共查询到20条相似文献，搜索用时 171 毫秒
1.
因其特殊的地质成因,柱状节理成为一种具有强烈非连续性及各向异性的特殊岩体结构。以白鹤滩水电工程设计、建设中所遇到的柱状节理玄武岩体为背景,针对柱状节理岩体的等效变形模量问题,在探讨了其结构效应表征参数的基础上,利用节理网络有限元为工具,研究各结构效应表征参数对柱状节理岩体等效变形模量的影响。研究结果表明：在柱轴线横向平面上,对于柱体不规则程度,当柱体完全不规则相对于完全规则情况,等效模量提高大约10%左右;在其他条件不变情况下,当柱体平均边长从0.1 m增加至0.5 m时,等效模量从5.36 GPa增加至23.4 GPa;对不同加载方向的研究结果表明,柱状节理在柱轴横向平面上可以视作各向同性;当节理刚度线性递增时,相应的岩体等效模量也基本符合线性递增的规律。在平行柱体轴线平面,节理组2间距越大,柱状节理岩体的等效变形模量越大;随着错距比的增加,柱状节理岩体的等效变形模量呈现先增加后减少的趋势,当错距比为50%时,节理岩体的等效变形模量取最大值;对于节理刚度的影响,与柱轴横向平面类似的,随柱体轴线平面上节理刚度的线性增加,相应的岩体模量也基本符合线性递增的规律。该研究成果与已有的现场研究成果及三维数值模型成果相比,吻合良好。说明了文中提供的研究结论具有较好的可信度及参考价值。 相似文献
2.
柱状节理岩体的复杂结构使其现场力学参数的确定存在困难,可靠地估计柱状节理岩体强度及变形特性对工程安全至关重要。结合Voronoi图形及3D打印技术制作不规则柱状节理岩体光敏树脂模具,并制备了具有不同倾角的规则及不规则柱状节理岩体试样。基于开展的单轴压缩试验结果,分析不同截面柱状节理岩体的变形及强度特性差异。根据试样最终破坏形态,揭示柱状节理岩体破坏模式及机制。结合已有研究结果,描述节理面材料对柱状节理岩体破坏形态及强度的影响。基于传统节理系数方法,提出了更能反映柱状节理岩体柱体结构特征的修正节理系数方法。采用修正节理系数法建立规则及不规则柱状节理岩体试验结果与现场变形及强度参数间的经验关系,将所提出计算公式应用于白鹤滩水电站工程,预测结果与现场实测值及RMR法（RMR为岩石质量评分指标）、Q法（Q为岩体质量指标）的预测值进行比较。结果表明,对于现场变形和强度参数,所提出的修正节理系数法的预测结果与现场实测结果较为吻合。 相似文献
3.
Hoek-Brown准则在岩质边坡稳定分析中的优越性 总被引：1，自引：0，他引：1
介绍了最新的用于估计完整岩石或节理岩体剪切强度的半经验准则Hoek-Brown屈服准则。结合岩质边坡工程并基于强度折减法计算边坡安全系数,与等效Mohr-Coulomb屈服准则数值模拟对比,得出Hoek-Brown屈服准则采用基于应力水平的塑性流动法则,考虑了岩体结构、岩块强度、应力状态等多种因素的影响,能很好地反映岩体的非线性破坏特征及机理,符合节理岩体的变形和破坏特点。 相似文献
4.
岩体在加载和卸荷条件下,其力学性质有本质的区别。采用数值模拟方法,以ADINA软件为计算平台,研究了卸荷条件下,锚固密度、锚杆长度和岩体性质3个因素对节理岩体力学参数的影响。采用等效变形参数的方法计算节理岩体和锚固体的等效变形模量和泊松比。在分析数值计算结果的基础上,分析了加锚后等效变形模量En与锚固密度N和锚杆长度L之间的关系。 相似文献
5.
基于现场试验的岩体变形模量尺寸效应研究 总被引：6，自引：4，他引：2
岩体力学参数具有随机性和不确定性,合理确定岩体力学参数是岩土工程稳定性分析的基础和关键。以某水电站前期研究的110个钻孔弹模测试数据为研究样本,对其进行了统计特征分析,确定变形模量的概率分布特征更符合Weibull分布。以钻孔弹模仪承压板尺寸为岩体变形模量研究的样本尺度,岩体由该尺度的岩样叠加而成,建立了不同尺寸的立方体岩体数值分析模型,按照Weibull分布随机给出各岩样的变形模量,在此基础上对不同尺寸的岩体分别进行5 000次单轴压缩试验的数值模拟,得到了不同尺度岩体等效变形模量的变化特征,确定了岩体等效变形模量的REV。基于现场实测岩体变形模量与概率统计理论相结合研究岩体变形模量是一个新的尝试,可为该水电站工程岩体力学参数的合理取值提供依据。 相似文献
6.
