首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献，搜索用时 15 毫秒
1.
The planform dynamics of meandering rivers produce a complex array of meander forms, including elongated meander loops. Thus far, few studies have examined in detail the flow structure within meander loops and the relation of flow structure to patterns of planform change. This field‐based investigation examines relations between three‐dimensional fluid motion and channel change within an elongated, asymmetrical meander loop containing multiple pool–riffle structures. The downstream velocity field is characterized by a high‐velocity core that shifts slightly outward as flow moves through individual lobes of the loop. For some of the measured flows this core becomes submerged below the water surface downstream of the lobe apexes. Vectors of cross‐stream/vertical velocities indicate that skew‐induced helical motion develops within the pools near lobe apexes and decays over riffles where channel curvature is less pronounced. Maximum rates of bank retreat generally occur near lobe apexes where impingement of the flow on the outer channel bank is greatest. However, maximum rates and loci of bank retreat differ for upstream and downstream lobes of the loop, leading to increasing asymmetry of loop geometry over time—a finding consistent with experimental investigations of loop evolution. Copyright © 2003 John Wiley & Sons, Ltd.  相似文献   

2.
This paper analyses types and rates of change in river meander morphology and the links between mechanisms of change and emergent behaviour of planform morphology. It uses evidence of four dates of aerial photography combined with annual field mapping and ground photography to examine the morphological changes and mechanisms of change in a series of bends on an active meandering river, the River Dane in NW England, over a 25 year period. This unique data set allows insight into the spatial and temporal variability of bank line movement and component processes. Bank lines were mapped photogrametrically from air photos of 1984, 1996, 2001 and 2007 and the digitised courses compared in ArcGIS to produce calculations of erosional and depositional areas and rates. Most bends exhibit morphological change that largely follows the autogenic sequence, identified in qualitative models of meander development, from low sinuosity curves through simple symmetric and asymmetric bends to compound forms with lobe development in the apex region. Rates of erosion and bankline movement increase through this sequence until the compound phase. Relationships of amounts of movement to various curvature measures of bend morphology are complex. Several new loops, distinct from compound bend behaviour, have developed during the study period in formerly straight sections. Mechanisms of morphological change are illustrated for four types of bends: new, rapid growth bend; sharp‐angled bend with mid‐channel bar development; symmetric migrating bend; and simple to compound bend development. The changes take place in phases that are not simply related to discharge but to inherent sequences and feedbacks in development of bars and bend morphology and timescales for these are identified. Overall, emergent behaviour of systematic planform change, moderated by channel confinement and boundary features, is produced from spatially and temporally varied channel processes. Copyright © 2010 John Wiley & Sons, Ltd.  相似文献   

3.
Recent field and modeling investigations have examined the fluvial dynamics of confluent meander bends where a straight tributary channel enters a meandering river at the apex of a bend with a 90° junction angle. Past work on confluences with asymmetrical and symmetrical planforms has shown that the angle of tributary entry has a strong influence on mutual deflection of confluent flows and the spatial extent of confluence hydrodynamic and morphodynamic features. This paper examines three‐dimensional flow structure and bed morphology for incoming flows with high and low momentum‐flux ratios at two large, natural confluent meander bends that have different tributary entry angles. At the high‐angle (90°) confluent meander bend, mutual deflection of converging flows abruptly turns fluid from the lateral tributary into the downstream channel and flow in the main river is deflected away from the outer bank of the bend by a bar that extends downstream of the junction corner along the inner bank of the tributary. Two counter‐rotating helical cells inherited from upstream flow curvature flank the mixing interface, which overlies a central pool. A large influx of sediment to the confluence from a meander cutoff immediately upstream has produced substantial morphologic change during large, tributary‐dominant discharge events, resulting in displacement of the pool inward and substantial erosion of the point bar in the main channel. In contrast, flow deflection is less pronounced at the low‐angle (36°) confluent meander bend, where the converging flows are nearly parallel to one another upon entering the confluence. A large helical cell imparted from upstream flow curvature in the main river occupies most of the downstream channel for prevailing low momentum‐flux ratio conditions and a weak counter‐rotating cell forms during infrequent tributary‐dominant flow events. Bed morphology remains relatively stable and does not exhibit extensive scour that often occurs at confluences with concordant beds. Copyright © 2014 John Wiley & Sons, Ltd.  相似文献   

