首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献，搜索用时 62 毫秒
1.
Two reaches of Aguapeí River, a left‐bank tributary of the Paraná River in western São Paulo state, Brazil, were studied with the objective of assessing the role of bend curvature on channel migration in this wet‐tropical system and examining if land‐use changes or ENSO (El Niño Southern Oscillation) driven climate anomalies over nearly half a century have changed migration behaviour and planform geometry. Meander‐bend migration rates and morphometric parameters including meander‐bend curvature, sinuosity, meander wavelength and channel width, were measured and the frequency of bend cutoffs was analysed in order to determine the rate of change of channel adjustment over a 48 year period to 2010. Results show that maximum average channel migration rates occur in bends with curvatures of about 2–3 rc/w, similar to other previously studied temperate and subarctic freely meandering rivers although not as pronounced and with a tendency to favour tighter curvature. From 1962 to 2010 the Aguapeí River has undergone a significant reduction in sinuosity, a shift from tightly curving to more open bends, an overall decline in channel migration rates, an associated decrease in the frequency of neck‐cutoffs and an overall increase in channel width. As the majority of the drainage basin (96%) was already deforested in 1962, channel form and process changes were, unlike an interpretation for an adjacent river system, not attributed to altered land‐use but rather to a sharp ENSO‐driven increase in the magnitude of peak flow‐discharges of some 32% since 1972. In summary, this research revealed that recent climate and associated flow regime changes are having a pronounced effect on river channel behaviour in the Aguapeí River investigated here. Copyright © 2018 John Wiley & Sons, Ltd.  相似文献   

2.
In meandering rivers, the local channel migration rate increases with increasing bend sharpness until it reaches a maximum at a certain critical value of the bend sharpness. Beyond this critical value, the migration rate decreases if bend sharpness increases. Similarly, reach‐averaged migration rates attain a maximum at a certain river sinuosity. This work investigates the physics of these phenomena by comparing the results of two physics‐based models of different complexity, in which the migration rates are proportional to the near‐bank flow velocity excess. In the computational tests the river was allowed to meander progressively, starting from an almost straight planimetry. Both models reproduced the observed peak in the curve describing the local migration rate as a function of the ratio radius of curvature‐channel width (R/B), with a rising limb at lower R/B values and a falling limb at higher R/B values. The rising limb can be explained by the decrease in relative lag distance between near‐bank flow velocity and forcing curvature as R/B increases. The falling limb results from the decrease in local channel curvature and near‐bank flow velocity excess. Since the models do not include flow separation, the results indicate that this phenomenon is not needed to explain the decrease of channel migration rates in sharp bends. The models reproduced also the peak in the curve describing the reach‐averaged migration rates as a function of river sinuosity The increase and then decrease of reach‐averaged migration rates as sinuosity increases appears to be mainly caused by the variation of the reach‐averaged value of the ratio R/B. Copyright © 2009 John Wiley & Sons, Ltd.  相似文献   

3.
The Gediz (Ala?ehir) Graben is located in the highly tectonically active and seismogenic region of Western Turkey. The rivers upstream of the normal fault‐bounded graben each contain a non‐lithologic knickpoint, including those that drain through inferred fault segment boundaries. Knickpoint heights measured vertically from the fault scale with footwall relief and documented fault throw (vertical displacement). Consequently, we deduce these knickpoints were initiated by an increase in slip rate on the basin‐bounding fault, driven by linkage of the three main fault segments of the high‐angle graben bounding fault array. Fault interaction theory and ratios of channel steepness suggest that the slip rate enhancement factor on linkage was a factor of 3. We combine this information with geomorphic and structural constraints to estimate that linkage took place between 0.6 Ma and 1 Ma. Calculated pre‐ and post‐linkage throw rates are 0.6 and 2 mm/yr respectively. Maximum knickpoint retreat rates upstream of the faults range from 4.5 to 28 mm/yr, faster than for similar catchments upstream of normal faults in the Central Apennines and the Hatay Graben of Turkey, and implying a fluvial landscape response time of 1.6 to 2.7 Myr. We explore the relative controls of drainage area and precipitation on these retreat rates, and conclude that while climate variation and fault throw rate partially explain the variations seen, lithology remains a potentially important but poorly characterised variable. Copyright © 2016 John Wiley & Sons, Ltd.  相似文献   

