首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献，搜索用时 31 毫秒
1.
  相似文献   

2.
One‐dimensional flow simulations were conducted at four locations of the shallow alluvial aquifer of the upper Rhine River (at the Erstein polder) to quantify the time‐dependent moisture distribution, the water flux and the water volume infiltrated in the unsaturated zone as a function of soil heterogeneities during a five‐day‐long flooding event. Three methods of estimating the hydraulic parameters of soil in the vadose zone were tested. They are based on the following: (1) experimental data, (2) soil particle‐size distribution and (3) pedology information on soils. Water fluxes calculated from modelling approaches 2 and 3 were compared with those of the experiment‐based values and the effect of these differences on the arrival time and velocity of water at the water table were analysed. Major differences in water fluxes were found among the methods of estimating the hydrodynamic parameters. At the Terrace location, the groundwater recharge predicted using soil data from methods 1 and 2 are approximately 4500 and 2400 mm, respectively. Flow simulations using soil data and the experiment‐based method show the highest velocities of infiltrating water at the soil surface and largest volume of groundwater infiltration but result in the lowest centres of the moisture content mass. The results obtained using soil data based on the pedological method are similar to those calculated using soil parameters based on the particle‐size distribution of extracted soil samples. Water pressure profiles calculated on Terrace and Channel location, 3 and 7 days after the inundation event agreed reasonably well with those observed when using hydrodynamic parameters from the experiment‐based method. However, the flow model using the pedology‐based parameters largely underestimates the time needed to achieve hydrostatic conditions of the soil water profile once water flooding at the soil surface stops. This can be mainly attributed to the low values of estimated van Genuchten parameter α. Copyright © 2012 John Wiley & Sons, Ltd.  相似文献   

3.
S. Nishat  Y. Guo  B. W. Baetz 《水文研究》2010,24(17):2417-2424
Soil moisture conditions prior to input design storms need to be known in the planning and design of urban stormwater control facilities using the design storm approach. Limited information is available on these soil moisture conditions which are commonly referred to as the antecedent soil moisture conditions. In this study, a deterministic continuous simulation model was used to simulate antecedent soil moisture conditions under south‐western Ontario, Canada, climate conditions. A wide range of different soil types were investigated and various statistical analyses on the simulated antecedent soil moisture results were performed. Frequency analyses illustrated typical distributions of antecedent soil moisture conditions and the influence of finer and coarser textured soil particles. Empirical equations were developed for the estimation of average antecedent soil moisture conditions based on commonly known soil characteristics. Satisfactory performance of the empirical equations was demonstrated by comparing between field average antecedent soil moisture data and empirically estimated average antecedent soil moisture values. These equations are therefore recommended for use in urban stormwater studies incorporating the design storm approach. Copyright © 2010 John Wiley & Sons, Ltd.  相似文献   

4.
Rapidly depleting unconfined aquifers are the primary source of water for irrigation on the North China Plain. Yet, despite its critical importance, groundwater recharge to the Plain remains an enigma. We introduce a one‐dimensional soil‐water‐balance model to estimate precipitation‐ and irrigation‐generated areal recharge from commonly available crop and soil characteristics and climate data. To limit input data needs and to simplify calculations, the model assumes that water flows vertically downward under a unit gradient; infiltration and evapotranspiration are separate, sequential processes; evapotranspiration is allocated to evaporation and transpiration as a function of leaf‐area index and is limited by soil‐moisture content; and evaporation and transpiration are distributed through the soil profile as exponential functions of soil and root depth, respectively. For calibration, model‐calculated water contents of 11 soil‐depth intervals from 0 to 200 cm were compared with measured water contents of loam soil at four sites in Luancheng County, Hebei Province, over 3 years (1998–2001). Each 50‐m2 site was identically cropped with winter wheat and summer maize, but received a different irrigation treatment. Average root mean‐squared error between measured and model‐calculated water content of the top 180 cm was 4·2 cm, or 9·3% of average total water content. In addition, model‐calculated evapotranspiration compared well with that measured by a large‐scale lysimeter. To test the model, 12 additional sites were simulated successfully. Model results demonstrate that drainage from the soil profile is not a constant fraction of precipitation and irrigation inputs, but rather the fraction increases as the inputs increase. Because this drainage recharges the underlying aquifer, improving irrigation efficiency by reducing seepage will not reverse water‐table declines. Copyright © 2003 John Wiley & Sons, Ltd.  相似文献   