4.
We develop a new method for analysis of meandering channels based on planform sinuosity. This analysis objectively identifies three channel‐reach lengths based on sinuosity measured at those lengths: the length of typical, simple bends; the length of long, often compound bends; and the length of several bends in sequence that often evolve from compound bends to form multibend loops. These lengths, when normalized by channel width, tend to fall into distinct and clustered ranges for different natural channels. Mean sinuosity at these lengths also falls into distinct ranges. That range is largest for the third and greatest length, indicating that, for some streams, multibend loops are important for planform sinuosity, whereas for other streams, multibend loops are less important. The role of multibend loops is seldom addressed in the literature, and they are not well predicted by previous modelling efforts. Also neglected by previous modelling efforts is bank–flow interaction and its role in meander evolution. We introduce a simple river meandering model based on topographic steering that has more in common with cellular approaches to channel braiding and landscape evolution modelling than to rigorous, physics‐based analyses of river meandering. The model is sufficient to produce reasonable meandering channel evolution and predicts compound bend and multibend loop formation similar to that observed in nature, in both mechanism and importance for planform sinuosity. In the model, the tendency to form compound bends is sensitive to the relative magnitudes of two lengths governing meander evolution: (i) the distance between the bend cross‐over and the zone of maximum bank shear stress, and (ii) the bank shear stress dissipation length related to bank roughness. In our simple model, the two lengths are independent. This sensitivity implies that the tendency for natural channels to form compound bends may be greater when the banks are smoother. Copyright © 2002 John Wiley & Sons, Ltd.  相似文献   

5.
Tian Zhou  Ted Endreny 《水文研究》2012,26(22):3378-3392
River restoration projects have installed j‐hook deflectors along the outer bank of meander bends to reduce hydraulic erosion, and in this study we use a computational fluid dynamics (CFD) model to document how these deflectors initiate changes in meander hydrodynamics. We validated the CFD with streamwise and cross‐channel bankfull velocities from a 193° meander bend flume (inlet at 0°) with a fixed point bar and pool equilibrium bed but no j‐hooks, and then used the CFD to simulate changes to flow initiated by bank‐attached boulder j‐hooks (1st attached at 70°, then a 2nd at 160°). At bankfull and half bankfull flow the j‐hooks flattened transverse water surface slopes, formed backwater pools upstream of the boulders, and steepened longitudinal water slopes across the boulders and in the conveyance region off the mid‐channel boulder tip. Streamwise velocity and mass transport jets upstream of the j‐hooks were stilled, mid‐channel jets were initiated in the conveyance region, eddies with a cross‐channel axis formed below boulders, and eddies with a vertical axis were shed into wake zones downstream of the point bar and outer bank boulders. At half bankfull depth conveyance region flow cut toward the outer bank downstream of the j‐hook boulders and the secondary circulation cells were reshaped. At bankfull depth the j‐hook at 160° was needed to redirect bank‐impinging flow sent by the upstream j‐hook. The hooked boulder tip of both j‐hooks funneled surface flow into mid‐channel plunging jets, which reversed the secondary circulation cells and initiated 1 to 3 counter rotating cells through the entire meander. The main outer bank collision zone centered at 50° without the j‐hook was moved by the j‐hook to within and just beyond the 70° j‐hook boulder region, which displaced other mass transport zones downstream. J‐hooks re‐organized water surface slopes, streamwise and cross‐channel velocities, and mass transport patterns, to move shear stress from the outer bank and into the conveyance and mid‐channel zones at bankfull flow. At half bankfull flows a patch of high shear re‐attached to the outer bank below the downstream j‐hook. J‐hook geometry and placement within natural meanders can be analyzed with CFD models to help restoration teams reach design goals and understand hydraulic impacts. Copyright © 2011 John Wiley & Sons, Ltd.  相似文献   