4.
The process of channelization on river floodplains plays an essential role in regulating river sinuosity and creating river avulsions. Most channelization occurs within the channel belt (e.g. chute channels), but growing evidence suggests some channels originate outside of the channel‐belt in the floodplain. To understand the occurrence and prevalence of these floodplain channels we mapped 3064 km2 of floodplain in Indiana, USA using 1.5 m resolution digital elevation models (DEMs) derived from airborne light detection and ranging (LiDAR) data. We find the following range of channelization types on floodplains in Indiana: 6.8% of floodplain area has no evidence of channelization, 55.9% of floodplains show evidence (e.g. oxbow lakes) of chute‐channel activity in the channel belt, and 37.3% of floodplains contain floodplain channels that form long, coherent down‐valley pathways with bifurcations and confluences, and they are active only during overbank discharge. Whereas the first two types of floodplains are relatively well studied, only a few studies have recognized the existence of floodplain channels. To understand why floodplain channels occur, we compared the presence of channelization types with measured floodplain width, floodplain slope, river width, river meander rate, sinuosity, flooding frequency, soil composition, and land cover. Results show floodplain channels occur when the fluvial systems are characterized by large floodplain‐to‐river widths, relatively higher meandering rates, and are dominantly used for agriculture. More detailed reach‐scale mapping reveals that up to 75% of channel reaches within floodplain channels are likely paleo‐meander cutoffs. The meander cutoffs are connected by secondary channels to form floodplain channels. We suggest that secondary channels within floodplains form by differential erosion across the floodplain, linking together pre‐existing topographic lows, such as meander cutoffs. Copyright © 2016 John Wiley & Sons, Ltd.  相似文献   

5.
We develop a new method for analysis of meandering channels based on planform sinuosity. This analysis objectively identifies three channel‐reach lengths based on sinuosity measured at those lengths: the length of typical, simple bends; the length of long, often compound bends; and the length of several bends in sequence that often evolve from compound bends to form multibend loops. These lengths, when normalized by channel width, tend to fall into distinct and clustered ranges for different natural channels. Mean sinuosity at these lengths also falls into distinct ranges. That range is largest for the third and greatest length, indicating that, for some streams, multibend loops are important for planform sinuosity, whereas for other streams, multibend loops are less important. The role of multibend loops is seldom addressed in the literature, and they are not well predicted by previous modelling efforts. Also neglected by previous modelling efforts is bank–flow interaction and its role in meander evolution. We introduce a simple river meandering model based on topographic steering that has more in common with cellular approaches to channel braiding and landscape evolution modelling than to rigorous, physics‐based analyses of river meandering. The model is sufficient to produce reasonable meandering channel evolution and predicts compound bend and multibend loop formation similar to that observed in nature, in both mechanism and importance for planform sinuosity. In the model, the tendency to form compound bends is sensitive to the relative magnitudes of two lengths governing meander evolution: (i) the distance between the bend cross‐over and the zone of maximum bank shear stress, and (ii) the bank shear stress dissipation length related to bank roughness. In our simple model, the two lengths are independent. This sensitivity implies that the tendency for natural channels to form compound bends may be greater when the banks are smoother. Copyright © 2002 John Wiley & Sons, Ltd.  相似文献   

