首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献，搜索用时 15 毫秒
1.
Heavy metals are a threat to human health and ecosystem. These days, great deal of attention is being given to green technologies for purification of water contaminated with heavy metal ions. Biosorption is one among such emerging technologies, which utilizes naturally occurring waste materials to sequester heavy metals from wastewater. Cadmium has hazardous impact on living beings; therefore, its removal through green and economical process is an important task. The aim of the present study was to utilize the locally available Portulaca oleracea plant biomass as an adsorbent for cadmium removal from aqueous solution. The biomass was obtained after drying and grinding the portulaca leaves and stem. No chemical treatment was done on the adsorbent so that it remained green in a true sense. Batch experiments were performed at room temperature. The critical parameters studied were effects of pH, contact time, initial metal ion concentration and adsorbent dose on the adsorption of cadmium. The maximum adsorption was found to be 72 %. The kinetic data were found to best fit the pseudo-second-order equation. High adsorption rates were obtained in the initial 45 min, and adsorption equilibrium was then gradually achieved in about 100 min. Adsorption increased with increase in pH for a range 2 and 6. The equilibrium adsorption results closely followed both the Langmuir and Freundlich isotherms. The values of constants were calculated from isotherms. Results indicated that portulaca plant biomass could be developed as a potential material to be used in green water treatment devices for removal of metal ions.  相似文献   

2.
Analysis was carried out using tangerine peel aiming its use as a potential adsorbent of eight heavy metal ions (Cd, Co, Cr, Cu, Mn, Ni, Pb and Zn) from aqueous solution. This agricultural waste was tested both in its untreated and also chemically modified form. Based on Fourier transformation infrared spectra, a comparison of biosorbent structure before and after chemical treatment was made. Batch adsorption tests were conducted at different pH and mass of sorbent to examine the influence on the effectiveness of simultaneous removal of tested ions. Kinetic studies were conducted at optimum pH 5.0 and sorbent dosage 300 mg. The pseudo-second-order kinetic model best fit the experimental data with high correlation coefficients (r2 > 0.9997). By optimizing listed parameters, high removal efficiencies (> 89%) were achieved. According to the results obtained in this study, the remediation of water polluted with heavy metals could be done using modified tangerine peel as an agricultural waste material.  相似文献   

3.
A novel adsorbent for heavy metal remediation in aqueous environments   总被引：9，自引：8，他引：1  
The objective of this study was to investigate the possibility of using maize tassel as an alternative adsorbent for the removal of chromium (VI) and cadmium (II) ions from aqueous solutions. The effect of pH, solution temperature, contact time, initial metal ion concentration and adsorbent dose on the adsorption of chromium (VI) and cadmium (II) by tassel was investigated using batch methods. Adsorption for both chromium (VI) and cadmium (II) was found to be highly pH dependent compared to the other parameters investigated. Obtained results gave an adsorption capacity of 79.1 % for chromium (VI) at pH 2, exposure time of 1h at 25 °C. Maximum capacity of cadmium of 88 % was obtained in the pH range of 5-6 at 25 °C after exposure time of 1 h. The adsorption capacities of tassel for both chromium (VI) and cadmium (II) were found to be comparable to those of other commercial adsorbents currently in use for the removal of heavy metals from aqueous wastes. These results have demonstrated the immense potential of maize tassel as an alternative adsorbent for toxic metal ions remediation in polluted water and wastewater.  相似文献   

4.
Zeolites are known to possess valuable physiochemical properties such as adsorption, cation exchange, molecular sieving, and catalysis. In addition, zeolites are highly selective scavengers of a variety of heavy metals from liquid effluents through the process of ion exchange. The present study was performed to hydrothermally synthesize Na8[AlSiO4]6(OH)2·2H2O (also known as hydroxy sodalite hydrate). Due to its small aperture size, this material can be an ideal candidate for the separation of small molecules and ions from aquatic and gas mixtures. Synthetic zeolites offer many advantages over natural zeolites, such as higher ion affinity and adsorption capacity. Batch adsorption isotherm studies were conducted to evaluate the obtained adsorbent for the lead ion removal from aqueous media. Modeling lead ion adsorption using Langmuir and Freundlich isotherm expressions determined the capacity of the adsorbent. A removal efficiency of 98.1 % in a 3.0 g/l adsorbent/solution mixture with a maximum adsorption capacity of 153.8 mg/g was obtained. One potential application of the synthesized zeolite is for the lead removal in point-of-use treatment devices.  相似文献   

