共查询到18条相似文献，搜索用时 184 毫秒
1.
箱式超大型浮体结构在规则波中的水弹性响应研究 总被引：3，自引：5，他引：3
利用三维线性水弹性理论研究了箱式超大型浮体结构在正弦规则波中的动力响应，用Bernoulli-Euler梁解析解计算结构在真空中的动力特性，用弹性体三维势流理论计算结构的水动力系数，浮体结构在单位波幅规则波中的刚体运动幅值与DNV／WADAM程序的计算结果进行了比较，并给出了垂向弯曲模态的位移，弯矩随波浪频率的变化规律，由于箱式浮体结构的低阶固有频率很低，相应的弹性振型的响应与刚体运动耦合，结构在波浪中没有发现明显的低阶弹性模态谐振。 相似文献
2.
为了分析带支腿浮式结构水下桩腿处于不同的长度时振动固有频率的变化情况,采用有限元方法和三维线性水弹性理论对一理想的带支腿浮式结构进行研究,分工况计算了3种弹性模态的干、湿固有频率。结果表明对于同一阶弹性模态来说,结构主体平台振型是决定水动力系数大小的主要因素,桩腿水下长度是次要因素,而振型又受到桩腿长度的制约;桩腿水下长度的改变对带支腿浮式结构的干模态固有频率以及湿固有频率都有较明显地调制作用。对于干模态固有频率来说,桩腿关于船身越趋于对称分布时结构的共振频率越高;对于湿固有频率来说,水下桩腿长度地增加有迫使共振频率趋向低频方向移动趋势。 相似文献
3.
4.
研究计入弹性变形铰接塔平台在深水中的非线性动力响应。将铰接塔平台简化为顶部具有集中质量,底部具有扭转线性弹簧约束的均匀弹性梁,考虑波浪对平台的作用,应用莫里森(Morison)公式计算铰接塔平台瞬时位置所受水动力,建立了铰接塔平台横向运动的偏微分方程,采用伽辽金方法计算波浪作用下铰接塔平台非线性动力响应。计算了铰接塔平台的固有频率和模态,得到了铰接塔平台不同频率波浪激励下各阶模态的动力响应。计算结果表明,在波浪激励下系统二阶模态将发生2、34、倍超谐共振运动,并且揭示了弹性铰接塔平台在波浪作用下振动的不对称性。 相似文献
5.
在频域和时域内研究对等分布式系泊和分组式系泊2种系泊模式对Spar平台运动性能的影响,并分析单根系泊缆破断失效后平台运动性能的变化。首先建立Spar平台的三维水动力模型,通过在平台柱体导缆孔处指定预张力、倾角和刚度来模拟系泊系统的影响;然后采用三维势流理论进行浮体水动力计算,获得Spar平台运动响应的传递函数等水动力参数;最后根据实际海况资料,在平台生存工况下,进行Spar平台在完好系泊和单根系泊缆破断失效状态下运动响应的短期预报,并在时域内进行耦合分析,研究平台运动响应和系泊缆张力变化情况。研究结果对Spar平台系泊系统设计和平台设计前期运动性能研究有参考意义。 相似文献
6.
7.
漂浮式风电平台在波浪中的摇晃运动会导致塔架根部产生很大的弯矩,极大地威胁平台结构安全。同时流体的附连水质量效应对平台塔架结构的动响应有着较为显著的影响,因此充分考虑这种流固耦合效应有利于更加准确地评估平台塔架的结构动响应。采用三维频域线性水弹性方法计算塔架在流体作用下的结构共振频率特征以及各阶模态振动的主坐标响应特性,然后通过弹性模态叠加法获得塔架的弯矩载荷。并结合概率学手段,预报了短期极限海况下塔架弯曲载荷响应,为新一代漂浮式风电平台结构安全性评估和方案设计提供了技术支撑。 相似文献
8.
随着张力腿平台(TLP)在深海油气开发领域的广泛应用,在早期传统式(C-TLP)的基础上衍生出了多种结构形式,其中还有延展式(E-TLP)、最小化深海水面式(MOSES)和海之星式(SeaStar)已具备业界建造运营经验。为了体现TLP各类结构形式的性能特点,服务于工程开发方案中平台构型选择,本文基于三维势流理论频域方法,针对现已建造的4种TLP的水动力性能及相关参数进行了对比研究。首先,在质量惯性、结构刚度相似的条件下,完成了各类型平台的主尺度方案;其次,采用SESAM软件分析计算了各方案设计平台的附加质量、势流阻尼和运动响应幅值算子(RAO);最后的结果对比表明,不同结构形式对张力腿平台的固有周期影响很大,分散立柱形式的C-TLP与E-TLP的垂向运动响应更小。 相似文献
9.
