共查询到17条相似文献，搜索用时 653 毫秒
1.
2.
建立设备-结构耦合隔震体系模型,选取近断层脉冲型和非脉冲型地震波各50条,计算耦合隔震体系的动力响应。分析表明,近断层脉冲型地震动对耦合隔震体系的影响大于非脉冲型地震动,且对主体结构的影响大于对设备的影响;近断层脉冲型地震作用下的隔震层位移、层间位移、楼层加速度、设备加速度和设备位移的平均响应分别达到非脉冲型地震作用的2.25倍、2.17倍、2.24倍、1.17倍和1.20倍。进行设备-结构耦合隔震体系设计时,需考虑近断层地震动脉冲作用的影响,同时需注意引起主体结构和设备最大响应的地震动不一定相同。 相似文献
3.
选择台湾集集地震和美国北岭地震的近断层地震动记录作为输入,考察了近断层地震动破裂向前方向性与滑冲效应引起的两种不同速度脉冲运动对单自由度体系和长周期橡胶支座隔震建筑结构抗震性能的影响.反应谱分析表明,破裂向前方向性与滑冲效应对工程结构地震响应的影响是随结构周期变化的.在中短周期段,含破裂向前方向性效应地震动的谱加速度值大于含滑冲效应地震动的谱加速度值;而在长周期段,含滑冲效应地震动的谱加速度大于含破裂向前方向性效应的谱加速度值.并且,与无脉冲地震动作用相比,含破裂向前方向性与滑冲效应脉冲的近断层地震动作用下隔震建筑的地震响应显著增大.滑冲效应引起的速度脉冲使隔震建筑底部的层间变形和楼层剪力明显增大,这意味着滑冲效应脉冲比向前方向性效应脉冲对长周期建筑结构的破坏更具危害性. 相似文献
4.
近断层地震动中长周期、短持时和高能量的加速度脉冲将对高层摩擦摆基础隔震结构的减震性能产生不利影响,考虑土-结构相互作用（SSI效应）后的隔震结构将产生动力耦合效应,可能进一步放大隔震结构地震响应。为此,通过一幢框架-核心筒高层摩擦摆基础隔震结构的非线性地震响应分析,考察近断层脉冲型地震动作用下框架-核心筒摩擦摆基础隔震结构的层间位移角、楼层加速度和隔震层变形等响应规律,揭示隔震体系的损伤机理。基于集总参数SR （sway-rocking）模型,分析不同场地类别与不同地震动类型对隔震体系动力响应影响规律。结果表明:高层摩擦摆基础隔震结构在近断层脉冲型地震动作用下的减震效果相比普通地震动减震效果变差,楼层剪力、层间位移角和隔震层变形等超越普通地震动作用下的1.5倍;对于Ⅲ和Ⅳ类场地类别,考虑SSI效应使隔震结构的地震响应进一步放大,弹塑性层间位移角随着土质变软增大尤为明显。 相似文献
5.
针对巨-子结构隔震体系,在隔震层处或子结构顶部与主结构连接处,施加SMA-压电智能复合阻尼器,从而形成巨-子结构智能隔震体系。本文通过限界Hrovat最优控制算法设计了巨-子结构智能隔震体系的半主动控制器,在此基础上,对巨-子结构智能隔震体系进行了Simulink控制效果仿真分析,同时比较了控制装置安装位置的不同对结构控制效果的影响,并与普通隔震结构的减震效果进行了对比。研究结果表明,智能隔震控制1（隔震层加控制装置）和智能隔震控制2（子结构顶部加控制装置）2种控制方案在控制结构的位移方面效果相差不大。总体而言,智能隔震控制2对于控制子结构单元顶部的绝对加速度效果更为显著,但是相对于普通隔震而言,特别是在控制隔震层位移方面2种方案都具有较好的控制效果。实施智能控制可以有效改善巨-子结构被动控制体系的抗震性能,并能降低隔震结构在遭受强震时由于隔震层出现过大位移导致结构倾覆的危险。 相似文献
6.
近场地震动具有很高的加速度峰值和长周期的速度脉冲,因此能够对结构造成严重的破坏.基础隔震是一种有效的减震技术,然而这种单一的减震手段在低频具有很高能量的近场脉冲型地震动作用下已不能确保结构的安全,必须寻求新的减震策略.本文将速度脉冲模型与随机地震地面运动模型联合来生成近场脉冲型地震动,并以此作为激励,用MATLAB对近场脉冲型地震动作用下TMD-基础隔震混合控制结构及独立基础隔震结构的地震响应进行求解,比较研究该混合控制结构的减震效果.结果表明该混合控制方式可以有效地控制结构的位移,而对加速度的控制效果不明显. 相似文献
7.