5.
As, Hg and Pb are examples of heavy metals which are present in different types of industrial effluents responsible for environmental pollution. Their removal is traditionally made by chemical precipitation, ion-exchange and so on. However, this is expensive and not completely feasible to reduce their concentrations to the levels as low as required by the environmental legislation. Biosorption is a process in which solids of natural origin are employed for binding the heavy metal. It is a promising alternative method to treat industrial effluents, mainly because of its low cost and high metal binding capacity. The kinetics was studied for biosorption experiments using coconut fiber for As (III), Hg (II) and Pb (II) ions adsorption. The specific surface area and surface charge density of the coconut fiber are 1.186×1025 (m2/g) and 5.39 ×1024 (meq/m2), respectively. The maximum adsorption capacity was found to be the highest for Pb (II) followed by Hg (II) and As (III). The modification of the adsorbent by thiolation affected the adsorption capacity. Equilibrium sorption was reached for the metal ions at about 60 min. The equilibrium constant and free energy of the adsorption at 30 °C were calculated. The mechanism of sorption was found to obey the particle-diffusion model. The kinetic studies showed that the sorption rates could be described by both pseudo first-order and pseudo second-order models. The pseudo second-order model showed a better fit with a rate constant value of 1.16 × 10?4/min. for all three metal ions. Therefore, the results of this study show that coconut fiber, both modified and unmodified, is an efficient adsorbent for the removal of toxic and valuable metals from industrial effluents.  相似文献   

6.
In this study, the feasibility of using a low-cost adsorbent mixture composed of leonardite (L) and clinoptilolite (C) was evaluated by batch adsorption method using different parameters such as mixing ratio, contact time, pH, temperature, and adsorbent amount for the removal of Zn (II) ions from an aqueous solution. The adsorbents were characterized by X-ray diffraction, Fourier transform infrared spectroscopy, and Raman spectroscopy. Additionally, leonardite–clinoptilolite mixture was analyzed by scanning electron microscopy coupled with energy dispersive X-ray. The Zn (II) adsorption along with an unprecedented adsorption capacity of 454.55 mg g?1 for unmodified natural sorbents was obtained by mixing leonardite and clinoptilolite (LC) without any pretreatment at a ratio of 3:1, using 0.1 g of sorbent at a pH 6, for 2 h of contact time. The experimental data showed a good fit for the Langmuir isotherm model. The thermodynamic parameters revealed that the present adsorption process was spontaneous and exothermic in nature (25–50 °C). The kinetic results of the adsorption showed that the Zn (II) adsorption onto the LC follows pseudo-second-order model. The resultant LC mixture has an excellent adsorption capacity of a Zn (II) aqueous solution, and data obtained may form the basis for utilization of LC as an unpretreated low-cost adsorbent for treatment of metalliferous industrial wastewater.  相似文献   

7.
The use of agricultural wastes as biosorbents is gaining importance in bioremediation of heavy metal-polluted water and soils, due to their effectiveness and low cost. This work assesses the Cd, Pb and Cu adsorption capacity of the raw materials used in the production of substrates for mushroom production (Agaricus bisporus and Pleurotus ostreatus) and the spent mushroom composted (SMC), based on the functional groups of their organic carbon. The raw materials studied included agricultural wastes (wheat straw, wheat and rice poultry litter, grape pomace) and inorganic substances (gypsum and calcareous sand). Organic carbon from wastes and their composting products were characterized by CP-MAS 13C NMR. Langmuir adsorption isotherms of metals were plotted for each raw material, composting step, spent A. bisporus and P. ostreatus substrates and the final SMC. The maximum adsorption capacities of SMC were 40.43, 15.16 and 36.2 mg g?1 for Cd, Pb and Cu, respectively. The composting process modified the adsorption properties of raw materials because of the enhanced adsorption of Cd and Cu and decreased adsorption capacity of Pb. CP-MAS 13C NMR and potentiometric titration were used to identify the functional groups of the organic carbon responsible for the metal adsorption. The content of cellulose was correlated with Pb adsorption (p < 0.001), alkyl and carboxyl carbon with Cd adsorption (p < 0.001), and N-alkyl (p < 0.001) and carboxyl (p < 0.010) groups with Cu adsorption. These results are valuable to develop new biosorbents based on agricultural wastes and demonstrate the high potential of SMC to adsorb heavy metals from polluted environments.  相似文献   

