首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献，搜索用时 689 毫秒
1.
This paper investigates the postcyclic behavior of low-plasticity silt with excess pore pressure ratio (Ru) less than 1. The testing specimens were prepared from Mississippi River Valley (MRV) silt. Full and no reconsolidation were allowed after specimens were subjected to various excess pore pressure ratios due to cyclic loading in a cyclic triaxial cell, and then monotonic shear tests were conducted. The effect of the Ru on shear strength and stiffness at small and large deformation was investigated. It was found that a Ru greater than 0.70 is a prerequisite of large increase in volumetric strain and undrained shear strength for specimens with full reconsolidation. In contrast, a significant decrease in yield shear strength and initial stiffness was noted for specimens without reconsolidation. In comparison to published data for sands, the silt experienced significant volumetric strain due to reconsolidation at lower Ru, indicating that the specimen fabric was modified or strained at lower Ru.  相似文献   

2.
The liquefaction behavior and cyclic resistance ratio (CRR) of reconstituted samples of non-plastic silt and sandy silts with 50% and 75% silt content are examined using constant-volume cyclic and monotonic ring shear tests along with bender element shear wave velocity (Vs) measurements. Liquefaction occurred at excess pore water pressure ratios (ru) between 0.6 and 0.7 associated with cumulative cyclic shear strains (γ) of 4% to 7%, after which cyclic liquefaction ensued with very large shear strains and excess pore water pressure ratio (ru>0.8). The cyclic ring shear tests demonstrate that cyclic resistance ratio of silt and sandy silts decreases with increasing void ratio, or with decreasing silt content at a certain void ratio. The results also show good agreement with those from cyclic direct simple shear tests on silts and sandy silts. A unique correlation is developed for estimating CRR of silts and sandy silts (with more than 50% silt content) from stress-normalized shear wave velocity measurements (Vs1) with negligible effect of silt content. The results indicate that the existing CRR–Vs1 correlations would underestimate the liquefaction resistance of silts and sandy silt soils.  相似文献   

3.
This paper investigates the cyclic and post-cyclic shear behavior of low-plasticity silt and the impact of additional clay content. Bentonite clay was added to the low-plasticity Mississippi River Valley (MRV) silt (PI=6) to increase the clay content of the soil. A series of triaxial tests were conducted in the laboratory to examine the shear and pore pressure behavior during and after cyclic loading. As the bentonite content in the reconstituted specimens increased, the excess pore pressure developed at a slower rate and the total excess pore pressure decreased at the end of cyclic loading. In contrast to the MRV silt, the specimens modified with bentonite experienced cyclic softening rather than initial flow liquefaction. The cyclic shear strength increased with an increase in bentonite content. The post-cyclic reconsolidation behavior was a similar to a virgin compression process, and not recompression. Adding bentonite to the MRV silt results in changes in permeability, compressibility, undrained shear strength, and initial stiffness. Additionally, the cyclic loading had a marked effect on the shear behavior of low-plasticity soil with a PI<6, but not noticeable with a PI>6. This study suggests that the behavior of the Mississippi River Valley silt changes from contractive sand-like material to clay-like behavior at a PI≈6 due to the addition of clay.  相似文献   

4.
A series of cyclic triaxial tests on clayey sands was carried out and attempts were made to evaluate the strain dependency of shear modulus and damping. Strain dependencies of shear modulus and damping were simply modeled. It was shown that the change in the effective confining stress with loading cycles in the undrained shear test needed to be considered particularly in the large strain range. The consideration could be made by normalizing G with G′0=AF(e)(σ′m/σmr)n, the initial shear modulus for the effective confining stress of that particular loading cycle, instead of using G0. G/G′0 was expressed by a function of γ as G/G′0=1/(1+bgγ) which was almost stress level independent for clayey sands used in this study. The damping ratio was not much affected by the confining stress. The strain dependency of the damping ratio was modeled by h=ahγ/(1+bhγ). Effects of load irregularity on the shear modulus were also investigated. The excess pore pressure and the residual strain were generated especially when the major peaks in the irregular loading were applied to the specimen. However, G/G′0 for the irregular loading could be represented reasonably well by the average curve for the uniform cyclic loading, if the excess pore water pressure and the residual strain were taken into account.  相似文献   

