共查询到20条相似文献，搜索用时 46 毫秒
1.
《国际泥沙研究》2010,(4)
This paper presents a computational fluid dynamics model for simulation of twodimensional (2-D) water flow, sediment transport, bank failure processes, and the subsequent channel pattern changes. Effects of secondary currents at channel bends are included in the modified momentum conservation equation of water flow. An improved bank failure model is applied to calculate bank failure due to riverbed erosion, and to simulate lateral migration and planform changes of alluvial channels. The water flow model has been validated using laboratory measurements of flow in consecutive bends designed by the authors, in addition to flume test data from the literature. 相似文献
2.
The paper presents the development of a morphological model and its application to experimental model rivers.The model takes into account the key processes of channel migration,including bed deformation,bank failure and wetting and drying.Secondary flows in bends play an important role in lateral sediment transport,which further affects channel migration.A new formula has been derived to predict the near-bed secondary flow speed,in which the magnitude of the speed is linked to the lateral water level gradient.Since only non-cohesive sediment is considered in the current study,the bank failure is modelled based on the concept of submerged angle of repose.The wetting and drying process is modelled using an existing method.Comparisons between the numerical model predictions and experimental observations for various discharges have been made.It is found that the model predicted channel planform and cross-sectional shapes agree generally well with the laboratory observations.A scenario analysis is also carried out to investigate the impact of secondary flow on the channel migration process.It shows that if the effect of secondary flow is ignored,the channel size in the lateral direction will be seriously underestimated. 相似文献
3.
Rill bank collapse is an important component in the adjustment of channel morphology to changes in discharge and sediment flux. Sediment inputs from bank collapse cause abrupt changes in flow resistance, flow patterns and downstream sediment concentrations. Generally, bank retreat involves gradual lateral erosion, caused by flow shear stress, and sudden bank collapse, triggered by complex interactions between channel flow and bank and soil water conditions. Collapse occurs when bank height exceeds the critical height where gravitational forces overcome soil shear strength. An experimental study examined conditions for collapse in eroding rill channels. Experiments with and without a deep water table were carried out on a meandering rill channel in a loamy sand and sandy loam in a laboratory flume under simulated rainfall and controlled runon. Different discharges were used to initiate knickpoint and rill incision. Soil water dynamics were monitored using microstandpipes, tensiometers and time domain reflectometer probes (TDR probes). Bank collapse occurred with newly developed or rising pre‐existing water tables near rill banks, associated with knickpoint migration. Knickpoint scour increased effective bank height, caused positive pore water pressure in the bank toe and reduced negative pore pressures in the unsaturated zone to near zero. Matric tension in unsaturated parts of the bank and a surface seal on the ‘interrill’ zone behind the bank enhanced stability, while increased effective bank height and positive pore water pressure at the bank toe caused instability. With soil water contents >35 per cent (sandy loam) and >23 per cent (loamy sand), critical bank heights were 0·11–0·12 m and 0·06–0·07 m, respectively. Bank toe undercutting at the outside of the rill bends also triggered instability. Bank displacement was quite different on the two soils. On the loamy sand, the failed block slid to the channel bed, revealing only the upper half of the failure plane, while on the sandy loam the failed block toppled forwards, exposing the failure plane for the complete bank height. This study has shown that it is possible to predict location, frequency and magnitude of the rill bank collapse, providing a basis for incorporation into predictive models for hillslope soil loss or rill network development. Copyright © 2006 John Wiley & Sons, Ltd. 相似文献
4.
