共查询到20条相似文献，搜索用时 681 毫秒
1.
采用颗粒流程序PFC构建了试件直接拉伸模型,模拟了含2条断续裂隙试件的直接拉伸试验,通过完整试件的模拟结果与室内试验结果的对比,验证了细观参数的准确性和可靠性,同时分析了裂隙倾角和岩桥倾角对抗拉强度和裂纹扩展的影响。研究表明:在直接拉伸情况下,含2条断续裂隙试件以萌生次生倾斜反翼裂纹为主,少量次生共面裂纹和翼裂纹;岩桥倾角和裂隙倾角均较小时,次生共面裂纹与原始裂隙之间发生搭接、贯通,随着岩桥倾角和裂隙倾角的加大,次生倾斜反翼裂纹扩展使试件断裂;裂纹扩展的方向与最大拉应力的方向基本保持垂直;岩桥倾角对于试件的抗拉强度和起裂应力影响不大;裂隙倾角对于试件抗拉强度和起裂应力影响明显,裂隙倾角越大,试件抗拉强度和起裂应力越大。 相似文献
2.
《岩土力学》2019,(11)
采用最新配置的水泥砂浆材料,通过在试件中布置倾斜裂隙和水平裂隙,开展了单轴和双轴条件下的压缩试验,详细分析了不同加载条件下试件裂隙的扩展和贯通规律。试验结果表明:无裂隙内水压时,在单轴压缩条件下倾斜裂隙在扩展贯通水平裂隙后裂纹的扩展路径和方向发生明显改变,试样最终发生劈裂破坏。侧压的增大抑制了倾斜裂隙端部翼裂纹和次生裂纹的萌生,高侧压下翼裂纹没有贯穿水平裂隙,试样破坏模式变成了剪切破坏。水力耦合作用下,单轴压缩时倾斜裂隙翼裂纹尖端的最大主应力分布范围随着内水压的增大逐渐变小,翼裂纹的起裂应力、起裂角和峰值强度逐渐降低,试样发生劈裂破坏。通过数值模拟得到的裂纹扩展贯通规律与试验结果具有良好的一致性,开展了不同内水压时倾斜裂隙扩展贯通无水压的水平裂隙的数值分析,随着内水压的增加倾斜裂隙首先萌生共面裂纹随后产生翼裂纹,翼裂纹扩展贯通水平裂隙时扩展路径同样会发生改变。水力耦合作用下侧压也会抑制翼裂纹的萌生,随着内水压的增大减弱了侧压对倾斜裂隙翼裂纹的抑制作用。 相似文献
3.
基于PIV技术,采用相似材料预制贯通单裂隙岩体试件并开展压-剪试验,探究了裂隙开度对贯通单裂隙试件的强度、变形及破坏过程的影响。结果表明:(1)试件发生初始断裂时不同裂隙开度试验组应力均明显下降,且随着开度的增大裂隙岩体胶结部位塑性变形增强,岩体试件的特征应力值减小;(2)裂隙开度影响到裂隙和胶结部位变形在试件总变形中所占比例,进而影响裂隙试件的轴向峰值应变和横向峰值应变,开度越大裂隙试件的轴向峰值应变与横向峰值应变越小;(3)随着开度增大试件初始断裂部位由中下部向中上部转移,同时试件逐渐由拉伸剪切复合破坏转变为单一的剪切破坏;(4)需达到位移阈值k试件表面才能产生裂隙,而预制裂隙开度增大会降低试件的位移阈值k。其结果为研究深部矿井裂隙沟通造成的突水溃砂机理奠定了一定的基础。 相似文献
4.
