首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献，搜索用时 609 毫秒
1.
Aeolian (wind) erosion is most common in arid regions. The resulted emission of PM10 (particulate matter that is smaller than 10 μm in diameter) from the soil has many environmental and socioeconomic consequences such as soil degradation and air pollution. Topsoil resistance to aeolian transport highly depends on the surface composition. The study aim was to examine variations in PM10 fluxes in a desert-dust source due to surface composition and topsoil disturbance. Aeolian field experiments using a boundary layer wind tunnel alongside soil composition analysis were integrated in this study. The results show variations in PM10 fluxes (ranging from 9.5 to 524.6 mg m?2 min?1) in the studied area. Higher wind velocity increased significantly the PM10 fluxes in all surface compositions. A short-term natural disturbance caused changes in the aggregate soil distribution (ASD) and increased significantly PM10 emissions. Considering that PM10 contains clays, organic matter, and absorbed elements, the recorded PM10 fluxes are indicative of the potential soil loss and degradation by wind erosion in such resource-limited ecosystems. The findings have implications in modeling dust emission from a source area with complex surfaces.  相似文献   

2.
The rapid urbanization, industrialization, modernization, and the frequent Middle Eastern dust storms have negatively impacted the ambient air quality in Bahrain. The objective of this study is to identify the most critical atmospheric air pollutants with emphasis on their potential risk to health based on calculated AQI (air quality index) values using EPA approach. The air quality datasets of particulate matters (PM10 and PM2.5), ozone (O3), sulfur dioxide (SO2), nitrogen dioxide (NO2), and carbon monoxide (CO) were measured in January 2012 and August 2012 using five mobile air quality monitoring stations located at different governorates. The results of this study demonstrated that PM10 and PM2.5 are the most critical air pollutants in Bahrain with PM2.5 prevailing during January 2012 and PM10 prevailing during August 2012. The corresponding AQI categories were utilized to evaluate spatial variability of particulate matters in five governorates. The impact of meteorological factors such as ambient air temperature, wind speed, relative humidity, and total precipitation on ambient air quality were discussed. The analysis demonstrated that the highest PM10 concentrations were observed in the Northern Governorate while the highest PM2.5 concentrations were observed in the Capital, Central, and Northern Governorates during August 2012. It was observed that the levels of PM2.5 pollution were higher within proximity of the industrial zone. The results suggested that the average PM2.5/PM10 ratio in August 2012 was lower than in January 2012 due to the Aeolian processes. This study concludes that higher wind speed, total precipitation, relative humidity rates, and lower ambient air temperature in January 2012 assisted with the dissipation of particulate matter thus lowering the pollution levels of both PM10 and PM2.5 in comparison to August 2012.  相似文献   

3.
Arid and semi‐arid environments are important sources for the atmospheric loading of PM10 (particulate matter <10 μm), although the emission of this material is often limited by surface crusts. This study investigates the emission and vertical flux of PM10 from a clay‐crusted playa, with and without saltating grains to abrade the surface. Using a portable field wind tunnel, it was found that, despite disturbance to the surface, the emission of PM10 decays rapidly without abrasion. Only in the presence of saltating grains was PM10 continuously liberated from the surface, such that the emission rate (the total amount of PM10 emitted from the surface expressed as a horizontal flux) varied linearly with the saltation transport rate. Although the emission of PM10 was found to depend on saltation abrasion, past studies have tended to focus on the relationship between the vertical flux of PM10 (the amount of PM10 being transported vertically through the boundary layer) and the shear velocity. In this study, the vertical flux of PM10 was found to vary with the shear velocity to the power of 2·14. Although the vertical PM10 flux is a proportion of the emission rate (the horizontal flux), no statistically significant relationship was observed between the emission rate and the shear velocity. The disparity of these results is explained by the lack of a consistent relationship between the shear velocity and the saltation transport rate in this supply‐limited environment. This suggests that the observed relationship between the vertical PM10 flux and the shear velocity is a spurious correlation, resulting from the use of shear velocity to calculate the vertical dust flux. It is thus concluded that shear velocity is not an appropriate variable for emission modelling in supply‐limited environments and that improvements in dust emission modelling will only be realized if the abrasion process is the focus of a concerted research effort.  相似文献   

