共查询到20条相似文献，搜索用时 15 毫秒
1.
Multi-phase simulations of turbulent driven flow in a dense medium cyclone with magnetite medium have been conducted in Fluent, using the Algebraic Slip Mixture model to model the dispersed phases and the air-core, and both the Large Eddy Simulation turbulence model (LES) and Reynolds Stress Models (RSM) for turbulence closure. The predicted air-core shape and diameter were found to be close to the experimental results measured by gamma ray tomography. It is possible to use the LES turbulence model with ASM multi-phase model to predict the air/slurry interface accurately. Multi-phase simulations (air/water/medium) show appropriate medium segregation effects but over-predict the level of segregation compared to that measured by gamma ray tomography near the wall. This is believed to be because of unaccounted back-mixing of the dispersed phase due to turbulence in the basic Algebraic Slip Mixture model. The predictions of accurate axial segregation of magnetite medium are investigated using the LES turbulence model in conjunction with the multi-phase mixture model and viscosity corrections according to the feed particle loading factor. At higher feed densities the agreement between the Dunglison [Dunglison, M.E., 1999, A general model of the dense medium cylone, PhD thesis, JKMRC, University of Queensland] correlations and experimental measurements and the CFD is reasonably good, but the overflow density is lower than the model predictions. It is believed that the excessive underflow volumetric flow rates are responsible for under prediction of the overflow density. The effect of size distribution of the magnetite has been fully studied. As expected, the ultra-fine magnetite sizes (i.e. 2 and 7 microns) are distributed uniformly throughout the cyclone. As the size of magnetite increases, more segregation of magnetite occurs close to the wall. 相似文献
2.
Mingze Liu Guang Zhang Guogang Gou Bing Bai Shaobin Hu Xiaochun Li 《Natural Hazards》2018,90(3):1137-1151
Reasonable determination of formation fracturing pressure concerns the stable operation of underground fluid injection projects. In this work, we studied the effect of unsteady flow on fracturing pressure. Hydraulic fracturing tests on low permeable sandstone were conducted with the injection rate between 0.1 and 2.0 ml/min. Then, the fracturing pressure prediction models for hollow cylinder under both unsteady flow and steady flow conditions were deduced. Finally, the effect of unsteady flow on the fracturing pressure was studied based on the experimental result and several influence factors. It was shown that fracturing pressure increased with the elevated pressurization rate in the tests, while the slope of the variation curve decreases. The model considering unsteady flow can reflect the variation tendency of fracturing pressures in experiments, while fracturing pressures from the model considering steady flow are invariant with different pressurization rates. Fracturing pressure decreases with the elevated rock permeability and increases with the elevated fluid viscosity, and these two effects are actually generated by the unsteady flow. Whether to consider the unsteady flow has no significant influence on the effect of rock tensile strength on fracturing pressure when the tensile strength is very low. However, when the tensile strength is high, the effect of unsteady flow cannot be neglected. 相似文献
3.
4.
The stratigraphic record and processes of turbidity current transformation across deep‐marine lobes 
下载免费PDF全文
下载免费PDF全文 Ian A. Kane Anna S. M. Pontén Brita Vangdal Joris T. Eggenhuisen David M. Hodgson Yvonne T. Spychala 《Sedimentology》2017,64(5):1236-1273
Sedimentary facies in the distal parts of deep‐marine lobes can diverge significantly from those predicted by classical turbidite models, and sedimentological processes in these environments are poorly understood. This gap may be bridged using outcrop studies and theoretical models. In the Skoorsteenberg Formation (South Africa), a downstream transition from thickly bedded turbidite sandstones to argillaceous, internally layered hybrid beds, is observed. The hybrid beds have a characteristic stratigraphic and spatial distribution, being associated with bed successions which generally coarsen and thicken‐upward reflecting deposition on the fringes of lobes in a dominantly progradational system. Using a detailed characterization of bed types, including grain size, grain‐fabric and mineralogical analyses, a process‐model for flow evolution is developed. This is explored using a numerical suspension capacity model for radially spreading and decelerating turbidity currents. The new model shows how decelerating sediment suspensions can reach a critical suspension capacity threshold beyond which grains are not supported by fluid turbulence. Sand and silt particles, settling together with flocculated clay, may form low yield strength cohesive flows; development of these higher concentration lower boundary layer flows inhibits transfer of turbulent kinetic energy into the upper parts of the flow ultimately resulting in catastrophic loss of turbulence and collapse of the upper part of the flow. Advection distances of the now transitional to laminar flow are relatively long (several kilometres) suggesting relatively slow dewatering (several hours) of the low yield strength flows. The catastrophic loss of turbulence accounts for the presence of such beds in other fine‐grained systems without invoking external controls or large‐scale flow partitioning and also explains the abrupt pinch‐out of all divisions of these sandstones. Estimation of the point of flow transformation is a useful tool in the prediction of heterogeneity distribution in subsurface systems. 相似文献
5.
