首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献，搜索用时 109 毫秒
1.
This paper describes the results of an experimental and numerical study that focused on multi‐directional behavior of unreinforced masonry walls and established the requisite of the related proposed design equations. The tests were conducted following several sets of multi‐directional loading combinations imposed on the top plane of the wall along with considering monotonic and cyclic quasi‐static loading protocols. Various boundary conditions, representing possible wall–roof connections, were also considered for different walls to investigate the influence of rotation of the top plane of the wall on the failure modes. The results of the tests were recorded with a host of high precision data acquisition systems, showing three‐dimensional displacements of a grid on the surface of the wall. Finite element models of the walls are developed using the commercial software package ABAQUS/Explicit compiled with a FORTRAN subroutine (VUMAT) written by the authors. The experimental results were then used to validate the finite element models and the developed user‐defined material models. With the utility of validated models, a parametric study was performed on a set of parameters with dominant influence on the behavior of the wall system under in‐plane and out‐of‐plane loading combinations. The experimental and numerical results are finally used to investigate the adequacy of ASCE 41 empirical equations, and some insights and recommendations are made. Copyright © 2016 John Wiley & Sons, Ltd.  相似文献   

2.
An analytical model describing the flexural response of vertically spanning out‐of‐plane loaded unreinforced masonry walls is presented in this paper. The model is based on the second‐order Euler‐Bernoulli beam theory and captures important characteristics of the out‐of‐plane response of masonry walls that have been observed in experimental tests and from numerical studies but for which an analytical solution was still lacking: the onset and the evolution of cracking, the peak strength of the out‐of‐plane loaded walls, and the softening of the response due to P ?Δ effects. The model is validated against experimental results, and the comparison shows that the model captures both the prepeak and postpeak response of the walls. From the analytical model of the force‐displacement curve, a formula for the maximum out‐of‐plane strength of the walls is derived, which can be directly applied in engineering practice.  相似文献   

3.
Eight half‐scale brick masonry walls were tested to study two important aspects of confined masonry (CM) walls related to its seismic behavior under in‐plane and out‐of‐plane loads. Four solid wall specimens tested to investigate the role of type of interface between the masonry and tie‐columns, such as toothing varying from none to every course. The other four specimens with openings were tested to study the effectiveness of various strengthening options around opening to mitigate their negative influence. In the set of four walls, one wall was infilled frame while the other three were CM walls of different configurations. The experimental results were further used to determine the accuracy of various existing models in predicting the in‐plane response quantities of CM walls. Confined masonry walls maintained structural integrity even when severely damaged and performed much better than infill frames. No significant effect of toothing details was noticed although toothing at every brick course was preferred for better post‐peak response. For perforated walls, provision of vertical elements along with continuous horizontal bands around openings was more effective in improving the overall response. Several empirical and semi‐empirical equations are available to estimate the lateral strength and stiffness of CM walls, but those including the contribution of longitudinal reinforcement in tie‐columns provided better predictions. The available equations along with reduction factors proposed for infills could not provide good estimates of strength and stiffness for perforated CM walls. However, recently proposed relations correlating strength/stiffness with the degree of confinement provided reasonable predictions for all wall specimens. Copyright © 2016 John Wiley & Sons, Ltd.  相似文献   

4.
The evaluation of the out‐of‐plane behaviour of unreinforced walls is one of the most debated topics in the seismic assessment of existing masonry buildings. The discontinuous nature of masonry and its interaction with the remainder of the building make the dynamic modelling of out‐of‐plane response troublesome. In this paper, the results of a shaking table laboratory campaign on a tuff masonry, natural scale, U‐shaped assemblage (façade adjacent to transverse walls) are presented. The tests, excited by scaled natural accelerograms, replicate the behaviour of external walls in existing masonry buildings, from the beginning of rocking motion to overturning. Two approaches have been developed for modelling the out‐of‐plane seismic behaviour: the discrete element method and an SDOF analytic model. Both approaches are shown to be capable of reproducing the experimental behaviour in terms of maximum rotation and time history dynamic response. Finally, test results and numerical time history simulations have been compared with the Italian seismic code assessment procedures. Copyright © 2011 John Wiley & Sons, Ltd.  相似文献   

