共查询到20条相似文献，搜索用时 104 毫秒
1.
针对构件外表面局部区域遭受随机点蚀损伤的圆管截面,考虑点蚀随机特性的影响,建立包含点蚀坑细节的精细有限元模型;在多种腐蚀强度下,研究局部腐蚀的点蚀区分布位置(沿轴向和周向分布位置变化)及其形状(点蚀区长度和宽度独立或联合变化)影响轴压极限强度退化的规律;并比较局部随机点蚀与局部均匀腐蚀引起构件极限强度退化的差异。研究结果表明,尽管局部随机点蚀与最大初始几何缺陷的耦合作用会使极限强度的退化趋于严重,但是总体而言点蚀区分布位置变化对圆管极限强度的退化没有显著的影响。此外,同等腐蚀体积和腐蚀面积下,相比于长窄式局部腐蚀,短宽式局部腐蚀会引起更严重的极限强度退化,在严重腐蚀情形下后者导致的强度退化会高出25.5%;相比于局部均匀腐蚀,局部随机点蚀会导致更剧烈的极限强度退化,其不利影响可高出20.7%。 相似文献
2.
船舶与海洋结构在服役期间会遭受电化学和微生物侵蚀等多种腐蚀环境影响,加筋板作为此类结构的主要受力构件,其表面易产生不规则形态的点蚀,引起构件的强度退化。利用ANSYS有限元软件构建加筋腹板遭受随机点蚀损伤的加筋板有限元模型,研究带板长宽比、带板长细比、加筋长细比和腐蚀体积损失率对加筋板极限强度的影响。研究结果表明,加筋遭受同等腐蚀体积损失率下,带板长宽比变化对极限强度退化的影响很小,但带板长细比和加筋长细比变化产生的影响明显;带板长细比越大,极限强度退化越严重,而加筋长细比越大,极限强度退化反而越小。针对文中研究的加筋板,当加筋长细比为 0.2时,腐蚀体积率为14%的随机点蚀导致结构极限强度退化程度达到约14.0%。因此,加筋的随机点蚀损伤会显著削弱加筋板结构的极限强度,其影响不可忽略。 相似文献
3.
It is well known that pitting corrosion occurring on surface of hull structural plate will surely result in a significant degradation of the ultimate strength of the hull structural plate. This report aims at development of an assessing formula for ultimate strength of hull plate with pitting corrosion damage under the biaxial in-plane compression loading. The ultimate strength assessment model that is in terms of the corroded volume loss was deduced in theory, and which was then completed through numerical experiment by employing nonlinear finite element analyses for series of corroded plate models. Meanwhile, pitting corrosion in actual ship hull was analyzed and simulated, which ensured that all the assumptions for the finite element model parameters were in accord with the actual hull plate with pitting corrosion damage. Furthermore, the effects of plate slenderness, the linear factors at the plate edges and the ratio between the transverse and the longitudinal in-plane stresses on the ultimate strength reduction related to the corroded volume loss were discussed. The ultimate strength assessment formula being in terms of corroded volume loss developed in this research is expected to be applicable to assess the ultimate strength of the hull structural plate with pitting corrosion damage. 相似文献
4.
In this work, we focus on assessing the group effect of localized corrosion on the ultimate strength of the marine structural plates and study the load-deformation behaviors of plates of various slenderness and uniaxial compression. Meanwhile, we investigate different corroded patterns from a single circular pit to 25 circular pits distributed over the plate and carry out hundreds of nonlinear finite element simulations by combining the number, depth, distribution of pits with imperfections and slenderness of plate. The distribution of multiple pits causes scattering of stress concentration on the plate, then the plastic section of plate changes with wider distribution of damage simultaneously. The ultimate strength arises when un-loading zone comprised of the yielding strips and holes extends across the plate. It can be concluded that the corroded condition defined as group effect of pits manipulates the deformation state and the loading capacity of plate at the ultimate strength mode that coincides with the proportion of effective loading area and section in the process of post-buckling. To validate the effect of pits group, we perform the numerical experiments of the post-buckling of steel plates containing pits in a row with different orientation. 相似文献
5.