基于遍布节理模型的边坡稳定性强度折减法分析 总被引：10，自引：4，他引：6
采用非线性数值分析方法分析边坡稳定性问题时,强度折减法因其具有较多的优点而得到广泛应用。岩土体一般采用理想弹塑性模型,屈服准则为广义米赛斯准则。对于密集节理岩质边坡稳定性问题,采用遍布节理模型可同时考虑岩块和节理属性,更符合岩体状态及工程实际,认为岩体经强度折减后潜在破坏可能首先出现在岩体中或沿节理面或二者同时破坏。结合工程实例,基于遍布节理模型的强度折减法计算结果表明,潜在滑移面为折线型滑面,下部潜在滑移面倾角与节理面等效内摩擦角基本一致,上部潜在滑移面与岩体拉破坏相关;节理倾角与边坡安全系数、潜在滑动范围密切相关,陡倾角节理对边坡稳定性影响较小。通过对边坡失稳判据和边坡滑移面确定的探讨,认为以力或位移不收敛作为边坡失稳判据是适当的,而边坡的剪应变速率物理意义十分明确,适于作为边坡潜在滑移面的确定依据。 相似文献
7.
锚固节理岩体等效力学参数三维离散元模拟 总被引：4，自引：0，他引：4
节理岩体是工程边坡的重要研究对象,通过数值模拟（3DEC）的方法研究了加锚节理岩体的力学特性。以龙滩水电站左岸边坡的锚固设计为例,推导了边坡加锚节理岩体的等效力学参数,进行了岩石数值单轴压缩试验、直剪试验以及岩体结构面直剪试验,对数值试验的结果进行了误差分析和修正,确定出加锚节理岩体的等效力学参数为：岩石的变形模量、内摩擦角、内聚力不变,结构面的内摩擦角不变,内聚力由50 kPa提高到122 kPa。所得结论与采用物理试验的试验结果相符,验证了用数值模拟方法进行岩石力学试验的可行性和可靠性。 相似文献
8.
《岩土力学》2020,(Z1)
经验公式估算岩体变形模量是岩体工程中常用方法之一,在岩体分级系统中出现了很多的经验估算公式,但对于不同经验估算公式计算结果的统计特征与自变量权重分析报道较少。采用蒙特卡罗随机抽样法,基于地质强度指标GSI(geological strength index)系统地分析岩体变形模量估算公式计算结果的统计分布特征及其自变量的权重,讨论不同扰动因子条件下的岩体变形模量统计分布规律及其自变量权重的变化规律。结果表明,扰动因子对各种岩体变形模量统计分布模型均值的影响各异,对Hoek公式得出的岩体变形模量统计模型均值的影响最大,质量好的岩体变形模量受到的影响比质量差的岩体小。 相似文献
9.
坝基软弱破碎地质体是影响大坝安全的关键因素之一,其岩体力学参数的合理确定是大坝工程稳定分析与安全评价的基础。为合理确定向家坝水电工程左岸坝基挤压破碎带的变形模量,进行了室内MTS变形模量试验、现场小型承压板和大型承压板试验研究。3种试验方法得到的破碎带岩体变形模量基本都小于1.0 GPa,有盖层承压板试验条件下的破碎岩体变形模量测试值远大于无盖层岩体影响情况下的试验成果。研究成果表明,不同试验方法反映了左岸坝基破碎带岩体的不同受力状态,其变形模量也呈现一定差异性。在分析挤压破碎带变形模量试验值差异性的原因基础上,提出了左岸坝基破碎带岩体变形模量的建议值。 相似文献
10.
节理对卸荷条件下岩体的力学性质有重要影响。通过含2条不同间距预制断续节理岩体的三轴卸荷破坏试验,研究了节理岩体在卸荷应力条件下的应力-应变特征、强度、变形特征、破坏规律及节理间距对岩体力学性质的影响。研究表明：相比于完整岩体,节理岩体卸荷破坏时从峰值强度跌落至残余强度过程中轴向应变较大,为完整岩体的3～4倍,岩体破坏时极限强度明显低于完整岩体,脆性特征不如完整岩体明显;节理岩体卸荷破坏时,变形模量有较大幅度的降低,其降低程度是同条件下完整岩体的6～7倍,节理间距越大,变形模量降低程度越大;与含预制节理岩样三轴加载试验结果相比,节理岩体卸荷条件下破坏程度更为强烈,除剪切破裂面外,沿最大主应力方向分布的不同级别的张性裂隙非常发育,预制节理的间距对岩体破坏形态影响不大。 相似文献
11.
工程岩体强度的估算方法 总被引：1，自引：0，他引：1
岩体是由地质过程中形成的岩块和结构面网络组成。由于试件制备、加荷等均极困难,且昂贵而费时,难于像岩块那样进行大量试验来确定岩体之强度。所以,如何通过室内小试件试验来估算大岩体的强度成为工程地质工作者所关注的问题。本文介绍了两种用小试件资料估算大岩体强度的方法及计算实例。 相似文献
12.