Three‐dimensional flow structure and patterns of bed shear stress in an evolving compound meander bend 
下载免费PDF全文
下载免费PDF全文 Compound meander bends with multiple lobes of maximum curvature are common in actively evolving lowland rivers. Interaction among spatial patterns of mean flow, turbulence, bed morphology, bank failures and channel migration in compound bends is poorly understood. In this paper, acoustic Doppler current profiler (ADCP) measurements of the three‐dimensional (3D) flow velocities in a compound bend are examined to evaluate the influence of channel curvature and hydrologic variability on the structure of flow within the bend. Flow structure at various flow stages is related to changes in bed morphology over the study timeframe. Increases in local curvature within the upstream lobe of the bend reduce outer bank velocities at morphologically significant flows, creating a region that protects the bank from high momentum flow and high bed shear stresses. The dimensionless radius of curvature in the upstream lobe is one‐third less than that of the downstream lobe, with average bank erosion rates less than half of the erosion rates for the downstream lobe. Higher bank erosion rates within the downstream lobe correspond to the shift in a core of high velocity and bed shear stresses toward the outer bank as flow moves through the two lobes. These erosion patterns provide a mechanism for continued migration of the downstream lobe in the near future. Bed material size distributions within the bend correspond to spatial patterns of bed shear stress magnitudes, indicating that bed material sorting within the bend is governed by bed shear stress. Results suggest that patterns of flow, sediment entrainment, and planform evolution in compound meander bends are more complex than in simple meander bends. Moreover, interactions among local influences on the flow, such as woody debris, local topographic steering, and locally high curvature, tend to cause compound bends to evolve toward increasing planform complexity over time rather than stable configurations. Copyright © 2016 John Wiley & Sons, Ltd. 相似文献
5.
We develop a new method for analysis of meandering channels based on planform sinuosity. This analysis objectively identifies three channel‐reach lengths based on sinuosity measured at those lengths: the length of typical, simple bends; the length of long, often compound bends; and the length of several bends in sequence that often evolve from compound bends to form multibend loops. These lengths, when normalized by channel width, tend to fall into distinct and clustered ranges for different natural channels. Mean sinuosity at these lengths also falls into distinct ranges. That range is largest for the third and greatest length, indicating that, for some streams, multibend loops are important for planform sinuosity, whereas for other streams, multibend loops are less important. The role of multibend loops is seldom addressed in the literature, and they are not well predicted by previous modelling efforts. Also neglected by previous modelling efforts is bank–flow interaction and its role in meander evolution. We introduce a simple river meandering model based on topographic steering that has more in common with cellular approaches to channel braiding and landscape evolution modelling than to rigorous, physics‐based analyses of river meandering. The model is sufficient to produce reasonable meandering channel evolution and predicts compound bend and multibend loop formation similar to that observed in nature, in both mechanism and importance for planform sinuosity. In the model, the tendency to form compound bends is sensitive to the relative magnitudes of two lengths governing meander evolution: (i) the distance between the bend cross‐over and the zone of maximum bank shear stress, and (ii) the bank shear stress dissipation length related to bank roughness. In our simple model, the two lengths are independent. This sensitivity implies that the tendency for natural channels to form compound bends may be greater when the banks are smoother. Copyright © 2002 John Wiley & Sons, Ltd. 相似文献
6.
River restoration projects have installed j‐hook deflectors along the outer bank of meander bends to reduce hydraulic erosion, and in this study we use a computational fluid dynamics (CFD) model to document how these deflectors initiate changes in meander hydrodynamics. We validated the CFD with streamwise and cross‐channel bankfull velocities from a 193° meander bend flume (inlet at 0°) with a fixed point bar and pool equilibrium bed but no j‐hooks, and then used the CFD to simulate changes to flow initiated by bank‐attached boulder j‐hooks (1st attached at 70°, then a 2nd at 160°). At bankfull and half bankfull flow the j‐hooks flattened transverse water surface slopes, formed backwater pools upstream of the boulders, and steepened longitudinal water slopes across the boulders and in the conveyance region off the mid‐channel boulder tip. Streamwise velocity and mass transport jets upstream of the j‐hooks were stilled, mid‐channel jets were initiated in the conveyance region, eddies with a cross‐channel axis formed below boulders, and eddies with a vertical axis were shed into wake zones downstream of the point bar and outer bank boulders. At half bankfull depth conveyance region flow cut toward the outer bank downstream of the j‐hook boulders and the secondary circulation cells were reshaped. At bankfull depth the j‐hook at 160° was needed to redirect bank‐impinging flow sent by the upstream j‐hook. The hooked boulder tip of both j‐hooks funneled surface flow into mid‐channel plunging jets, which reversed the secondary circulation cells and initiated 1 to 3 counter rotating cells through the entire meander. The main outer bank collision zone centered at 50° without the j‐hook was moved by the j‐hook to within and just beyond the 70° j‐hook boulder region, which displaced other mass transport zones downstream. J‐hooks re‐organized water surface slopes, streamwise and cross‐channel velocities, and mass transport patterns, to move shear stress from the outer bank and into the conveyance and mid‐channel zones at bankfull flow. At half bankfull flows a patch of high shear re‐attached to the outer bank below the downstream j‐hook. J‐hook geometry and placement within natural meanders can be analyzed with CFD models to help restoration teams reach design goals and understand hydraulic impacts. Copyright © 2011 John Wiley & Sons, Ltd. 相似文献
7.