透明类岩石内置三维裂纹扩展变形试验研究 总被引：1，自引：0，他引：1
采用力学试验手段探究岩石受压情况下内部裂纹扩展贯通机制是了解岩石破坏失稳机制的重要手段。由于无法观察真实岩体内部裂纹扩展过程且CT扫描实时性不足等原因,自行研制了一种各项性质与岩石接近的透明类岩石材料,以观察研究其内部三维裂纹的扩展贯通机制。这一方法克服了真实岩体不透明的特点,可更方便地观察岩体内部裂纹萌生、扩展不同阶段的形状。然后制作了一批内置单裂隙和双裂隙的试件,在RMT-150B多功能全自动刚性岩石伺服试验机上进行单轴压缩试验,详细观察研究了单裂隙和双裂隙试件在不同岩桥角和裂隙间距情况下的裂纹扩展贯通模式以及裂隙数量和间距对试件抗压强度的影响,并从理论方面对翼形裂纹的扩展过程进行了解释。试验表明,在不同的岩桥角和裂隙间距下,次生裂纹将呈现不同的扩展贯通模式,试验中观察到的次生裂纹有张拉翼裂纹、与翼裂纹反向生长的反翼裂纹和拉剪作用下的花瓣状裂纹等,试件最终破坏是各种形式的裂纹汇合贯通的结果。裂隙的存在极大地降低了试件的抗压强度,且随着裂隙数目增加,试件峰值强度呈降低趋势,同时裂隙间距也对试件的峰值强度产生一定的影响。试验成果对分析真实岩体的破坏失稳机制有着重要的参考价值。 相似文献
5.
为研究水压致裂过程中水力裂缝的起裂、扩展规律及机制,研制了一种新型水压供给控制装置。该装置由水泵、增压泵、空气压缩机和导水钢垫板等组成。该装置的主要特点是易于与目前广泛存在的压力伺服机相配合,共同完成水压致裂试验,具有操作简便、效率高、成本低、组装方便等优点,使水压致裂试验更易大面积推广。利用该试验装置对类岩石试块进行了水压致裂试验,研究了不同围压下含预置裂隙试件的水力裂缝扩展规律,并与无预置裂隙试件水力裂缝扩展规律进行了对比。试验结果表明,对于含预置裂隙试块,当水平应力差较小时,预置裂隙裂尖对水力裂缝扩展影响较大,水力裂缝起裂后向预置裂隙裂尖方向扩展;随着水平应力差的增大,水力裂缝向最大水平应力方向偏转。试验证明该装置可靠性高,试验过程稳定。该研究对水压致裂试验具有促进意义。 相似文献
6.
岩体内部赋存的裂隙很多表现为折线型,为探究这类岩体的断裂机制,制备含折线型裂隙砂岩试件并对其进行单轴压缩试验。采用数字图像相关(DIC)方法计算加载过程中的变形场演化,根据新生裂纹两侧的位移差异识别裂纹类型;运用扩展有限元法(XFEM)模拟断裂过程,根据应力分布特征解释翼型裂纹起裂与扩展机制。DIC计算结果表明,新生裂纹处出现应变局部化带,裂纹两侧发生相对分离;含直线型和折线型裂隙砂岩试件的翼型裂纹分别萌生于预制裂隙端部以及折角处,这是因为裂隙几何形态会改变拉应力集中位置;含折线型裂隙砂岩试件的起裂应力小于含直线型裂隙砂岩试件,这是因为相同加载条件下前者的最大拉应力值更大;这2类试件的裂纹扩展均是由于裂纹尖端集中的拉应力引起的,裂纹依然呈张开状态;裂隙几何形态未改变试件的最终破坏模式,均表现为对角剪切破坏。 相似文献
7.
为了准确表征不同角度预制节理岩石在单轴压缩下的变形破坏模式,基于3D打印技术制作了节理模型用于模拟岩体中的结构面,通过水泥砂浆的浇筑得到含不同角度预制节理的岩石试件并进行单轴压缩试验,同时采用数字图像相关技术（DIC）观测、分析试验过程中试件裂纹产生、扩展以及贯通过程。结果表明：随着预制节理从0°增加到90°,试件强度与峰值应变均呈现先降低后升高的变化趋势,0°和45°试件弹性模量相对于完整试件有所降低。基于DIC检测结果,0°、30°、45°及60°试件裂纹皆从预制节理尖端部位起裂,各角度试件的起裂应力与试件强度变化规律一致。各角度试样起裂时在剪应力控制下以剪切翼型裂纹形式起裂,0°与45°试件裂纹在扩展过程由剪切发展为张拉型裂纹,30°和60°试件以剪切裂纹形式贯穿始终,90°试件从底部起裂并最终表现为张拉破坏。研究还发现,下翼起裂角θ2和上翼起裂角θ1之间存在明显的线性正相关关系,关系式为θ2 =0.828 6θ1 +12.185,且起裂应力大小变化与峰值应力变化一致,皆随节理角度的增加先减小后增大。 相似文献
8.
