共查询到20条相似文献，搜索用时 140 毫秒
1.
Ali Lashkari 《国际地质力学数值与分析法杂志》2013,37(8):904-931
Using pile segment analysis, the mobilized shaft resistance of axially loaded nondisplacement piles in sand is investigated here. It is accepted that the shaft capacity of piles constructed in granular soils is highly influenced by the mechanical behavior of soil–structure interfaces forming adjacent the piles skin. Adopting the thin interface layer as a load transfer mechanism, a simple but accurate critical state compatible interface constitutive model is introduced. After evaluation, the interface model in conjunction with the pile segment analysis is applied for the prediction of the shaft resistance mobilized in nondisplacement piles. The proposed approach takes into account the influences of pile diameter and surface roughness together with the effects of the surrounding soil density and stiffness on the mobilized shaft resistance. The performance of the proposed method is verified by comparing its predictions with the experimental data of various model piles covering wide ranges of length, diameter, roughness, and surrounding soil properties. Copyright © 2012 John Wiley & Sons, Ltd. 相似文献
2.
This paper presents the results of three-dimensional, finite element analyses performed with an advanced, two-surface-plasticity, constitutive sand model to investigate the response of non-displacement piles to axial loading. The analysis domain is carefully meshed such that the formation and evolution of shear bands next to the pile shaft and near the pile base can be properly captured. Analyses considering various soil profiles and pile geometries show that the mobilized lateral earth pressure coefficient K along the pile shaft increases with increasing relative density and decreasing initial confining stress. The ultimate unit base resistance is independent of pile diameter, increasing with increasing relative density and increasing initial confining stress at the pile base. Based on the analysis results, design equations are proposed to estimate the limit shaft resistance and ultimate base resistance of non-displacement piles in sandy soil. In proposing these relationships, the pile slenderness ratio is considered. The effect of layer proximity to the base of the pile or pile base embedment in a layer is also considered. 相似文献
3.
根据弹性力学原理,提出了模型筒桩（闭合墙）的简化力学模型。采用半逆解法先求出桩左右侧受均布摩阻力、桩顶受均布荷载两种情况下的应力分量,根据叠加原理得出桩两侧均受相同摩阻力、桩顶受均布荷载情况下的应力分量。据此推导了普通桩基的轴力和侧摩阻力计算式,分析结果表明,该计算式与传统计算方法是一致的。当桩壁两侧受不同大小的侧摩阻力、桩顶受均布荷载时,仍采用叠加原理求得各应力分量,进而求得桩表面处的轴向应变与单位侧摩阻力关系的解析解。通过矩形闭合墙基础模型试验实例,对该解析解的应用方法加以说明。该解析解的求出,为竖向载荷试验中模型筒桩（闭合墙）所量测的内外侧应变进行数据处理提供了理论依据,进而为基础-土相互作用研究提供了真实、准确的试验结果。 相似文献
4.
5.
结合基桩承载过程中的桩周土体应力状态分析和桩土界面摩擦特性分析,推导出基于土体应力状态的沿桩土界面的土体抗剪强度计算模型和基于界面摩擦特性的界面抗剪强度计算模型。通过对比土体抗剪强度和界面抗剪强度,推导出受该两种强度耦合作用影响的极限侧阻力计算模型,并用上海某工程算例验证该模型的合理性和可行性,同时利用该模型分析不同类型的土的极限侧阻力随埋深的分布规律。结果显示：因内摩擦角和侧压力系数之间的不同关系,极限侧阻力随埋深表现出不同的分布特点,在特定关系下,存在一个临界深度,超过该深度极限侧阻力维持在一个稳定值甚至不断减小直至为零。 相似文献
6.