Channel curvature produces secondary currents and a transverse sloping channel bed, along which the depth increases towards the outer bank. As a result deep pools tend to form adjacent to the outer bank, promoting bank collapse. The interaction of sediment grains with the primary and secondary flow and the transverse sloping bed also causes meanders to move different grain sizes in different proportions and directions, resulting in a consistent sorting pattern. Several models have been developed to describe this process, but they all have the potential to over‐predict pool depth because they cannot account for the influence of erodible banks. In reality, bank collapse might lead to the development of a wider, shallower cross‐section and any resulting flow depth discrepancy can bias associated predictions of flow, sediment transport, and grain‐size sorting. While bed topography, sediment transport and grain sorting in bends will partly be controlled by the sedimentary characteristics of the bank materials, the magnitude of this effect has not previously been explored. This paper reports the development of a model of flow, sediment transport, grain‐size sorting, and bed topography for river bends with erodible banks. The model is tested via intercomparison of predicted and observed bed topography in one low‐energy (5·3 W m?2 specific stream power) and one high‐energy (43·4 W m?2) study reach, namely the River South Esk in Scotland and Goodwin Creek in Mississippi, respectively. Model predictions of bed topography are found to be satisfactory, at least close to the apices of bends. Finally, the model is used in sensitivity analyses that provide insight into the influence of bank erodibility on equilibrium meander morphology and associated patterns of grain‐size sorting. The sensitivity of meander response to bank cohesion is found to increase as a function of the available stream power within the two study bends. Copyright © 2002 John Wiley & Sons, Ltd. 相似文献
8.
The effects of ice cover on flow characteristics in meandering rivers are still not completely understood. Here, we quantify the effects of ice cover on flow velocity, the vertical and spatial flow distribution, and helical flow structure. Comparison with open‐channel low flow conditions is performed. An acoustic doppler current profiler (ADCP) is used to measure flow from up to three meander bends, depending on the year, in a small sandy meandering subarctic river (Pulmanki River) during two consecutive ice‐covered winters (2014 and 2015). Under ice, flow velocities and discharges were predominantly slower than during the preceding autumn open‐channel conditions. Velocity distribution was almost opposite to theoretical expectations. Under ice, velocities reduced when entering deeper water downstream of the apex in each meander bend. When entering the next bend, velocities increased again together with the shallower depths. The surface velocities were predominantly greater than bottom/riverbed velocities during open‐channel flow. The situation was the opposite in ice‐covered conditions, and the maximum velocities occurred in the middle layers of the water columns. High‐velocity core (HVC) locations varied under ice between consecutive cross‐sections. Whereas in ice‐free conditions the HVC was located next to the inner bank at the upstream cross‐sections, the HVC moved towards the outer bank around the apex and again followed the thalweg in the downstream cross‐sections. Two stacked counter‐rotating helical flow cells occurred under ice around the apex of symmetric and asymmetric bends: next to the outer bank, top‐ and bottom‐layer flows were towards the opposite direction to the middle layer flow. In the following winter, no clear counter‐rotating helical flow cells occurred due to the shallower depths and frictional disturbance by the ice cover. Most probably the flow depth was a limiting factor for the ice‐covered helical flow circulation, similarly, the shallow depths hinder secondary flow in open‐channel conditions. Copyright © 2016 John Wiley & Sons, Ltd. 相似文献
9.