5.
A simplified numerical model was used to investigate the out‐of‐plane seismic response of vertically spanning unreinforced masonry (URM) wall strips. The URM wall strips were assumed to span between two flexible diaphragms and to develop a horizontal crack above the wall mid‐height. Three degrees of freedom were used to accommodate the wall displacement at the crack height and at the diaphragm connections, and the wall dynamic stability was studied. The equations of dynamic motion were obtained using principles of rocking mechanics of rigid bodies, and the formulae were modified to include semi‐rigid wall behaviour. Parametric studies were conducted that included calculation of the wall response for different values of diaphragm stiffness, wall properties, applied overburden, wall geometry and earthquake ground motions. The results of the study suggest that stiffening the horizontal diaphragms of typical low‐rise URM buildings will amplify the out‐of‐plane acceleration demand imposed on the wall and especially on the wall–diaphragm connections. It was found that upper‐storey walls connected to two flexible diaphragms had reduced stability for applied earthquake accelerograms having dominant frequency content that was comparable with the frequency of the diaphragms. It was also found that the applied overburden reduced wall stability by reducing the allowable wall rotations. The results of this study suggest that the existing American Society of Civil Engineers recommendations for assessment of vertically spanning walls overestimate the stability of top‐storey walls in multi‐storey buildings in high‐seismic regions or for walls connected to larger period (less stiff) diaphragms. Copyright © 2015 John Wiley & Sons, Ltd.  相似文献   

6.
A computational model for evaluating the dynamical response and the damage of large masonry walls subjected to out‐of‐plane seismic actions is presented. During earthquakes, these actions are often the main cause of damage for the front wall and lateral walls of old masonry‐built churches and monuments. Since the crack patterns often tend to subdivide the plane walls into a number of blocks, the model assumes such walls as a series of quadrilateral plane rigid elements connected to each other in the middle of their adjoining sides. Only the out‐of‐plane displacements are considered, and the connections are regarded as spherical elasto‐plastic joints which allow rotations whose axis is in the plane of the undeformed wall. The hysteretic characteristics of these joints are defined so as to approximate the brittle behaviour of masonry material and the degradation due to cyclic loadings. The numerical results obtained using a limited number of elements show that the global out‐of‐plane response of the masonry walls and the mechanical degradation at each connection are in accord with the observed behaviour of real churches hit by strong earthquakes. Copyright © 2000 John Wiley & Sons, Ltd.  相似文献   

7.
Seismic assessment of existing unreinforced masonry buildings represents a current challenge in structural engineering. Many historical masonry buildings in earthquake regions were not designed to withstand seismic loading; thus, these structures often do not meet the basic safety requirements recommended by current seismic codes and need to be strengthened considering the results from realistic structural analysis. This paper presents an efficient modelling strategy for representing the nonlinear response of unreinforced masonry components under in‐plane cyclic loading, which can be used for practical and accurate seismic assessment of masonry buildings. According to the proposed strategy, generic masonry perforated walls are modelled using an equivalent frame approach, where each masonry component is described utilising multi‐spring nonlinear elements connected by rigid links. When modelling piers and spandrels, nonlinear springs are placed at the two ends of the masonry element for describing the flexural behaviour and in the middle for representing the response in shear. Specific hysteretic rules allowing for degradation of stiffness and strength are then used for modelling the member response under cyclic loading. The accuracy and the significant potential of the proposed modelling approach are shown in several numerical examples, including comparisons against experimental results and the nonlinear dynamic analysis of a building structure. Copyright © 2016 John Wiley & Sons, Ltd.  相似文献   