通过模型试验研究了竖向荷载作用下砂土中斜桩的荷载传递性状,分析了桩身倾角及长径比对斜桩桩身轴力、弯矩、剪力、桩侧摩阻力及端阻比的影响。试验结果表明：在桩顶竖向荷载作用下,斜桩桩身轴力均小于相应直桩桩身轴力,桩身倾角越大,轴力沿深度衰减得越快,桩长径比越大,轴力沿深度衰减得也越快;斜桩桩身最大弯矩随桩身倾角及长径比的增加而增加,最大弯矩出现的深度与桩身倾角无关,只与长径比相关;不论桩身倾角及长径比的大小,斜桩桩身最大剪力均出现在桩顶截面处,桩身最大剪力随着桩身倾角的增加而增大;桩身倾角越大,斜桩最大摩阻力越大,长径比越大,斜桩最大摩阻力越小,斜桩最大摩阻力出现在桩顶下1/4～1/5桩长处;斜桩端阻比随着桩顶竖向荷载的增加而增大,随着桩身倾角及长径比的增加而减小。 相似文献
7.
非均质地基中群桩竖向荷载沉降关系分析 总被引：2，自引：0，他引：2
运用剪切位移法计算了桩轴向荷载传递因子。对于桩端采用线性的荷载传递函数,推导了基于弹塑性模型的单桩竖向荷载沉降的解析解。分析过程中考虑了土体强度沿深度线性变化的特性和桩土间的滑移现象,因此更符合大部分土体的实际性状。在此基础上,建立了考虑桩土滑移的桩-桩相互作用系数的计算公式,并将上述方法应用于群桩的分析,获得了群桩的荷载沉降特性。该分析方法克服了目前应用较多的弹性理论方法夸大桩土相互作用的缺点,单桩和群桩的荷载沉降曲线的分析结果和实测数据吻合,证明了该方法的合理性。 相似文献
8.
采用双曲线模型模拟桩土界面上的力学行为,利用剪切位移法反映剪应力在土层中的传递,考虑群桩之间的相互作用,建立了热?力耦合作用下能量桩群桩基础工作特性的简化分析方法。该方法能反映桩土界面上的非线性、桩顶的约束条件和能量桩位置的影响,可直接计算所有桩的位移和轴力。与现有方法相比,计算得到的双桩相互作用因子更加合理。通过与文献中试验数据的对比表明,若只有局部桩经历温度变化,能量桩运行过程中各桩之间存在差异变形,基础出现倾斜,桩顶荷载发生重分布。所建立方法计算方便,能合理模拟能量桩群桩基础的主要工作特性,可用于大规模能量桩群桩基础的设计计算。 相似文献
9.
A new approach to estimate shaft capacity of bored piles in sandy soils, based on numerical analysis, is presented. The topic is relevant as current design methods often largely underestimate the shaft capacity of piles in sands, thus resulting in an over-conservative design. The proposed approach is based on explicitly modelling the thin cylinder of soil surrounding the pile, where strain localization concentrates (shear band), and on the fundamental mechanic behaviour of sandy soils (e.g. dilatancy, softening). This approach is both simple and easy to apply. Results of a broad parametric study involving axially loaded single piles embedded in different sandy soils are presented, highlighting that relative density and grain size distribution mainly affect the shaft capacity. The capability of the procedure to predict shaft friction is checked against data from a well-documented full-scale axial load test on instrumented pile. Some suggestions for calibration and application of the method are also reported. 相似文献
10.
A method for predicting the maximum mobilized side resistance and unit shaft resistance-displacement curves (load transfer functions) on piles in clay is described. The method was derived using a numerical solution to model pile installation effects and a finite element scheme to model pile loading. Results of three well-documented pile load tests on steel piles were used to develop intermediate steps and final solutions, and the method was verified by comparing predicted results to two other load tests. An expression is proposed to represent load transfer functins for use by practitioners for the design of bridge and other foundations in clay. 相似文献
11.
超长灌注桩桩-土界面剪切模型及其有限元模拟 总被引：1，自引：0，他引：1
由于超长灌注桩为摩擦型桩,建立合适的桩-土界面剪切模型将成为合理且有效地模拟分析其承载变形特性的关键。基于超长灌注桩桩侧摩阻力? 随桩-土相对位移w发挥性状,将? - w关系定义为硬化和软化两种类型,进而将桩侧摩阻力发挥模式分为全硬化模式、全软化模式和混合模式。建立超长灌注桩桩-土界面剪切硬化模型和软化模型,运用ABAQUS二次开发子程序FRIC将建立的剪切模型嵌入有限元,实现剪切模型的有限元模拟,单桩算例表明,剪切模型在ABAQUS中实现是成功的。运用建立的桩-土界面剪切模型对现场试验试桩进行有限元模拟,模拟结果与实测结果较为吻合,表明所建立的桩-土界面剪切模型及其有限元模拟对于超长灌注桩承载变形计算具有合理性和可行性。 相似文献
12.