The erosion of composite river banks is a complex process involving a number of factors including fluvial erosion, seepage erosion, and cantilever mass failure. To predict the rate of bank erosion with these complexities, a stochastic bank erosion model is suitable to define the probability distribution of the controlling variables. In this study, a bank erosion model in a river bend is developed by coupling several bank erosion processes with an existing hydrodynamic and morphological model. The soil erodibility of cohesive bank layers was measured using a submerged jet test apparatus. Seasonal bank erosion rates for four consecutive years at a bend in the Brahmaputra River, India, were measured by repeated bankline surveys. The ability of the model to predict erosion was evaluated in the river bend that displayed active bank erosion. In this study, different monsoon conditions and the distribution functions of two variables were considered in estimating the stochastic bank erosion rate: the probability of the soil erodibility and stochastic stage hydrographs for the nth return period river stage. Additionally, the influences of the deflection angle of the streamflow, longitudinal slope of river channel, and bed material size on bank erosion rate were also investigated. The obtained stochastic erosion predictions were compared with the observed distribution of the annual‐average bank erosion rate of 45 river bends in the Brahmaputra River. The developed model appropriately predicted the short‐term morphological dynamics of sand‐bed river bends with composite banks. Copyright © 2014 John Wiley & Sons, Ltd. 相似文献
10.
The braided Jamuna River frequently changes its courses.Sometimes the secondary channel in a braided river acts as a single thread meandering channel.In the present study an attempt has been made to investigate the flow patterns and to estimate the rate of bank erosion in a bend along the Jamuna River.The three dimensional(3D) flow velocities were measured using Acoustic Doppler Current Profiler(ADCP).It is found that the near bank velocity is amplified by 1.1 to 1.3 times as compared with the section averaged velocity.A dominant secondary current is found in the upstream bend.The evolution as well as decay of the secondary current is not as clear as it is found in the laboratory experiments.It is revealed from the analysis of the flow process that the causes of higher rate of erosion at the study bend are the oblique flow near bankline,six times amplified shear velocity than critical shear velocity near bankline and the secondary current which acts as a sediment transporting agent from the outer bank towards the inner bank or the sand bar.Based on the flow processes,a simplified erosion prediction model is developed and applied to estimate the rate of erosion at a selected bend.Finally the predicted results have been compared with the observed data at the bend and all the available data at other bends along the Jamuna River. 相似文献
11.
A depth‐averaged linearized meander evolution model was calibrated and tested using the field data collected at the Quinn River in the Black Rock Desert, Nevada. Two approaches used to test the model were: (1) simulating meander evolution and comparing the results with the observed 38 year migration pattern; and (2) fitting the model parameters to present bank asymmetry (the ratio of the maximum bank gradients on opposite sides of the channel). The data required as input were collected in the field during a high flow in May 2011 and from aerial photographs and LiDAR data. Both approaches yielded similar results for the best fit parameter values. The bank asymmetry analysis showed that the bank asymmetry and the velocity perturbation have high correlation at close to zero spatial lag while the maximum correlation between the bank asymmetry and maximum bend curvature is offset by about 25 m. The model sufficiently replicated 38 years of channel migration, with a few locations significantly under‐ or over‐predicted. Inadequacies of the flow model and/or variation in bank properties unaccounted for are most likely the causes for these discrepancies. Flow through the Quinn River was also simulated by a more general 3D model. The downstream pattern of near‐bank shear stresses simulated by the 3D model is nearly identical to those resulting from the linearized flow model. Topographic profiles across interior bends are essentially invariant over a wide range of migration rates, suggesting that the traditional formulation that cut bank erosion processes govern migration rates is appropriate for the Quinn River. Copyright © 2014 John Wiley & Sons, Ltd. 相似文献
12.
Channel morphologic processes of a highly sinuous bend approaching neck cutoff by bank erosion in the middle Yangtze River 总被引：2，自引：0，他引：2
Zhiwei Li Hanyuan Yang Junqiang Xia Meirong Zhou Shanshan Deng Yingzhen Wang 《国际泥沙研究》2021,36(4):457-467
The distal reach of the Lower Jingjiang River(LJR)in the middle of the Yangtze River consists of five adjacent bends,among which the Qigongling Bend is a U-shaped meander with a mean sinuosity of 2.2 and the narrowest neck 525 m in width.This bend is slowly approaching neck cutoff owing to progressive bank erosion.An abnormal phenomenon has occurred in this bend since the Three Gorges Reservoir(TGR)began to operate in 2003 which is erosion in the inner bank zone and deposition in the outer bank zone.This problem has not been fully understood because of the interplay of changes in water-sediment,bank erosion,and artificial bank revetment.In this study,aerial and remote sensing images,hydrological data,channel topography,and an existing bank erosion model are used to reveal channel morphodynamics of this bend and the trend of the potential neck cutoff induced by bank erosion.The study results show that the clear water released from the TGR has provided by forcefully eroded the point bar of inner bank but failed to scour the outer bank due to the protection of bank revetment since the 1990 s.Thus far,the outer bank zone near the bend apex has increasingly widened in conjunction with the formation of 2 emerging sand bars.Consequently,the thalweg of the main channel has laterally shifted toward the inner bank by roughly 800 m.More severely,the rate of bank retreat on the upstream side of the bend neck was about 4.5 m/yr in 2010-2019,but the downstream side of this neck was experienced slight deposition.Bank erosion could be accelerated by progressively increasing erosion and eventually trigger the occurrence of neck cutoff in the next few decades,thereby significantly altering the quasi-equilibrium regime of channel morphodynamics in the LJR. 相似文献
13.