10.
在工程设计中,通常采用模块化方式制造超大型浮式结构物,将巨大的单体结构分割成多个较小模块,后期通过合适的连接器拼装形成。为了明确多模块超大浮体在波浪作用下的水弹性响应,以两个相邻层合浮体（高刚度面板和低密度芯材）为研究对象,建立波浪作用下铰接层合浮体水弹性响应的高阶势流模型。采用匹配特征函数展开法求解流体运动的速度势,探讨了铰接处弹簧刚度对浮体的反射系数、透射系数、挠度、弯矩和剪力的影响规律。研究结果表明：迎浪侧浮体的存在可以有效降低背浪侧浮体的挠度、弯矩和剪力幅值;与垂直弹簧相比,扭转弹簧刚度的增加可以更加有效抑制铰接层合浮体的水弹性响应;当扭转弹簧刚度大于一定值时,继续增大弹簧刚度对浮体的动力响应不产生影响。 相似文献
11.
The application of very large floating structure (VLFS) to the utilization of ocean space and exploitation of ocean resources has become one of the issues of great interest in international ocean engineering field. Owing to the advantage of simplicity in structure and low cost of construction and maintenance, box-type VLFS can be used in the calm water area near the coast as the structure configuration of floating airport. In this paper, a 3D linear hydroelastic theory is used to study the dynamic response of box-type VLFS in sinusoidal regular waves. A beam model and a 3D FEM model are respectively employed to describe the dynamic characteristics of the box-type structure in vacuum. A hydrodynamic model (3D potential theory of flexible body) is applied to investigate the effect of different dry models on the hydroelastic response of box-type structure. Based on the calculation of hydroelastic response in regular waves, the rigid body motion displacement, flexible deflection, and the short term and long 相似文献
12.
In this paper,the effects of a quay or a solid jetty on hydrodynamic coefficients and vertical wave excitation forces on a ship woth or without forward speed are discussed.A modified simple Green function technique is used to calculate the 2D coefficients while the strip theory is used to calculate the 3D coefficients. Wave excitation forces are also calculated with the strip theory. Numerical results are provided for hydrodynamic coefficients and vertical wave excitation forces on a 200000 DWT tanker ship. It is found that the quay has a considerable effect on the hydrodynamic coefficients and wave excitation forces for a ship. 相似文献
13.
The Multiple Column Platform (MCP) semi-submersible is a newly proposed concept, which differs from the conventional semi-submersibles, featuring centre column and middle pontoon. It is paramount to ensure its structural reliability and safe operation at sea, and a rigorous investigation is conducted to examine the hydrodynamic and structural performance for the novel structure concept. In this paper, the numerical and experimental studies on the hydrodynamic performance of MCP are performed. Numerical simulations are conducted in both the frequency and time domains based on 3D potential theory. The numerical models are validated by experimental measurements obtained from extensive sets of model tests under both regular wave and irregular wave conditions. Moreover, a comparative study on MCP and two conventional semi-submersibles are carried out using numerical simulation. Specifically, the hydrodynamic characteristics, including hydrodynamic coefficients, natural periods and motion response amplitude operators (RAOs), mooring line tension are fully examined. The present study proves the feasibility of the novel MCP and demonstrates the potential possibility of optimization in the future study. 相似文献
14.