8.
In the present research, the removal of lead(II) and copper(II) from aqueous solutions is studied, using SnO2 nanowires as new adsorbent on solid-phase extraction disk and compared with pine core and buttonwood as biosorbents. Batch adsorption experiments were performed as a function of pH, adsorption time, solute concentration and adsorbent dose for biosorbents. Also, the pH, transfer rate of solution and metal concentration were selected as experimental parameters for the removal of heavy metals by SnO2 nanowires. All of the parameters were optimized by experimental design method for sorbents. The experimental equilibrium adsorption data are tested for the Langmuir and Freundlich equations. Results indicate the following order to fit the isotherms: Langmuir > Freundlich, in case of lead and copper ions. The removal of Cu(II) and Pb(II) was performed by selected sorbents in the presence of interferences ions. This led to no remarkable decrease in the removal efficiency of SnO2 nanowires. Using the SnO2 nanowires in the wastewater treatment indicated 96.8 and 85.28% removal efficiency in only 7 min for Pb(II) and Cu(II), respectively. SnO2 nanowires were found as reusable sorbent. Therefore, SnO2 nanowires have a good potential for application in environmental protection.  相似文献   

9.
The ability of ochre to remove Pb(II) and Cu(II) from aqueous media has been studied by batch sorption studies varying the contact time, initial metal concentration, initial solution pH and temperature to understand the adsorption behaviour of these metals through adsorption kinetics and isotherms. The pH of the solution and the temperature controlled the adsorption of metal ions by ochre and rapid uptake occurred in the first 30 min of reaction. The kinetics of adsorption followed a pseudo-second-order rate equation (R 2 > 0.99) and the isotherms are well described by the Freundlich model. Adsorption of metals onto ochre is endothermic in nature. Between the two metals, Pb(II) showed more preference towards the exchangeable sites on ochre than Cu(II). This study indicates that ochre is a very effective adsorbent in removing Pb(II) and Cu(II) from the aqueous environment with an adsorptive capacity of 0.996 and 0.628 mg g?1 and removal efficiency of 99.68 and 62.80 %, respectively.  相似文献   

10.
Homogenized samples of raw clays resulting from two (2) different lots of natural clays from Maghnia (Algeria) have been assessed for their potential use in the removal of Pb2+ and Zn2+ ions from industrial liquid wastes (LW). Raw and acid-activated samples have been characterized by powder X-ray diffraction, FT-IR spectroscopy, electron microscopy (SEM), and X-ray fluorescence (XRF) and used as adsorbents for the removal of Pb2+ and Zn2+ ions from aqueous system using adsorption method under different conditions. The effect of factors including contact time, pH, and dosage on the adsorption properties of Pb2+ and Zn2+ ions onto clays was investigated at 25 °C. The obtained results revealed that the removal percentages of Pb2+ and Zn2+ ions, from both aqueous solution (AS) and LW, were varying between 90 and 98% for 40 min and optimal pH values ranged from 5 to 6 for Pb2+ and Zn2+ ions, respectively. The kinetics of both Pb2+ and Zn2+ ion adsorption fitted well with the pseudo-second-order model. Langmuir, Freundlich, and Temkin adsorption isotherms were used, and their constants were evaluated. The values of thermodynamic parameters, ΔH°, ΔS°, and ΔG° indicated that the adsorption of Pb2+ and Zn2+ ions was spontaneous and exothermic process in nature. The adsorption and desorption isotherms indicated that Pb2+ and Zn2+ adsorption to raw clays was reversible. The experimental results obtained showed that the raw clays from Maghnia (Algeria) had a great potential for removing Pb2+ and Zn2+ ions from industrial liquid wastes using adsorption method.  相似文献   

