首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献,搜索用时 62 毫秒
1.
2013年7月22日7时45分,在甘肃省定西市岷县和漳县交界(34.5°N,104.2°E)发生了一次MS6.6地震,震源深度20 km.截至7月29日8时,甘肃岷县、漳县MS6.6地震共记录到余震1 034次,其中3.0级以上余震9次,包括5.0~5.9级1次,4.0~4.9级1次,3.0~3.9级7次.其中最大余震为发生在7月22日9时12分的MS5.6地震.地震造成95人死亡,1 366人受伤.震区地处青藏高原与西秦岭陇南山地接壤区,黄土覆盖较厚,地形起伏较大,山坡陡峭,沟壑纵横,地震引发了黄土滑坡、崩塌和塌陷等次生灾害.另外,震区经济发展较为落后,房屋结构差,土木结构房屋所占比例较高,抗震性能差,是这破坏较重的主要原因.受灾范围涉及定西市、白银市、天水市、陇南市、甘南藏族自治州和临夏回族自治州等6个市(州)13个县,面积约1万多km2.甘肃天水、兰州、陇南、白银,陕西的宝鸡、汉中、咸阳、西安及四川成都、绵阳等地都有震感.地震发生后,中国地震局迅速组织地震现场考察队赶赴灾区,进行震情监测、烈度评定、震害损失评估和科学考察等工作,并于7月24日14时发布了甘肃岷县漳县6.6级地震烈度图.本次地震宏观震中位于岷县梅川镇永光、永星村和禾驮乡的拉路村一带,极震区烈度为Ⅷ度.烈度长轴走向为北西向,与区域构造线相一致.本文归纳总结了岷县、漳县MS6.6地震的基本参数、烈度分布、震害特征和发震构造背景等基本特征.本次地震发生在青藏高原东缘的甘东南地区,该区是南北地震带与昆仑山—秦岭断裂带等活动构造交汇部分部位,也是北西西向的东昆仑断裂与西秦岭北缘断裂之间的构造转换区.地震发生在靠近临潭—宕昌断裂一侧.通过野外地质调查,发现通过极震区有一条断层,即禾驮乡断层为活动断层,为晚更新世活动断层.包括滑坡、地裂缝、地震陷坑和喷沙冒水等地表破坏现象沿断层成带状分布.在震源机制解方面,且震源机制解也与该断层相吻合.中国地震局地球物理研究所给出节面Ⅱ走向为320°,与禾驮乡断层相一致.中国地震局地质研究所给出的是301.3°,也基本与其吻合.两个单位所给出的滑动面倾向为51°和57.3°,皆为向北东倾,与禾驮乡断层倾向也相一致.另外发现安家山滑坡长约310m,宽约30 ~ 35 m,沿断层谷地呈长舌形向北西做水平滑动,滑动面上擦痕侧俯角为12°~23°,主滑动面走向与断层走向相一致.说明禾驮乡断层为此次地震的发震断层,该断层属于区域上临潭—宕昌断裂的次级断层,该断裂历史上在本区内曾发生过3次6级以上强震,近期又发生过2003年11月13日岷县5.2级地震和2004年9月7日岷县—卓尼5.0级地震.此次地震是临潭—宕昌断裂进一步活动的结果.  相似文献   

2.
小金5.0级地震的主要破坏区沿抚边河分布,等烈度线总体轮廓呈“猪腰”形,其长轴方向为北25°西。极震区(白果坪Ⅶ°)内的房屋受到了不同程度的破坏或损坏;Ⅵ°、Ⅴ°区内的房屋大多在1989年5.0级和6.6级地震破坏或损坏的基础上震害加重。  相似文献   

3.
1986年3月13日16时41分19秒,在云南省鹤庆县北衙区、黄坪区(北纬26°12’、东经100°11’)一带发生5.3级(M_s)地震。极震区烈度为六度强,长轴北西方向,长16公里、宽4公里。地震使北衙、黄坪两区的房屋遭到了不同程度的破环,有八人受轻伤。1987年5月18日10时03分08秒,该处又发生一次5.0级(M_s)地震,震中为北纬26°11’,东经100°11’,极震区烈度为六度,长轴仍为北西向,长9.5公里,宽3公里。  相似文献   

