted set of inflow conditions based upon simulating flow through meander bends with different curvature on the flow field dynamics through the bifurcation. The results demonstrate that the overall slope of the bifurcation affects the velocity of flow through the bifurcation and when slope asymmetry is introduced, the flow structures in the bifurcation are modified. In terms of bifurcation evolution the most important observation appears to be that once slope asymmetry is greater than 0.2 the flow within the steep bifurcate shows potential instability and the potential for alternate channel bar formation. Bifurcation angle also defines the flow structures within the bifurcation with an increase in bifurcation angle increasing the flow velocity down both bifurcates. However, redistributive effects of secondary circulation caused by upstream curvature can very easily counter the effects of local bifurcation characteristics. Copyright © 2011 John Wiley & Sons, Ltd.  相似文献   

19.
Flow fields and water and bed surface topography were measured at two different stages as flow shoals over a submerged mid-channel bar in a straight reach downstream of a bend in Solfatara Creek, Wyoming. The data allow calculation and comparison of the magnitude of the component terms in the downstream and cross-stream force balance at the different stages. At the lower stage, corresponding to a discharge that is 30 per cent of the bankfull discharge, the convective acceleration terms in the equations describing the force balance are important, particularly the terms associated with the cross-stream transport of momentum. These terms are large because of the large accelerations and cross-stream flow forced by the shallow flow over the bar. At the higher stage, corresponding to a discharge that is 45 per cent of the bankfull discharge, flow is more directly downstream and cross-stream velocity is generally less in most of the channel. Downstream flow velocities at the higher stage are larger, but the acceleration is more gradual. Consequently, the convective accelerations at the higher stage tend to be less important than at the lower stage. Results from the two different stages suggest that some of the difference in conclusions reached by various workers on the significance of the various terms in the governing equations may be associated with the relative depth of flow. © 1997 John Wiley & Sons, Ltd.  相似文献   

20.
An investigation has been conducted to identify the key parameters that are likely to scale laboratory sediment deposits to the field scale. Two types of bed formation were examined: one where sediment is manually placed and screeded and the second where sediment is fed into a running flume. This later technique created deposits through sequential cycles of sediment transport and deposition. Detailed bed surface topography measurements have been made over a screeded bed and three fed beds. In addition, bulk subsurface porosity and hydraulic conductivity have been measured. By comparing the four beds, results revealed that certain physical properties of the screeded bed were clearly different from those of the fed beds. The screeded bed had a random organization of grains on both the surface and within the subsurface. The fed beds exhibited greater surface and subsurface organization and complexity, and had a number of properties that closely resembled those found for water‐worked gravel beds. The surfaces were water‐worked and armoured and there was preferential particle orientation and direction of imbrication in the subsurface. This suggested that fed beds are able to simulate, in a simplified manner, both the surface and subsurface properties of established gravel‐bed river deposits. The near‐bed flow properties were also compared. It revealed that the use of a screeded bed will typically cause an underestimation in the degree of temporal variability in the flow. Furthermore, time‐averaged streamwise velocities were found to be randomly organized over the screeded bed but were organized into long streamwise flow structures over the fed beds. It clearly showed that caution should be taken when comparing velocity measurements over screeded beds with water‐worked beds, and that the formation of fed beds offers an improved way of investigating intragravel flow and sediment–water interface exchange processes in gravel‐bed rivers at a laboratory scale. Copyright © 2008 John Wiley & Sons, Ltd.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号