共查询到20条相似文献，搜索用时 750 毫秒
1.
富钴结壳超细标准物质的加工制备 总被引：3，自引：2，他引：1
用气流磨制备了2个具有超细粒度的海山富钴结壳标准物质MCPt-1和MCPt-2。原样先经球磨成74μm(-200目),再用气流磨进行超细加工。样品粒度采用激光粒度仪检测,用粒度分布图和特征粒度来表达测量结果。两个样品的平均粒度分别为1.8μm和1.5μm(约2 000目),是目前粒度最小的标准物质。文章介绍了用于超细加工的流化床式气流磨原理与方法,展示了样品加工后的粒度分析结果,对比了国内外超细标准物质的概况。最后讨论了当前关注样品加工的重要性、超细加工的问题及超细样品分析研究的意义。 相似文献
2.
The fractal is presented as a method for describing the geometry of particles, with particular reference to the breakdown of granular soils and the formation of loess. The preliminary results are reported: (a) for the extent to which silt due to comminution exhibits a fractal distribution; (b) the tendency of fractal dimension to change with the comminution process; and (c) the relationship between fractal dimension describing particle size distribution and the grinding time. Laboratory simulation confirms the general tendency of fractal characteristics to reflect the size reduction process. 相似文献
3.
高压旋喷桩主要适用于淤泥质土、黏性土、粉土、砂土、黄土和碎石土等地层，在卵砾石地层或动水条件下的应用较少。我国某露天矿在施工旋喷桩止水帷幕的过程中，采用RJP工法进行帷幕施工，成功将高压旋喷注浆技术应用于卵砾石含水层中，通过试桩和筛分试验将卵砾石层特征对桩径大小的影响进行了分析研究，结果表明，RJP工法在卵砾石含水层中成桩效果良好、质量可靠，其桩径大小与卵砾石颗粒大小及含砂量有关。围井试验结果显示，高压旋喷桩帷幕墙完整，止水效果显著。研究成果表明高压旋喷注浆技术可在卵砾石含水层的加固和止水领域进行推广应用。 相似文献
4.
M. Vučnić Vasić J. Kiurski S. Aksentijević U. Kozmidis-Luburić 《International Journal of Environmental Science and Technology》2013,10(5):923-930
Concentrations of heavy metals, pH, and particle size distribution parameters were measured in Dragica stream and Djetinja River water receiving wastewaters from copper rolling mill industry, Sevojno. The concentrations of copper, zinc, lead, and mercury were determined for water samples collected in summer 2009. It was found that Copper Rolling Mill Sevojno was the significant source of water pollution with copper and zinc. Considering that copper rolling mill industry, one of the larger emitters of sulfur dioxide, pollutes the area, the water pH was surprisingly alkaline. The particle size analysis results showed that particles from oil-in-water emulsion evidently got into stream water in spite of the purification devices used. In order to assess the possible relations between the measured parameters, a correlation analysis was performed. The correlation analysis showed a significant positive correlation between the total metal concentrations of copper and zinc, as well as between particle size distribution parameters and the concentration of lead and copper. 相似文献
5.
The application of high-pressure roll mills (HPRM) for industrial comminution has been growing, particularly because of its energy efficiency. Many aspects of HPRM comminution have not been fully characterized because the performance of the machine is affected by numerous parameters that still need to be investigated and optimized. The present paper is concerned with the effect of feed moisture on HPRM performance. The comminution of minus 8-mesh dolomite feed at several different moisture levels was conducted with a laboratory HPRM to delineate the effect of feed moisture on product characteristics, specific energy consumption, and such mill operating parameters as applied load, roll gap and roll speed. The results showed definite effects of moisture on these parameters and the product size distribution, most likely because of lubrication of the particles in the compacting bed as they pass through the roll gap. 相似文献
6.