11.
Vitis vinifera (grape) leaf litter, an abundant agricultural waste in South Africa was chemically modified with H3PO4 and carbonized for use as biosorbent. Characterization and the potential application of the adsorbent in simultaneous removal of 4-nitrophenol and 2-nitrophenol from aqueous solutions were investigated. The adsorbent was characterized using FTIR, SEM and EDX elemental microanalysis. The EDX and FTIR analysis revealed the presence of surface oxygen moieties capable of binding to adsorbate molecules while the SEM micrographs showed the development of pores and cavities in the adsorbent. Batch adsorption experiments were conducted at a varying contact time, adsorbent dosage, pH and initial adsorbate concentration to investigate optimal conditions. The maximum adsorption capacity of the adsorbent was 103.09 and 103.10 mg/g for 4-nitrophenol and 2-nitrophenol, respectively. The adsorption process was best fitted into Freundlich isotherm while the adsorption kinetics followed a pseudo-second-order model. Liquid film and intra-particle diffusion contributed to the adsorption process. Thermodynamic parameters of ΔG°, ΔH° and ΔS° were evaluated. The adsorption was exothermic, feasible and spontaneous. The results suggest a possible application of grape leaf litter as a precursor for activated carbon and for cheaper wastewater treatment technologies.  相似文献   

12.
The adsorption of cadmium (Cd) and zinc (Zn) with similar chemical properties is examined onto three soil samples: one is alkaline and the others are acidic. The distribution coefficient (K d) and the Freundlich constant (K F) for Zn are slightly higher than those for Cd, implying that the adsorption affinity of Zn is a little greater and less mobile. However, Cd and Zn usually show comparable results in the kinetic, isotherm, and envelope experiments. The adsorption of the heavy metals is relatively rapid and the reaction is almost completed within 15 min. The kinetics for both Cd and Zn are very well explained by the parabolic diffusion model. The maximum adsorption of the heavy metals is obtained at high pH, high temperature, and low ionic strength. The adsorption capacity on the alkaline soil is more significantly affected by the temperature as compared to the acidic soil. It is found that the adsorption affinity of the two heavy metals is mainly affected by the soil properties, such as pH, pHPZC, organic matter, and total carbon. It is also confirmed that the chemical properties of the heavy metals are important factors in their adsorption onto soil. The adsorption isotherms of Cd and Zn are well described in both Freundlich and Langmuir models at the usual pH (soil pH). Under acidic and alkaline pHs, however, only the Freundlich model describes the adsorption of both heavy metals satisfactorily.  相似文献   

13.
This research is focused on evaluating heavy metals (Cd, Cu, Fe, Mn, Pb, and Zn) uptake and removal by Eleocharis ovata, Cyperus manimae, Typha dominguensis, and Pteridium aquilinum in a natural wetland impacted by mining activities. We analyzed heavy metals content and distribution in native plants, soils, and water of a semipermanent natural wetland in Taxco de Alarcón, Guerrero, and we also determined the physicochemical characteristics of the water. Translocation factor (TF) and bioconcentration factor (BCF) were evaluated. Results showed that physical and chemical conditions are favorable for plants development. Correlation analysis showed a good and positive relation (0.95) between Cu and Pb in soils and plants. In the analyzed matrices: Zn (0.62–2.20 mg/L) exceeded the permissible limits in water, high concentrations of Pb and Zn (26.57–525.67 and 266.67–983.33 mg/kg, respectively) were detected in the studied soils, and Pb exceeded the normal range for E. ovata and P. aquilinum in the analyzed plants. Uptake of heavy metals in the tissues of different species was found in the following order: root > leaf. Data of TF and BCF showed that E. ovata is a tolerant plant with respect to heavy metals exposure since TF value was greater than 1. This study showed that E. ovata could be considered as a bioaccumulator of heavy metals in contaminated soils.  相似文献   

14.
This work aimed to investigate the adsorption characteristics, both kinetically and thermodynamically, of Cu(II) and Pb(II) removal from aqueous solutions onto mixed-waste activated carbon, as well as to study the competitive behavior found in mixed heavy metal solution systems. This study shows that activated carbon prepared from mixed waste is an effective adsorbent for the removal of Cu(II) and Pb(II) from aqueous solutions, with the aim of detoxifying industrial effluents before their safe disposal onto water surfaces. The adsorption process was characterized in terms of kinetic and thermodynamic studies. In addition, the influence of presence of Cu(II) and Pb(II) in a competitive system was investigated. The results showed that the maximum adsorption capacities were gained at a pH of 6 with a contact time of 180 min, a metal solution concentration of 300 ppm, and an adsorbent dose of 0.3 g/L. The adsorption process was found to follow a pseudo-first-order kinetic model. Thermodynamic parameters such as ΔG o, ΔH o, and ΔS o showed that the sorption process was spontaneous and endothermic in nature. A competitive study demonstrated the applicability of mixed-waste activated carbon to adsorb Cu(II) and Pb(II) from a solution of mixed metals. In addition, the adsorption capacity was found to be as effective as other adsorbents reported in the literature. The developed adsorptive removal procedure was applied for treatment of real wastewater samples and showed high removal efficiency.  相似文献   