5.
A comparison between half‐hourly and daily measured and computed evapotranspiration (ET) using three models of different complexity, namely, the Priestley–Taylor (P‐T), the reference Penman–Monteith (P‐M) and the Common Land Model (CLM), was conducted using three AmeriFlux sites under different land cover and climate conditions (i.e. arid grassland, temperate forest and subhumid cropland). Using the reference P‐M model with a semiempirical soil moisture function to adjust for water‐limiting conditions yielded ET estimates in reasonable agreement with the observations [root mean square error (RMSE) of 64–87 W m?2 for half‐hourly and RMSE of 0.5–1.9 mm day?1 for daily] and similar to the complex Common Land Model (RMSE of 60–94 W m?2 for half‐hourly and RMSE of 0.4–2.1 mm day?1 for daily) at the grassland and cropland sites. However, the semiempirical soil moisture function was not applicable particularly for the P‐T model at the forest site, suggesting that adjustments to key model variables may be required when applied to diverse land covers. On the other hand, under certain land cover/environmental conditions, the use of microwave‐derived soil moisture information was found to be a reliable metric of regional moisture conditions to adjust simple ET models for water‐limited cases. Further studies are needed to evaluate the utility of the simplified methods for different landscapes. Copyright © 2011 John Wiley & Sons, Ltd.  相似文献   

6.
We used the new process‐based, tracer‐aided ecohydrological model EcH2O‐iso to assess the effects of vegetation cover on water balance partitioning and associated flux ages under temperate deciduous beech forest (F) and grassland (G) at an intensively monitored site in Northern Germany. Unique, multicriteria calibration, based on measured components of energy balance, hydrological function and biomass accumulation, resulted in good simulations reproducing measured soil surface temperatures, soil water content, transpiration, and biomass production. Model results showed the forest “used” more water than the grassland; of 620 mm average annual precipitation, losses were higher through interception (29% under F, 16% for G) and combined soil evaporation and transpiration (59% F, 47% G). Consequently, groundwater (GW) recharge was enhanced under grassland at 37% (~225 mm) of precipitation compared with 12% (~73 mm) for forest. The model tracked the ages of water in different storage compartments and associated fluxes. In shallow soil horizons, the average ages of soil water fluxes and evaporation were similar in both plots (~1.5 months), though transpiration and GW recharge were older under forest (~6 months compared with ~3 months for transpiration, and ~12 months compared with ~10 months for GW). Flux tracking using measured chloride data as a conservative tracer provided independent support for the modelling results, though highlighted effects of uncertainties in forest partitioning of evaporation and transpiration. By tracking storage—flux—age interactions under different land covers, EcH2O‐iso could quantify the effects of vegetation on water partitioning and age distributions. Given the likelihood of drier, warmer summers, such models can help assess the implications of land use for water resource availability to inform debates over building landscape resilience to climate change. Better conceptualization of soil water mixing processes and improved calibration data on leaf area index and root distribution appear obvious respective modelling and data needs for improved simulations.  相似文献   