Experimental results of the mean flow field and turbulence characteristics for flow in a model channel bend with a mobile sand bed are presented. Acoustic Doppler velocimeters (ADVs) were used to measure the three components of instantaneous velocities at multiple cross sections in a 135° channel bend for two separate experiments at different stages of clear water scour conditions. With measurements at multiple cross sections through the bend it was possible to map the changes in both the spatial distribution of the mean velocity field and the three Reynolds shear stresses. Turbulent stresses are known to contribute to sediment transport and the three‐dimensionality inherent to flow in open channel bends presents a useful case for determining specific relations between three‐dimensional turbulence and sediment entrainment and transport. These measurements will also provide the necessary data for validating numerical simulations of turbulent flow and sediment transport. The results show that the magnitude and distribution of three‐dimensional Reynolds stresses increase through the bend, with streamwise‐cross stream and cross stream‐vertical components exceeding the maximum principal Reynolds stress through the bend. The most intriguing observation is that near‐bed maximum positive streamwise‐cross stream Reynolds stress coincides with the leading edge of the outer bank scour hole (or thalweg), while maximum cross stream‐vertical Reynolds stress (in combination with high negative streamwise‐cross stream Reynolds stress near the bend apex) coincides with the leading edge of the inner bank bar. Maximum Reynolds stress and average turbulent kinetic energy appear to be greater and more localized over the scour hole before final equilibrium scour is reached. This suggests that the turbulent energy in the flow is higher while the channel bed is developing, and both lower turbulent energy and a broader distribution of turbulent stresses near the bed are required for cessation of particle mobilization and transport. Copyright © 2010 John Wiley & Sons, Ltd. 相似文献
14.
Flow in meandering bends is characterized by the formation of a large cross‐sectional central‐region circulation cell. The width‐to‐depth ratio is one of the most important parameters affecting the entity of the cross‐circulation motion. In steep outside bends, beside the central‐region cell, a counter‐rotating circulation cell often forms in the upper part of the outer‐bank. In spite of its practical importance, the evolving mechanisms of both the circulation cells and their role on boundary shear stress distribution in bends are not yet fully understood. The aim of the present paper is to gain some insight into how cross‐sectional flow motion evolves along meandering bends. Experiments have been carried out in a laboratory meandering channel of large amplitude, over a deformed‐rigid bed, for two values of the width‐to‐depth ratio. The three‐dimensional flow velocity field has been measured in detail at five cross‐sections, almost equally spaced along the channel reach between two consecutive apex sections. The measurements have been carried out on a fine grid by an acoustic Doppler velocity profiler. The distributions of the cross‐sectional flow (e.g. cross‐sectional flow velocity, net transversal flux) and turbulent kinetic energy are analyzed in each investigated section. Measurements show that the counter‐rotating circulation cell is evident only in the case of ‘small’ width‐to‐depth ratio. Such circulation cell begins at the bend entrance and it is fully developed at the bend apex; then it decays. At the bend apex, the core of maximum velocity is found near the bed at about the separation between the central and the outer‐bank circulation cells. Moreover, the presence of the counter‐rotating circulation cell allows the bank shear stress to maintain low values in the outer‐side of the bend. Copyright © 2010 John Wiley & Sons, Ltd. 相似文献
15.