6.
Hydraulic interactions between rivers and floodplains produce off‐channel chutes, the presence of which influences the routing of water and sediment and thus the planform evolution of meandering rivers. Detailed studies of the hydrologic exchanges between channels and floodplains are usually conducted in laboratory facilities, and studies documenting chute development are generally limited to qualitative observations. In this study, we use a reconstructed, gravel‐bedded, meandering river as a field laboratory for studying these mechanisms at a realistic scale. Using an integrated field and modeling approach, we quantified the flow exchanges between the river channel and its floodplain during an overbank flood, and identified locations where flow had the capacity to erode floodplain chutes. Hydraulic measurements and modeling indicated high rates of flow exchange between the channel and floodplain, with flow rapidly decelerating as water was decanted from the channel onto the floodplain due to the frictional drag provided by substrate and vegetation. Peak shear stresses were greatest downstream of the maxima in bend curvature, along the concave bank, where terrestrial LiDAR scans indicate initial floodplain chute formation. A second chute has developed across the convex bank of a meander bend, in a location where sediment accretion, point bar development and plant colonization have created divergent flow paths between the main channel and floodplain. In both cases, the off‐channel chutes are evolving slowly during infrequent floods due to the coarse nature of the floodplain, though rapid chute formation would be more likely in finer‐grained floodplains. The controls on chute formation at these locations include the flood magnitude, river curvature, floodplain gradient, erodibility of the floodplain sediment, and the flow resistance provided by riparian vegetation. Copyright © 2015 John Wiley & Sons, Ltd.  相似文献   

7.
Meander bends in alluvial rivers morphologically evolve towards meander cut‐off with narrowing intra‐meander necks, and this should steepen hydraulic gradients and intensify intra‐meander hyporheic flux. This research used dye tracking and head loss measurements in a 1 : 500 planimetrically scaled laboratory river table to quantify the spatial and temporal intensification of intra‐meander flux rates at two evolution ages. The younger meander bend, M1, had a sinuosity of 2.3, a river neck width of 0.39 cm, and 0.6% river slope, and the older meander bend, M3, had a sinuosity of 5.2, a river neck width of 0.12 cm, and 0.5% river slope. Flux into and out of the meander bend was estimated along the normalized curvilinear distance s*, with the meander neck at s* = 0.1 and s* = 0.9, the meander centroid at s* = 0.37 and s* = 0.63, and the apex at s* = 0.5. Between the meander centroid and neck, we documented a 60% spatial intensification for M1 and a 90% spatial intensification for M3. Between M1 and M3, we documented a 135% temporal intensification at the neck and a 100% intensification at the centroid. Our empirical spatial and temporal intensification rates involving the M1 and the M3 scenario were one to three times lower than theoretical rates derived from a river evolution model with equivalent M1 and M3 planimetry. Overestimation by the theoretical model was attributed to exaggerated head loss caused by the model neglecting groundwater contributions to river stage. Hyporheic exchange provides critical ecosystem services, and its spatial and temporal variation with meander evolution should be considered in river management. Copyright © 2012 John Wiley & Sons, Ltd.  相似文献   

8.
Haiyan Yang 《水文研究》2020,34(17):3702-3717
Gravel-bed braided rivers are highly energetic fluvial systems characterized by frequent in-channel avulsions, which govern the morphodynamics of such rivers and are essential for them to maintain a braided planform. However, the avulsion mechanisms within natural braided rivers remain unclear due to their complicated hydraulic and morphodynamic processes. Influenced by neighbouring channels, avulsions in braided rivers may differ from those of bifurcations in single-thread rivers, suggesting that avulsions should be studied within the context of the entire braid network. In this study, braiding evolution processes in gravel-bed rivers were simulated using a physics-based numerical model that considers graded bed-load transport by dividing sediment particles into multiple size fractions and vertical sediment sorting by dividing the riverbed into several vertical layers. The numerical model successfully produced braiding processes and avulsion activities similar to those observed in a laboratory river. Results show that bend evolution of the main channel was the fundamental process controlling the occurrence of avulsions in the numerical model, with a cyclic process of channel meandering by lateral migration that transitioned to a straight channel pattern by avulsion. The radius of bend curvature for triggering avulsions in the numerical model was measured and it was found that the highest probability for a channel bend to generate an avulsion occurs when its radius of curvature is approximately 2.0–3.3 times the average anabranch width. Other types of avulsion were also observed that did not occur specifically at meander bends, but upstream meander evolution indirectly influenced such avulsions by altering channel pattern and discharge to those locations. This study explored the processes and mechanisms of several types of avulsion, and proposed factors controlling their occurrence, namely increasing channel curvature, high shear stress, tributary discharge, riverbed gradient and upstream channel pattern, with high shear stress being a direct indicator. Furthermore, avulsions in a typical gravel-bed braided river, the Waimakariri River in New Zealand, were analysed using sequential Google Earth maps, which confirmed the conclusions derived from the numerical simulation.  相似文献   