通过对隔震结构进行非线性动力响应分析,分别研究地震动参数和支座参数对结构地震响应的影响。首先,建立铅芯橡胶支座基础隔震结构的非线性运动方程;然后,以人工合成脉冲型地震动作为输入,运用MATLAB进行编程并求解结构在脉冲型地震动作用下的地震响应;最后,分别研究速度脉冲周期、支座屈服力、屈服后与屈服前的刚度比对隔震支座最大位移和上部结构层间位移的影响。研究结果表明,脉冲周期对结构地震响应影响很大,在进行隔震设计时应使结构自振周期远离脉冲周期;支座刚度比对结构地震响应影响较大,在进行支座选型时应重点关注;支座屈服力对支座位移的影响显著,屈服力越大,支座位移越小。 相似文献
8.
9.
近断层地震动脉冲特性在2个水平分量上具有差异,采用平方和开方法分析了近断层脉冲地震动双向地震作用下基础隔震结构和组合隔震结构的隔震层位移,并与近断层脉冲单向地震作用进行了对比分析,结果表明:若仅地震动加速度峰值大的分量或2个方向分量均存在明显速度脉冲,则产生的隔震层位移大于单向地震动;若仅地震动加速度峰值小的分量存在明... 相似文献
10.
隔震结构具有较长自振周期,且容易受地震动长周期特性的影响,因此其在长周期地震动作用下的抗震性能值得研究。以某基于规范设计的基础隔震结构为例,通过对该结构在规范规定地震作用和远场长周期地震作用下的地震响应进行分析和对比,研究长周期地震动对结构地震响应的影响;通过对钢筋和混凝土的损伤状态进行定义和标识,探讨长周期地震作用下基础隔震结构的损伤分布规律。研究结果表明,长周期地震动作用下隔震结构发生破坏的概率远大于具有相同峰值地面加速度的普通地震动,其中长周期地震动反应谱的谱峰值"后移"被认为是造成这种情况的主要原因,且长周期地震动作用下隔震结构的损伤分布并不均匀,其主要集中在结构的底层。 相似文献
11.
近断层速度脉冲型地震动研究对揭示建筑结构的破坏机理、开展抗震设防以及抗震设计具有重要价值。首先,对速度脉冲成因进行了系统的总结,并探讨了区分方向性效应速度脉冲和滑冲效应速度脉冲的思路;其次,系统地介绍了近断层速度脉冲的识别方法,评述了各种脉冲识别方法的优缺点;然后,基于速度脉冲特性,探讨了前方向性效应对速度脉冲特性的影响以及速度脉冲对反应谱的放大作用;最后,对速度脉冲型地震动输入方法以及对结构响应研究进行了系统总结,探讨了速度脉冲型地震动输入的关键问题。基于丰富的理论研究,未来对于速度脉冲型地震动研究工作应当充分结合实际工程需求,推进理论成果的规范标准化与工程实践。 相似文献
12.
The rocking response of large flexible structures to earthquakes 总被引：1，自引：0，他引：1
The rocking response of structures subjected to strong ground motions is a problem of ‘several scales’. While small structures are sensitive to acceleration pulses acting successively, large structures are more significantly affected by coherent low frequency components of ground motion. As a result, the rocking response of large structures is more stable and orderly, allowing effective isolation from the ground without imminent danger of overturning. This paper aims to characterize and predict the maximum rocking response of large and flexible structures to earthquakes using an idealized structural model. To achieve this, the maximum rocking demand caused by different earthquake records was evaluated using several ground motion intensity measures. Pulse-type records which typically have high peak ground velocity and lower frequency content caused large rocking amplitudes, whereas non-pulse type records caused random rocking motion confined to small rocking amplitudes. Coherent velocity pulses were therefore identified as the primary cause of significant rocking motion. Using a suite of pulse-type ground motions, it was observed that idealized wavelets fitted to velocity pulses can adequately describe the rocking response of large structures. Further, a parametric analysis demonstrates that pulse shape parameters affect the maximum rocking response significantly. Based on these two findings, a probabilistic analysis method is proposed for estimating the maximum rocking demand to pulse-type earthquakes. The dimensionless demand maps, produced using these methods, have predictive power in the near-field provided that pulse period and amplitude can be estimated a priori. Use of this method within a probabilistic seismic demand analysis framework is briefly discussed. 相似文献
13.