6.
1 INTRODUCTION The plane shape of a river channel is very important for river improvement planning, because it must allow floodwater to flow off safely. Natural rivers wind from side to side, which creates meandering forms. From the history of river impro…  相似文献   

7.
Alternate bars have the property that they migrate downstream whenever floods occur. However, in meander channels whose bend angles are larger than a critical value, the migration of bars can be suppressed, and the positions of bank erosion and flood attack also will be steady. In this study, the bed morphology in flume channels with bends of various lengths and angles is investigated at various flow discharges, and the relation of bed morphology to surface flow is investigated in detail using fluid measuring software. An effort is made to obtain guidelines for the plane shape design of meander channels. Based on the experimental results of bed topography and measurement of surface flow direction and velocity distribution, from the viewpoint of bank erosion and the concentration and dispersion of flood flow the most suitable plane shape for meandering channels is suggested through which the migration of alternate bars is suppressed.  相似文献   

8.
A depth‐averaged linearized meander evolution model was calibrated and tested using the field data collected at the Quinn River in the Black Rock Desert, Nevada. Two approaches used to test the model were: (1) simulating meander evolution and comparing the results with the observed 38 year migration pattern; and (2) fitting the model parameters to present bank asymmetry (the ratio of the maximum bank gradients on opposite sides of the channel). The data required as input were collected in the field during a high flow in May 2011 and from aerial photographs and LiDAR data. Both approaches yielded similar results for the best fit parameter values. The bank asymmetry analysis showed that the bank asymmetry and the velocity perturbation have high correlation at close to zero spatial lag while the maximum correlation between the bank asymmetry and maximum bend curvature is offset by about 25 m. The model sufficiently replicated 38 years of channel migration, with a few locations significantly under‐ or over‐predicted. Inadequacies of the flow model and/or variation in bank properties unaccounted for are most likely the causes for these discrepancies. Flow through the Quinn River was also simulated by a more general 3D model. The downstream pattern of near‐bank shear stresses simulated by the 3D model is nearly identical to those resulting from the linearized flow model. Topographic profiles across interior bends are essentially invariant over a wide range of migration rates, suggesting that the traditional formulation that cut bank erosion processes govern migration rates is appropriate for the Quinn River. Copyright © 2014 John Wiley & Sons, Ltd.  相似文献   

9.
The effects of aquatic macrophytes on flow and turbulence were studied in a tightly curving meander bend. Three field measurement campaigns were carried out within a one year period to capture effects of seasonal changes in macrophyte cover. They comprised three‐dimensional velocity measurements and mappings of vegetation cover and bathymetry. Flow accelerates and converges over the run into an axial pool in a jet‐like flow pattern bordered by outer and inner bank flow separation zones. The jet and widening of the cross‐section anticipate helical flow until the second half of the bend, where an asymmetric pool developed. Submerged vegetation at the riffles preserves the jet at much lower discharges during the summer period by concentrating high momentum fluid near the surface. Plants locally modify the velocity and stress patterns, reduce bed shear stresses, create zones of fine sediment accumulation and reinforce the bed and banks with roots and rhizomes. Plant patches colonising the banks and the point bar confine secondary flow cells laterally and affect shape and magnitude of the transverse flow profiles near their edges. The morphology of the bend was very stable over the observation period and neither bank erosion nor pool scouring occurred. However, fine sediments accumulate within vegetation patches and in the recirculation zones while the remaining open areas tend to erode slightly. With the decay of macrophytes in winter, sediment accumulations are mobilised again and the bathymetry levels, supporting cyclic models of morphologic change in vegetated bends. In the second part of the paper, semi‐empirical models for the three predominant flow types were tested and discussed; velocity and stress models of vegetated mixing layers and plane turbulent jets, and Rozovskii's model for the transverse flow in bends. Copyright © 2012 John Wiley & Sons, Ltd.  相似文献   