6.
《地下水科学与工程》2019,(4)
The prediction of the probability of cavitation occurrence to prevent serious damages in the spillways is the major concern for hydraulic engineers. In this research,the three-dimensional model of Shahid Madani Dam's spillway was simulated with the Flow 3 D software and by the comparison of numerical model results with the experimental data, the probability of occurrence of the cavitation phenomenon has been investigated. The flow parameters including pressure, velocity, and water depth were calculated for three different flow rates of 495 m~3/s, 705 m~3/s and 2 205 m~3/s respectively.The Renormalization Group(RNG) turbulence model was used to simulate current turbulence. Comparison of simulation results for pressure, velocity and water depth with the results of the experimental model with two statistical indices Root Mean Square Error(RMSE) and Coefficient of Determination(R~2) showed that the numerical simulation results are in good consistency with experimental model. However, simulation results indicated that at any flow rates with a return period of 1 000 years, probable maximum flood and designed flow rates, the cavitation number is not lower than the critical cavitation number. Therefore, it is predicted that the cavitation phenomenon in Shahid Madani Dam's spillway will not happen. 相似文献
7.
旋转轴套在超深井工作时,其井下流动是三维湍流流动,旋转轴套的旋转和表面曲率效应以及随之而来的哥氏力和离心力,使流场在超深井的流动中极其复杂,同时,由于流体介质泥浆属于液固两相流,更致使内部流场测试困难,而且超深井中的工况在使用常规方法已很难得到较准确的数据。为此,将计算流体力学软件Fluent应用于超深井下流场的模拟,基于Navier-Stokes方程和Reynolds应力方程模型,建立多种仿真模型,在相同条件下,使用CFD仿真软件Fluent模拟仿真的不同结果,优化与旋转轴套叶片设计相关的几何参数,提高 相似文献
8.
The prediction of the probability of cavitation occurrence to prevent serious damages in the spillways is the major concern for hydraulic engineers. In this research, the three-dimensional model of Shahid Madani Dam’s spillway was simulated with the Flow 3D software and by the comparison of numerical model results with the experi-mental data, the probability of occurrence of the cavitation phenomenon has been investigated. The flow parameters including pressure, velocity, and water depth were calculated for three different flow rates of 495 m3/s, 705 m3/s and 2 205 m3/s respectively. The Renormalization Group (RNG) turbulence model was used to simulate current turbulence. Comparison of simulation results for pressure, velocity and water depth with the results of the experimental model with two statistical indices Root Mean Square Error (RMSE) and Coefficient of Determination (R2) showed that the numerical simulation results are in good consistency with experimental model. However, simulation results indicated that at any flow rates with a return period of 1 000 years, probable maximum flood and designed flow rates, the cavitation number is not lower than the critical cavitation number; Therefore, it is predicted that the cavitation phenomenon in Shahid Madani Dam’s spillway will not happen. 相似文献
9.
The role of shear dilation as a mechanism of enhancing fluid flow permeability in naturally fractured reservoirs was mainly recognized in the context of hot dry rock (HDR) geothermal reservoir stimulation. Simplified models based on shear slippage only were developed and their applications to evaluate HDR geothermal reservoir stimulation were reported. Research attention is recently focused to adjust this stimulation mechanism for naturally fractured oil and gas reservoirs which reserve vast resources worldwide. This paper develops the overall framework and basic formulations of this stimulation model for oil and gas reservoirs. Major computational modules include: natural fracture simulation, response analysis of stimulated fractures, average permeability estimation for the stimulated reservoir and prediction of an average flow direction. Natural fractures are simulated stochastically by implementing ‘fractal dimension’ concept. Natural fracture propagation and shear displacements are formulated by following computationally efficient approximate approaches interrelating in situ stresses, natural fracture parameters and stimulation pressure developed by fluid injection inside fractures. The average permeability of the stimulated reservoir is formulated as a function of discretized gridblock permeabilities by applying cubic law of fluid flow. The average reservoir elongation, or the flow direction, is expressed as a function of reservoir aspect ratio induced by directional permeability contributions. The natural fracture simulation module is verified by comparing its results with observed microseismic clouds in actual naturally fractured reservoirs. Permeability enhancement and reservoir growth are characterized with respect to stimulation pressure, in situ stresses and natural fracture density applying the model to two example reservoirs. Copyright © 2002 John Wiley & Sons, Ltd. 相似文献
10.