7.
This paper presents a top–down approach for soil moisture and sap flux sampling design with the goal of understanding ecohydrologic response to interannual climate variation in the rain–snow transition watersheds. The design is based on a priori estimates of soil moisture and transpiration patterns using a physical distributed model, Regional Hydro‐Ecologic Simulation System (RHESSys). RHESSys was initially calibrated with existing snow depth and streamflow data. Calibrated model estimates of seasonal trajectories of snowmelt, root‐zone soil moisture storage, and transpiration were used to develop five hydrologic similarity indicators and map these at (30 m) patch scale across the study watershed. The partitioning around medoids‐clustering algorithm was then used to define six distinctive spatially explicit clusters based on the five hydrologic similarity indictors. A representative site within each cluster was identified for sampling. For each site, soil moisture sensors were installed at the 30‐ and 90‐cm depths and at the five soil pits and a sap flux sensor at the averaged‐size white fir tree for each site. The model‐based cluster analysis suggests that the elevation gradient and topographically driven flow drainage patterns are the dominant drivers of spatial patterns of soil moisture and transpiration. The comparison of model‐based calculated hydrological similarity indicators with measured‐data‐based values shows that spatial patterns of field‐sampled soil moisture data typically fell within uncertainty bounds of model‐based estimates for each cluster. There were however several notable exceptions. The model failed to capture the soil moisture and sap flux dynamics in a riparian zone site and in a site where lateral subsurface flow may not follow surface topography. Results highlight the utility of using a hypothesis driven sampling strategy, based on a physically based model, for efficiently providing new information that can drive both future measurements and strategic refinements to model inputs, parameters, or structure that might reduce these errors. Future research will focus on strategies for using of finer scale representations of microclimate, topography, vegetation, and soil properties to improve models.  相似文献   

8.
  相似文献   

9.
Cosmic‐ray soil moisture sensors have the advantage of a large measurement footprint (approximately 700 m in diameter) and are able to operate continuously to provide area‐averaged near‐surface (top 10–20 cm) volumetric soil moisture content at the field scale. This paper presents the application of this technique at four sites in southern England over almost 3 years. Results show the soil moisture response to contrasting climatic conditions during 2011–2014 and are the first such field‐scale measurements made in the UK. These four sites are prototype stations for a UK COsmic‐ray Soil Moisture Observing System, and particular consideration is given to sensor operating conditions in the UK. Comparison of these soil water content observations with the Joint UK Land Environment Simulator 10‐cm soil moisture layer shows that these data can be used to test and diagnose model performance and indicate the potential for assimilation of these data into hydro‐meteorological models. The application of these large‐area soil water content measurements to evaluate remotely sensed soil moisture products is also demonstrated. Numerous applications and the future development of a national COsmic‐ray Soil Moisture Observing System network are discussed. Copyright © 2016 John Wiley & Sons, Ltd.  相似文献   

10.
The application of stationary parameters in conceptual hydrological models, even under changing boundary conditions, is a common yet unproven practice. This study investigates the impact of non‐stationary model parameters on model performance for different flow indices and time scales. Therefore, a Self‐Organizing Map based optimization approach, which links non‐stationary model parameters with climate indices, is presented and tested on seven meso‐scale catchments in northern Germany. The algorithm automatically groups sub‐periods with similar climate characteristics and allocates them to similar model parameter sets. The climate indices used for the classification of sub‐periods are based on (a) yearly means and (b) a moving average over the previous 61 days. Classification b supports the estimation of continuous non‐stationary parameters. The results show that (i) non‐stationary model parameters can improve the performance of hydrological models with an acceptable growth in parameter uncertainty; (ii) some model parameters are highly correlated to some climate indices; (iii) the model performance improves more for monthly means than yearly means; and (iv) in general low to medium flows improve more than high flows. It was further shown how the gained knowledge can be used to identify insufficiencies in the model structure. Copyright © 2015 John Wiley & Sons, Ltd.  相似文献   