Rodrigo Salgado 《国际地质力学数值与分析法杂志》2011,35(15):1605-1635
In recent years, pile jacking has become a viable alternative installation method for displacement piles. Pile jacking produces minimal noise, vibration and air pollution during installation. In addition, it is possible, at the end of jacking, to have a good estimate of the ultimate static capacity of the pile. In this paper, the shaft resistance of piles jacked into sand is studied using one‐dimensional finite element analysis. The finite element simulations, using a two‐surface plasticity model, demonstrate the effects of relative density and confinement on the unit shaft resistance of piles jacked in sand. The impact of the number of jacking strokes on the unit shaft capacity is also assessed. Based on the numerical results, we developed equations for shaft resistance quantifying the effects of relative density, initial confinement and number of jacking strokes. Predictions using these equations are compared with data obtained from centrifuge tests and field tests. Copyright © 2010 John Wiley & Sons, Ltd. 相似文献
13.
Satyendra Mittal B. Ganjoo Sunny Shekhar 《Geotechnical and Geological Engineering》2010,28(5):717-725
The screw anchor piles are installed in ground by screwing which is done with the help of torque motors. In this paper, the
lateral load capacity of screw anchor piles is examined through an experimental investigation carried on model piles embedded
in dry sand. The tests were carried on screw anchor piles with different number of helices provided in continuation. Lateral
loads were applied at different height above the soil surface. The embedment length of screw anchor piles was also varied
to study the behaviour of screw anchor piles under lateral loads. Some tests were conducted on plain shaft pile to compare
the lateral load capacity of screw anchor piles with that of plain shaft piles. An empirical equation for computation of lateral
loads has been developed considering lateral resistance, bearing resistance, uplift resistance and lateral resistance offered
by soil in pile on the basis of experimental results. A theoretical model for predicting lateral load capacity of screw anchor
piles in dry sand, consistent with the experimental findings has been developed in this study. 相似文献
14.
考虑沉桩效应对桩周土体力学特性的影响,采用指数函数型荷载传递曲线分别建立了静压桩的桩侧和桩端荷载传递模型。在此基础上,根据群桩加载过程中桩周土体的变形模式,基于荷载传递法描述桩-土界面的非线性行为,采用剪切位移法考虑群桩之间的相互作用,提出了考虑沉桩效应的群桩非线性荷载-沉降混合计算方法。通过开展离心模型试验对该计算方法解答进行了验证,研究了沉桩效应和桩-土界面非线性特征对群桩承载特性的影响。研究结果表明,沉桩效应对桩周土体起到挤密作用,使得桩周土体的强度和刚度增大,从而提高了群桩的承载特性。群桩加载过程中桩-土界面刚度随沉降变形而逐渐减小,使得群桩荷载-沉降曲线呈现出明显的非线性特征。 相似文献
15.
既有建筑下增层开挖对已有桩基础的影响不同于基坑开挖对坑内桩基的影响。基于工程实例验证的有限元参数,用硬化土弹塑性模型模拟土体,用接触面单元模拟桩土相互作用,建立了桩筏基础-地基-增层开挖三维有限元模型,对增层开挖后群桩基础的竖向承载性状进行研究。分析了桩顶刚度、桩身轴力、桩侧摩阻力、桩端阻比以及土体回弹的变化规律,并研究了不同桩端土体刚度和增层开挖深度对这些参数的影响。结果表明,增层开挖后群桩中不同基桩表现出不同的承载性状,增大桩端土体刚度可明显提高单桩承载力和端阻比临界值;随着增层开挖深度的增加,侧阻和端阻的发挥程度也随之提高。研究结果有望为地下室增层开挖施工中的结构托换变形控制和补桩设计提供依据。 相似文献
16.