10.
Two reaches of Aguapeí River, a left‐bank tributary of the Paraná River in western São Paulo state, Brazil, were studied with the objective of assessing the role of bend curvature on channel migration in this wet‐tropical system and examining if land‐use changes or ENSO (El Niño Southern Oscillation) driven climate anomalies over nearly half a century have changed migration behaviour and planform geometry. Meander‐bend migration rates and morphometric parameters including meander‐bend curvature, sinuosity, meander wavelength and channel width, were measured and the frequency of bend cutoffs was analysed in order to determine the rate of change of channel adjustment over a 48 year period to 2010. Results show that maximum average channel migration rates occur in bends with curvatures of about 2–3 rc/w, similar to other previously studied temperate and subarctic freely meandering rivers although not as pronounced and with a tendency to favour tighter curvature. From 1962 to 2010 the Aguapeí River has undergone a significant reduction in sinuosity, a shift from tightly curving to more open bends, an overall decline in channel migration rates, an associated decrease in the frequency of neck‐cutoffs and an overall increase in channel width. As the majority of the drainage basin (96%) was already deforested in 1962, channel form and process changes were, unlike an interpretation for an adjacent river system, not attributed to altered land‐use but rather to a sharp ENSO‐driven increase in the magnitude of peak flow‐discharges of some 32% since 1972. In summary, this research revealed that recent climate and associated flow regime changes are having a pronounced effect on river channel behaviour in the Aguapeí River investigated here. Copyright © 2018 John Wiley & Sons, Ltd.  相似文献   

11.
An in‐house fully three‐dimensional general‐purpose finite element model is applied to solve the hydrodynamic structure in a periodic Kinoshita‐generated meandering channel. The numerical model solves the incompressible Reynolds‐averaged Navier–Stokes equations for mass and momentum, while solving the k ? ε equations for turbulence. The free surface is described by the rigid‐lid approximation (using measured water surface data) for flat (smooth‐bed) and self‐formed (rough‐bed) conditions. The model results are compared against experimental measurements in the ‘Kinoshita channel’, where three‐dimensional flow velocities and turbulence parameters were measured. This validation was carried out for the upstream‐valley meander bend orientation under smooth (flat bed) conditions. After validation, several simulations were carried out to predict the hydrodynamics in conditions where either it was not possible to perform measurements (e.g. applicability of the laboratory acoustic instruments) and to extrapolate the model to other planform configurations. For the flat smooth‐bed case, a symmetric (no skewness) planform configuration was modeled and compared to the upstream‐skewed case. For the self‐formed rough‐bed case, prediction of the hydrodynamics during the progression of bedforms was performed. It appears that the presence of bedforms on a bend has the following effects: (i) the natural secondary flow of the bend is disrupted by the presence of the bedforms, thus depending on the location of the dune, secondary flows might differ completely from the traditional orientation; (ii) an increment on both the bed and bank shear stresses is induced, having as much as 50% more fluvial erosion, and thus a potential increment on the migration rate of the bend. Implications on sediment transport and bend morphodynamics are also discussed in the paper. Copyright © 2013 John Wiley & Sons, Ltd.  相似文献   

12.
Air photo interpretation and field survey were used to examine rates and patterns of planform change over the last 40 years on an 80 km reach of the Luangwa River, Zambia. The river, a tributary of the Zambezi, is a 100–200 m wide, medium sinuosity sand‐bed river (sinuosity index 1·84). High rates of channel migration (<33 m a−1) and cutoffs on meandering sections are frequent. Some meandering reaches, however, have remained relatively stable. A form of anastomosing with anabranches up to 14 km in length is also a characteristic. Patterns of meander development vary between bends but all can be described in relation to traditional geomorphic models; change occurs by translation, rotation, double‐heading, concave bank bench formation and cutoff causing river realignment. At the local scale spatial variability in bank resistance, induced by floodplain sedimentology, controls rate of bank erosion, and valley‐side channel ‘deflection’ is also apparent. Copyright © 2000 John Wiley & Sons, Ltd.  相似文献   