《岩土力学》2019,(11):4380-4390
水力耦合作用下裂隙岩体的破裂力学行为及声发射特征是关系到地下工程安全建设与灾变预测预警的关键问题。利用水泥砂浆材料及声发射技术开展了室内压缩破裂试验,研究了无水及水力耦合条件下含三维裂隙试件的破裂模式、力学特性、声发射特征以及水压和裂隙倾角的影响,分析了声发射信号主频特征随岩体破裂状态的变化规律。试验结果表明:随裂隙倾角增大,试件破裂模式经历了张拉为主-拉剪复合-剪切为主的转变过程;水压增大增强了试件张拉破裂模式,而剪切破裂模式在一定程度上被削弱;随水压升高,起裂应力、损伤应力和峰值强度均持续降低,水压对起裂应力及峰值强度的影响程度存在阈值(4 MPa);试件破裂过程中声发射撞击率变化呈现明显阶段性特征,从而为起裂和损伤应力判定提供了依据;试件不同破裂状态下的声发射信号呈现不同主频特征,相对高、中、低频波的主频值域区间具有非连续性,低频和高频信号占比与试件破裂状态存在对应关系,因此可为岩体破裂状态的预测预警提供参考信息。 相似文献
9.
为研究裂隙岩石破坏强度及裂纹扩展特征,采用MTS岩石力学试验机对单裂隙岩石进行单轴压缩试验,同步进行声发射、声波及摄像测试,研究裂隙岩石应力应变行为、声波及声发射特征与裂纹扩展、聚结的变化关系。结果表明,起裂应力、峰值强度及模量随裂隙倾角α变化一致,均先减小后增大,起裂应力和强度受α影响较大;裂纹间断性加速扩展引起的应力转移和释放(应力降),导致裂隙岩石应力-应变曲线呈阶梯状上升;应力降伴随着能量释放、刚度劣化和AE振铃计数的激增,随着α的增大,首次应力降和振铃计数陡增对应的应力逐渐增大,且振铃分布向峰值强度附近集中;裂纹起裂、扩展引起波幅和波速衰减,且波幅下降早于应力降的发生。α=0o岩样峰前波速降高达50%,随α的增大,波速下降点的应力逐渐增大,峰前波速降幅不断减小,α较小时峰前裂纹发育程度高,随着α的增大,峰前裂纹发育程度减弱,裂纹加速扩展、聚合向峰后转移;裂纹长度扩展到临界值时扩展速率会发生快速增大,随着α的增大,裂纹临界长度逐渐降低。 相似文献
10.
为研究干湿循环作用下裂隙炭质页岩能量演化及破坏特征,分别制作完整和裂隙倾角为30°、45°和60°的炭质页岩,利用MTS815岩石力学试验系统进行不同干湿循环作用下的三轴压缩试验,研究了干湿循环对单裂隙炭质页岩强度、破坏模式及能量演化的影响。结果表明:起裂应力、损伤应力和峰值应力处弹性能和耗散能与干湿循环呈指数函数关系;起裂应力处弹性能、耗散能和损伤应力处耗散能对干湿循环的敏感程度较低,损伤应力处弹性能和峰值应力处弹性能、耗散能对干湿循环的敏感程度较高。炭质页岩破坏模式受控于干湿循环和裂隙倾角,干湿循环为主控因素,裂隙倾角为次控因素;裂隙倾角为30°的干燥岩样为拉剪破坏,裂隙倾角为45°和60°的干燥岩样为剪切破坏;随着干湿循环次数的增加,宏观主裂纹长度增大,次要裂纹增加,破坏模式整体上向剪拉破坏发展。随着干湿循环次数的增加,起裂应力处储能水平Kci和损伤应力处储能水平Kcd逐渐增大,起裂和损伤应力处储能水平越高,岩石起裂和损伤更容易;Kcd可作为岩石破坏的预警指标,Kcd越大,岩石越易发生破坏。 相似文献
11.