4.
The respirable particle matter (PM10) concentration in urban areas has been a chronic cause concern and principal reason for increased morbidity rate among resident population. The present study aimed at estimating a discrete event like mortality rate associated and attributable to excess particulate matter pollution in the Kathmandu Valley area. The Government of Nepal conducts air monitoring of particulates at its air monitoring site network covering valley area. Adopting the data available with respect to PM10 and with several other considerations like cutoff value for PM10, mean annual concentration, demographic data of valley, exceedance to the reference cutoff value, attributable fraction evolution and computation relative risk attributable to PM10 was computed. Assumption was made about the relative risk of long-term average PM10 exposure on natural mortality estimated and reported from a previous study. The estimation or mortality rate in our case was 0.95% after all these considerations and computation. This implies that 95 deaths out of 10,000 deaths are due to particulate pollution existing in the Kathmandu Valley Area.  相似文献   

5.
Eight selected heavy metals and phosphorus (Fe, Zn, Pb, Cu, Cr, Cd, Ni and P) were analyzed in the dust fall samples collected from the surrounding areas adjacent to Al-Hisa phosphate mine central Jordan during summer 2008. The chemical analysis was done using the ICP-AES, after being digested with (HNO3/HCl/HF) acid mixture, beside the identification of their mineral constituents using the XRD. Moreover, the particulate matter (PM) size was investigated and divided into four fractions (PM2.5, PM2.5–10, PMC10–100 and PM>100). The PM10–PM100 were found to be the most abundant in the local atmosphere followed by PM2.5–PM10, while the respirable fraction (PM2.5) and giant fraction (PM>100) showed lower levels. The studied samples contain less PM2.5 and PM10 particulates (9.39 and 28.67), respectively, than samples located far from the mine area (blank samples) (17.32 and 51.7) for PM2.5 and PM10, respectively. The meteorological effects, mainly the prevailing wind direction beside the distance to emission sources affect the distribution of dust particle sizes. Heavy metal contents in studied samples are similar to some extent to those found in Isa Town (Bahraian), which related to similar arid and low precipitation climatic conditions. The effect of phosphate mining activities was obvious as indicated from the presence of apatite as the main mineral phase and the higher P contents. Moreover, the studied samples contain higher Zn, Ni, Cu and to lesser extent Cr than blank samples. They exhibited a significant positive correlation with P, as they are usually associated with the phosphate rocks.  相似文献   

6.
This paper presents the analysis and interpretation of ambient particulate matter concentrations measured as PM10 at a network of six air monitoring stations in Kathmandu valley during the years, 2003 through 2005. The purpose was to understand the pollution trends associated with different areas considering levels particulate matter concentrations representing the ambient air quality of Kathmandu valley. The study indicate that particulate concentrations (PM10) measured are persistently higher at air sampling sites representing roadside areas compared to the background sites. The inter-station network variability with respect the particulate pollution suggests optimizing resources. The comparison of annual average PM10 concentration observed at six air-monitoring sites in Kathmandu Valley with standard annual average concentration prescribed by World Health Organization as well as Europe Union indicates serious PM10 pollution in Kathmandu valley.  相似文献   

7.
The objective of this paper is to analyze temporal and seasonal trends of air pollution in Bahrain between 2006 and 2012 by utilizing datasets from five air quality monitoring stations. The non-parametric and robust Theil-Sen approach is employed to study quantitatively temporal variations of particulate matter (PM10 and PM2.5), nitrogen dioxide (NO2), sulfur dioxide (SO2), and ozone (O3). The calculated annual concentrations for PM10 and PM2.5 in Bahrain were substantially higher than recommended World Health Organization (WHO) guideline standards. Results showed increasing trends for PM10, PM2.5, and SO2 whereas O3 and its precursor NO2 showed decreasing behavior. The general increase in air pollution trends is in agreement with prediction of air pollution models for Middle East region due to economic growth, industrialization, and urbanization. The significances of long-term trends were examined. Additional to actual (unadjusted) trends, meteorological adjusted (deseasonalized) trends and seasonal trends were quantified. The box-plot analysis visually illustrated monthly variations of key air pollutants. It showed that only PM10 and PM2.5 exhibited seasonal pattern, and their concentrations increased during summer and decreased during winter. The effects of ambient air temperature, relative humidity, wind speed, and rainfall on particulate matter (PM) concentrations were further investigated. The Spearman correlation coefficient results demonstrated significant negative correlation between relative humidity and PM concentrations (??0.595 for PM10 and ??0.526 for PM2.5) while significant positive correlation was observed between temperature and PM concentrations (0.420 for PM10 and 0.482 for PM2.5).  相似文献   