9.
In meandering rivers cut into bedrock, erosion across a channel cross‐section can be strongly asymmetric. At a meander apex, deep undercutting of the outer bank can result in the formation of a hanging cliff (which may drive hillslope failure), whereas the inner bank adjoins a slip‐off slope that connects to the hillslope itself. Here we propose a physically‐based model for predicting channel planform migration and incision, point bar and slip‐off slope formation, bedrock abrasion, the spatial distribution of alluvial cover, and adaptation of channel width in a mixed bedrock‐alluvial channel. We simplify the analysis by considering a numerical model of steady, uniform bend flow satisfying cyclic boundary conditions. Thus in our analysis, ‘sediment supply’, i.e. the total volume of alluvium in the system, is conserved. In our numerical simulations, the migration rate of the outer bank is a specified parameter. Our simulations demonstrate the existence of an approximate state of dynamic equilibrium corresponding to a near‐solution of permanent form in which a bend of constant curvature, width, cross‐sectional shape and alluvial cover distribution migrates diagonally downward at constant speed, leaving a bedrock equivalent of a point bar on the inside of the bend. Channel width is set internally by the processes of migration and incision. We find that equilibrium width increases with increasing sediment supply, but is insensitive to outer bank migration rate. The slope of the bedrock point bar varies inversely with both outer bank migration rate and sediment supply. Although the migration rate of the outer bank is externally imposed here, we discuss a model modification that would allow lateral side‐wall abrasion to be treated in a manner similar to the process of bedrock incision. Copyright © 2016 John Wiley & Sons, Ltd.  相似文献   

10.
A depth‐averaged linearized meander evolution model was calibrated and tested using the field data collected at the Quinn River in the Black Rock Desert, Nevada. Two approaches used to test the model were: (1) simulating meander evolution and comparing the results with the observed 38 year migration pattern; and (2) fitting the model parameters to present bank asymmetry (the ratio of the maximum bank gradients on opposite sides of the channel). The data required as input were collected in the field during a high flow in May 2011 and from aerial photographs and LiDAR data. Both approaches yielded similar results for the best fit parameter values. The bank asymmetry analysis showed that the bank asymmetry and the velocity perturbation have high correlation at close to zero spatial lag while the maximum correlation between the bank asymmetry and maximum bend curvature is offset by about 25 m. The model sufficiently replicated 38 years of channel migration, with a few locations significantly under‐ or over‐predicted. Inadequacies of the flow model and/or variation in bank properties unaccounted for are most likely the causes for these discrepancies. Flow through the Quinn River was also simulated by a more general 3D model. The downstream pattern of near‐bank shear stresses simulated by the 3D model is nearly identical to those resulting from the linearized flow model. Topographic profiles across interior bends are essentially invariant over a wide range of migration rates, suggesting that the traditional formulation that cut bank erosion processes govern migration rates is appropriate for the Quinn River. Copyright © 2014 John Wiley & Sons, Ltd.  相似文献   

11.
Accurately measuring river meander migration over time is critical for sediment budgets and understanding how rivers respond to changes in hydrology or sediment supply. However, estimates of meander migration rates or streambank contributions to sediment budgets using repeat aerial imagery, maps, or topographic data will be underestimated without proper accounting for channel reversal. Furthermore, comparing channel planform adjustment measured over dissimilar timescales are biased because short- and long-term measurements are disproportionately affected by temporary rate variability, long-term hiatuses, and channel reversals. We evaluate the role of timescale dependence for the Root River, a single threaded meandering sand- and gravel-bedded river in southeastern Minnesota, USA, with 76 years of aerial photographs spanning an era of landscape changes that have drastically altered flows. Empirical data and results from a statistical river migration model both confirm a temporal measurement-scale dependence, illustrated by systematic underestimations (2–15% at 50 years) and convergence of migration rates measured over sufficiently long timescales (> 40 years). Frequency of channel reversals exerts primary control on measurement bias for longer time intervals by erasing the record of observable migration. We conclude that using long-term measurements of channel migration for sediment remobilization projections, streambank contributions to sediment budgets, sediment flux estimates, and perceptions of fluvial change will necessarily underestimate such calculations. © 2019 John Wiley & Sons, Ltd.  相似文献   