An Experimental Study of Crack Coalescence Behaviour in Rock-Like Materials Containing Multiple Flaws Under Uniaxial Compression 总被引：4，自引：1，他引：3
Experiments on man-made flawed rock-like materials are applied extensively to study the mechanical behaviour of rock masses as well as crack initiation modes and crack coalescence types. A large number of experiments on specimens containing two or three pre-existing flaws were previously conducted. In the present work, experiments on rock-like materials (formed from a mixture of sand, plaster, limestone and water at mass ratio of 126:9:9:16) containing multiple flaws subjected to uniaxial compression were conducted to further research the effects of the layout of pre-existing flaws on mechanical properties, crack initiation modes and crack coalescence types. Compared with previous experiments in which only three types of cracks were found, the present experiments on specimens containing multiple flaws under uniaxial compression revealed five types of cracks, including wing cracks, quasi-coplanar secondary cracks, oblique secondary cracks, out-of-plane tensile cracks and out-of-plane shear cracks. Ten types of crack coalescence occurred through linkage among wing cracks, quasi-coplanar secondary cracks, oblique secondary cracks, out-of-plane shear cracks and out-of-plane tensile cracks. Moreover, the effects of the non-overlapping length and flaw angle on the complete stress–strain curves, the stress of crack initiation, the peak strength, the peak strain and the elastic modulus were also investigated in detail. 相似文献
12.
断续三裂隙砂岩强度破坏和裂纹扩展特征研究 总被引：4，自引：0，他引：4
利用岩石力学伺服试验机,对尺寸为80 mm×160 mm×30 mm的断续三裂隙砂岩试样进行了单轴压缩试验,研究了岩桥倾角? 2对断续三裂隙砂岩（? = 30°和? 1 = 60°）强度破坏和裂纹扩展特征的影响规律。与完整砂岩试样相比,断续三裂隙砂岩试样应力-应变曲线显示了较多的应力跌落,其峰值强度也呈显著降低趋势,但降低程度与? 2密切相关,随着? 2从75°增加到90°,峰值强度从82.04 MPa 降低到77.82 MPa,而当? 2从90°增加到120°,其峰值强度无明显变化。完整砂岩试样呈现轴向劈裂脆性破坏,而断续三裂隙砂岩试样是由许多从裂隙尖端产生的裂纹扩展与汇合,导致了其失稳破坏。通过照相量测技术,探讨了? 2对断续三裂隙砂岩试样裂纹扩展特征的影响：? 2为75°、90°和105°的断续三裂隙试样中裂隙①、③和②、③之间均出现了贯通,而裂隙①、②之间无任何贯通;? 2为120°的断续三裂隙试样中裂隙①、③和①、②之间均出现了贯通,而②、③之间无任何贯通。最后给出了断续三裂隙砂岩试样宏观变形特性与裂纹扩展过程之间的关系。 相似文献
13.
脆性岩石材料在压应力作用下常出现两类裂纹：翼型张拉裂纹和次生剪切裂纹。近场动力学是一种新型的无网格数值计算方法。在近场动力学理论中,采用积分形式的控制方程代替微分形式的控制方程使得该数值算法在断裂问题上具有独特的优势。将Mohr-Coulomb准则和最大主应力准则引入非普通“态”基近场动力学理论中,分别用于模拟材料常见的压剪和张拉破坏。这种扩展的非普通“态”基近场动力学可以有效地模拟脆性岩石材料在多种受力状态下的裂纹起裂、扩展和连接问题。通过5个不同的数值算例说明该数值算法在处理脆性岩石材料断裂问题的有效性和准确性。首先,通过模拟含圆孔的弹性板拉伸数值试验说明该数值算法的有效性和准确性。其次,数值模拟了简单三点弯曲试验以及不使用其他外部准则条件下动荷载作用下裂纹的分叉试验,所得结果与其他试验结果或数值结果相吻合,从而验证了该理论的有效性。然后,模拟了包含斜裂纹的巴西圆盘试验,裂纹扩展路径和计算所得的断裂韧度同样吻合于试验结果。最后,模拟了单轴压缩状态下,预制裂纹试样的裂纹扩展和连接问题。将该数值算法与试验结果对比表明,所提出的数值方法可以模拟和预测岩石类材料的张拉和压剪裂纹的起裂、扩展和连接行为。 相似文献
14.