8.
Particulate matter concentration and assessment of its movement pattern is crucial in air pollution studies. However, no study has been conducted to determine the PM10 concentration using atmospheric correction of thermal band by temperature of nearest dark pixels group (TNDPG) of this band. For that purpose, 16 Landsat Enhanced Thematic Mapper plus ETM+ images for Sanandaj and Tehran in Iran were utilized to determine the amount of PM10 concentration in the air. Thermal infrared (band 6) of all images was also used to determine the ground station temperature (GST b6) and temperature of nearest dark pixels group. Based on atmospheric correction of images using temperature retrieval from Landsat ETM+, three empirical models were established. Non-linear correlation coefficient with polynomial equation was used to analyze the correlations between particulate matter concentration and the ground station temperature for the three models. Similar analyses were also undertaken for three stations in Klang Valley, Malaysia, using 11 Landsat ETM+ images to show the effectiveness of the model in different region. The data analysis indicated a good correlation coefficient R = 0.89 and R = 0.91 between the trend of the result of temperature of nearest dark pixels group b6 ? (GST b6 ? GST) model and the trend of PM10 concentration in Iran and Malaysia, respectively. This study reveals the applicability of the thermal band of Landsat TM and ETM+ to determine the PM10 concentration over large areas.  相似文献   

9.
Santiago de Chile is a big city with huge air quality problems, being one of the most polluted cities in the world. This is aggravated during winter by the topography and meteorological conditions of the city. Although public policies have been developed to minimise the atmospheric aerosol pollution, there is a lack of adequate knowledge and poor characterisation of these aerosols (in its PM2.5 and PM10 fractions). In this study we sampled atmospheric particles during winter in two distinct areas of Santiago: downtown (Teatinos Street) and in a more residential area (Macul). Major (Si, Al, Fe, Ca and K) and some trace element (S, Cl, Ti, P, Cr, Cu and Zn) compositions were obtained by proton-induced X-ray emission (PIXE). Morphological, type and chemical characterisation was also performed using scanning electron microscopy (SEM) coupled with an energy dispersive X-ray microanalysis system (SEM–EDX). Besides the carbon particles, the contribution of which can be quite important in the atmospheric aerosol, especially in downtown, unambiguously lithogenic (i.e. of geological origin) particles and elements are the second highest contributors. Enrichment factor calculation, together with particle identification and element correlation allow the origin of some elements and particles to be traced, revealing anthropogenic origins for some of them that are specific to the Santiago area.  相似文献   

10.
Landslides frequently occur during large earthquakes and storms in Taiwan, supplying large volumes of sediment to downslope areas. When coupled with the intense northeast monsoon over Taiwan in the dry winter season, this can lead to high concentrations of airborne particulates that are hazardous to human health. Air quality monitoring stations near unvegetated riverbanks recorded high concentrations of particulate matter less than 10 μm (PM10) after Typhoon Morakot in 2009. The objective of this study was, therefore, to analyze the effects on air quality of sediment caused by the typhoon. A deflation module was simulated, and the resulting estimates were compared with observed data from the Taitung monitoring station for 2004 and 2005. The relationship of dust flux to average atmospheric dust concentration was analyzed for October to December 2001–2010. Analysis showed that the 2001–2008 data are highly correlated (0.78) with the average concentration. The intercept of 28.07 represented the background concentration with no dust emission, from October to December of 2001–2008. Based on the dust flux potential in 2009, the average yearly PM10 concentration would be 37.98 µg/m3; however, the measured concentration was 61.67 µg/m3 from October to December. This suggests the strong influence of dust re-suspended from unvegetated riverbanks by Typhoon Morakot.  相似文献   