油井射流排砂泵扩散管出口流场分析 总被引：1，自引：0，他引：1
依据RNG-ε双方程湍流模型,建立油井射流排砂泵固液两相流方程;在此基础上,应用CFD计算机分析软件,对比分析了扩散管出口突变结构和渐变结构的射流排砂泵的效率、固相比、速度场分布、压力场分布。数值分析结果表明：射流泵扩散管出口采用渐变结构,可以有效减少固液两相流的逆向速度矢量,是提高射流排砂泵综合性能的有效手段。 相似文献
11.
12.
In this paper the powder snow avalanche is considered as a two-phase flow (air and snow particles). The equations governing this flow are the fluid mechanics conservation laws. The mass and the momentum conservation are considered for each phase. The interaction between the two phases takes into account the drag force between the particle and the air. Owing to high turbulence in the powder flow, a closure model was used based on a modified k - model in order to take into account the reduction of turbulence energy by the particles. The dense avalanche is modeled using the shallow water equations. The formation and the development of the powder avalanche is modeled using a mass and momentum exchanges between the powder flow and the dense flow. The flow area is digitized horizontally and vertically using a finite elements mesh. The numerical scheme is obtained by integrating the equations on each cell. The model thus built was calibrated using laboratory measurements of density current carried out in a flume. The model was successfully applied to reproduce many avalanches observed in France. At the end of this paper, an application of this model to an engineering case study is presented. It concerns the Uzengili path where an avalanche occurred in 1993. In this paper we use the integrated dense/powder avalanche model to define the effect of a powder avalanche flow in this path. Different simulations allow display of maps of the exposed zones for different available snow depths in the starting zone. The results were mapped in terms of dynamic pressure field and recommendations are proposed to the local authorities. 相似文献
13.
为研究不同流量比的两股射流入射水垫塘后的消能特性,选用非定常不可压缩流动的N-S方程和RNG k-ε紊流模型,采用VOF(Volume of Fluid)法结合溪洛渡双曲拱坝水垫塘进行了数值模拟,分析了流量比对水垫塘底板的冲击压力、临底速度、流态特征影响,并定量研究了流场内时均动能的衰减规律。研究表明,随着上游水股射流流量的减小,上游水股对底板的冲击压力在逐渐减小,由上游水股产生的动水垫作用逐渐减弱,使得下游水股对底板的冲击压力在逐渐增大;水垫塘流场呈现为具有动水垫效应的单股射流和动水垫效应微弱的单股射流两种形态。定量计算结果表明:对于上游水股射流,时均流速梯度较大,时均动能衰减较快,且随着上游水股射流流量减小,时均动能衰减速度加快,而下游水股射流的时均流能量比值和时均消能率总体小于上游水股射流消能率。 相似文献
14.
15.
16.
为使解析模型可以更加科学准确地描述储层中多相流体的迁移机制与压力演化规律,提高解析计算与分析的精度。首先将储层中的流场划分为3个区域,然后根据渗流体积守恒方程反演储层中两相流体混合渗流区的各相流体饱和度,进而将总流度直接引入到达西公式中得到了一个适用于两相流的广义达西公式,据此推导出了一个更为精确的表征储层流体压力演化规律的解析模型。最后,通过案例分析,将该解析模型的计算结果与既有文献的显式积分解及TOUGH2/ECO2N的数值解进行对比,验证了该模型的可靠性及相比于既有文献的显式积分解在计算精度方面的优越性。此外,计算结果也表明,该解析模型虽然是在稳态流的假定条件下得到的,但对于实际储层流体压力演化的全过程均具有很强的表征能力,这主要归因于该模型可科学准确地确定饱和度,因此,可以在工程中推广应用。 相似文献
17.