4.
云南耿马7.2级地震破裂与震源应力场   总被引:2,自引:0,他引:2  
1 98 8年 1 1月 6日在云南省澜沧县和耿马县境内先后发生了 7.6级和 7.2级强烈地震。其中 7.2级地震在震中区小黑江两岸灰岩裸露区出现了具有构造意义的地裂缝带。采用断层滑动矢量法反演出形成上述地裂缝带的应力张量为 :σ1走向 2 2 3°,倾角 2 8°;σ2 走向 42°,倾角6 2°;σ3 走向 1 3 3°,倾角 0°;应力比 R=0 .5 7,总体显示出走滑兼压性特征 ,基本代表了震源机制解所反映的震源应力场特征。断面滑动矢量解析可做为一种判定地裂缝是否是构造成因的方法  相似文献   

5.
1992年7月30日西藏尼木6.5级地震宏观考察   总被引:1,自引:0,他引:1  
尼木6.5级地震的主要破坏区分布在尼木县东北部与当施县交界处,等烈度线总体呈北35°东展布的椭圆形。极震区(朋果至多那一带,I_0=Ⅶ)内的房屋受到了较严重的破坏或损坏。这次地震的发震构造为尼木南北向活动构造带中的一条北北东向断裂。  相似文献   

6.
王辉  谷一山 《地震学报》1991,13(3):344-353
1988年11月6日,在云南省西南部的澜沧-耿马断裂带上发生了两次大于7级的地震.地震造成的严重破坏和人员伤亡主要是由于极震区内抗震性能极差的毛石房、砖柱土坯房的大量倒塌所致.澜沧地震的震中基本烈度可达Ⅸ度,耿马地震极震区烈度达Ⅹ度.澜沧地震构造活动的地表证据主要是出现在极震区内的张性地裂缝带和小断层陡坎.地裂缝带和小断坎主要出现在四条相对连续的北北西走向的狭窄地带内,其长度从几百 m 到6km 不等.澜沧地震地表破裂带长约35km,宽约3km,最大垂直位移量和最大右旋水平位移量分别为1.5m 和1.4m.耿马地震地表断裂活动的明显证据包括一系列北北西走向的地裂缝带和一段长约5km的地震断层陡坎.耿马地震地表破裂带长约24km,其最大垂直位移3.5m,最大右旋水平位移为3m.两次地震形成的地表破裂带均具有右旋-正断层性质.本文讨论了这两次地震的 度分布及地表破裂特征.   相似文献   

7.
云南耿马7.2级地震地表破裂带研究   总被引:2,自引:1,他引:2       下载免费PDF全文
根据野外考察的实际资料,本文介绍了耿马7.2级地震地表破裂带的展布,结构要素及组合、位移分布等情况。同时依据位错资料对破裂带的应力活动及断裂两盘的运动状态进行了初步分析。认为本次地震发震构造以右旋走滑为主兼具张性,主压应力优势方位为N5°—10°E。断层两盘相对运动的总体方向为N55°W左右,断层运动的滑移角在30°—40°之间  相似文献   

8.
澜沧—耿马地震发震构造初步研究   总被引:2,自引:0,他引:2  
本文根据澜沧—耿马地震形变带、极震区及余震序列分布特征,分析了7.6和7.2级地震的发震构造,认为北北西向旱母坝断层是7.2级地震的发震构造,7.6级地震的发震构造不是一条单一的断层,北西向木嘎断裂和北北西向澜沧—勐海断裂均有明显破裂表现,这一特点与震区复杂的地质构造背景有密切联系。  相似文献   

9.
1986年8月26日门源6.4级地震考察初步总结   总被引:2,自引:4,他引:2       下载免费PDF全文
考察结果表明,地震宏观震中位于北纬37°37′、东经101°38′,震中烈度约Ⅷ度、震源深度13公里。Ⅵ度区面积为2600平方公里,长轴方向为N55°W。发震断层为冷龙岭山脊断层,该断层走向为N60°W,属于北祁连断裂带中段的组成部份。文中初步总结了有关地震前兆资料和震区宏观异常现象,对震区地震趋势进行了初步讨论。  相似文献   