8.
Most of the studies related to the modeling of masonry structures have by far investigated either the in‐plane (IP) or the out‐of‐plane (OP) behavior of walls. However, seismic loads mostly impose simultaneous IP and OP demands on load‐bearing or shear masonry walls. Thus, there is a need to reconsider design equations of unreinforced masonry walls by taking into account bidirectional effects. The intent of this study is to investigate the bidirectional behavior of an unreinforced masonry wall with a typical aspect ratio under different displacement‐controlled loading directions making use of finite element analysis. For this purpose, the numerical procedure is first validated against the results of the tests on walls with different failure modes conducted by the authors. Afterward, the response of the wall systems is evaluated with increasing top displacement having different orientations. A set of 19 monotonic and three cyclic loading analyses are performed, and the results are discussed in terms of the variation of failure modes and load–displacement diagrams. Moreover, the results of wall capacity in each loading condition are compared with those of the ASCE41‐06 formulations. The results indicate that the direction of the resultant force, vectorial summation of IP and OP forces, of the wall is initially proportional to the ratio of stiffness in the IP and the OP directions. However, with the increase of damage, the resultant force direction inclines towards the wall's longitudinal direction regardless of the direction of the imposed displacement. Finally, recommendations are made for applicability of ASCE41‐06 formulations under different bidirectional loading conditions. Copyright © 2014 John Wiley & Sons, Ltd.  相似文献   

9.
The response of calcium silicate unreinforced masonry construction to horizontal cyclic loading has recently become the focus of experimental and numerical research, given its extensive use in some areas of the world that are now exposed to induced earthquakes (eg, north of the Netherlands). To assess the seismic behaviour of such construction, a relatively wide range of modelling methodologies are available, amongst which the discrete elements approach, which takes into account the intrinsic heterogeneity of a brick‐mortar assembly, can probably be deemed as the most appropriate computational procedure. On the other hand, however, since discrete elements numerical methods are based on a discontinuum domain, often they are not able to model every stage of the structural response adequately, and because of the high computational burden required, the analysis scale should be chosen carefully. The applied element method is a relatively recent addition to the discrete elements family, with a high potential for overcoming the aforementioned limitations or difficulties. Initially conceived to model blast events and concrete structures, its use in the earthquake engineering field is, of late, increasing noticeably. In this paper, the use of the applied element method to model the in‐plane cyclic response of calcium silicate masonry walls is discussed and scrutinised, also through the comparison with experimental results of in‐plane cyclic shear‐compression tests on unreinforced masonry walls.  相似文献   

10.
A simple constitutive model is proposed for an in‐plane numerical analysis of unreinforced masonry structures, which are subject to cyclic loading, by using explicit dynamic procedures. The proposed model is implemented by using two‐dimensional plane‐stress finite elements. Three different constitutive relations that are based on the total strain in the global material system are used. Cracking and crushing are controlled through normal strains, whereas shear is controlled through shear strain. Separate hysteretic rules are adopted for each mode of damage. A numerical analysis of masonry walls that are subject to cyclic loading has demonstrated that the use of explicit procedures in conjunction with the proposed model results in an acceptable accuracy when compared with the experimental results. Copyright © 2010 John Wiley & Sons, Ltd.  相似文献   

11.
This paper addresses the problem of assessing the seismic resistance of brick masonry walls subject to out‐of‐plane bending. A simplified linearized displacement‐based procedure is presented along with recommendations for the selection of an appropriate substitute structure in order to provide the most representative analytical results. A trilinear relationship is used to characterize the real nonlinear force–displacement relationship for unreinforced brick masonry walls. Predictions of the magnitude of support motion required to cause flexural failure of masonry walls using the linearized displacement‐based procedure and quasi‐static analysis procedures are compared with the results of experiments and non‐linear time‐history analyses. The displacement‐based procedure is shown to give significantly better predictions than the force‐based method. Copyright © 2002 John Wiley & Sons, Ltd.  相似文献   

12.
This article presents a new mechanical model for the non‐linear force–displacement response of unreinforced masonry (URM) walls developing a flexural rocking mode including their displacement capacity. The model is based on the plane‐section hypothesis and a constitutive law for the masonry with zero tensile strength and linear elastic behaviour in compression. It is assumed that only the compressed part of the wall contributes to the stiffness of the wall and therefore the model accounts for a softening of the response due the reduction of the effective area. Stress conditions for limit states are proposed that characterise the flexural failure. The new model allows therefore linking local performance levels to global displacement capacities. The limit states criteria describe the behaviour of modern URM walls with cement mortar of normal thickness and clay bricks. The model is validated through comparison of local and global engineering demand parameters with experimental results. It provides good prediction of the effective stiffness, the force capacity and the displacement capacity of URM walls at different limit states. Copyright © 2015 John Wiley & Sons, Ltd.  相似文献   