提出一种随机分布点蚀损伤的模拟方法,模拟点蚀在构件表面的随机生长过程,并建立了随机态点蚀损伤圆管截面的有限元分析模型;设计了三个受不同腐蚀深度点蚀损伤的圆管构件,并开展轴压试验,利用试验结果校验有限元模型的计算精度;在多种腐蚀情形下(点蚀强度和腐蚀深度变化),研究点蚀分布模式变化引起的极限强度退化及其变异性;比较随机分布点蚀模型与传统腐蚀模型(规则分布点蚀和均匀腐蚀)在计算强度和结构失效行为方面的差异。研究结果表明,点蚀的随机分布模式会引起显著的极限强度变异,且蚀坑深度越大,强度变异越大,蚀坑分布造成的强度极差与强度均值相比达到5%;随机分布点蚀相比于传统腐蚀模型,除了引起更为严重的强度削减,还会改变结构的破坏模式。提出的随机点蚀损伤的模拟方法,可替代昂贵的构件试验,应用于评估点蚀损伤圆管截面的极限强度,增强评估结果的可靠性。 相似文献
6.
7.
点蚀损伤下桩基式平台腿柱轴压极限承载力研究 总被引：2，自引：0，他引：2
采用圆柱体点蚀损伤模型,建立含细观尺度点蚀损伤的桩基式平台腿柱多尺度精细化数值模型,研究壁厚损伤度、点蚀损伤强度以及点蚀体积损伤强度影响平台腿柱轴压极限承载力的规律。研究结果表明,壁厚损伤度及点蚀损伤强度明显削弱平台腿柱的极限强度,且随点蚀损伤强度增大壁厚损伤度的影响加剧;点蚀体积损伤强度由于综合考虑了壁厚损伤度和点蚀损伤强度的耦合因素,相比于独立考虑后两者,其更能合理地描述点蚀损伤对平台腿柱极限强度的影响,故点蚀体积损伤强度体现了点蚀损伤的关键特征。本方法不仅适用于研究点蚀损伤构件的极限承载力,其所提出的点蚀损伤模型的构建方法,可拓展于研究受点蚀损伤的整体平台结构的极限承载力,且确定点蚀体积损伤强度为描述点蚀损伤特征的关键参数后,有望将其用于修正点蚀损伤平台腿柱的承载力设计公式。 相似文献
8.
钢筋锈蚀是严重威胁结构安全的耐久性问题,基于压磁效应,研究均匀锈蚀和坑蚀两种锈蚀钢筋的应力状态与压磁场变化的关系。首先,采用通电加速锈蚀方法进行钢筋均匀锈蚀和点蚀试验;然后,通过轴向拉伸静载试验和疲劳加载试验,分析锈蚀钢筋的压磁信号特征。试验结果显示,磁感强度与钢筋应力状态之间具有较好的对应关系,屈服阶段不同锈蚀率下的钢筋磁感强度曲线有较明显区别,疲劳荷载作用下锈蚀钢筋的法向残余磁感强度和磁滞回环面积均呈现疲劳三阶段变化规律,可进一步运用于钢筋应力状态的检测中。 相似文献
9.
基于EIFS和P-M的海底管道腐蚀疲劳寿命预测 总被引：1，自引：1，他引：0
鉴于腐蚀疲劳损伤的特殊性,研究了点蚀过程和腐蚀疲劳裂纹扩展过程。基于等效初始缺陷尺寸(EIFS)和线性累积损伤理论(P-M)方法,消除了点蚀形核、蚀坑生长及腐蚀疲劳短裂纹扩展对腐蚀疲劳寿命预测的影响;避免了基于单点蚀坑建立的腐蚀疲劳寿命预测表达式的弊端;合理地简化了随机荷载下腐蚀疲劳寿命的预测流程。利用现有试验数据,对基于EIFS和P-M方法建立的腐蚀疲劳寿命预测表达式进行了模型验证。结果显示,所提模型的有效性和合理性得到了验证,为工程实际中海底管道的腐蚀疲劳寿命预测提供了一种可行方法。 相似文献
10.