A 3D model of a jointed rock mass and its deformation properties 总被引：1，自引：0，他引：1
Faquan Wu 《Geotechnical and Geological Engineering》1988,6(2):169-176
Conclusion A geometric model of a jointed rock mass and some formulae of strain and deformation parametersE, G and were given. They may be useful for evaluating the deformation parameters of rock masses and classifying the rock mass quatitatively. 相似文献
13.
Modeling strategy for jointed rock masses reinforced by rock bolts in tunneling practice 总被引：2，自引：1，他引：1
Shunsuke Sakurai 《Acta Geotechnica》2010,5(2):121-126
This paper deals with the modeling of jointed rock masses reinforced by rock bolts. It is well known that rock bolts are extremely
effective in reinforcing jointed rocks. However, if a continuum approach is adopted for modeling jointed rock masses, it is
often misleading to evaluate the effectiveness of the rock bolts by numerical analyses such as the finite element method.
This may be due to the fact that since no more joints exist in the continuum, the effectiveness of the rock bolts in constraining
the relative displacements along the joints cannot be evaluated properly. In order to investigate the reinforcement effect
of rock bolts, physical model tests were performed in the laboratory. The test results revealed that jointed rock masses should
be modeled as an equivalent continuum after the installation of rock bolts and that the mechanical parameters of the equivalent
continuum should be evaluated by considering the reinforcement effect of the rock bolts. Therefore, the values of the mechanical
parameters differ from place to place in accordance with the relation between joint orientation and rock bolt direction, even
though joint systems are homogeneous. In conclusion, in the continuum approach for modeling jointed rock masses, it should
be emphasized that rock bolts and jointed rock masses should not be modeled separately but should be modeled simultaneously
by considering the reinforcement effect of the rock bolts in constraining joint movement. The modeling of shotcrete reinforced
by steel ribs is also discussed in comparison to the modeling by rock bolts. 相似文献
14.
Deformability of rock masses influencing their behavior is an important geomechanical property for the design of rock structures. Due to the difficulties in determining the deformability of jointed rock masses at the laboratory-scale, various in-situ test methods such as pressuremeter, dilatometer, plate loading tests etc. have been developed. Although these techniques are currently the best and direct methods, they are time-consuming and expensive, and present operational difficulties. In addition, the influence of the test volume on deformation modulus depending on the method employed is also important. For these reasons empirical equations to indirectly estimate the deformation modulus have also been recommended by several investigators as an alternative approach. In this study; the geomechanical quality of weak, heavily jointed, sheared and/or blocky greywacke rock masses, on which very concentrated civil works are continuing at the southern and southwestern parts of Ankara (Turkey), was assessed. The deformation modulus was determined by pressuremeter tests, the possible effects of variables on the derived deformation modulus from the pressuremeter test were evaluated by numerical methods, and the comparisons between the deformation modulus of the greywackes obtained from the pressuremeter tests and their geomechanical quality (GSI and RMR) were made. Numerical simulations revealed that the presence of a disturbed annulus around the borehole causes underestimation of the deformation modulus, while the effect of length to diameter ratio of the pressuremeter probe on the deformation modulus is minor. Based on the geo-engineering characterization assessments, mainly two greywacke rock masses with different geomechanical qualities were identified. Geotechnical quality of one of these rock masses was verified by the back analysis of two slope failures. The empirical equations to indirectly estimate the deformation modulus of the greywackes using their GSI and RMR values yielded high coefficients of correlation. 相似文献
15.
节理岩体三维偶应力弹性理论 总被引：7，自引：3，他引：7
节理的存在使得岩体的力学特性十分复杂。偶应力理论考虑了介质内颗粒尺度的影响，它以具有一定尺度的微元体为研究对象，引进了偶应力及弯曲曲率的概念，从而考虑了弯曲效应对介质变形特性的影响，可以用来解决岩土工程中的地下洞室底鼓、顶板开裂及反倾向层状岩体的弯曲倾倒等弯曲变形及弯曲破坏问题。本文考虑了节理间距的影响，对节理岩体的空间间题提出了弹性偶应力理论并建立了有限元计算模式，最后通过算例说明用偶应力理论解决上述问题的有效性。 相似文献
16.
节理化块体边坡失稳机理数值分析 总被引：3，自引：1，他引：3
针对三峡库区移民新址的工程地质问题，用改进的岩土工程软件系统FINAL，研究了节理化块体岩坡的失稳机理，指出除了节理的C，值控制岩块的滑移、倾覆变形，倾倒等破坏形式外，岩块的模量E也对倾覆变形破坏起重要作用，从而不仅说明了保护坡脚，防止岩块浸水软化的必要性，也说明了应用传统离散元法分析这类问题的局限性。 相似文献
17.