M. Sri Raj Rajeswari K.A.M. Azizli S.F.S. Hashim M.K. Abdullah M. Abdul Mujeebu M.Z. Abdullah 《International Journal of Mineral Processing》2011,98(1-2):94-105
This paper presents a three dimensional Computational Fluid Dynamics (CFD) model to investigate the flow dynamics of solid–gas phases during fine grinding in an air jet mill. Alpine 100AFG fluidized bed air jet mill is considered for the study and the jet milling model is simulated using FLUENT 6.3.2 using a standard k-ε model. The model is developed in GAMBIT 2.3.16 and meshed by tet/hybrid (T-Grid) and Triangular (Pave) meshes. The effects of operating parameters such as solid feed rate, grinding air pressure and internal classifier speed on the performance of the jet mill are analyzed. The CFD simulation results are presented in the forms of dual phase vector plot, volume fraction of phases and particle trajectories during fine grinding process. The mass of ground feed entering and leaving the cyclone (underflow) is also computed by simulation. The proposed model gives realistic predictions of the flow dynamics within the jet mill. Experiments are conducted on the Alpine 100AFG jet mill to study the particle size, morphology and mass of the ground product. The numerical results are found in good agreement with the experimental results. 相似文献
7.
高压水射流的破岩效果对高压水射流辅助掘进机破岩技术至关重要。为提升隧道掘进机工况下高压水射流辅助破岩的效率,开展大线速度下超高压水射流破岩试验,分析喷嘴移动线速度、射流压力和喷嘴直径对破岩效果的影响规律,并探究加磨料和射流形式对破岩效果的影响。试验结果表明,随喷嘴移动线速度增加,高压水射流的切割深度和切割宽度均近似线性减小;随射流压力增加,切割深度近似线性增大,压力从200 MPa提高到280 MPa,切割深度增加了72%～82%;喷嘴直径从0.35 mm增大到0.60 mm,切割深度增加了60%～85%。大线速度下加磨料后射流变发散,加磨料的切割深度小于纯水的切割深度,加磨料的切割宽度大于纯水的切割宽度。砂管束流射流模式的能量利用率更高,砂管束流的切割深度比长线射流的切割深度大35%～42%,砂管束流的切割宽度比长线射流的切割宽度大78%～85%。基于Crow切割岩石理论,通过试验数据回归分析,得到大线速度下超高压水射流切割深度半理论半经验预测模型,可为高压水射流辅助掘进机破岩技术中射流切割参数优化提供参考依据。研究成果对提升隧道掘进机工况下超高压水射流辅助破岩的效率是很有意义的。 相似文献
8.
A centrifugal mill is a high-power intensity media mill that can be used for ultra-fine grinding, employing centrifugal forces generated by gyration of the axis of the mill tube in a circle. The mill charge motion is quite different depending on the ratio of the gyration diameter to the mill diameter (G / D ratio), varying from a motion similar to that of a conventional tumbling media mill to that of a vibration mill. In this study, a centrifugal mill was constructed with an arrangement where the gyration diameter could be readily adjusted. The batch grinding characteristics of three different minerals (limestone, talc and illite) in water with dispersing agent were investigated at various G / D ratios. It was found that the optimum G / D ratio in terms of the specific energy consumption to give a desired fineness of product was different for the three minerals. This was due to their different reactions to the breakage mechanisms provided by the mill charge motion at varying G / D ratios. The size distributions became progressively narrower at increased grinding times, and particles finer than about 0.1 μm were not detected even for prolonged grinding times. Measurement of specific surface areas indicated that this was not due to an artifact of the size measurements by laser diffractometry. This implies that there is a limitation in which particles finer than 0.1 μm are not produced under the conditions tested in this type of mill, but further investigation is needed for experimental verification of this limit of comminution. 相似文献
9.
Ball milling is an energy-intensive unit operation and usually consumes a major proportion of the power drawn by a typical mineral processing plant. Hence, substantial economic benefits can be achieved by optimal design and by operating ball milling circuits under optimum process conditions. This requires an accurate ball mill modelling technique.In the multi-segment ball mill model, the size-dependent material transport within the mill varies systematically with the amount of coarse particles present in each segment. The ore-specific breakage distribution function can be determined from single particle breakage tests conducted using a computer-monitored twin pendulum apparatus. When the ore-specific breakage distribution function is used in the multi-segment, a constant relationship between the breakage rate parameters and mill diameter is observed. Thus, the performance of an industrial ball mill can be adequately described using the ore-specific breakage distribution function together with the systematic variation of the material transport and the breakage rate functions with process conditions and mill diameter, respectively.This ball mill modelling technique is illustrated using a case study on the design of a ball milling circuit for a particular grinding requirement and another case study on modelling the performance of an industrial ball milling circuit. 相似文献
10.