15.
Contamination with heavy metals in surface and groundwater is a threat to human health and ecosystems. Due to this, the need arises to remediate water polluted through ecological and profitable technologies, such as phytoremediation. The objective of the work was to evaluate the concentration of lead (Pb) and zinc (Zn) in the floating macrophytes Limnobium laevigatum and Ludwigia peploides, after being exposed to contaminated water experimentally. In this way to be able to determine if these plants have mechanisms that allow them to accumulate the metals in the roots and to perform the translocation of these to different vegetative organs, L. laevigatum and L. peploides were placed in solutions contaminated with Pb ([Pb]?=?5 mg/l) and Zn ([Zn]?=?20 mg/l). The concentrations of metals in water, root and leaf samples were evaluated as a function of time (0, 1, 2 and 4 days). The determination of the metals was performed by the atomic absorption spectrophotometry technique. After 4 days of exposure to Pb and Zn, the plants showed high metal removal efficiencies of water, more to 70% in all cases. Pb was accumulated fundamentally by roots, while Zn was accumulated more in the leaves. In addition, the bioconcentration and translocation factors for each metal were calculated.  相似文献   

16.
At present, there is growing interest in using low cost, commercially available materials for the adsorption of heavy metals. The major advantages of adsorption technologies are its effectiveness in reducing the concentration of heavy metal ions to very low levels and the use of inexpensive adsorbent materials. In this review, agricultural and forest waste adsorbents were used to remove Pb2+ ions in wastewater treatment, and their technical feasibilities were reviewed in studies mainly from 2000 to 2010. They all were compared with each other by metal binding capacities, metal removal performances, sorbent dose, optimum pH, temperature, initial concentration and contact time. Although commercial activated carbon is widely used in wastewater treatment applications, it has high costs. The use of agricultural by-products as adsorbent material to purify heavy metal contaminated water has become increasingly popular through the past decade because they are less expensive, biodegradable, abundant and efficient. Instead of activated carbon, this study was focused on the inexpensive materials such as agricultural and forest waste. It was shown that these alternative adsorbents had sufficient binding capacity to remove Pb2+ ions from wastewater.  相似文献   

17.
Dynamics of heavy metals in the surface sediments of Mahanadi river estuarine system were studied for three different seasons. This study demonstrates that the relative abundance of these metals follows in the order of Fe > Mn > Zn > Pb > Cr > Ni ≥ Co > Cu > Cd. The spatial pattern of heavy metals supported by enrichment ratio data, suggests their anthropogenic sources possibly from various industrial wastes and municipal wastes as well as agricultural runoff. The metal concentrations in estuarine sediments are relatively higher than in the river due to adsorption/accumulation of metals on sediments during saline mixing, while there is a decreasing trend of heavy metal concentrations towards the marine side. The temporal variations for metals, such as Fe, Mn, Zn, Ni and Pb exhibit higher values during monsoon season, which are related to agricultural runoff. Higher elemental concentrations are observed during pre-monsoon season for these above metals (except Ni) at the polluted stations and for metals, such as Cr, Co and Cd at all sites, which demonstrate the intensity of anthropogenic contribution. R-mode factor analysis reveals that “Fe–Mn oxy hydroxide”, “organic matter”, “CaCO3”, and “textural variables” factors are the major controlling geochemical factors for the enrichment of heavy metals in river estuarine sediment and their seasonal variations, though their intensities were different for different seasons. The relationships among the stations are highlighted by cluster analysis, represented in dendrograms to categorize different contributing sites for the enrichment of heavy metals in the river estuarine system.  相似文献   