Corrosion of offshore platforms is inevitable. In an ocean corrosion environment, the strength of a platform is weakened greatly. When simultaneously subjected to earthquakes or other extreme loads, the ultimate bearing capacity of the corroded platform is dramatically reduced, resulting in compounded damage from both corrosion and earthquake. Thus, the influence of corrosion cannot be neglected in the seismic performance investigation of platforms. The commonly used corrosion model in platform design is uniform corrosion, and the corrosion rate rule for any parts or zones in a platform is the same. In real cases, however, there are significant differences between the corrosion characteristics in different parts of a platform. Based on theoretical aspects and measured data, a zonal time-variant corrosion model of a platform is developed for a seismic collapse performance investigation. The pushover and incremental dynamic analysis (IDA) methods are adopted here to calculate the collapse margin ratio (CMR), there serve strength ratio (RSR) and ductility coefficient (μ) that are frequently used for the safety reserve evaluation of a platform. The failure reason and collapse probability of platforms considering different service periods are compared. The most prominent feature of the proposed time-variant zonal corrosion model is to capture potential switch of weak location and resulting failure path of corroded jacket offshore platforms although the proposed model needs further calibration by more reliable in-field measured data. As expected, corrosion can definitely cause a reduction in earthquake resistance of a jacket offshore platform, as well as ultimate deformability. The coupled effect between the time-variant vibration properties of the platform and the spectral characteristics of selected motions, the collapse-level spectral acceleration (SA) does not always decrease with increasing corrosion degree. The curves corresponding to normalized CMR and RSR agree very well with each other in the early corrosion development stage and service period beyond 30 years. Some distinct differences can be found during the two stages, with the greatest difference up to 10% for the example platform. 相似文献
11.
In jacket-type offshore structures, corrosion damage affects the structural performance under compressive loading, which is created by the working and design loads of the main system. In this study, the effects of corrosion damage on the compressive structural behavior and strength of steel tubular members were investigated. Artificial corrosion damage was applied to the tubular specimens via mechanical processing and hand drilling to replicate the inclined nature of jacket-type offshore structures. The damage was applied to either half or all of the circumference of the specimens. The compressive failure modes of the artificially corroded tubular members were affected by the corrosion conditions. The compressive strengths were also affected by the level of corrosion. From the results of this study, the residual compressive strengths of corroded tubular steel members can be estimated based on the condition of the damaged sectional areas. 相似文献
12.
Based on the elastic-plastic, large-deformation finite element method, burst capacity of steel pipeline with longitudinal corrosion defect subjected to internal pressure is studied. The appropriate stress-based criterion is used to predict the failure pressure of finite element model of corroded pipeline under internal pressure. By considering the pipe steel grades and geometries of corrosion defects, a series of finite element analyses is conducted. The effects of corrosion depth, length and width on burst capacity are also discussed. A specific failure pressure solution for the assessment of corrosion defects in moderate-to-high strength pipeline is proposed on the base of numerical results. The failure pressures predicted by the proposed method are in better agreement with the experimental results than the results by the other methods. 相似文献
13.
主要探讨了半潜钻井平台浮体结构由于受到海洋环境腐蚀作用后的时变极限强度问题。首先,总结各种关于腐蚀损伤的平均厚度缩减模型,选择较能反映实际腐蚀过程的数学模型来估量浮体的钢板厚度缩减。在此基础上进行一系列极限强度计算,根据计算结果给出浮体极限强度预报公式。最后研究不同纵向构件板厚折减对极限强度的影响,发现浮体角隅板的单位体积影响率最高,而占结构比例大的构件厚度折减也将使得强度大大削弱,这两类纵向构件需要予以重点腐蚀保护。 相似文献
14.