13.
The braided Jamuna River frequently changes its courses.Sometimes the secondary channel in a braided river acts as a single thread meandering channel.In the present study an attempt has been made to investigate the flow patterns and to estimate the rate of bank erosion in a bend along the Jamuna River.The three dimensional(3D) flow velocities were measured using Acoustic Doppler Current Profiler(ADCP).It is found that the near bank velocity is amplified by 1.1 to 1.3 times as compared with the section averaged velocity.A dominant secondary current is found in the upstream bend.The evolution as well as decay of the secondary current is not as clear as it is found in the laboratory experiments.It is revealed from the analysis of the flow process that the causes of higher rate of erosion at the study bend are the oblique flow near bankline,six times amplified shear velocity than critical shear velocity near bankline and the secondary current which acts as a sediment transporting agent from the outer bank towards the inner bank or the sand bar.Based on the flow processes,a simplified erosion prediction model is developed and applied to estimate the rate of erosion at a selected bend.Finally the predicted results have been compared with the observed data at the bend and all the available data at other bends along the Jamuna River.  相似文献   

14.
Meander bends of many large, sand‐bed meandering rivers are partitioned by chute channels that convey permanent flow, and co‐exist with the mainstem for decades. As a first step toward understanding the dynamics and morphodynamic implications of these ‘bifurcate meander bends’, this study applied binary logistic regression analysis to determine whether it is possible to predict chute initiation based on attributes of meander bend character and dynamics. Regression models developed for the Strickland River, Papua New Guinea, the lower Paraguay River, Paraguay/Argentina, and the Beni River, Bolivia, revealed that the probability of chute initiation at a meander bend is a function of the bend extension rate (the rate at which a bend elongates in a direction perpendicular to the valley axis trend). Image analyses of all rivers and field observations from the Strickland suggest that the majority of chute channels form during scroll–slough development. Rapid extension is shown to favour chute initiation by breaking the continuity of point bar deposition and vegetation encroachment at the inner bank, resulting in widely‐spaced scrolls with intervening sloughs that are positively aligned with primary over‐bar flow. The rivers plot in order of increasing chute activity on an empirical meandering‐braided pattern continuum defined by potential specific stream power (ωpv) and bedload calibre (D50). Increasing stream power is considered to result in higher bend extension rates, with implications for chute initiation. In addition, chute stability is shown to depend on river sediment load relative to flow discharge (Qs/Q), such that while the Beni may plot in the region of highly braided rivers by virtue of a high potential specific stream power, the formation of stable chute channels is suppressed by the high sediment load. This tendency is consistent with previous experimental studies, and results in a planform that is transitional between single‐thread meandering and braided. Copyright © 2011 John Wiley & Sons, Ltd.  相似文献   

15.
The effects of ice cover on flow characteristics in meandering rivers are still not completely understood. Here, we quantify the effects of ice cover on flow velocity, the vertical and spatial flow distribution, and helical flow structure. Comparison with open‐channel low flow conditions is performed. An acoustic doppler current profiler (ADCP) is used to measure flow from up to three meander bends, depending on the year, in a small sandy meandering subarctic river (Pulmanki River) during two consecutive ice‐covered winters (2014 and 2015). Under ice, flow velocities and discharges were predominantly slower than during the preceding autumn open‐channel conditions. Velocity distribution was almost opposite to theoretical expectations. Under ice, velocities reduced when entering deeper water downstream of the apex in each meander bend. When entering the next bend, velocities increased again together with the shallower depths. The surface velocities were predominantly greater than bottom/riverbed velocities during open‐channel flow. The situation was the opposite in ice‐covered conditions, and the maximum velocities occurred in the middle layers of the water columns. High‐velocity core (HVC) locations varied under ice between consecutive cross‐sections. Whereas in ice‐free conditions the HVC was located next to the inner bank at the upstream cross‐sections, the HVC moved towards the outer bank around the apex and again followed the thalweg in the downstream cross‐sections. Two stacked counter‐rotating helical flow cells occurred under ice around the apex of symmetric and asymmetric bends: next to the outer bank, top‐ and bottom‐layer flows were towards the opposite direction to the middle layer flow. In the following winter, no clear counter‐rotating helical flow cells occurred due to the shallower depths and frictional disturbance by the ice cover. Most probably the flow depth was a limiting factor for the ice‐covered helical flow circulation, similarly, the shallow depths hinder secondary flow in open‐channel conditions. Copyright © 2016 John Wiley & Sons, Ltd.  相似文献   