18.
In this study, the adsorption behavior of Ni(II) in an aqueous solution system using natural adsorbent Peganum harmala-L was measured via batch mode. The prepared sorbent was characterized by scanning electron microscope, Fourier transform infrared spectroscopy, N2 adsorption–desorption and pHzpc. Adsorption experiments were carried out by varying several conditions such as contact time, metal ion concentration and pH to assess kinetic and equilibrium parameters. The equilibrium data were analyzed based on the Langmuir, Freundlich, Temkin and Dubinin–Radushkevich isotherms. Kinetic data were analyzed using the pseudo-first-order, pseudo-second-order and intra-particular diffusion models. Experimental data showed that at contact time 60 min, metal ion concentration 50 mg/L and pH 6, a maximum amount of Ni(II) ions can be removed. The experimental data were best described by the Langmuir isotherm model as is evident from the high R 2 value of 0.988. The adsorption capacity (q m) obtained was 68.02 mg/g at an initial pH of 6 and a temperature of 25 °C. Kinetic studies of the adsorption showed that equilibrium was reached within 60 min of contact and the adsorption process followed the pseudo-first-order model. The obtained results show that P. harmala-L can be used as an effective and a natural low-cost adsorbent for the removal of Ni(II) from aqueous solutions.  相似文献   

19.
Amorphous tin(VI) hydrogen phosphate (ATHP) was synthesized using the liquid phase precipitation method and served as an adsorbent to remove Pb(II), Cu(II), and Zn(II) from aqueous solutions. The ATHP was characterized by powder X-ray diffraction (XRD), transmission electron microscopy (TEM), scanning electron microscopy (SEM), X-ray photoelectron spectroscopy (XPS), and nitrogen adsorption–desorption techniques. Adsorption properties were evaluated as a function of pH, reaction time, concentration of reactants, and salinity. Their equilibrium adsorption data were modeled using Freundlich, Langmuir, and Dubinin–Kaganer–Radushkevich isotherms, respectively. The results revealed that adsorption equilibrium reached within 180 min. ATHP indicated good adsorption even below the pHZPC, and best adsorption at pH 5 for Pb(II) and Cu(II) and at pH 5.5 for Zn(II) was observed. Equilibrium data fitted better to the Langmuir model for Pb(II) and Cu(II) and fitted better to the Freundlich model for Zn(II). The saturated adsorption capacities deduced from the Langmuir model were 2.425, 1.801, and 0.600 mmol/g for Cu(II), Pb(II), and Zn(II), respectively, indicating an adsorption affinity order of Cu > Pb > Zn. There is a negative correlation between the concentration of NaCl and adsorption capacity of ATHP, yet ATHP still exhibited excellent adsorption having an adsorption capacity of 19.35, 15.16, 6.425 mg/g when the concentration of NaCl was 0.6 mol/L. The free energy (E) was 12.33, 10.70, and 14.74 kJ/mol for Pb(II), Cu(II), and Zn(II), respectively. An adsorption mechanism based on ion exchange between heavy metal ions and H+ in the ATHP is proposed. Furthermore, the used ATHP was regenerated by HCl solution and the adsorbent was used repeatedly.  相似文献   

20.
The objective of the present study is to evaluate the absorption efficacy of H. fusiformis biochar (HFB) for the removal of phenol and heavy metals from single and mixed solute systems of these species under different experimental conditions. The effects of contact time, pH change, initial phenol concentration, and heavy metal concentration on the adsorption capacity of HFB were investigated. The kinetics and equilibrium models of sorption of the components of the single and mixed solute systems on HFB were also studied. The experimental data were fitted to kinetic and equilibrium models. The batch experiments revealed that 360 min of contact time was sufficient to achieve equilibrium for the adsorption of both phenol and heavy metals. The adsorption of phenol and nickel by HFB followed the pseudo-second-order kinetic model, which was quite adequate for describing the adsorption mechanism. The equilibrium data for the adsorption of phenol and heavy metals fit well to the Langmuir model with regression coefficients of R 2 > 0.819. The maximum Langmuir adsorption capacities were 10.39, 12.13, 22.25, 2.24, 2.89, and 22.03 mg/g for phenol, Ni2+, Zn2+, Cu2+, Pb2+, and Cd2+, respectively. Moreover, HFB exhibited optimal sorption under slightly acidic conditions at pH 6. The HFB used in the present study exhibited higher adsorption capacity for the removal of phenol and heavy metals from aqueous solutions compared to documented sorbents. These results demonstrate that HFB is potentially useful for alleviating the harmful effects of phenol and heavy metal in wastewater treatment systems.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号