Liner design and lifter geometry in tumbling mills are very important in comminution kinetics and energy consumption. In terms of the parameters of the batch grinding model, the breakage rate function decreases as lifter size increases while the breakage distribution function is independent of the lifter size. However, the specific energy consumption is not a function of lifter size. Reducing the lifter height from 2.54 cm to 0.32 cm increases the production from this mill by 37%. When the mill is operated without any lifters, the charge apparently slips inside the shell resulting in lower breakage kinetics and higher energy consumption. 相似文献
11.
Grain-size distribution of subglacial till and its realtion to glacial scrushing and abrasion 总被引：1，自引：0，他引：1
SYLVI HALDORSEN 《Boreas: An International Journal of Quaternary Research》1981,10(1):91-105
A subglacial till formed from a sandstone bedrock has a variable grain-size distribution which reflects its variable genesis. Glacial comminution processes were simulated by artificial mill experiments with fragments of the sandstone bedrock. Pure crushing caused disintegration along mineral boundaries into separate minerals, most mineral grains retaining their primary size during the crushing process. Abrasion produced cracks across the minerals and resulted in silt-sized rock flour. The experiments indicate that most of the sand-sized till material formed as a result of crushing, while the silt is mainly the result of abrasion. The sand and silt are both regarded as components resistant to further glacial comminution, but are formed by different comminution processes. By considering also the coarser till material, the general principles of glacial breakdown of resistant rocks from boulders to sand or silt can be illustrated. A matrix index and an abrasion index based on the mill experiments distinguish well between genetically different subglacial till types 相似文献
12.
13.
14.
为定量获得土壤结构对其水力性质的指示作用,室内实验选用华北平原子牙河流域原状土样为研究对象,用张力计法和激光粒度分析仪分别测定土壤水分特征曲线和样品粒度分布,基于分形理论计算土壤粒度分布的分形维数,采用实验测定与模型验证相结合的方法对水分特征曲线进行分析.结果表明,土壤颗粒粒度分布在[10 μm,50 μm]区间内的分段分维值是表征土壤粒度累积分布显著上升段特征的关键参数,与0~80 kPa吸力范围内的土壤水分特征曲线幂函数模型拟合参数(a、b)有极显著相关关系.研究区内土壤水分特征曲线以分形形式表达的幂函数模型为:θ=100.78×(3-D)S(D-3)/3,利用土壤结构分形特征能够有效指示其水力性质. 相似文献
15.
A fundamental yet still unresolved puzzle provided by cataclasis is whether particle size reduction mostly progresses through time by the same fragmentation mechanism or not. Available field, laboratory and numerical modelling results on the evolution of cataclastic rocks are still controversial. The evidence that cataclastic rocks exert a primary control on the frictional strength, stability, seismic velocity and permeability properties of fault zones encourages further research on cataclasis. Here, we report data on particle shape from natural cataclastic rocks in poorly layered carbonates in the Apulian foreland of the Southern Apennines of Italy. Particle shape analyses show that particle angularity decreases with increasing size and, for a given size class, it decreases with increasing fractal dimension of the particle size distribution. These results offer support to the temporally and spatially variable nature of rock comminution. 相似文献
16.
Experimental and modeling investigation of sewage solids sedimentation based on particle size distribution and fractal dimension 总被引：5，自引：4，他引：1
J. Wu Ph.D. C. He Ph.D. 《International Journal of Environmental Science and Technology》2010,7(1):37-46
Sewage solids are usually characterized by non-specific parameters such as suspended solids. The suspended solids has been shown to be an inadequate index for advanced water treatment processes. In this study, the sewages solids particle size distribution was used to provide more detailed information on sewage characteristic. It is hoped that, by introducing particle size distribution, the mechanism of sewage solids sedimentations can be better understood. The particle size distribution of the domestic sewage was measured by the Malvern® laser scattering technique to link to its settlement efficiency. Experimental results show that 77 % of particle volume was removed during the 90 min settling, of which 71.2 % of particle volume was removed in the initial 30 min. The submicron particles were found to be removed by co-settling with large particles. The fractal dimensions of sewage solids could also be derived from the laser scattering measurement. The fractal dimension could also provide useful information on the shape and density of sewage solids. A mathematical model considering the particle sizes, shapes and density changes was then constructed to simulate the settlement of raw sewage particles. Comparison of the modeling results based on discrete and flocculant settling theory shows that settlement can be better predicted by considering the fractal nature of particles. The particle size distribution and fractal dimension data measured by Malvern® laser scattering technique have been shown to be valuable data for in-depth understanding of the mechanisms of sewage solids sedimentation. 相似文献
17.