12.
In gravel‐bed rivers with well‐de?ned pool–bar morphology, the path length of transported bed particles must be, at least during ‘channel‐forming’ ?ows, equal to the length scale of the morphology. This is the basis for some methods for estimating bed material transport rates. However, previous data, especially from ?eld tests, are often strongly positively skewed with mean much shorter than the pool–bar spacing. One possible explanation is that positively skewed distributions occur only in channels lacking distinct pool–bar topography or only at lower discharges in pool–bar channels. A series of ?ume experiments using ?uorescent tracers was used to measure path length distributions in low‐sinuosity meandering channels to assess the relation with channel morphology and ?ow conditions. At channel‐forming ?ows, 55 to 75 per cent of the tracer grains were deposited on the ?rst point bar downstream of the point of tracer input, with 15 per cent passing beyond the ?rst bar. Path length distributions are symmetrical with mean equal to the pool–bar spacing and can be described with a Cauchy distribution. In some cases there was a secondary mode close to the point of tracer introduction; this bimodal distribution ?ts a combined gamma–Cauchy distribution. Only when discharge was reduced below the channel‐forming ?ow were frequency distributions unimodal and positively skewed with no relation to the pool–bar spacing. Thus, path length distributions become more symmetrical, and mean path length increases to coincide with pool–bar spacing, as ?ow approaches channel‐forming conditions. This is a substantial modi?cation of existing models of particle transfer in gravel‐bed rivers. Copyright © 2003 John Wiley & Sons, Ltd.  相似文献   

13.
Sedimentary architecture of abandoned channel fills   总被引：1，自引：0，他引：1  
  相似文献   

14.
Meandering channels and valleys are dominant landscape features on Earth. Their morphology and remnants potentially indicate past base-level fluctuations and changing regional slopes. The prevailing presence of meandering segments in low-slope areas somewhat confuses the physically based relationships between slope and channel meandering. This relationship underlies a fundamental debate: do incised sinuous channels actively develop during steepening of a regional slope, or do they inherit the planform of a preexisting sinuous channel through vertical incision? This question was previously explored through reconstructed evolution of meandering rivers, numerical simulations, and controlled, scaled-down laboratory experiments. Here, we study a rare, field-scale set of a dozen adjacent perennial channels, evolving in recent decades in a homogeneous erodible substrate in response to the Dead Sea level fall (> 30 m over 40 years). These channels are fed by perennial springs and have no drainage basin or previous fluvial history; they initiated straight and transformed into incising meandering channels following the emergence of the preexisting lake bathymetry, which resulted in increased channel lengths and regional slopes at different rates for each channel. This field setting allows testing the impact of changing regional slope on the sinuosity of a stream in the following cases: (a) relatively long and low-gradient shelf-like margins, (b) a sharp increase in the basinward gradient at the shelf-slope transition, and (c) gradually steepening slopes. Under a stable and low valley slope, the channels mainly incise vertically, inheriting a preexisting sinuous pattern. When the regional slope steepens, the channels start to meander, accompanying the vertical incision. The highest sinuosity evolved in the steepest channel, which also developed the deepest and widest valley. These results emphasize the amplifying impact of steepening regional slope on sinuosity. This holds when the flow is confined and chute cutoffs are scarce.  相似文献   

15.
Reduced‐complexity models of fluvial processes use simple rules that neglect much of the underlying governing physics. This approach is justified by the potential to use these models to investigate long‐term and/or fundamental river behaviour. However, little attention has been given to the validity or realism of reduced‐complexity process parameterizations, despite the fact that the assumptions inherent in these approaches may limit the potential for elucidating the behaviour of natural rivers. This study presents two new reduced‐complexity flow routing schemes developed specifically for application in single‐thread rivers. Output from both schemes is compared with that from a more sophisticated model that solves the depth‐averaged shallow water equations. This comparison provides the first demonstration of the potential for deriving realistic predictions of in‐channel flow depth, unit discharge, energy slope and unit stream power using simple flow routing schemes. It also highlights the inadequacy of modelling unit stream power, shear stress or sediment transport capacity as a function of local bed slope, as has been common practice in a number of previous reduced‐complexity models. Copyright © 2009 John Wiley & Sons, Ltd.  相似文献   