Channel bars and banks strongly affect the morphology of both braided and meandering rivers. Accordingly, bar formation and bank erosion processes have been greatly explored. There is, however, a lack of investigations addressing the interactions between bed and bank morphodynamics, especially over short timescales. One major implication of this gap is that the processes leading to the repeated accretion of mid‐channel bars and associated widenings remain unsolved. In a restored section of the Drau River, a gravel‐bed river in Austria, mid‐channel bars have developed in a widening channel. During mean flow conditions, the bars divert the flow towards the banks. One channel section exhibited both an actively retreating bank and an expanding mid‐channel bar, and was selected to investigate the morphodynamic processes involved in bar accretion and channel widening at the intra‐event timescale. We repeatedly surveyed riverbed and riverbank topography, monitored riverbank hydrology and mounted a time‐lapse camera for continuous observation of riverbank erosion processes during four flow events. The mid‐channel bar was shown to accrete when it was submerged during flood events, which at the subsequent flow diversion during lower discharges narrowed the branch along the bank and increased the water surface elevation upstream from the riffle, which constituted the inlet into the branch. These changes of bed topography accelerated the flow along the bank and triggered bank failures up to 20 days after the flood events. Four analysed flow events exhibited a total bar expansion from initially 126 m2 to 295 m2, while bank retreat was 6 m at the apex of the branch. The results revealed the forcing role of bar accretion in channel widening and highlighted the importance of intra‐event scale bed morphodynamics for bank erosion, which were summarized in a conceptual model of the observed bar–bank interactions. Copyright © 2015 John Wiley & Sons, Ltd. 相似文献
16.
Channelisation measures taken halfway the 20th century have had destructive consequences for the diversity of the ecology in the majority of the lowland streams in countries such as the Netherlands. Re-meandering is the common practice in restoring these lowland streams. Three reconstructed streams were monitored during the initial two years after construction of a new channel. The monitoring program included morphological surveys, sediment sampling, habitat pattern surveys, and discharge and water level measurements. Adjustments of the longitudinal bed profile formed the main morphological response. These adjustments were most likely caused by a lack of longitudinal connectivity of the streams as a whole, interrupting transport of sediment at locations of weirs and culverts. Bank erosion was observed only in a limited number of channel bends, and was often related to floodplain heterogeneity. Longitudinal channel bed adjustments and bank erosion were mainly caused by exogenous influences. In channel bends, the cross-sectional shape transformed from trapezoidal to the typical asymmetrical shape as found in meandering rivers. This behaviour can be attributed to an autogenous response to the prevailing flow conditions. Due to the prevailing fine sediment characteristics, bed material is readily set in motion and is being transported during the entire year. The existing design principles fail to address the initial morphological development after reconstruction. An evaluation of pre-set targets to realise water depth and flow velocity ranges shows the current procedures to be deficient. Based on this unfavourable evaluation, and the two-dimensional nature of habitat patterns needed to improve the conditions for stream organisms, we recommend to predict morphological developments as part of the design procedures for lowland stream restoration in the Netherlands. 相似文献
17.
Modeling of flooding events resulting from bank overflooding and levee breaching is of relevant social and environmental interest. Two-dimensional (2D) hydrodynamic models integrating the shallow water equations turn out to be very effective tools for the purpose at hand. Many of the available models also use 1D channel elements, fully coupled to the 2D model, to simulate the flow of small channels dissecting the urban and rural areas, and 1D elements, referred to as 1D-links, to efficiently model the flow over levees, road and rail embankments, bunds, the flow through control gates, either free or submerged, and the operation of other hydraulic structures. In this work we propose a physically-based 1D-link to model breach formation and evolution in fluvial levees, and levee failure due to either piping or overtopping. The proposed 1D-link is then embedded in a 1D–2D hydrodynamic model, thus accounting for critical feedbacks between breach formation and changes in the hydrodynamic flow field. The breach model also includes the possibility of simulating breach closure, an important feature particularly in the view of hydraulic risk assessment and management of the emergency. The model is applied to five different case studies and the results of the numerical simulations compare favorably with field observations displaying a good agreement in terms of urban and rural flooded areas, water levels within the channel, final breach widths, and water volumes flowed through the breach. 相似文献
18.