11.
This article investigates the soil moisture dynamics within two catchments (Stanley and Krui) in the Goulburn River in NSW during a 3‐year period (2005–2007) using the HYDRUS‐1D soil water model. Sensitivity analyses indicated that soil type, and leaf area index were the key parameters affecting model performance. The model was satisfactorily calibrated on the Stanley microcatchment sites with a single point rainfall record from this microcatchment for both surface 30 cm and full‐profile soil moisture measurements. Good correlations were obtained between observed and simulated soil water storage when calibrations for one site were applied to the other sites. We extended the predictions of soil moisture to a larger spatial scale using the calibrated soil and vegetation parameters to the sites in the Krui catchment where soil moisture measurement sites were up to 30 km distant from Stanley. Similarly good results show that it is possible to use a calibrated soil moisture model with measurements at a single site to extrapolate the soil moisture to other sites for a catchment with an area of up to 1000 km2 given similar soils and vegetation and local rainfall data. Site predictions were effectively improved by our simple data assimilation method using only a few sample data collected from the site. This article demonstrates the potential usefulness of continuous time, point‐scale soil moisture data (typical of that measured by permanently installed TDR probes) and simulations for predicting the soil wetness status over a catchment of significant size (up to 1000 km2). Copyright © 2012 John Wiley & Sons, Ltd.  相似文献   

12.
Soil moisture is an important driver of growth in boreal Alaska, but estimating soil hydraulic parameters can be challenging in this data-sparse region. Parameter estimation is further complicated in regions with rapidly warming climate, where there is a need to minimize model error dependence on interannual climate variations. To better identify soil hydraulic parameters and quantify energy and water balance and soil moisture dynamics, we applied the physically based, one-dimensional ecohydrological Simultaneous Heat and Water (SHAW) model, loosely coupled with the Geophysical Institute of Permafrost Laboratory (GIPL) model, to an upland deciduous forest stand in interior Alaska over a 13-year period. Using a Generalized Likelihood Uncertainty Estimation parameterisation, SHAW reproduced interannual and vertical spatial variability of soil moisture during a five-year validation period quite well, with root mean squared error (RMSE) of volumetric water content at 0.5 m as low as 0.020 cm3/cm3. Many parameter sets reproduced reasonable soil moisture dynamics, suggesting considerable equifinality. Model performance generally declined in the eight-year validation period, indicating some overfitting and demonstrating the importance of interannual variability in model evaluation. We compared the performance of parameter sets selected based on traditional performance measures such as the RMSE that minimize error in soil moisture simulation, with one that is designed to minimize the dependence of model error on interannual climate variability using a new diagnostic approach we call CSMP, which stands for Climate Sensitivity of Model Performance. Use of the CSMP approach moderately decreases traditional model performance but may be more suitable for climate change applications, for which it is important that model error is independent from climate variability. These findings illustrate (1) that the SHAW model, coupled with GIPL, can adequately simulate soil moisture dynamics in this boreal deciduous region, (2) the importance of interannual variability in model parameterisation, and (3) a novel objective function for parameter selection to improve applicability in non-stationary climates.  相似文献   

13.
Evaporation rate estimation is important for water resource studies. Previous studies have shown that the radiation‐based models, mass transfer models, temperature‐based models and artificial neural network (ANN) models generally perform well for areas with a temperate climate. This study evaluates the applicability of these models in estimating hourly and daily evaporation rates for an area with an equatorial climate. Unlike in temperate regions, solar radiation was found to correlate best with pan evaporation on both the hourly and daily time‐scales. Relative humidity becomes a significant factor on a daily time‐scale. Among the simplified models, only the radiation‐based models were found to be applicable for modelling the hourly and daily evaporations. ANN models are generally more accurate than the simplified models if an appropriate network architecture is selected and a sufficient number of data points are used for training the network. ANN modelling becomes more relevant when both the energy‐ and aerodynamics‐driven mechanisms dominate, as the radiation and the mass transfer models are incapable of producing reliable evaporation estimates under this circumstance. Copyright © 2006 John Wiley & Sons, Ltd.  相似文献   