Study on Interaction Relationship for Submarine Pipeline with Axial Corrosion Defects 总被引：2，自引：0，他引：2
Corrosion is one of the main reasons to cause the operation accident of submarine oil and gas transmission pipelines. As the major corrosion pattern in submarine pipelines, the effects of corrosion clusters consisting of the adjacent corrosion defects on failure pressure are investigated through non-linear large-deformation finite element method. Typically, the failure behavior and limit strength of submarine pipeline with axial groove-groove corrosion defect pair exposed to internal pressure are analyzed. The effects of corrosion depth and axial spacing between a pair of corrosion defects on failure pressure are concluded. An interaction relationship for corrosion defects in pipelines, as well as prediction formulations for assessing the remaining strength of corroded pipelines are proposed. The expressions based on the proposed interaction relationship give more accurate results than the methods used in the existing design guidelines. 相似文献
15.
16.
含有腐蚀缺陷海底管道极限载荷分析 总被引：8，自引：0，他引：8
利用有限元弹塑性分析方法,对含有腐蚀缺陷的海底管道进行材料非线性和几何非线性分析,探讨了确定管道极限载荷的准则。在此基础上,给出含有腐蚀缺陷的海底管道的极限载荷,研究腐蚀长度、深度和宽度对海底管道极限载荷的影响,提出了含有腐蚀缺陷的受内压的海底管道的极限载荷计算公式,并与试验结果进行了比较,证明该方法是有效的。 相似文献
17.
《中国海洋工程》2020,(4)
An investigation is conducted on the static ultimate limit state assessment of ship hull plates with elastically restrained edges subjected to axial compression. Both material and geometric non-linearities were considered in finite element(FE) analysis. The initial geometric imperfection of the plate was considered, while the residual stress introduced by welding was not considered. The ultimate strength of simply supported ship hull plates compared well with the existing empirical formula to validate the correctness of the applied boundary conditions, initial imperfection and mesh size. The extensive FE calculations on the ultimate strength of ship hull plates with elastically restrained edges are presented. Then a new simple empirical formula for plate ultimate strength is developed, which includes the effect of the rotational restraint stiffness, rotational restraint stiffness, and aspect ratios. By applying the new formula and FE method to ship hull plates in real ships, a good coincidence of the results between these two methods is obtained, which indicates that the new formula can accurately predict the ultimate strength of ship hull plates with elastically restrained edges. 相似文献
18.
1 .Introduction Submarine pipelines are one of the safest and the least environmentally disruptive means for ma-rine gas or oil transport . With the development of exploitation of submarine oil or gas ,the safety ofsubmarine pipelines has becomethe major … 相似文献
19.
Corrosion and fatigue cracks are major threats to the structural integrity of aging offshore platforms. For the rational estimation of the safety levels of aging platforms, a global reliability assessment approach for aging offshore platforms with corrosion and fatigue cracks is presented in this paper. The base shear capacity is taken as the global ultimate strength of the offshore platforms. It is modeled as a random process that decreases with time in the presence of corrosion and fatigue crack propagati... 相似文献
20.
The new simple design equations for predicting the ultimate compressive strength of stiffened plates with initial imperfections in the form of welding-induced residual stresses and geometric deflections were developed in this study. A non-linear finite element method was used to investigate on 60 ANSYS elastic–plastic buckling analyses of a wide range of typical ship panel geometries. Reduction factors of the ultimate strength are produced from the results of 60 ANSYS inelastic finite element analyses. The proposed design equations have been developed based on these reduction factors. For the real ship structural stiffened plates, the most general loading case is a combination of longitudinal stress, transverse stress, shear stress and lateral pressure. The new simplified analytical method was generalized to deal with such combined load cases. The accuracy of the proposed equations was validated by the experimental results. Comparisons show that the adopted method has sufficient accuracy for practical applications in ship design. 相似文献