共查询到20条相似文献，搜索用时 329 毫秒
1.
探讨了对处于受压状态的堆石料进行干湿、冷热变化等环境因素作用下力学性质研究的试验方法。使用新研制的堆石料风化试验仪,对某种泥质粉砂岩堆石料进行了干湿循环、冷热循环以及湿冷-干热耦合变化三种环境条件下的长期变形特性试验研究,探讨了堆石料长期劣化变形的机制。试验结果表明,干湿循环试验和湿冷-干热耦合循环均可导致堆石体产生较大幅度的附加变形,其变形机制包括湿化变形、堆石体颗粒湿胀和干缩循环变形以及堆石料的劣化变形等。环境因素的循环变化可导致堆石体颗粒的劣化,堆石体劣化变形是高土石坝后期变形的重要组成部分。 相似文献
2.
湿化变形是土石坝的主要后期变形之一,对坝体的应力变形性状具有显著影响。采用糯扎渡高心墙堆石坝的弱风化花岗岩堆石料进行了常规三轴试验、不同围压和应力水平条件下的流变-湿化组合试验和快速湿化三轴试验等,分析了流变-湿化组合试验各阶段的变形特征,重点研究了堆石料湿化变形的过程、特性及发生机制。结果表明,可将堆石料湿化变形划分为湿化瞬时变形和湿态流变变形两个部分。其中,湿化瞬时变形是堆石料随浸水饱和过程发生的变形,其应变增量的方向平行于相应应力状态下应力加载应变增量的方向,且具有非硬化特性;湿态流变变形是堆石料试样在饱和浸水完成后发生的随时间的变形,和一般堆石料的流变变形具有相类似的特性。湿化变形是堆石料浸水后所导致的物态弱化变形。可将堆石料湿化看作一种广义的荷载。 相似文献
3.
4.
堆石料流变的主要机理是由于水位变化、降雨入渗、日晒雨淋等环境因素导致堆石料发生性质劣化,与此同时,颗粒发生高接触应力-破碎和重新排列-应力释放、调整和转移,这一过程由于颗粒的持续劣化而不断重复。在考虑颗粒破碎的堆石体不连续变形分析方法(SGDD)中,引入颗粒强度劣化模型反映颗粒强度随外界环境的持续劣化。应用该方法进行堆石料三轴流变数值试验,模拟结果与室内试验所观察到的规律一致,表明考虑流变效应的SGDD方法抓住堆石料流变的主要机理,适合模拟堆石料的流变变形这一复杂的、非线性演化问题。数值试验结果表明,堆石料随外界环境的劣化程度、劣化速率、母岩强度对宏观流变变形有较大影响。 相似文献
5.
Meng-Chia Weng 《Rock Mechanics and Rock Engineering》2014,47(4):1197-1209
Based on the concept of generalized plasticity, this study proposes a constitutive model to describe the time-dependent behavior and wetting deterioration of sandstone. The proposed model (1) exhibits nonlinear elasticity under hydrostatic and shear loading, (2) follows the associated flow rule for viscoplastic deformation, (3) adopts a creep modulus that varies with the stress ratio, (4) considers the primary and secondary creep behaviors of rock, and (5) considers the effect of wetting deterioration. This model requires 13 material parameters, comprising 3 for elasticity, 7 for plasticity, and 3 for creep. All parameters can be determined easily by following the suggested procedures. The proposed model is first validated by comparison with triaxial tests of sandstone under different hydrostatic stress and cyclic loading conditions. In addition, the model is versatile in simulating time-dependent behavior through a series of multistage creep tests. Finally, to consider the effects of wetting deterioration, triaxial and creep tests under dry and water-saturated conditions are simulated. Comparison of the simulated and experimental data shows that the proposed model can predict the behavior of sandstone in dry and saturated conditions. 相似文献
6.