14.
Soil moisture is widely recognized as a fundamental variable governing the mass and energy fluxes between the land surface and the atmosphere. In this study, the soil moisture modelling at sub‐daily timescale is addressed by using an accurate representation of the infiltration component. For that, the semi‐analytical infiltration model proposed by Corradini et al. (1997) has been incorporated into a soil water balance model to simulate the evolution in time of surface and profile soil moisture. The performances of this new soil moisture model [soil water balance module‐semi‐analytical (SWBM‐SA)] are compared with those of a precedent version [SWBM‐Green–Ampt (GA)] where the GA approach was employed. Their capability to reproduce in situ soil moisture observations at three sites in Italy, Spain and France is analysed. Hourly observations of quality‐checked rainfall, temperature and soil moisture data for a 2‐year period are used for testing the modelling approaches. Specifically, different configurations for the calibration and validation of the models are adopted by varying a single parameter, that is, the saturated hydraulic conductivity. Results indicate that both SWBMs are able to reproduce satisfactorily the hourly soil moisture temporal pattern for the three sites with root mean square errors lower than 0.024 m3/m3 both in the calibration and validation periods. For all sites, the SWBM‐SA model outperforms the SWBM‐GA with an average reduction of the root mean square error of ~20%. Specifically, the higher improvement is observed for the French site for which in situ observations are measured at 30 cm depth, and this is attributed to the capability of the SA infiltration model to simulate the time evolution of the whole soil moisture profile. The reasonable models performance coupled with the need to calibrate only a single parameter makes them useful tools for soil moisture simulation in different regions worldwide, also in scarcely gauged areas. Copyright © 2013 John Wiley & Sons, Ltd.  相似文献   

15.
Soil moisture has a pronounced effect on earth surface processes. Global soil moisture is strongly driven by climate, whereas at finer scales, the role of non‐climatic drivers becomes more important. We provide insights into the significance of soil and land surface properties in landscape‐scale soil moisture variation by utilizing high‐resolution light detection and ranging (LiDAR) data and extensive field investigations. The data consist of 1200 study plots located in a high‐latitude landscape of mountain tundra in north‐western Finland. We measured the plots three times during growing season 2016 with a hand‐held time‐domain reflectometry sensor. To model soil moisture and its temporal variation, we used four statistical modelling methods: generalized linear models, generalized additive models, boosted regression trees, and random forests. The model fit of the soil moisture models were R2 = 0.60 and root mean square error (RMSE) 8.04 VWC% on average, while the temporal variation models showed a lower fit of R2 = 0.25 and RMSE 13.11 CV%. The predictive performances for the former were R2 = 0.47 and RMSE 9.34 VWC%, and for the latter R2 = 0.01 and RMSE 15.29 CV%. Results were similar across the modelling methods, demonstrating a consistent pattern. Soil moisture and its temporal variation showed strong heterogeneity over short distances; therefore, soil moisture modelling benefits from high‐resolution predictors, such as LiDAR based variables. In the soil moisture models, the strongest predictor was SAGA (System for Automated Geoscientific Analyses) wetness index (SWI), based on a 1 m2 digital terrain model derived from LiDAR data, which outperformed soil predictors. Thus, our study supports the use of LiDAR based SWI in explaining fine‐scale soil moisture variation. In the temporal variation models, the strongest predictor was the field‐quantified organic layer depth variable. Our results show that spatial soil moisture predictions can be based on soil and land surface properties, yet the temporal models require further investigation. Copyright © 2017 John Wiley & Sons, Ltd.  相似文献   

16.
The analysis of the physical processes involved in a conceptual model of soil water content balance is addressed with the objective of its application as a component of rainfall–runoff modelling. The model uses routinely measured meteorological variables (rainfall and air temperature) and incorporates a limited number of significant parameters. Its performance in estimating the soil moisture temporal pattern was tested through local measurements of volumetric water content carried out continuously on an experimental plot located in central Italy. The analysis was carried out for different periods in order to test both the representation of infiltration at the short time‐scale and drainage and evapotranspiration processes at the long time‐scale. A robust conceptual model was identified that incorporated the Green–Ampt approach for infiltration and a gravity‐driven approximation for drainage. A sensitivity analysis was performed for the selected model to assess the model robustness and to identify the more significant parameters involved in the principal processes that control the soil moisture temporal pattern. The usefulness of the selected model was tested for the estimation of the initial wetness conditions for rainfall–runoff modelling at the catchment scale. Specifically, the runoff characteristics (runoff depth and peak discharge) were found to be dependent on the pre‐event surface soil moisture. Both observed values and those estimated by the model gave good results. On the contrary, with the antecedent wetness conditions furnished by two versions of the antecedent precipitation index (API), large errors were obtained. Copyright © 2007 John Wiley & Sons, Ltd.  相似文献   