14.
This study focuses on the response of seismic isolated bridges subjected to near-field ground motions with distinct pulse type behavior in terms of maximum isolator displacements (MIDs) and maximum isolator forces (MIFs) transferred to the substructure. The employed isolation systems are composed of lead rubber bearings (LRBs) with bi-linear force-deformation relations that consider cycle-to-cycle deterioration in the yield strength of the LRBs due to heating of the lead core. MIDs and MIFs with due consideration of cycle-to-cycle deterioration are compared with that of non-deteriorating ones. Bounding analyses are also performed for comparison purposes. Nonlinear response history analyses are conducted with two bins of ground motions recorded at different soil conditions to investigate the effect of ground motion characteristics. Results indicate that MIDs are overestimated by lower bound analyses when seismic isolated bridges are subjected to near-field motions with high velocity pulses especially for the bearings with higher Q/W ratios. 相似文献
15.
根据台湾西部地质地貌特征和1999年集集MW7.6地震的研究成果,建立三维速度结构模型和震源模型,并采用三维有限差分法对双冬断层可能产生的近断层脉冲型地震动进行数值模拟。结果表明,方向性效应引起的双向速度脉冲集中在垂直于断层滑动分量的方向上,而滑冲效应引起的单向速度脉冲则集中在平行于断层滑动分量的方向上。受方向性效应和上盘效应的共同调制,近断层脉冲型地震动反映出不对称带状分布的特征,速度脉冲主要分布在距离断层面约10 km的范围内。凹凸体的特性影响着地震动的时空分布,由地震波场显示南投和台中处于强地震动危险区。近场脉冲型地震动的研究对分析速度脉冲形成机理以及地震危险性有一定的参考意义。 相似文献
16.
A series of relatively long-period velocity pulses appearing in the later part of ground motion, which is the characterization of far-source long-period ground motions in basin (“long-period ground motion” for short), is mainly influenced by focal mechanism, basin effect, and dispersion. It was supposed that the successive low-frequency velocity pulses in long-period ground motion caused the resonance of long-period structures in basin, which are of special concern to designers of super high-rise buildings. The authors proposed a wavelet-based successive frequency-dependent pulse extraction (WSFPE) method to identify and extract these pulses with dominant period of interest from long-period ground motions. The pulses extracted by using two frequently used methods (zero-crossing analysis, empirical mode decomposition) were compared to the pulses extracted by using WSFPE. The results demonstrate that the WSFPE provides higher resolution in time–frequency domain than the other two methods do. The velocity pulses extracted by using WSFPE are responsible for the resonance and maximum response of structure subjected to long-period ground motions. WSFPE can be used to make a better understanding of long-period ground motions and to promote the formation of long-period ground motion model which will help the seismic design of long-period structures built in sedimentary basin. 相似文献
17.
Evaluation of a passive gap damper to control displacements in a shaking test of a seismically isolated three‐story frame 
下载免费PDF全文
下载免费PDF全文 Recent studies have indicated uncertainty about the performance limit states of seismically isolated buildings in very large earthquakes, especially if the isolator displacement demands exceed the seismic gap and induce pounding. Previous research has shown the benefit of providing phased supplemental damping that does not affect the isolation system response in a design event. A phased passive control device, or gap damper, was designed, fabricated, and experimentally evaluated during shake table testing of a quarter scale base‐isolated three‐story steel frame building. Identical input motions were applied to system configurations without a gap damper and with a gap damper, to directly assess the influence of the gap damper on displacement and acceleration demands. The gap damper was observed to reduce displacement demands by up to 15% relative to the isolated system without the gap damper. Superstructure floor accelerations increased substantially because of damper activation, but were limited to a peak of about 1.18 g. The gap damper reduces displacement most effectively if the ground motion contains one or more of the following characteristics: the spectral displacement increases with increasing period near the effective period of the isolation system, the motion is dominated by a single large pulse rather than multiple cycles at a consistent intensity, and the motion has a dominant component aligned with a major axis of the structure. Copyright © 2016 John Wiley & Sons, Ltd. 相似文献