10.
2003年2月24日新疆巴楚-伽师6.8级地震发震构造   总被引:14,自引:0,他引:14       下载免费PDF全文
2003年2月24日发生在新疆塔里木盆地的巴楚-伽师6.8级地震可能是1997—1998年伽师强震群的继续,但其震源机制解、破裂过程与1997—1998年的强震群有一定的差别。从地震重新定位的结果看,巴楚-伽师6.8级地震与塔西南坳陷东侧麦盖提斜坡带上发育的一组NWW向隐伏逆断层有关,地震宏观考察①所发现的与构造变形有关的地裂缝也与这一隐伏断层带的位置相吻合,等震线形态与隐伏断层带的走向一致,极震区的形态与断层的破裂方向基本一致。这些均表明这次地震是盆地内一条近EW向北倾逆断层自NW向SE由深至浅破裂的结果  相似文献   

11.
Crack reservoir beds have large proportion in China. With the development of exploration in basins, the ratio of the crack reservoir beds will grow year after year. There have been 15 crack buried hill reservoirs since the first wellbore was successfully drilled in carbonate rock and Zhengjia granite in the Zhuangxi area in the 1980s[1]. Also mudstone-crack reservoirs and compact low-penetrability reservoirs have been discovered. With the development of exploration and exploitation in oil fi…  相似文献   

12.
Large‐scale, servo‐hydraulic shake tables are a central fixture of many earthquake engineering and structural dynamics laboratories. Wear and component failure from frequent use may lead to control problems resulting in reduced motion fidelity, necessitating repairs and replacement of major components. This paper presents a methodology to evaluate shake table performance pre‐ and post‐repair, including the definition of important performance metrics. The strategy suggested is presented in the context of the rebuilding of a 4.9 × 3.1 m, 350‐kN‐capacity uniaxial shake table. In this case, the rebuild consisted of characterization of wear to table components, replacement of worn bearing surfaces, and replacement of hydraulic accumulators. To assess the effectiveness of the repair actions, sinusoidal and triangular waves, white noise, and earthquake histories were run on the table before and after the rebuild. The repair actions were successful in reducing the position and velocity dependence of friction, improving the ability of control algorithms to accurately reproduce earthquake motions. The maximum and average response spectral misfits in the period range of 0.1–2 seconds were reduced from approximately 50% to 15%, and from 5% to less than 2.5%, respectively.  相似文献   

13.
轴地壳岩浆房是活动扩张中心海洋地壳结构的一个重要组成部分,轴地壳岩浆房通过深部岩浆源的补充,内部岩浆的同化熔融、结晶分异等岩浆房过程,其中的岩浆会破裂上覆的岩石层形成岩浆破裂,并沿岩浆破裂继续向上迁移。本文建立了岩浆迁移的层流模型,从理论上对岩浆迁移问题进行了探讨,并将遗传算法引入到该问题中来,用遗传算法求解了描述岩浆驱动破裂传播的积分方程。如果假设岩浆破裂在远离破裂末梢处的权限宽度为1M,则靠近末梢,破裂的宽度逐渐加大,在末梢处宽度为2m左右。并根据文献对岩浆流体的一些观测参数计算得出,岩浆破裂权限宽度不会很大,一般在1m左右的量级。  相似文献   

14.
Shaking‐table data for a tuned liquid damper with a sloped bottom of 30° with the horizontal are investigated using a non‐linear numerical model previously developed by Yu, Jin‐kyu, Nonlinear characteristics of tuned liquid dampers. Ph.D. Thesis, Department of Civil Engineering, University of Washington, Seattle, WA, 98195 (1997). Stiffness and damping parameters for this model are obtained and compared with those previously derived for box‐shaped tanks. The values for these parameters reflect the softening spring behaviour of the sloped‐bottom system in contrast to the hardening system evident for the box‐shaped TLD. Consequently, the sloped‐bottom tank should be tuned slightly higher than the fundamental structural frequency in order to obtain the most effective damping. Copyright © 2001 John Wiley & Sons, Ltd.  相似文献   