The post-construction settlement of rockfill dams and high filled ground of airport, which is a phenomenon of much significance, is mainly caused by the time-dependent breakage of the rockfill material. In this paper, a random virtual crack DEM model is proposed for creep behavior of rockfill in PFC2D according to the theory of subcritical crack propagation induced by stress corrosion mechanisms. The bonded clusters are adopted to represent the rockfill particles so as to simulate their irregular shapes. Virtual cracks are set at the bonds of the clusters, and the length of the crack is considered as a random value, which leads the crushing strength of a single particle to follow the Weibull’s statistical model and the corresponding size rules. Oedometric creep tests for rockfill are simulated by using this proposed model. The results show that the model, validated preliminarily by some test data, can reflect qualitatively the creep mechanism as well as the size effects reasonably. Particles can develop various breakage patterns during creep, including global breakage, local breakage and even complex mixed breakage. The increase in stress levels and particle size will lead to an obvious growth of the creep strain and creep rate of the rockfill. The scale effects on the creep behavior of rockfill are analyzed through 35 specimens, and formulas including the effects of scales and stress levels are tentatively proposed. 相似文献
7.
The wetting deformation of coarse granular materials is often considered to be an important cause of the core wall rockfill dam cracks during impounding. By analyzing existing research results, this paper proposes a hyperbolic relationship between the wetting axial strain and wetting stress level and puts forwards a warped surface relationship among spherical stress, shear stress, and the ratio of wetting volumetric strain to wetting axial strain. To illustrate its practicability, the wetting strain model's parameter determination process is introduced and the rockfill materials wetting parameters are determined using the triaxial wetting test data. Moreover, the collapse settlement of Guanyinyan rockfill dam during first impounding is numerically simulated using the proposed method to calculate rockfill wetting deformation and verified by field measurements and monitoring data. The results show that the calculative method of wetting deformation proposed in this paper is reasonable and practical; the wetting deformation of upstream rockfill materials would cause an adverse deformation trend, which may lead to crack occurrence at the upstream slope and dam crest; and the Guanyinyan rockfill dam cracks on the top of junction mainly caused by the wetting deformation of upstream rockfill. 相似文献
8.
土石料的湿化是一种普遍现象,虽然可以利用非饱和理论计算湿化变形,但人们更愿意采用常规的初应变法进行计算,湿化试验则常用单线法或双线法进行。对湿化试验和相关计算方法进行分析,提出考虑湿化变形及其影响的新思路,（1）在某一应力状态下的湿化变形是由两部分组成的,一部分是由于材料本身刚度变“软”引起的湿化变形,另一部分变形是湿化引起的附加变形;（2）在双线法试验中直接将相同应力状态下对应干土和湿土的应变相减计算是不合适的,应当采用相同应力状态下各自的切线模量计算;（3）基于广义位势理论,根据应力和应变的对偶特性,可以把湿化附加变形变换为一种湿化等效应力,虽然其是一种近似处理方法,但它比较简单,容易直观地量化湿化的作用。文中思路对于颗粒破碎、干湿循环引起的变形、流变变形等也具有借鉴意义。 相似文献
9.
The formation of Ca-rich myrmekites is described in syntectonic syenites crystallized and progressively deformed under granulite facies conditions. The syenites are found in high- and low-strain zones where microstructure and mineral composition are compared. Heterogeneously distributed water-rich, late-magmatic liquids were responsible for strain partitioning into dry and wet high-strain zones at outcrop scale, where contrasting deformation mechanisms are reported. In dry high-strain zones K-feldspar and clinopyroxene are recrystallized under high-T conditions. In wet high-strain zones, the de-stabilization of clinopyroxene and pervasive replacement of relatively undeformed K-feldspar porphyroclasts by myrmekite and subordinate micrographic intergrowths indicate dissolution-replacement creep as the main deformation mechanism. The reworking of these intergrowths is observed and is considered to contribute significantly to the development of the mylonitic foliation and banding. A model is proposed for strain partitioning relating a positive feedback between myrmekite-forming reaction, continuous inflow of late-magmatic liquids and dissolution-replacement creep in the wet zone at the expenses of original mineralogy preserved in the dry zones. Melt-assisted dissolution-replacement creep in syntectonic environments under granulite-facies conditions may extend the field of operation of dissolution-replacement creep, changing significantly the rheology of the lower continental crust. 相似文献
10.