The deployment of suitable configurations of mutually interacting floating bodies for efficiently controlling their hydrodynamic interactions towards the reduction of the wave drift forces and, thus, of the mooring lines’ loads, has, nowadays, gained a great scientific interest. In this paper, the hydrodynamic behaviour of a floating cylinder and a concentric annular flexible plate is analysed in the frequency domain aiming at the minimization of the drift forces acting on the cylinder by optimizing the flexural rigidity of the plate. The diffraction/radiation problem is solved using a higher-order boundary element method. The analysis is implemented assuming that both floating bodies oscillate freely in heave, while for the plate, flexible modes are, additionally, considered for describing its structural deformations. The required modes shapes are determined in vacuum (“dry” mode superposition approach) through analytical expressions. The flexural rigidity of the plate, D, is optimized at a specific wave number using a real-coded genetic algorithm. Initially, results are compared with numerical results of other investigators for the case of two rigid concentric floating cylinders. Next, extended results are presented, focusing on the effect of D, including its optimum value, on various physical quantities describing the behaviour of both the cylinder and the plate. Contrary to the isolated cylinder, the presence of the plate introduces sharp peaks in the variation pattern of the drift force of the cylinder, bounded at specific wave numbers, where resonance of the seiche mode of water motion in the annular cavity or of specific flexible modes of the plate occurs. However, by reducing D to its optimum value, the cylinder’s drift force obtains practically zero values at the target wave number, due to an efficient improvement of the wave field in the annular cavity around the cylinder. Moreover, a great reduction of the drift force compared to the isolated cylinder is achieved in the subsequent high frequency range. 相似文献
15.
An approximate method is presented to estimate the hydrodynamic loading and structural response of an idealized offshore platform subjected to a regular train of linear surface waves. The platform is taken to consist of four bottom-mounted, flexible, circular cylinders supporting a rigid deck and is assumed to be aligned parallel to the incident wave direction. The response of each column is assumed to be one-dimensional and to be governed by linear beam theory. The solution technique for the fluid velocity potential involves replacing scattered waves by equivalent plane waves together with non-planar, first-correction terms, and can be shown to be a large spacing approximation.Numerical results are presented which show the effect of hydrodynamic interference and structural flexibility on the platform response. 相似文献
16.
Ioanna Diamantoulaki Demos C. Angelides George D. Manolis 《Applied Ocean Research》2008,30(4):243-255
The overall performance of pile-restrained flexible floating breakwaters is investigated under the action of linear monochromatic incident waves in the frequency domain. The aforementioned floating breakwaters undergo only vertical structural deflections along their length and are held in place by means of vertical piles. The total number of degrees of freedom equals the six conventional body modes, when the breakwater moves as a rigid body, plus the extra bending modes. These bending modes are introduced to represent the structural deflections of the floating breakwater and are described by the Bernoulli–Euler flexible beam equation. The number of bending modes introduced is determined through an appropriate iterative procedure. The hydrostatic coefficients corresponding to the bending modes are also derived. The numerical analysis of the flexible floating breakwaters is based on a three-dimensional hydrodynamic formulation of the floating body. A parametric study is carried out for a wide range of structural stiffness parameters and wave headings, to investigate their effect on the performance of flexible floating breakwaters. Moreover, this performance is compared with that of the corresponding pile-restrained rigid floating breakwater. Results indicated that the degree of structural stiffness and the wave heading strongly affect the performance of flexible floating breakwaters. The existence of an “optimum” value of structural stiffness is demonstrated for the entire wave frequency range. 相似文献
17.
Hydrodynamic interactions between two ships advancing in waves 总被引：3，自引：0，他引：3
In this paper the hydrodynamic problems between two moving ships in waves are analyzed using a three-dimensional potential-flow theory based on the source distribution technique. The potential is presented by a distribution of source over the ship hull. The corresponding Green functions and their derivatives can be easily solved numerically by using the series expansions of Telste and Noblesse's algorithm for the Cauchy principal value integral of unsteady flow. The numerical solution is evaluated by applying the present method to two pairs of models and compared with experimental data and strip theory. From the comparisons, it shows that the hydrodynamic interactions are generally important. In the resonance region, the hydrodynamic interaction calculated by the 3D method is more reasonable, which is not so significant as that by the 2D method. The technique developed here may serve as a more rigorous tool to analyze the related problems of two ships doing underway replenishment in waves. 相似文献
18.
C.Z. Wang 《Ocean Engineering》2010,37(4):400-417
Fully nonlinear interactions between water waves and vertical cylinder arrays in a numerical tank are studied based on a finite element method (FEM). The three-dimensional (3D) mesh is constructed through an extension of a 2D Delaunay surface grid along the vertical line. The velocity potential is obtained by solving a linear matrix system of FEM, and a difference scheme is then used to calculate the velocity on the free surface to track its movement. Waves and hydrodynamic forces are obtained for both bottom mounted and truncated cylinders. The simulations have provided many results to show the nature of mutual interference between cylinders in arrays and its effects on waves and forces at the nearly trapped mode frequency. The effect of the tank wall on waves and forces has been investigated, and the nonlinear features of waves and forces have also been discussed. 相似文献