基于多重分形理论的多年冻土区高寒草甸退化过程中土壤粒径分析 总被引：5，自引：0，他引：5
为阐明青藏高原多年冻土区高寒草甸退化过程中土壤粒径分布(PSD)非均匀性和异质性的变化特征, 在青藏高原长江源区, 根据高寒草甸的退化梯度, 选取了未退化区域、 轻度退化区域、 中度退化区域、 重度退化区域和极重度退化区域, 测定了高寒草甸退化过程中土壤的粒径分布、 饱和导水率、 孔隙度与有机质含量. 运用多重分形理论, 并结合土壤颗粒分布与土壤理化特性等参数的相关性进行分析, 为高寒草甸退化对长江源高寒土壤性质变化的影响的定量研究提供一种精确的分析方法. 结果表明: 随着青藏高原多年冻土区高寒草甸退化程度的增加, 土壤颗粒呈粗粒化趋势, 多重分形参数中容量维数(D0)随之增大, 表征PSD宽度随之增大; 信息维数(D1)、 信息维数/容量维数(D1/D0)、 关联维数(D2)、 奇异谱宽(Δα)可从不同角度反映的土壤PSD的非均匀性与局部异质性随着高寒草甸退化有先增大后减小的趋势, 中度退化区域的土壤PSD不均匀性最大. 研究发现, 研究区土壤多重分形参数与细砂含量、 土壤的孔隙度、 有机质含量具有较明显的相关性. 多重分形参数能准确描述高寒草甸退化过程中土壤粒径分布的细微差别, 可作为反映土壤性质的潜在指标. 相似文献
18.
19.
Water retention of clayey soils with wide particle size distributions involves a combination of capillary and adsorbed layers effects that result into suction–saturation relations spanning over multiple decades of matric suction values. The present study provides a physics-based analysis to reproduce the water retention curve of such soils based solely on particle size distribution and porosity. The distribution of inter-particle pore sizes is inferred through a probabilistic treatment of the particle size distribution, which is then used, together with an assigned pore entry pressure, to estimate the inter-particle water volume at a given suction. The contribution to water content from adsorbed layers is also taken into account by considering the balance of electrochemical forces between water and clay material. The total water content is therefore found by summing up the contribution of inter-particle water, as well as adsorbed layers that form around clay particles and around the individual clay platelets. Comparisons with experimental results on nine different soil samples verify the capability of the model in accurately predicting the wide water retention curves without any prior calibration. Additional to capturing the essential features of the water retention curve with remarkable detail, the analytical model also provides insights into the relative contributions of capillary and adsorbed waters to the overall saturation at different suction regimes. Being based upon easily accessible information such as particle size distribution and void ratio, the model can therefore be considered as a substitute for costly and lengthy laboratory and in situ measurements of water retention curve.
相似文献20.
Samayamutthirian Palaniandy Khairun Azizi Mohd AzizliHashim Hussin Syed Fuad Saiyid Hashim 《International Journal of Mineral Processing》2007
Silica was ground in an oscillating mill at various grinding period to study the mechanochemical effect in fine grinding process. The ground particles exhibited massive size reduction where the volume moment diameter of 5.56 μm was reached within 600 s. Aggregation of fine particles was very pronounced when it was ground for 600 s due to high surface energy. Aggregation of fine particles caused the ground particles to exhibit poly-modal particle size distribution. Line broadening and reduction of diffractogram peak intensity were observed. Amorphization rate up to 16.9% was exhibited by the particle ground for 600 s. Preferential breakage of plane was observed where (101) and (111) was easily distorted compared to (110) and (200). Rapid reduction of crystallite size was observed at early stage of grinding until it reached a plateau at 5 nm at 600 s whilst the change in lattice strain was 0.5%. 相似文献