17.
A new and simple approach is presented to analyze the elastic–plastic behavior of a single pile in layered soils using two models. One model adopts a hyperbolic approach to describe the nonlinear relationship between the shaft shear stresses and the displacement surrounding the pile shaft, and the other model uses a bilinear hardening model to simulate the relationship between the settlement and the mobilized load at the pile end. Furthermore, the interaction between identical piles including the pile shaft and the base interaction in multilayered soils is analyzed. Comparisons of the load–settlement responses for two well-instrumented field tests in multilayered soils are given to demonstrate the effectiveness and accuracy of the proposed simple method. This present paper enables a quick estimate of the settlement of a single pile and a pile group embedded in layered soils, resulting in savings in time and cost. 相似文献
18.
桩-土相互作用问题是岩土工程桩基础问题的关键点与难点,目前针对桩身在循环温度荷载与上覆结构荷载双重作用下的能源桩承载特性研究较少。在传统理想弹塑性模型及双曲线模型的基础上,采用分段非线性的方法对桩-土荷载传递骨干曲线进行了修正,并基于Masing’s循环准则,提出了适用于能源桩的桩-土荷载传递模型。利用改进的桩-土荷载传递模型对能源桩承载特性进行数值分析,着重研究了桩-土荷载传递参数比R对能源桩受力情况的影响。此外,为了探究在上覆结构荷载及循环温度荷载双重作用下,能源桩与周围土体之间的真实荷载传递关系及其结构热力学特性,开展了针对能源桩与周围土体之间相互作用问题的室内模型试验,监测了其桩身轴向应力及侧摩阻力随温度及深度变化的趋势,并与基于改进荷载传递模型的数值计算结果进行了对比。室内模型试验监测及数值计算结果显示：能源桩在上覆结构荷载及温度循环荷载双重作用下,其受力行为受改进的桩-土荷载传递循环曲线控制;基于改进的桩-土荷载传递循环曲线而建立的数值模型计算结果与试验结果基本吻合,改进的桩-土荷载传递模型能够较好发地反映能源桩实际的承载特性。 相似文献
19.
Jay X. Wang 《Geomechanics and Geoengineering》2017,12(2):86-106
In this paper research was presented on the development of a growth-rate-dependent model for pile set-up prediction using the restrike and static/statnamic load testing data collected from different projects. The data included: a) restrike records from ninety-five production piles and restrike and load test results of nine instrumented piles driven in soft clays from the relocation project of Highway No. 1 in Louisiana (LA-1); and b) restrike and static load testing data of five fully instrumented square PPC piles driven at four different bridge sites in various soil layers from sands to clays in Florida. Research effort was focused on the prediction of the ultimate shaft resistances with pile set-up formulated using the pile resistance growth rate-dependent model. The timeframe of interest was studied for a practical set-up magnitude such as 90% of the ultimate shaft resistance (Q90). As an application of the rate-dependent model, it was found that piles at the LA-1 relocation project, in general, reached about 95% of the ultimate shaft resistances at the time of 2 weeks after pile installation. The strategy of incorporation of pile set-up in adjusting pile driving criteria or/and design during pile construction, such as the experience-based plan of a two-week waiting period adopted by Louisiana DOTD, was investigated and justified. 相似文献
20.
分层土中群桩水平动力阻抗的改进计算 总被引：1，自引：0，他引：1
采用动力Winkler地基梁模型,建立了主动桩和被动桩的简化解析运动方程,考虑地基土的分层特性、桩身剪切变形和转动惯量,提出了计算分层地基中单桩和群桩动力阻抗的改进计算方法,并与已有文献的计算结果进行了对比,结果表明：改进方法的计算结果与现场实测更接近。在低频段,改进方法的计算结果与已有文献结果较一致,但随着桩身剪切模量的减小,两者差异增大。差异主要是由考虑桩身剪切变形和转动惯量引起的,且前者影响较大,在低频段差异亦十分明显,而后者影响较小,在群桩阻抗峰值区域和高频段差异明显,需考虑桩身转动惯量的影响。 相似文献