16.
Channel curvature produces secondary currents and a transverse sloping channel bed, along which the depth increases towards the outer bank. As a result deep pools tend to form adjacent to the outer bank, promoting bank collapse. The interaction of sediment grains with the primary and secondary flow and the transverse sloping bed also causes meanders to move different grain sizes in different proportions and directions, resulting in a consistent sorting pattern. Several models have been developed to describe this process, but they all have the potential to over‐predict pool depth because they cannot account for the influence of erodible banks. In reality, bank collapse might lead to the development of a wider, shallower cross‐section and any resulting flow depth discrepancy can bias associated predictions of flow, sediment transport, and grain‐size sorting. While bed topography, sediment transport and grain sorting in bends will partly be controlled by the sedimentary characteristics of the bank materials, the magnitude of this effect has not previously been explored. This paper reports the development of a model of flow, sediment transport, grain‐size sorting, and bed topography for river bends with erodible banks. The model is tested via intercomparison of predicted and observed bed topography in one low‐energy (5·3 W m?2 specific stream power) and one high‐energy (43·4 W m?2) study reach, namely the River South Esk in Scotland and Goodwin Creek in Mississippi, respectively. Model predictions of bed topography are found to be satisfactory, at least close to the apices of bends. Finally, the model is used in sensitivity analyses that provide insight into the influence of bank erodibility on equilibrium meander morphology and associated patterns of grain‐size sorting. The sensitivity of meander response to bank cohesion is found to increase as a function of the available stream power within the two study bends. Copyright © 2002 John Wiley & Sons, Ltd.  相似文献   

17.
Upland swamp channels with low width/depth ratios (w/d), armoured beds, minimal sediment loads, tightly curving bends and an absence of point bars provide a striking contrast to the flow characteristics of larger channels with higher w/d ratios. Two subsets of these bends were examined in relation to their patterns of cross‐stream flow relative to the channel boundary. The first, with mean w/d = 2·0 and gentle barforms, exhibited even velocity distributions at bend entrances but developed vertically stacked pairs of maximum velocity filaments (MVFs). Cross‐stream circulation increased with decreasing curvature before essentially ceasing in the tightest bend due to the conservation of angular momentum and reduced vertical velocity differentials; bed friction has more limited influence in narrow deep channels relative to bank friction. In the second subset of bends, with larger w/d (mean 4·8) and much steeper barforms, the MVFs were laterally paired and strongly helical flow was partly driven by the vertical confinement of flow due to large, stable barforms at the bend entrances. In one bend, the velocity profile became inverted immediately past the apex and caused helical flow to abruptly reverse. Point bars in relatively wide bedload channels appear to greatly distort secondary flow patterns. In narrow, deep, sediment‐starved channels, separation zones against the convex and/or the concave bank deliver the flow confinement that would otherwise be provided by point bars or concave‐bank benches. In these channels, separation zones are important for protecting both the channel bed and banks from scour. Three‐dimensional near bankfull flow fields are presented for one bend with a meander pool; inward shifting of the MVF and limited sediment supply are proposed as mechanisms for the development and maintenance of these features. These flow data in narrow and deep peatland channels demonstrate very different flow patterns and morphological characteristics relative to the more commonly studied wide, shallow channels with more abundant sediment. Copyright © 2009 John Wiley & Sons, Ltd.  相似文献   