Estimating the Strength of Jointed Rock Masses 总被引：1，自引：0，他引：1
Lianyang Zhang 《Rock Mechanics and Rock Engineering》2010,43(4):391-402
Determination of the strength of jointed rock masses is an important and challenging task in rock mechanics and rock engineering.
In this article, the existing empirical methods for estimating the unconfined compressive strength of jointed rock masses
are reviewed and evaluated, including the jointing index methods, the joint factor methods, and the methods based on rock
mass classification. The review shows that different empirical methods may produce very different estimates. Since in many
cases, rock quality designation (RQD) is the only information available for describing rock discontinuities, a new empirical
relation is developed for estimating rock mass strength based on RQD. The newly developed empirical relation is applied to
estimate the unconfined compressive strength of rock masses at six sites and the results are compared with those from the
empirical methods based on rock mass classification. The estimated unconfined compressive strength values from the new empirical
relation are essentially in the middle of the estimated values from the different empirical methods based on rock mass classification.
Similar to the existing empirical methods, the newly developed relation is only approximate and should be used, with care,
only for a first estimate of the unconfined compressive strength of rock masses. Recommendations are provided on how to apply
the newly developed relation in combination with the existing empirical methods for estimating rock mass strength in practice. 相似文献
18.
An anisotropic geomechanical model for jointed rock mass is presented. Simultaneously with deriving the orthotropic anisotropy elastic parameters along the positive axis, the equivalent compliance matrix for the deflection axis orthotropic anisotropy was derived through a three-dimensional coordinate transformation. In addition, Singh’s analysis of the stress concentration effects of intermittent joints was adopted, based on two groups of intermittent joints and a set of cross-cutting joints in the jointed rock mass. The stress concentration effects caused by intermittent joints and the coupling effect of cross-cutting joints along the deflection-axis are also considered. The proposed anisotropic mechanics parameters method is applied to determine the deformation parameters of jointed granite at the Taishan Nuclear Power Station. Combined with the deterministic mechanical parameters of rock blocks and joints, the deformation parameters and their variability in jointed rock masses are estimated quantitatively. The computed results show that jointed granite at the Taishan Nuclear Power Station exhibits typical anisotropic mechanical characteristics; the elastic moduli in the two horizontal directions were similar, but the elastic modulus in the vertical direction was much greater. Jointed rock elastic moduli in the two horizontal and vertical directions were respectively about 24% and 37% of the core of rock, showing weakly orthotropic anisotropy; the ratio of elastic moduli in the vertical and horizontal directions was 1.53, clearly indicating the transversely isotropic rock mass mechanical characteristics. The method can be popularized to solve other rock mechanics problems in nuclear power engineering. 相似文献
19.
The high computational costs associated with the implicit formulation of discontinuous deformation analysis (DDA) have been one of the major obstacles for its implementation to engineering problems involving jointed rock masses with large numbers of blocks. In this paper, the Newmark-based predictor-corrector solution (NPC) approach was modified to improve the performance of the original DDA solution module in modeling discontinuous problems. The equation of motion for a discrete block system is first established with emphasis on the consideration of contact constraints. A family of modified Newmark-based predictor-corrector integration (MNPC) scheme is then proposed and implemented into a unified analysis framework. Comparisons are made between the proposed approach and the widely used constant acceleration (CA) integration approach and central difference (CD) approach, regarding the stability and numerical damping features for a single-degree-of-freedom model, where the implications of the proposed approach on open-close iteration are also discussed. The validity of the proposed approach is verified by several benchmarking examples, and it is then applied to two typical problems with different numbers of blocks. The results show that the original CA approach in DDA is efficient for the simulation of quasi-static deformation of jointed rock masses, while the proposed MNPC approach leads to improved computational efficiency for dynamic analysis of large-scale jointed rock masses. The MNPC approach therefore provides an additional option for efficient DDA of jointed rock masses. 相似文献
20.
为了保障岩土工程结构能长期正常使用,需要对其蠕变变形进行分析。“时步-初应变”法是一种常用的计算岩石蠕变的方法。数值流形方法是一种新兴的数值计算方法,常用于计算节理岩体的变形,但尚未被试用于计算蠕变变形。在原数值流形方法的程序中增加了基于“时步-初应变”法的计算模块,通过对广义开尔文模型进行的模拟,显示新程序可以正确反映岩石的黏弹性蠕变趋势,并能够计算包含节理的岩体的蠕变变形,改进后的数值流形方法不但能够模拟岩石的线弹性变形,而且可以模拟岩石的黏弹性蠕变,比原流形方法更能全面地模拟岩石的变形,扩展了数值流形方法在岩土工程中的使用范围。 相似文献