考虑拱效应的高面板堆石坝流变收敛机制研究 总被引：1，自引：0，他引：1
采用一种能模拟高围压条件的堆石料幂函数流变本构模型,探讨狭窄河谷条件下堆石体流变变形的发展规律及相应的控制流变变形的工程措施。数值仿真结果表明,在狭窄河谷中的堆石体存在着拱效应。由于拱效应的影响,如果不考虑堆石体流变导致拱效应减弱而增加的附加变形,数值仿真计算得到的大坝变形将小于其真实的变形。受拱效应影响,堆石体初期变形的速率受到抑制,但随着坝体的升高、蓄水后水压力的加大以及堆石体随时间发展等流变变形因素的影响,堆石体中的拱效应逐渐减弱。要减小面板浇筑后由于其下卧的堆石体流变产生的附加变形,可以尽量利用面板过水及堆石体挡水,以加快堆石体流变变形的完成。采取措施,避免大的陡坡突变以及面板浇筑时间滞后其下卧堆石体断面几个月。 相似文献
11.
根据岩土材料Merchant、Bergers和Butterfield蠕变模型的基本形式,建立3种预测混凝土面板堆石坝蠕变沉降经验模型。以蒲石河混凝土面板堆石坝为例,采用非线性有限元方法数值模拟堆石坝的顺序填筑过程。根据堆石坝沉降现场观测数据,采用回归分析方法确定3种沉降经验模型中的待定参数,确定堆石坝的蠕变沉降随时间的变化关系。工程实践应用结果表明,所提出的堆石坝蠕变沉降经验模型具有较高的拟合和预测精度,堆石坝的蠕变沉降除与时间有关之外,还与观测点的应力状态和位置以及堆石料的变形模量有关。 相似文献
12.
13.
高混凝土面板堆石坝流变的三维有限元数值模拟 总被引：4，自引：0，他引：4
采用一种新的能模拟高围压条件的堆石料幂函数流变本构模型,对水布垭面板堆石坝进行了考虑堆石料流变特性的应力-应变仿真分析。结果表明,考虑堆石料流变特性后的坝体变形有明显的增加,坝体应力有所松弛。堆石体的流变特性使得面板的挠度有所增加,面板顺坡向和坝轴向拉应力极值有所增大。对于分期浇筑面板、分期蓄水的高混凝土面板堆石坝,选用合适的流变本构模型正确地模拟堆石体的流变特性,其结果可以为大坝填筑进度及面板分期浇筑时间的确定提供参考,对于正确地预测大坝的应力变形也具有重要意义。 相似文献
14.
冻结砂土在动荷载下的蠕变特征 总被引：9，自引：3，他引：6
通过分析不同试验条件下的蠕变过程曲线,探讨了冻结砂土在动荷载下的蠕变模型,分析了最大加载应力,温度及加载频率对冻土蠕变破坏应变,破坏时间和最小蠕变速率的影响.结果表明,当最大加载应力变大时,破坏应变增加,破坏时间缩短,最小蠕变速率变快;加载条件相同时,温度越低,破坏应变越小,破坏时间越长,最小蠕变速率越小;加载频率变化时,最小蠕变速率的变化无明显规律,都在一个量级范围内,当频率变大时,最小蠕变速率略有变小的趋势.频率增加,破坏时间缩短,破坏应变减小.频率小于7Hz时,频率对破坏应变和破坏时间影响较大,而当频率大于7Hz时,随频率加快,破坏时间和破坏应变只略有减小. 相似文献
15.
粗粒料的力学特性不仅取决于应力状态,还与粗粒料本身的松密程度密切相关,即与粗粒料的材料状态相关。通过不同初始干密度的粗粒料常规大型三轴各向等压固结排水剪切试验研究了干密度对粗粒料力学特性的影响。试验结果表明：粗粒料应力-应变曲线的形态取决于密度和围压的共同作用,破坏状态之前密度和围压共同决定了粗粒料的强度和变形,而当应变足够大处于渐进状态或临界状态时,粗粒料的应力和体积应变受初始干密度的影响逐渐减小直至消失。对于软化型曲线,相变状态的应力小于渐进状态的应力,而渐进状态的应力小于破坏状态的应力。无论围压大小如何,随着初始干密度的增大,应力-应变曲线的硬化性逐渐减弱,而软化性则逐渐增强。 相似文献
16.