18.
Hydraulic interactions between rivers and floodplains produce off‐channel chutes, the presence of which influences the routing of water and sediment and thus the planform evolution of meandering rivers. Detailed studies of the hydrologic exchanges between channels and floodplains are usually conducted in laboratory facilities, and studies documenting chute development are generally limited to qualitative observations. In this study, we use a reconstructed, gravel‐bedded, meandering river as a field laboratory for studying these mechanisms at a realistic scale. Using an integrated field and modeling approach, we quantified the flow exchanges between the river channel and its floodplain during an overbank flood, and identified locations where flow had the capacity to erode floodplain chutes. Hydraulic measurements and modeling indicated high rates of flow exchange between the channel and floodplain, with flow rapidly decelerating as water was decanted from the channel onto the floodplain due to the frictional drag provided by substrate and vegetation. Peak shear stresses were greatest downstream of the maxima in bend curvature, along the concave bank, where terrestrial LiDAR scans indicate initial floodplain chute formation. A second chute has developed across the convex bank of a meander bend, in a location where sediment accretion, point bar development and plant colonization have created divergent flow paths between the main channel and floodplain. In both cases, the off‐channel chutes are evolving slowly during infrequent floods due to the coarse nature of the floodplain, though rapid chute formation would be more likely in finer‐grained floodplains. The controls on chute formation at these locations include the flood magnitude, river curvature, floodplain gradient, erodibility of the floodplain sediment, and the flow resistance provided by riparian vegetation. Copyright © 2015 John Wiley & Sons, Ltd.  相似文献   

19.
The Geul River, located in the south‐eastern part of The Netherlands, is a meandering river with a planform shape characterized by large loops consisting of multiple bends. We evaluate the effect(s) of groundwater flow on the shapes of meanders as a possible explanation for the multi‐bend loops, using a combined meandering–groundwater computer model. In the model seeping groundwater enhances bank erodibility. Based on the simulation results, we present a conceptual, generalized model for groundwater–meandering interaction, based on wavelength selection and fixation effects. Wavelength selection occurs because of the positive feedback between growing meander bends and groundwater flow patterns and velocities. The promoted wavelengths have the same spatial scale as the groundwater flow system in the aquifer underlying the floodplain. In the case of the Geul River these wavelengths are of the order of 100 m. Since groundwater flow velocities are largest close to the recharging hill‐slopes, the seepage‐enhanced bank erodibilities are at a maximum near the floodplain limits. At these locations the difference in erodibility between banks facing the floodplain and those facing the hill slopes is large, so it is difficult for the river to migrate away from the floodplain limits. This causes long stretches of the river to be aligned along the floodplain limits, which we term a fixation effect. This mechanism best explains the multi‐bend loops of the Geul River. The general interaction between groundwater flow and meandering is site specific since it depends on climatic, fluvial and hydrogeological parameters. The Geul is characterized by a wide floodplain and steep hill‐slopes, and it is underlain by coarse‐grained deposits with good aquifer properties, favoring an important groundwater system. Since this kind of river frequently occurs, our results could apply to many other river systems. Copyright © 2008 John Wiley & Sons, Ltd.  相似文献   

20.
The interplay between streamwise flow,curvature-induced secondary flow,sediment transport and bed morphology leads to the formation of a typical bar-pool bed morphology in open-channel bends.The associated scour at the outer bank and deposition at the inner bank may endanger the outer bank’s stability or reduce the navigable width of the channel.Previous preliminary laboratory experiments in a sharply curved flume with a fixed horizontal bed have shown that a bubble screen located near the outer bank can generate an additional secondary flow located between the outer bank and the curvature-induced secondary flow and with a sense of rotation opposite to the latter.This bubble-induced secondary flow redistributes velocities and bed shear stresses.The reported study investigates the implications of a bubble screen on the flow and the morphology in configurations with mobile bed.Velocity measurements show that the bubble-induced secondary flow shifts the curvature-induced secondary flow in inwards direction and reduces its strength.The bubble screen considerably reduces morphological gradients.Maximum bend scour is reduced by about 50%and occurs further away from the outer bank where it does not endanger the bank stability anymore.The location of maximum scour coincides with the junction of the curvature-induced and bubble-induced secondary flows.At this same location,the maximum streamwise velocities and maximum vertical velocities impinging on the bed also occur,which indicates their importance with respect to the formation of bend scour.The bubble screen also substantially reduced deposition at the inner bank.These preliminary experiments show the potential of a bubble screen to influence and modify the bed morphology.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号