11.
Based on data from ground-based air quality stations, space–time variations of six principal atmospheric pollutants, such as particulate matter (PM2.5 and PM10) and gas pollutants (SO2, NO2, СО, and O3), obtained from January 1, 2014 to December 31, 2017 in the city of Lanzhou, have been studied. Average total concentrations of PM2.5 and PM10 were 53.2?±?26.91 and 124.54?±?82.33 µg/m3, respectively; however, the results showed that in 75.53% and 84.85% days, concentrations of these pollutants exceeded Chinese National Ambient Air Quality Standard and in 100% days exceeded World Health Organization guidelines standards. Daily mean values of aerosol optical depth and Ångström exponent based on data, received by satellite Moderate Resolution Imaging Spectroradiometer, show a broad range of values for aerosol optical depth (from 0.018 to 1.954) and Ångström exponent (from 0.003 to 1.8). Results of principal components analysis revealed three factor loadings. Thus, Factor 1 has the relevant loadings for PM2.5, PM10, CO, SO2, and NO2 (36%) and closely associated with transport emissions and industrial sources, which contribute to air pollution in Lanzhou. Factor 2 was heavily loaded with temperature and visibility (16.94%). Factor 3 consisted of relative humidity (14.11%). Cluster analysis revealed four subgroups: cluster 1 (PM2.5, NO2, SO2), cluster 2 (CO), cluster 3 (PM10) and cluster 4 (relative humidity, visibility, temperature, O3, wind speed), which were compliant with results, obtained from principal components analysis. Positive correlation was found among all pollutants, other than O3. According to processed backward trajectories obtained by Hybrid Single-Particle Lagrangian Integrated Trajectory model, it was found that movement of air masses occur from north, northwest, and west directions—the location of principal natural sources of aerosols.  相似文献   

12.
Due to rapid economic growth of the country in the last 25 years, particulate matter (PM) has become a topic of great interest in China. The rapid development of industry has led to an increase in the haze created by pollution, as well as by high levels of urbanization. In 2012, the Chinese National Ambient Air Quality Standard (NAAQS) imposed ‘more strict’ regulation on the PM concentrations, i.e., 35 and 70 μg/m3 for annual PM2.5 and PM10 in average, respectively (Grade-II, GB3095-2012). The Pearson’s correlation coefficient was used to determine the linear relationship of pollution between pollution levels and weather conditions as well as the temporal and spatial variability among neighbouring cities. The goal of this paper was to investigate hourly mass concentration of PM2.5 and PM10 from June 1 to August 31, 2015 collected in the 11 largest cities of Gansu Province. This study has shown that the overall average concentrations of PM2.5 and PM10 in the study area were 26 and 66 μg/m3. In PM2.5 episode days (when concentration was more than 75 μg/m3 for 24 hrs), the average concentrations of PM2.5 was 2–3 times higher as compared to non-episode days. There were no observed clear differences during the weekday/weekend PM and other air pollutants (SO2, NO2, CO and O3) in all the investigated cities.  相似文献   

13.
Based on long-term PM2.5 data observed at high temporal and spatial resolution, the relationships between PM2.5, primary emission, and weather factors in China during four seasons were examined using statistical analysis. The results reveal that primary emission plays a decisive role in the spatial distribution and seasonal variability of PM2.5, except in western China, where PM2.5 is controlled by dust weather. In addition to the accumulation of primary emissions, unfavorable meteorological conditions for the diffusion of air pollution lead to the occurrence of PM2.5 pollution. The significant dynamic factors affecting PM2.5 concentration are surface wind speed, planet boundary layer height, and ventilation coefficient, especially in winter. The ventilation coefficient is inversely correlated with PM2.5. Better ventilation is more favorable for the dilution and outflow of local PM2.5. However, in spring and autumn, ventilation coefficient and PM2.5 are positively correlated over the southern regions with low emission, indicating that ventilation also affects the inflow of PM2.5 from outside the region. Wind shear, 850 hPa divergence, and vertical velocity have insignificant effects on the long-term variations in PM2.5. The significant thermal factor is 850 hPa temperature in winter, except in the Pearl River Delta and Xinjiang regions. In spring, the influence of each thermal factor is weak. In summer, the influences of temperature and humidity are more significant than in spring. In autumn, the influence of humidity is relatively obvious, compared with other thermal factors. The correlation coefficients between multi-factors regressed and observed PM2.5 concentrations pass the 95% confidence test, and are higher than that of single-factor regression over most regions. The observed data from December 2016 to February 2017 were chosen to test the regression equation. The test result reveals that the regression equation is effective for predicting PM2.5 concentrations over regions with high primary emission.  相似文献   

14.
This paper gives detailed comprehensive review of atmospheric assessment of particulate matter and heavy metals. Previous research works executed on this subject matter in the past four decades were adequately scrutinized. Various equipments for assessing atmospheric particulate matter and heavy metals were presented. Mathematical modeling equations for source apportionment and characterization, deposition rate prediction and health risk characterization of PM10 were also presented. However, the following conclusions were made: (1) there is need for improvement on the mathematical models by reducing the number of assumptions made in developing them. (2) Comparative analysis of concentrations of heavy metals in the atmosphere under the same environment for different methodologies should be executed for accuracy purposes. (3) Cost implication of assessing, monitoring and controlling these unfriendly substances should be examined, and hence, involvement of cost engineers may be of immense help. (4) Further research works should be done on Air-Q 2.2.3 model currently identified as a new methodology for provision of quantitative data on the impact of particulate matter exposure on the health of people. (5) Compliance monitoring networks should be designed to ease data collection for the observables, locations and time periods that allowed receptor models to be applied. (6) There is need for much more research works that enable optimal control and regulation of emission of heavy metals into the atmosphere in order to reduce health effects of these inhalable substances.  相似文献   