16.
Compound meander bends with multiple lobes of maximum curvature are common in actively evolving lowland rivers. Interaction among spatial patterns of mean flow, turbulence, bed morphology, bank failures and channel migration in compound bends is poorly understood. In this paper, acoustic Doppler current profiler (ADCP) measurements of the three‐dimensional (3D) flow velocities in a compound bend are examined to evaluate the influence of channel curvature and hydrologic variability on the structure of flow within the bend. Flow structure at various flow stages is related to changes in bed morphology over the study timeframe. Increases in local curvature within the upstream lobe of the bend reduce outer bank velocities at morphologically significant flows, creating a region that protects the bank from high momentum flow and high bed shear stresses. The dimensionless radius of curvature in the upstream lobe is one‐third less than that of the downstream lobe, with average bank erosion rates less than half of the erosion rates for the downstream lobe. Higher bank erosion rates within the downstream lobe correspond to the shift in a core of high velocity and bed shear stresses toward the outer bank as flow moves through the two lobes. These erosion patterns provide a mechanism for continued migration of the downstream lobe in the near future. Bed material size distributions within the bend correspond to spatial patterns of bed shear stress magnitudes, indicating that bed material sorting within the bend is governed by bed shear stress. Results suggest that patterns of flow, sediment entrainment, and planform evolution in compound meander bends are more complex than in simple meander bends. Moreover, interactions among local influences on the flow, such as woody debris, local topographic steering, and locally high curvature, tend to cause compound bends to evolve toward increasing planform complexity over time rather than stable configurations. Copyright © 2016 John Wiley & Sons, Ltd.  相似文献   

17.
Field measurements and morphodynamic simulations were carried out along a 5‐km reach of the sandy, braided, lower Tana River in order to detect temporal and spatial variations in river bed modifications and to determine the relative importance of different magnitude discharges on river bed and braid channel evolution during a time span of one year, i.e. 2008–2009. Fulfilling these aims required testing the morphodynamic model's capability to simulate changes in the braided reach. We performed the simulations using a 2‐D morphodynamic model and different transport equations. The survey showed that more deposition than erosion occurred during 2008–2009. Continuous bed‐load transport and bed elevation changes of ±1 m, and a 70–188‐m downstream migration of the thalweg occurred. Simulation results indicated that, during low water periods, modifications occurred in both the main channel and in other braid channels. Thus, unlike some gravel‐bed rivers, the sandy lower Tana River does not behave like a single‐thread channel at low discharge. However, at higher discharge, i.e. exceeding 497 m3/s, the river channel resembled a single‐thread channel when channel banks confined the flow. Although the spring discharge peaks caused more rapid modifications than slower flows, the cumulative volumetric changes of the low water period were greater. The importance of low water period flows for channel modifications is emphasized. Although the 2‐D model requires further improvements, the results were nevertheless promising for the future use of this approach in braided rivers. Copyright © 2013 John Wiley & Sons, Ltd.  相似文献   