Summary ?Cracks that initiate from pre-existing discontinuities can link with other cracks or with other discontinuities and produce
failure in a rock mass. The Displacement Discontinuity Method (DDM), FROCK, is used in this investigation to model experimental
observations on pre-cracked specimens of gypsum. In these experiments two fractures, which were either both open or closed,
were placed through the thickness of the specimens, and detailed observations of the cracking process were performed as the
specimens were loaded in uniaxial compression. The following aspects are studied for both open and closed fractures: 1) crack
initiation stress; 2) direction and propagation of the new cracks; 3) type of coalescence and stress at which it occurs. Modeling
is done considering the actual size of the specimens. Relations between the direction of initiation for each type of crack,
the orientation of the initial fractures, and the type and coalescence are established. In addition, comparisons between results
from experiments and predictions from the model are presented. The numerical results are in agreement with the experiments. 相似文献
15.
三叉裂隙是自然界普遍存在的一种岩体缺陷形式,其对岩体的力学特性有重要影响。对含预制三叉裂隙的水泥砂浆试样进行室内单轴压缩试验,配合使用摄像机拍摄裂纹的起裂、扩展、贯通过程,通过数字图像技术处理获取试样的应变场云图,并结合PFC2D程序研究不同?、? 条件下试样的强度特征、裂纹模式和裂纹演化扩展规律。研究表明：三叉裂隙对试样单轴抗压强度有明显的削弱作用。当? 恒定为120°时,试样在? = 30°时达到最大抗压强度;当? 恒定为90°时,随?增大,试样抗压强度呈先减小后增大的趋势,且当? = 45°时达到最大抗压强度。试样产生的裂纹可分为3类,分别是张拉型裂纹(Ⅰ型裂纹)、剪切型裂纹(Ⅱ型裂纹)、混合型裂纹(Ⅲ型裂纹)。这3类裂纹通常从裂隙尖端开始产生,并且Ⅰ型裂纹沿加载方向扩展,通常未扩展至试样边界;Ⅱ型和Ⅲ型裂纹通常与加载方向呈一定角度扩展至试样边界。通过对裂纹的几何形态和组成宏观裂纹的微裂纹成分的分析,得知导致含三叉裂隙试样在单轴压缩条件下失效的是张拉破坏。数字图像技术得到的应变云图表明,当载荷达到一定阶段,裂隙尖端出现应力集中,微破裂开始发育并聚集成微破裂区,微破裂区扩大产生宏观裂纹。通过对主应变和剪应变云图分析,发现导致试样失效的是张拉破坏,剪应变在裂纹扩展过程中的影响较小。 相似文献
16.
Crack coalescence in rock masses was studied by performing a series of biaxial compresion tests on specimens made of rock-like
material. Specimens of size 63.5 × 27.9 × 20.3 cm, made of 72% silica sand, 16% cement (Type I) and 12% water by weight were
tested. The joint inclination angle was maintained at 45°, while the offset angle i.e. angle between the plane of the joint
and the line that connects the two inner tips of the joints, was changed from 0° to 90° with an increment of 15°. Three levels
of lateral stress were used; 0.35 MPa, 0.7 MPa and 1.5 MPa on each sample. HP data acquisition system was used to record the
data for each sample. In each sample, four LVDTs were fixed to measure the axial and lateral displacement along the sample.
The failure mechanisms were monitored by eye inspection and a magnifier to detect crack initiation and propagation. For each
test, the failure surfaces were investigated to determine the characteristics of each surface. Wing cracks initiated at the
tip of the joint for the low confining stress applied, while at higher confining stresses wing cracks also initiated at the
middle of the joint. Secondary cracks initiated at the tip of the joint due to shear stress. Three modes of failure took place
due to coalescence of the secondary and wing cracks. The bridge inclination was the main variable that controlled the mode
of failure. For bridge inclination of 0°, the coalescence occured due to shear failure and for bridge inclination of 90° the
coalescence occurred due to tensile failure while for the other bridge inclinations coalescence occured due to mixed tensile
and shear failure. 相似文献
17.