15.
In this study, several multivariate methods were used for forecasting hourly PM10 concentrations at four locations based on SO2 and meteorological data from the previous period. According to the results, boosted decision trees and multi-layer perceptrons yielded the best predictions. The forecasting performances were similar for all examined locations, despite the additional PM10 spatio-temporal analysis showed that the sites were affected by different emission sources, topographic and microclimatic conditions. The best prediction of PM10 concentrations was obtained for industrial sites, probably due to the simplicity and regularity of dominant pollutant emissions on a daily basis. Conversely, somewhat weaker forecast accuracy was achieved at urban canyon avenue, which can be attributed to the specific urban morphology and most diverse emission sources. In conclusion to this, the integration of advanced multivariate methods in air quality forecasting systems could enhance accuracy and provide the basis for efficient decision-making in environmental regulatory management.  相似文献   

16.
This paper presents results of an atmospheric particulate matter (PM) monitoring and source apportionment study conducted during summer and fall 2010 in Cairo. These results are compared to those of similar studies in 1999 and 2002. Concentrations of PM2.5 and PM10 mass and their chemical constituents were determined and chemical mass balance modeling was conducted to estimate the source contributions to ambient PM. Emphasis was placed on characterizing the long-term trends in atmospheric lead (Pb) concentrations and their sources in Cairo. PM2.5 and PM10 concentrations were highest during fall 1999 at four of the five study sites. This was also the case for open (vegetative/trash) burning contributions, which showed a smaller increase during fall 2010. Burning of agricultural waste after the fall harvest continues to be a major source of PM in Cairo. Both PM2.5 and PM10 mass decreased dramatically at Shobra, an industrial site, from 1999 to 2010. A reduction of lead smelting has resulted in a decrease of ambient Pb concentrations of up to two orders of magnitude from 1999 to 2010 at Shobra, El-Zamalek, and El-Qualaly. From 1999 to 2010, the mobile source contribution has been relatively stable at most of the study sites. Future efforts to reduce ambient PM should focus on controlling emissions from motor vehicles and open burning and implementing mitigation strategies for reducing resuspended road and construction dust.  相似文献   

17.
The increasing emission of primary and gaseous precursors of secondarily formed atmospheric particulate matter due to continuing industrial development and urbanization are leading to an increased public awareness of environmental issues and human health risks in China. As part of a pilot study, 12-h integrated fine fraction particulate matter (PM2.5) filter samples were collected to chemically characterize and investigate the sources of ambient particulate matter in Guiyang City, Guizhou Province, southwestern China. Results showed that the 12-h integrated PM2.5 concentrations exhibited a daytime average of 51 ± 22 µg m?3 (mean ± standard deviation) with a range of 17–128 µg m?3 and a nighttime average of 55 ± 32 µg m?3 with a range of 4–186 µg m?3. The 24-h integrated PM2.5 concentrations varied from 15 to 157 µg m?3, with a mean value of 53 ± 25 µg m?3, which exceeded the 24-h PM2.5 standard of 35 µg m?3 set by USEPA, but was below the standard of 75 µg m?3, set by China Ministry of Environmental Protection. Energy-dispersive X-ray fluorescence spectrometry (XRF) was applied to determine PM2.5 chemical element concentrations. The order of concentrations of heavy metals in PM2.5 were iron (Fe) > zinc (Zn) > manganese (Mn) > lead (Pb) > arsenic (As) > chromium (Cr). The total concentration of 18 chemical elements was 13 ± 2 µg m?3, accounting for 25% in PM2.5, which is comparable to other major cities in China, but much higher than cities outside of China.  相似文献   