17.
Evapotranspiration (ET) is a critical component in the hydrological cycle. However, its actual values appear to be difficult to obtain, especially in areas in which precipitation has high inter‐annual variability. Here, we evaluated eight commonly used ET models in semi‐arid and semi‐humid areas of China. The order of overall performance from best to worst is as follows: the revised Priestley–Taylor model (PT‐JPL, 0.71, 1.65 [18.37%], 4.72 [49.19%]) a a Statistics (model abbreviation, coefficient of determination, bias [relative value], standard deviation [relative value]).
, the modified PT‐JPL model (M1‐PT‐JPL, 0.67, ?0.68 [7.56%], 3.87 [40.31%]), the Community Land Model (CLM, 0.68, ?2.52 [28.01%], 5.10 [53.17%]), the modified PT‐JPL model (M2‐PT‐JPL, 0.63, 0.57 [6.27%], 5.04 [52.52%]), the revised Penman–Monteith model (RS‐PM, 0.62, 3.56 [37.40%], 6.11 [63.68%]), an empirical model (Wang, 0.59, ?1.04 [11.57%], 5.61 [58.43%]), the advection‐aridity model (AA, 0.55, 5.56 [61.78%], 7.45 [77.60%]), and the energy balance model (SEBS, 0.35, 5.11 [56.72%], 9.43 [98.18%]). The performance of all of the models is comparably poor in winter and summer, except for the PT‐JPL model, and relatively good in spring and autumn. Because of the vegetation control on ET, the Wang, RS‐PM, PT‐JPL, M1‐PT‐JPL, and M2‐PT‐JPL models perform better for cropland, whereas the AA model, SEBS model and CLM perform better for grassland. The CLM, PT‐JPL, and Wang models perform better in semi‐arid region than in semi‐humid region, whereas the opposite is true for SEBS and RS‐PM. The AA, M1‐PT‐JPL, and M2‐PT‐JPL models perform similarly in semi‐arid and semi‐humid regions. When considering the inter‐annual variability in precipitation, the Wang model has relatively good performance under only some annual precipitation conditions; the performance of the PT‐JPL and AA models is reduced under conditions of high precipitation; the two modified PT‐JPL models inherited the steady performance of the PT‐JPL model and improved the performance under conditions of high annual precipitation by the modification of the soil moisture constraint. RS‐PM is more appropriate for humid conditions. CLM and PT‐JPL models could be effectively applied to all precipitation conditions because of their good performance across a wide annual precipitation range. Copyright © 2016 John Wiley & Sons, Ltd.  相似文献   

18.
Hydrologic models are useful to understand the effects of climate and land‐use changes on dry‐season flows. In practice, there is often a trade‐off between simplicity and accuracy, especially when resources for catchment management are scarce. Here, we evaluated the performance of a monthly rainfall–runoff model (dynamic water balance model, DWBM) for dry‐season flow prediction under climate and land‐use change. Using different methods with decreasing amounts of catchment information to set the four model parameters, we predicted dry‐season flow for 89 Australian catchments and verified model performance with an independent dataset of 641 catchments in the United States. For the Australian catchments, model performance without catchment information (other than climate forcing) was fair; it increased significantly as the information to infer the four model parameters increased. Regressions to infer model parameters from catchment characteristics did not hold for catchments in the United States, meaning that a new calibration effort was needed to increase model performance there. Recognizing the interest in relative change for practical applications, we also examined how DWBM could be used to simulate a change in dry‐season flow following land‐use change. We compared results with and without calibration data and showed that predictions of changes in dry‐season flow were robust with respect to uncertainty in model parameters. Our analyses confirm that climate is a strong driver of dry‐season flow and that parsimonious models such as DWBM have useful management applications: predicting seasonal flow under various climate forcings when calibration data are available and providing estimates of the relative effect of land use on seasonal flow for ungauged catchments.  相似文献   