15.
1976年唐山大地震至今已30年,唐山的震后建设先后经历了抗灾建设、恢复建设和发展建设三个阶段。三个不同的建设阶段所采用的抗震结构体系有所不同,也反映了我国抗震理论和实践的进步与发展。本文总结了三个不同建设时期唐山市建筑工程采用的主要抗震结构体系,并对唐山市建筑抗震结构体系的发展提出了建议。  相似文献   

16.
Development and testing of a serially multiplexed fiber optic sensor system is described. The sensor differs from conventional fiber optic acoustic systems, as it is capable of sensing AE emissions at several points along the length of a single fiber. Multiplexing provides for single channel detection of cracks and their locations in large structural systems. An algorithm was developed for signal recognition and tagging of the AE waveforms for detection of crack locations. Laboratory experiments on plain concrete beams and post-tensioned FRP tendons were performed to evaluate the crack detection capability of the sensor system. The acoustic emission sensor was able to detect initiation, growth and location of the cracks in concrete as well as in the FRP tendons. The AE system is potentially suitable for applications involving health monitoring of structures following an earthquake Supported by: National Science Foundation, Grant number CMS-9900338  相似文献   

17.
Physical modelling of cracked/fractured media using downscaled laboratory experiments has been used with great success as a useful alternative for understanding the effect of anisotropy in the hydrocarbon reservoir characterization and in the crustal and mantle seismology. The main goal of this work was to experimentally verify the predictions of effective elastic parameters in anisotropic cracked media by Hudson and Eshelby–Cheng's effective medium models. For this purpose, we carried out ultrasonic measurements on synthetic anisotropic samples with low crack densities and different aspect ratios. Twelve samples were prepared with two different crack densities, 5% and 8%. Three samples for each crack density presented cracks with only one crack aspect ratio, whereas other three samples for each crack density presented cracks with three different aspect ratios in their composition. It results in samples with aspect ratio values varying from 0.13 to 0.26. All the cracked samples were simulated by penny‐shaped rubber inclusions in a homogeneous isotropic matrix made with epoxy resin. Moreover, an isotropic sample for reference was constructed with epoxy resin only. Regarding velocity predictions performed by the theoretical models, Eshelby–Cheng shows a better fit when compared with the experimental results for samples with single and mix crack aspect ratio (for both crack densities). From velocity values, our comparisons were also performed in terms of the ε, γ, and δ parameters (Thomsen parameters). The results show that Eshelby–Cheng effective medium model fits better with the measurements of ε and γ parameters for crack samples with only one type of crack aspect ratio.  相似文献   

18.
闭合裂纹面相互作用的实验研究   总被引:4,自引:0,他引:4       下载免费PDF全文
为了研究地震过程中断层面的相互作用,设计了四类裂纹面状况不同的断裂力学实验。实验结果表明,裂纹面的状况对于含裂纹材料的σc(21/2)值有强烈的影响,并利用断裂力学的原理对结果进行了分析。 实验中解决了如下技术关键: 1.可用三点弯曲、局部受拉、单面启裂、双面贯穿的方法,在脆性材料板状试件(玻璃板、岩石板)以及有机玻璃板中预制中心穿透裂纹。 2.在裂纹端部预计裂纹扩展的区域内粘贴电阻应变片,用以判断并测量裂纹初始扩展及其相应的破坏应力σc的方法。  相似文献   

19.
小波分析在结构损伤识别中的应用   总被引:1,自引:0,他引:1  
为提高结构损伤识别方法的准确性和适用性,将小波分析引入到结构损伤识别中。本文首先介绍了小波分析的基本原理,然后详细论述了小波分析用于结构损伤识别的三种方法:基于时域响应的方法、基于空间域响应的方法和小波分析与其他方法联合使用,接着分析了各种方法的应用现状、适用范围和存在的问题。通过比较可以看出小波分析用于结构损伤识别有着广阔的应用前景,本文最后针对进一步研究的方向提出了五点建议。  相似文献   

20.
提出了渤海湾盆地初期挤压、早期张压交替、中后期持续张裂的新的成盆模式,并在该模式指导下,以济阳坳陷为例总结了盆内深层压性、张性、张压复合作用等多种成因的构造圈闭类型及其石油地质意义,最后指出盆内勘探的有利方向.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号