为合理反映颗粒破碎对堆石料力学特性的影响,基于试验结果分析,得出了堆石料在压缩和剪切作用下的颗粒破碎特性规律。通过引入压缩破碎和剪切破碎的相关参数,借鉴已有本构模型的合理定义,吸收临界状态理论和边界面理论的优点,发展了考虑颗粒破碎和状态相关的堆石料静动力统一弹塑性本构模型,并阐述了模型参数的确定方法。该模型不仅能够反映堆石料在静力荷载作用下的低压剪胀、高压剪缩、应变软化和硬化等特性,还能够反映在循环荷载作用下应力-应变的滞回特性和残余变形的累积效应。最后为验证模型的合理性,分别对堆石料的静力三轴和循环三轴试验进行了数值模拟预测,结果表明：模型预测与试验数据吻合良好,所提出的本构模型能够合理地描述颗粒破碎对堆石料静动力变形特性的影响。 相似文献
17.
High core rockfill dams exhibit complex deformation mechanisms because of complicated geological conditions, many material partitions and severe weather conditions. When realistic parameters cannot be obtained through laboratory tests or engineering analogies because of effects of size or time, back analysis is necessary to predict deformation characteristics. This paper proposes a method of deformation back analysis based on the response surface method and genetic optimization theory. The parameters of the creep and Duncan–Chang models for the Pubugou gravelly soil core rockfill dam are sequentially calculated. Back analysis performed using this method efficiently yields more precise results than those obtained from laboratory-determined parameters. 相似文献
18.
19.
This modelling study deals with the time‐dependent behaviour of rockfill media, which is of particular interest during the life of rockfill dams. Breakage of rock blocks and crack propagation are the main processes responsible for rockfill creep and collapse. The modelling procedure presented here is performed on two scales: on the rock block scale, where the grain is taken to be an assembly of rigid particles initially endowed with cohesive bonds, and on the rockfill scale, which is taken to involve a set of breakable grains interacting via contact and friction processes. The grain breakage process is described in term of a thermodynamically consistent damage interface model, where the damage is a gradual delayed process. This model was implemented in a non‐smooth contact dynamics code. The effects of the main parameters involved were analysed by performing numerical studies. The ability of the model to predict the creep behaviour of rockfill media is confirmed by presenting several simulations. Copyright © 2008 John Wiley & Sons, Ltd. 相似文献
20.
Rock fracture under upper crustal conditions is driven not only by applied stresses, but also by time-dependent, chemically activated subcritical cracking processes. These subcritical processes are of great importance for the understanding of the mechanical behaviour of rocks over geological timescales. A macroscopic manifestation of time-dependency in the brittle field is the observation that rocks can deform and fail at constant applied stresses, a phenomenon known as brittle creep. Here, we review the available experimental evidence for brittle creep in crustal rocks, and the various models developed to explain the observations. Laboratory experiments have shown that brittle creep occurs in all major rock types, and that creep strain rates are extremely sensitive to the environmental conditions: differential stress, confining pressure, temperature and pore fluid composition. Even small changes in any of these parameters produce order of magnitude changes in creep strain rates (and times-to-failure). Three main classes of brittle creep model have been proposed to explain these observations: phenomenological, statistical, and micromechanical. Statistical and micromechanical models explain qualitatively how the increasing influence of microcrack interactions and/or the increasing accumulated damage produces the observed evolution of macroscopic deformation during brittle creep. However, no current model can predict quantitatively all of the observed features of brittle creep. Experimental data are limited by the timescale over which experiments are realistically feasible. Clearly, an extension of the range of available laboratory data to lower strain rates, and the development of new modelling approaches are needed to further improve our current understanding of time-dependent brittle deformation in rocks. 相似文献