19.
Active microwave remote sensing observations of backscattering, such as C‐band vertically polarized synthetic aperture radar (SAR) observations from the second European remote sensing (ERS‐2) satellite, have the potential to measure moisture content in a near‐surface layer of soil. However, SAR backscattering observations are highly dependent on topography, soil texture, surface roughness and soil moisture, meaning that soil moisture inversion from single frequency and polarization SAR observations is difficult. In this paper, the potential for measuring near‐surface soil moisture with the ERS‐2 satellite is explored by comparing model estimates of backscattering with ERS‐2 SAR observations. This comparison was made for two ERS‐2 overpasses coincident with near‐surface soil moisture measurements in a 6 ha catchment using 15‐cm time domain reflectometry probes on a 20 m grid. In addition, 1‐cm soil moisture data were obtained from a calibrated soil moisture model. Using state‐of‐the‐art theoretical, semi‐empirical and empirical backscattering models, it was found that using measured soil moisture and roughness data there were root mean square (RMS) errors from 3·5 to 8·5 dB and r2 values from 0·00 to 0·25, depending on the backscattering model and degree of filtering. Using model soil moisture in place of measured soil moisture reduced RMS errors slightly (0·5 to 2 dB) but did not improve r2 values. Likewise, using the first day of ERS‐2 backscattering and soil moisture data to solve for RMS surface roughness reduced RMS errors in backscattering for the second day to between 0·9 and 2·8 dB, but did not improve r2 values. Moreover, RMS differences were as large as 3·7 dB and r2 values as low as 0·53 between the various backscattering models, even when using the same data as input. These results suggest that more research is required to improve the agreement between backscattering models, and that ERS‐2 SAR data may be useful for estimating fields‐scale average soil moisture but not variations at the hillslope scale. Copyright © 2004 John Wiley & Sons, Ltd.  相似文献   

20.
Infiltration into frozen soil is a key hydrological process in cold regions. Although the mechanisms behind point‐scale infiltration into frozen soil are relatively well understood, questions remain about upscaling point‐scale results to estimate hillslope‐scale run‐off generation. Here, we tackle this question by combining laboratory, field, and modelling experiments. Six large (0.30‐m diameter by 0.35‐m deep) soil cores were extracted from an experimental hillslope on the Canadian Prairies. In the laboratory, we measured run‐off and infiltration rates of the cores for two antecedent moisture conditions under snowmelt rates and diurnal freeze–thaw conditions observed on the same hillslope. We combined the infiltration data with spatially variable data from the hillslope, to parameterise a surface run‐off redistribution model. We used the model to determine how spatial patterns of soil water content, snowpack water equivalent (SWE), and snowmelt rates affect the spatial variability of infiltration and hydrological connectivity over frozen soil. Our experiments showed that antecedent moisture conditions of the frozen soil affected infiltration rates by limiting the initial soil storage capacity and infiltration front penetration depth. However, shallow depths of infiltration and refreezing created saturated conditions at the surface for dry and wet antecedent conditions, resulting in similar final infiltration rates (0.3 mm hr?1). On the hillslope‐scale, the spatial variability of snowmelt rates controlled the development of hydrological connectivity during the 2014 spring melt, whereas SWE and antecedent soil moisture were unimportant. Geostatistical analysis showed that this was because SWE variability and antecedent moisture variability occurred at distances shorter than that of topographic variability, whereas melt variability occurred at distances longer than that of topographic variability. The importance of spatial controls will shift for differing locations and winter conditions. Overall, our results suggest that run‐off connectivity is determined by (a) a pre‐fill phase, during which a thin surface soil layer wets up, refreezes, and saturates, before infiltration excess run‐off is generated and (b) a subsequent fill‐and‐spill phase on the surface that drives hillslope‐scale run‐off.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号