18.
The emissions from palm oil industry through incineration and open burning are the major sources of air pollutions contribution in Malaysia. The consequence of increasing the particulate concentration, the particulate matter dissolves with vapour and grows into droplets when the humidity exceeds approximately 70% and causing opaque situation known as haze. This work focuses on the dispersion particulate matter from palm oil mill. Gaussian Plume Model from a point source, subject to various atmospheric conditions is used to calculate particulate matter concentration then display the distribution of plume dispersion using geographic information system. Atmospheric Stability, mixing height, wind direction, wind speed, natural and artificial features play an important role in dispersion process. Study on the dispersion of particulate matters and the haze potential are presented as a case study in this paper. The data obtained will be served as the purpose of modeling the transport of particulate matter for obtaining permits and prevention of significant deterioration to the environment.  相似文献   

19.
Air particulate matter (PM) samples were collected from June 2006 to May 2007 for determination of chemical elements. PM samples were taken in two size fractions (PM2.5 and PM10) with MiniVolume air samplers on rooftops of various buildings (15–25 m above ground) in the city of Riyadh. The samples were subjected to X-ray fluorescence analysis to measure major (Na, Mg, Al, K, Ca, Si, P, S, and Fe) and trace elements (Mn, Ni, Cu, Zn, and Ba). The results showed that the PM concentrations were higher for PM10 compared to PM2.5, indicating that the major PM source was local dust. Also the spatial distribution with high PM concentrations was observed in the south and southeast of the city and the lowest levels were in the center and northeast of the city. This spatial distribution was attributed to different factors such as wind direction and velocity, emission from cement factories, and the presence of buildings, trees, and paved streets that reduce the amount of dust resuspended into the atmosphere. The air quality of the city was found to range from good to hazardous based on PM2.5, and from good to very hazardous based on PM10. The element-enrichment factors revealed two element groups according to their changing spatial behavior. The first group showed no significant spatial changes indicating they have the same common source. The second group (mainly S and Ni) exhibited significant changes as expected from anthropogenic inputs. The origin of S is possibly a combination of minerals (CaSO4) and fossil fuel combustion. The source of Ni is probably from fossil fuel combustion.  相似文献   

20.
Compliance with U.S. air quality regulatory standards for atmospheric fine particulate matter (PM2.5) is based on meeting average 24 hour (35 μ m?3) and yearly (15 μg m?3) mass‐per‐unit‐volume limits, regardless of PM2.5 composition. Whereas this presents a workable regulatory framework, information on particle composition is needed to assess the fate and transport of PM2.5 and determine potential environmental/human health impacts. To address these important non‐regulatory issues an integrated approach is generally used that includes (1) field sampling of atmospheric particulate matter on filter media, using a size‐limiting cyclone, or with no particle‐size limitation; and (2) chemical extraction of exposed filters and analysis of separate particulate‐bound fractions for total mercury, trace elements and organic constituents, utilising different USGS laboratories optimised for quantitative analysis of these substances. This combination of sampling and analysis allowed for a more detailed interpretation of PM2.5 sources and potential effects, compared to measurements of PM2.5 abundance alone. Results obtained using this combined approach are presented for a 2006 air sampling campaign in Shenandoah National Park (Virginia, USA) to assess sources of atmospheric contaminants and their potential impact on air quality in the Park. PM2.5 was collected at two sampling sites (Big Meadows and Pinnacles) separated by 13.6 km. At both sites, element concentrations in PM25 were low, consistent with remote or rural locations. However, element/Zr crustal abundance enrichment factors greater than 10, indicating anthropogenic input, were found for Hg, Se, S, Sb, Cd, Pb, Mo, Zn and Cu, listed in decreasing order of enrichment. Principal component analysis showed that four element associations accounted for 84% of the PM2.5 trace element variation; these associations are interpreted to represent: (1) crustal sources (Al, REE); (2) coal combustion (Se, Sb), (3) metal production and/or mobile sources (Mo, Cd, Pb, Cu, Zn) and (4) a transient marine source (Sr, Mg). Concentrations of Hg in PM2.5 at background levels in the single pg m?3 were shown by collection and analysis of PM2.5 on filters and by an automated speciation analyser set up at the Big Meadows air quality site. The speciation unit revealed periodic elevation of reactive gaseous mercury (RGM) that co‐occurred with peaks in SO2, indicating an anthropogenic source. GC/MS total ion current chromatograms for the two sites were quite similar indicating that organic signatures were regional in extent and/or that the same compounds were present locally at each site. Calculated carbon preference index values for n‐alkanes indicated that plant waxes rather than anthropogenic sources, were the dominant alkane source. Polycyclic aromatic hydrocarbons (PAHs) were detected, with a predominance of non‐alkylated, and higher molecular weight PAHs in this fraction, suggestive of a combustion source (fossil fuel or forest fires).  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号