Cracking and coalescence behavior in a rectangular rock-like specimen containing two parallel (stepped and coplanar) pre-existing open flaws under uniaxial compression load has been numerically studied by a parallel bonded-particle model, which is a type of bonded-particle model. Crack initiation and propagation from two flaws replicate most of the phenomena observed in prior physical experiments, such as the type (tensile/shear) and the initiation stress of the first crack, as well as the coalescence pattern. Eight crack coalescence categories representing different crack types and trajectories are identified. New coalescence categories namely “New 1” and “New 2”, which are first observed in the present simulation, are incorporated into categories 3 and 4, and category 5 previously proposed by the MIT Rock Mechanics Research Group, respectively. The flaw inclination angle (β), the ligament length (L) (spacing between two flaws) and the bridging angle (α) (inclination of a line linking up the inner flaw tips, between two flaws) have different effects on the coalescence patterns, coalescence stresses (before, at or post the peak stress) as well as peak strength of specimens. Some insights on the coalescence processes, such as the initiation of cracks in the intact part of specimens at a distance away from the flaw tips, and coalescence due to the development and linkage of a number of steeply inclined to vertical macro-tensile cracks are revealed by the present numerical study. 相似文献
18.
Cracks and joints are common in rock masses and play a crucial role in rock mass stability. This study prepared specimens with multiple parallel pre-existing flaws by embedding iron sheets in rock-like materials and used the samples to investigate the crack growth characteristics of these materials. Biaxial compression experiments were performed on sixty specimens, and the influences of the number of pre-existing flaws, their angles and the lateral stress on crack growth were investigated based on video recordings of the crack growth. The results demonstrate that structural failure will occur due to crack growth when the sample contains a small number of pre-existing flaws and that as the number of cracks increases, the specimens will fail due to local failures. In addition, the types of rock bridge failures are summarized, including wing cracks, secondary shear cracks between horizontally-separated pre-existing flaws and secondary shear cracks between vertically-separated pre-existing flaws. Wing cracks play a significant role in the failure of the specimens. The results increase the understanding of crack growth in brittle materials that contain multiple parallel pre-existing flaws under biaxial compression. 相似文献
19.
Fracture Initiation and Propagation in a Brazilian Disc with a Plane Interface: a Numerical Study 总被引：1，自引：1，他引：0
M. Cai 《Rock Mechanics and Rock Engineering》2013,46(2):289-302
In the present study, fracture initiation and propagation from a pre-existing plane interface in a Brazilian disc is investigated using a finite-discrete element combined method. Different fracture patterns, depending on the frictional resistance of the pre-existing crack or interface, are observed from the numerical simulation. It is found that when there is no or very little frictional resistance on the surfaces of the pre-existing crack, the primary fractures (wing cracks), which are tensile in nature and are at roughly right angles to the pre-existing crack, start from the tips of the pre-existing crack. As the friction coefficient increases, the wing cracks’ initiation locations deviate from the crack tips and move toward the disc center. Secondary fractures, which are also tensile in nature, initiate from the disc boundary and occur only when the length of the pre-existing crack is sufficiently long. The secondary fractures are roughly sub-parallel to the pre-existing crack. The failure load is found to be influenced by the friction coefficient of the pre-existing crack. A 38 % failure load increase can result when the friction coefficient changes from 0 to 1. A good understanding of the fracture initiation and propagation in the forms of primary and secondary fractures provides insight into explaining some fracture patterns observed underground. 相似文献
20.
膨胀土易发育大量裂隙,对其工程性质影响显著。引入一种膨胀土试样预制裂隙方法,对特定裂隙形态下膨胀土试样开展无侧限抗压试验,研究了膨胀土强度特征受裂隙形态的影响,并揭示了裂隙的作用机制。研究结果表明：（1）裂隙形态显著影响试样破坏模式,垂直于受力方向裂隙越宽,破坏模式由剪切-拉伸破坏向张拉破坏转变;平行于受力方向裂隙条数... 相似文献