13.
Seismic response of unreinforced masonry (URM) buildings is largely influenced by nonlinear behavior of spandrels, which provide coupling between piers under in‐plane lateral actions. Seismic codes do not appropriately address modeling and strength verification of spandrels, adapting procedures originally proposed for piers. Therefore, research on spandrels has received significant attention in some earthquake‐prone countries, such as Italy and New Zealand. In the last years, the authors of this paper have performed both monotonic and cyclic in‐plane lateral loading tests on full‐scale masonry walls with single opening and different spandrel types. Those tests were carried out in a static fashion and with displacement control. In this paper, experimental outcomes for two as‐built specimens are presented and compared with those obtained in the past for another as‐built specimen with a wooden lintel above the opening. In both newly tested specimens, the masonry above the opening was supported by a shallow masonry arch. In one of those specimens, a reinforced concrete (RC) bond beam was realized on top of the spandrel, resulting in a composite URM‐RC spandrel. Then, the influence of spandrel type is analyzed in terms of observed damage, force–drift curves, and their bilinear idealizations, which allowed to compare displacement ductility and overstrength of wall specimens. Furthermore, effects of rocking behavior of piers are identified, highlighting their relationship with hysteretic damping and residual drifts. Copyright © 2014 John Wiley & Sons, Ltd.  相似文献   

14.
Displacement‐based assessment procedures require as input reliable estimates of the deformation capacity of all structural elements. For unreinforced masonry (URM) walls, current design codes specify the in‐plane deformation capacity as empirical equations of interstory drift. National codes differ with regard to the parameters that are considered in these empirical drift capacity equations, but the inhomogeneity of datasets on URM wall tests renders it difficult to validate the hypotheses with the currently available experimental data. This paper contributes to the future development of such empirical relationships by investigating the sensitivity of the drift capacity to the shear span, the aspect ratio, the axial load ratio, and the size of the wall. For this purpose, finite element models of URM walls are developed in Abaqus/Explicit and validated against a set of experimental results. The results show that the axial load ratio, the shear span, and the wall size are among the factors that influence the drift capacity the most. Empirical equations are mainly derived from test results on small walls, and the numerical results suggest that this can lead to a significant overestimation of the drift capacity for larger walls.  相似文献   

15.
An experimental programme was conducted in which eight full‐scale unreinforced masonry walls were subjected to cyclic face loading using a system of airbags. Of the eight walls, six contained a window opening and four were subjected to vertical pre‐compression. Combined supports at the vertical and horizontal edges ensured that under face loading the walls underwent two‐way bending. The test walls were found to possess good post‐peak strength and displacement capacity as well as reasonable energy dissipation characteristics. Significant strength and stiffness degradation and non‐symmetry of strength in the positive and negative displacement directions were also evident. Discussion of the causes of the aforementioned trends and their implications towards the seismic response of masonry walls is provided. Copyright © 2006 John Wiley & Sons, Ltd.  相似文献   

16.
This paper presents the findings of shaking‐table experiments conducted to examine the out‐of‐plane seismic performance of masonry veneer walls. Seven wall assemblies were tested, each consisting of a clay masonry veneer anchored to a wood‐stud backing. Design variables include the type of veneer ties, tie spacing, and presence or absence of mortar joint reinforcement and window opening. The walls were designed and constructed in accordance with current US code provisions. Results of the experiments show that failure of the corrugated ties is governed by pullout of the nails from the wood studs, while failure of the rigid ties is governed by detachment from the mortar joints or pull‐through of the screw heads through fastener holes. Both types of ties show satisfactory performance under ground motions corresponding to Design Basis and Maximum Considered Earthquakes representative of Seismic Design Category E. Although the rigid ties were stronger than the corrugated ties, they had wider vertical spacing and failed at a slightly higher seismic load. Observed extraction capacities of the nails show high variability, which merits attention. Joint reinforcement did not show any noticeable effect on the out‐of‐plane behavior of the veneer. Results of an analytical study have shown that the detachment of a veneer from the backing system is preceded by veneer cracking, which influences the distribution of tie forces, and that the vertical tie spacing influences the cracking load for the veneer. Copyright © 2010 John Wiley & Sons, Ltd.  相似文献   