18.
Least action principle (LAP) in rivers is demonstrated by maximum flow efficiency (MFE) and is the foundation of variational mechanics based on energy and work rather than Newtonian force and momentum. Empirical evidence shows it to be the primary control for the adjustment of alluvial channels. Because most rivers flow with imposed water and sediment loads down valley gradients they have largely inherited, they self‐regulate energy expenditure to match the work they are required to do to remain stable. Overpowered systems develop a variety of channel patterns to expend excess energy and remain stable. Australia offers an opportunity to study low‐energy rivers closely adjusted to very low continental gradients. The anabranching Marshall and single‐thread Plenty Rivers flow down nearly straight channels with average H numbers [ratio between excess bed shear and width/depth (W/D) ratio] close to the optimum of 0.3 for stationary equilibrium. Ridge‐form divisions of the original channel width create anabranches that radically alter W/D ratios relative to bed shear, the same being true for short‐wide islands on the large low‐gradient Yangtze River in China. In contrast, Mount Chambers Creek in Australia's tectonically more active Flinders Ranges is accreting an alluvial fan with unstable distributary channels exhibiting H numbers well below the optimum. LAP also explains profound biases in Earth's stratigraphic record. Because meandering is an energy‐shedding mechanism, sinuous rivers sequester relatively little sediment resulting in all sequences being just a few tens of metres thick. In contrast, low‐energy braided disequilibrium systems can sequester sediment piles over a kilometre in thickness and tens of kilometres wide. LAP provides a new paradigm for river research by identifying the attractor state controlling river channel evolution. It links advances in theoretical physics to fluvial geomorphology, stratigraphy and hydraulic engineering and opens opportunities for diverse investigations in Earth system science. Copyright © 2016 John Wiley & Sons, Ltd.  相似文献   

19.
Landscape adjustment to tectonic, lithologic and climatic forcing leads to drainage reorganization and migration of divides. The respective contribution of these forcings, especially on carbonate landscapes is not well defined. Here, we have addressed this issue by combining field observations, satellite image interpretation and digital elevation model (DEM) quantitative analysis to assess drainage response to spatially heterogeneous rainfall, asymmetric uplift, and normal faulting on an emerging carbonated platform (Sumba Island, Indonesia). We map geomorphic markers of fluvial dynamics and drainage rearrangement and compute a χ parameter that incorporates the contributions of unevenly distributed precipitation and asymmetric uplift to estimate erosional disequilibrium across drainage divides. We find that asymmetric emergence of Sumba Island created an initial parallel drainage, asymmetric across a divide that propagates landwards. Soon after establishing itself on the emerging slopes this drainage was disturbed by normal faulting, which has become the main force driving drainage rearrangement. Vertical offsets across normal fault scarps first triggered aggradation within valleys over the hanging walls, and then disconnected upstream reaches from downstream reaches, leading to the formation of wind gaps atop the fault scarps and upstream perched sedimentary basins. The defeat of rivers by growing fault scarps was catalysed by the possibility for surface water to be rerouted near the fault scarps into underground water networks inside the underlying carbonates. At the end of the process, the opposite drainage across the main water divide captured the struggling drainage. Capture mechanisms include initial groundwater capture of the perched alluvial aquifers, followed by ground sapping at the head of the opposite drainage and surface stream diversion by avulsion. Finally, normal faulting is the main driving force of drainage rearrangement allowing avulsion and karstic rerouting whereas asymmetric uplift and climate forcings have shown a low efficiency. The role of karstification is more ambiguous, catalysing or inhibiting drainage rearrangement. Copyright © 2018 John Wiley & Sons, Ltd.  相似文献   

20.
During the evolution of meander bends, the intra‐meander groundwater head gradients steepen and generate zones of accelerated water and nutrient intra‐meander fluxes important for ecosystem processes. This paper compares and contrasts three MODFLOW groundwater model packages based on their simulation of intra‐meander flux for two stages of meander evolution observed in a sandbox river table and one level of river bed clogging, where the hydraulic conductivity in the river bed is lower than in the adjacent aquifer. These packages are the Time‐Variant Specified Head package [constant head (CHD)], River package (RIV), and Streamflow‐Routing package (SFR2), each controlling the groundwater or river head bounding the intra‐meander region. The RIV and SFR2 packages fix river stage and allow for variation in groundwater head below the river, which is suggested for simulating intra‐meander flux for all sinuosities with and without river bed clogging whenever river bed parameters are available. The CHD package fixes below river groundwater head and fails to simulate intra‐meander head loss and flux in meanders with high sinuosity or river bed clogging. In low sinuosity meanders and in cases without river bed clogging, there were no significant differences between MODFLOW packages for simulating river intra‐meander head loss and flux. This research demonstrates why MODFLOW users need to consider the limitations of each package when simulating intra‐meander flux in reaches with river bed clogging, high sinuosity, or similarly steep hydraulic gradients. Copyright © 2014 John Wiley & Sons, Ltd.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号