This paper describes the morphology, sequential development and general sedimentology of concave-bank benches on the Murrumbidgee River of southeastern Australia, and also notes their important role in floodplain formation on certain meandering rivers in western Canada. Benches form against the concave bank (cut-bank) of abruptly curving bends immediately upstream of the point of maximum curvature. As a result of flow deflection against the upstream limb of the convex bank, the channel widens here and produces a zone of expanded flow facilitating flow separation near the upstream limb of the concave bank. Sedimentation within this zone starts with a longitudinal-shaped bar of medium sand forming a platform isolated even at low flow by a narrow secondary channel against the concave bank. Aggradation of the longitudinal-shaped bar with fine sand, mud and organic matter permits the establishment of trees. Further sedimentation, particularly around the young trees, results in the formation of a fully developed bench isolated by the secondary channel from the remainder of the floodplain only during high flows. Observations on confined meandering rivers in western Canada provide evidence of substantial floodplain formation by concave-bank bench accretion, a process distinctly different in character to the more familiar mechanism of lateral point-bar accretion. Furthermore, the preservation of abundant organic debris means that extensive bench deposits may be a source of locally useful natural gas from within floodplain sediments. 相似文献
19.
Temporal and spatial adjustments of channel migration and planform geometry: responses to ENSO driven climate anomalies on the tropical freely‐meandering Aguapeí River,São Paulo,Brazil 下载免费PDF全文
下载免费PDF全文 Two reaches of Aguapeí River, a left‐bank tributary of the Paraná River in western São Paulo state, Brazil, were studied with the objective of assessing the role of bend curvature on channel migration in this wet‐tropical system and examining if land‐use changes or ENSO (El Niño Southern Oscillation) driven climate anomalies over nearly half a century have changed migration behaviour and planform geometry. Meander‐bend migration rates and morphometric parameters including meander‐bend curvature, sinuosity, meander wavelength and channel width, were measured and the frequency of bend cutoffs was analysed in order to determine the rate of change of channel adjustment over a 48 year period to 2010. Results show that maximum average channel migration rates occur in bends with curvatures of about 2–3 rc/w, similar to other previously studied temperate and subarctic freely meandering rivers although not as pronounced and with a tendency to favour tighter curvature. From 1962 to 2010 the Aguapeí River has undergone a significant reduction in sinuosity, a shift from tightly curving to more open bends, an overall decline in channel migration rates, an associated decrease in the frequency of neck‐cutoffs and an overall increase in channel width. As the majority of the drainage basin (96%) was already deforested in 1962, channel form and process changes were, unlike an interpretation for an adjacent river system, not attributed to altered land‐use but rather to a sharp ENSO‐driven increase in the magnitude of peak flow‐discharges of some 32% since 1972. In summary, this research revealed that recent climate and associated flow regime changes are having a pronounced effect on river channel behaviour in the Aguapeí River investigated here. Copyright © 2018 John Wiley & Sons, Ltd. 相似文献
20.
Rachel A. Nanson 《地球表面变化过程与地形》2010,35(2):119-135
Upland swamp channels with low width/depth ratios (w/d), armoured beds, minimal sediment loads, tightly curving bends and an absence of point bars provide a striking contrast to the flow characteristics of larger channels with higher w/d ratios. Two subsets of these bends were examined in relation to their patterns of cross‐stream flow relative to the channel boundary. The first, with mean w/d = 2·0 and gentle barforms, exhibited even velocity distributions at bend entrances but developed vertically stacked pairs of maximum velocity filaments (MVFs). Cross‐stream circulation increased with decreasing curvature before essentially ceasing in the tightest bend due to the conservation of angular momentum and reduced vertical velocity differentials; bed friction has more limited influence in narrow deep channels relative to bank friction. In the second subset of bends, with larger w/d (mean 4·8) and much steeper barforms, the MVFs were laterally paired and strongly helical flow was partly driven by the vertical confinement of flow due to large, stable barforms at the bend entrances. In one bend, the velocity profile became inverted immediately past the apex and caused helical flow to abruptly reverse. Point bars in relatively wide bedload channels appear to greatly distort secondary flow patterns. In narrow, deep, sediment‐starved channels, separation zones against the convex and/or the concave bank deliver the flow confinement that would otherwise be provided by point bars or concave‐bank benches. In these channels, separation zones are important for protecting both the channel bed and banks from scour. Three‐dimensional near bankfull flow fields are presented for one bend with a meander pool; inward shifting of the MVF and limited sediment supply are proposed as mechanisms for the development and maintenance of these features. These flow data in narrow and deep peatland channels demonstrate very different flow patterns and morphological characteristics relative to the more commonly studied wide, shallow channels with more abundant sediment. Copyright © 2009 John Wiley & Sons, Ltd. 相似文献