17.
In this paper, a technique is presented which employs the results of pseudo‐dynamic tests for the development of a mathematical model. This technique, described by means of the mathematical modelling of a three‐storey reinforced concrete frame building with infill in the bottom two storeys, which was tested at ELSA in Ispra, proved to be effective and to lead to a fairly accurate structural model. The results of analyses suggest that the global non‐linear seismic response of reinforced concrete frames with masonry infill can be adequately simulated by a relatively simple mathematical model, which combines beam elements with concentrated plasticity, simple connection elements, and equivalent strut elements representing the infill walls (provided that the infill does not fail out of plane and that no shear sliding failure occurs). Copyright © 2002 John Wiley & Sons, Ltd.  相似文献   

18.
The evaluation of the dynamic behaviour of rocking elements is directly correlated to the energy dissipated because of the impacts at the base interface, which can be represented by means of a coefficient of restitution. This schematization is commonly accepted as representative of the out‐of‐plane response of stone masonry walls. An experimental campaign (in a lab environment) aiming at assessing the value of this coefficient for a sacco granite masonry wall is presented in this work. The rocking motion at a predefined bed joint level was induced in the tested specimens in order to validate a novel test setup designed to assess the coefficient of restitution value by means of a realistic reproduction of the rocking behaviour of a single element, under the hypothesis of an infinitely stiff system above the bed joint level. As the main objective of the work was to assess the rocking behaviour of a masonry wall that looses energy at the impacts at a certain joint level, the flexural behaviour was not desirable and had to be avoided. For this purpose, a test setup based on the equivalent block approach was developed. In the final section of this work, comparisons between experimental and numerical results are presented together with some preliminary conclusions on the appropriate modelling strategy and the values of the coefficient of restitution to be used for the seismic assessment of the out‐of‐plane rocking behaviour of this type of sacco stone masonry walls. Copyright © 2013 John Wiley & Sons, Ltd.  相似文献   

19.
The paper proposes a systematic comparison between two methods of analysis that are well established in the field of earthquake engineering: nonlinear dynamic analysis and nonlinear static procedure (NSP), applied to the out‐of‐plane seismic response of two masonry façades representative of many ancient Italian churches. The comparison is based on extensive numerical analyses, which focus on the flexural and torsional mechanisms, while the in‐plane damage mechanisms and the possible detachment between the façade and the lateral walls because of a poor connection have been presently disregarded. The computations, both in the static and in the dynamic field, are based on a rigid body and spring model specifically implemented for this issue, computationally efficient and equipped with a realistic model of damage and hysteresis at the mesoscale. An innovative aspect of this study is the heuristic modelling of three‐wythe masonry, to include some typical texture effects on the macroscale nonlinear response. For each façade, two different masonry textures were considered, performing extensive dynamic analyses that offered a detailed overview about the performance under earthquakes of different intensities. In parallel, NSP and the classical N2‐based seismic assessment were applied. A critical discussion and comparison of the results of the two methods is presented to rationally appraise limits and opportunities. In particular, flexural and twisting out‐of‐plane mechanisms were clearly appraised in the dynamic field, whereas NSPs were not always able to describe the collapse, because they missed the partial failures determined by higher vibration modes, as could be expected. Copyright © 2012 John Wiley & Sons, Ltd.  相似文献   

20.
There are numerous studies on the behavior of Unreinforced Masonry (URM) walls in both in‐plane (IP) and out‐of‐plane (OP) directions; however, few aimed at understanding the simultaneous contribution of these intrinsic responses during earthquakes. Undoubtedly, even a strong URM wall shows weakened capacity in the OP direction because of minor cracks and other damages in the IP direction, and this capacity reduction has not yet been accounted for in seismic codes. In this study, performance of three URM walls is evaluated by several numerical analyses in terms of the OP capacity reduction because of IP displacements and failure modes. Several parameters influencing the OP capacity have been studied including aspect ratio, roof boundary condition, IP displacement and IP loading patterns. The results indicate that reduction in the OP capacity of URM walls varies from negligible to very high depending on boundary conditions, IP failure mode and IP damage severity. Moreover, IP loading pattern is more important in walls with higher aspect ratios because of their IP failure modes. Copyright © 2015 John Wiley & Sons, Ltd.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号