波流边界层水动力模拟对研究波流相互作用和泥沙运动具有重要的理论意义和实践价值。开发了波流边界层1DV垂向一维水动力数值模型,可用于模拟漩涡沙波床面和平底床面水动力特征。模型的构建基于边界层控制方程,平底床面采用k-ε模型,沙波床面采用双层模型,提出了漩涡层和紊动扩散层交界面紊动动能和紊动耗散率表达式。试验资料验证表明,模型较好地模拟了波浪-水流-床面共同作用下的边界层水动力特征,包括波周期内不同相位流速分布、紊动动能、剪切应力等以及波致时均流速分布和波流相互作用下的时均流速分布等。根据所建模型,讨论了不同床面和波流组合条件下的水动力特征。该模型可为研究波流边界层内水动力特征提供工具。 相似文献
18.
Comparing the performance of TRIGRS and TiVaSS in spatial and temporal prediction of rainfall-induced shallow landslides 总被引：1，自引：0，他引：1
This study compares the performance of transient rainfall infiltration and grid-based regional slope stability (TRIGRS) model and time-variant slope stability (TiVaSS) model in the prediction of rainfall-induced shallow landslides. TRIGRS employs one-dimensional (1-D) subsurface flow to simulate the infiltration rate, whereas a three-dimensional (3-D) model is utilized in TiVaSS. The former has been widely used in landslide modeling, while the latter was developed only recently. Both programs are used for the spatiotemporal prediction of shallow landslides caused by rainfall. This study uses the July 2011 landslide event that occurred in Mt. Umyeon, Seoul, Korea, for validation. The performance of the two programs is evaluated by comparison with data of the actual landslides in both location and timing by using a landslide ratio for each factor of safety class (\({\text{LR}}_{\text{class}}\) index), which was developed for addressing point-like landslide locations. Moreover, the influence of surface flow on landslide initiation is assessed. The results show that the shallow landslides predicted by the two models are highly consistent with those of the observed sliding sites, although the performance of TiVaSS is slightly better. Overland flow affects the buildup of the pressure head and reduces the slope stability, although this influence was not significant in this case. A slight increase in the predicted unstable area from 19.30 to 19.93% was recorded when the overland flow was considered. It is concluded that both models are suitable for application in the study area. However, although it is a well-established model requiring less input data and shorter run times, TRIGRS produces less accurate results. 相似文献
19.
Impact of single inclined faults on the fluid flow and heat transport: results from 3-D finite element simulations 总被引：1，自引：1，他引：0
Yvonne Cherubini Mauro Cacace Guido Blöcher Magdalena Scheck-Wenderoth 《Environmental Earth Sciences》2013,70(8):3603-3618
The impact of inclined faults on the hydrothermal field is assessed by adding simplified structural settings to synthetic models. This study is innovative in carrying out numerical simulations because it integrates the real 3-D nature of flow influenced by a fault in a porous medium, thereby providing a useful tool for complex geothermal modelling. The 3-D simulations for the coupled fluid flow and heat transport processes are based on the finite element method. In the model, one geological layer is dissected by a dipping fault. Sensitivity analyses are conducted to quantify the effects of the fault’s transmissivity on the fluid flow and thermal field. Different fault models are compared with a model where no fault is present to evaluate the effect of varying fault transmissivity. The results show that faults have a significant impact on the hydrothermal field. Varying either the fault zone width or the fault permeability will result in relevant differences in the pressure, velocity and temperature field. A linear relationship between fault zone width and fluid velocity is found, indicating that velocities increase with decreasing widths. The faults act as preferential pathways for advective heat transport in case of highly transmissive faults, whereas almost no fluid may be transported through poorly transmissive faults. 相似文献
20.
Michael R. Brady Demetri P. Telionis Pavlos P. Vlachos Roe-Hoan Yoon 《International Journal of Mineral Processing》2006,80(2-4):133-143
Industrial processes involving multi-phase flows such as flotation require understanding of the relationships between bubbles, solid particles and the flow. Modern experimental tools are employed in this effort to measure with great accuracy the basic features of the motion of all three phases in turbulent flow. We employed a unique Digital Particle Image Velocimeter (DPIV) that can record with great accuracy and kHz temporal resolution, velocity vectors of all three phases, namely the fluid, the solid particles and the air bubbles. The interaction of these three phases was studied in homogeneous isotropic turbulence generated by cylindrical grids. Particles and bubbles were released into the turbulence and the motions of the three phases were monitored. The experimental results obtained in the present work were compared with the predictions of the models published in the literature. 相似文献