5.
Pore water pressure generation during earthquake shaking initiates liquefaction and affects the shear strength, shear stiffness, deformation, and settlement characteristics of soil deposits. The effect of plastic fines (kaolinite) on pore pressure generation in saturated sands was studied through strain-controlled cyclic triaxial tests. In addition to pore pressure generation, this experimental study also focused on evaluating the threshold shear strain for pore pressure generation and the volumetric compressibility of specimens during pore pressure dissipation. The results reveal that specimens having up to 20% plastic fines content generated larger values of pore water pressure than clean sand specimens. At 30% fines content, the excess pore water pressure decreased below that of clean sand. The threshold shear strain, which indicates the strain level above which pore pressures begin to generate, was assessed for different kaolinite–sand mixtures. The threshold shear strain was similar for 0–20% fines (γt0.006–0.008%), but increased to about 0.025% for 30% fines. The volumetric compressibility, measured after pore pressure generation, was similar for all specimens. The transition of behavior at fines contents between 20% and 30% can be attributed to a change in the soil structure from one dominated by sand grains to one dominated by fines.  相似文献   

6.
To identify the effect of non-plastic silt on the cyclic behavior of sand–silt mixtures, total sixty undrained cyclic triaxial stress-control tests were carried out on sand–silt mixtures. These tests were conducted on specimens of size 71 mm diameter and 142 mm height with a frequency of 1 Hz. Specimens were prepared at a constant relative density and constant density approach. The effect of relative density, confining pressure as well as magnitude of cyclic loading was also studied. For a constant relative density (Dr=60%) the effect of limiting silt content, pore pressure response and cyclic strength was observed. The rate of generation of excess pore water pressure with respect to cycles of loading was found to initially increase with increase in silt content till the limiting silt content and thereafter it reverses its trend when the specimens were tested at a constant relative density. The cyclic resistance behavior was observed to be just opposite to the pore pressure response. Permeability, CRR and secant shear modulus decreased till limiting silt content; after that they became constant with increasing silt content.  相似文献   

7.
Laboratory cyclic triaxial tests were performed to investigate the effect of fine content on the pore pressure generation in sand. Strain-controlled, consolidated undrained tests have been performed with a cyclic shear strain range of 0·015-1·5%. These tests were carried to 1000 cycles or to initial liquefaction, which ever occurred first. Triaxial tests were performed on pure sand silt specimens and specimens with silt additions of 10, 20, 30, and 60% by weight. Two types of silt, a non-plastic silt and a low plasticity silt (PI 10) were used as control materials. The main parameters varied in this study were the amount of silt, the plasticity index of silt, and the void ratio where the observed parameter was the pore pressure generation. For all silt contents, silt plasticity and the number of loading cycles have no significant effect at strain levels below 0·01%. Therefore, threshold strain for silty sands have approximately the same value as sands. For both non-plastic and low plasticity silts, there is a significant increase in the generated pore pressure at high strain levels.  相似文献   

8.
主应力轴持续旋转条件下饱和松砂的振动孔隙水压力特性   总被引：2，自引：0，他引：2  
利用新研制的“土工静力-动力液压三轴-扭剪多功能剪切仪”,针对福建标准松砂,在三向非均等固结条件下,进行了能够模拟海洋波浪荷载作用下主应力轴连续旋转的循环耦合剪切试验。通过试验着重探讨了初始主应力方向、振动过程中主应力方向连续变化对不排水条件下砂土的振动孔隙水压力增长特性的影响。实验研究表明:在振动过程中主应力轴连续旋转的条件下,初始主应力方向对砂土的动孔压比与振次比之间关系具有显著的影响,随着初始大主应力与竖向之间夹角的增大,动孔压比的增长速度明显加快,具有较好的规律性;归一化孔压比与广义剪应变之间的关系基本上与初始主应力方向角和振动剪应力幅值无关。  相似文献   

9.
Softening and strength loss of sands with increasing excess pore water pressure under repeated loads is well-known. However, extensive damage to the built environment also occurs at the sites underlain by fine grained soils during seismic shaking. The primary objective of this study is to investigate the factors affecting cyclic behavior of saturated low-plastic silt through laboratory testing. For this purpose, an extensive laboratory testing program including conventional monotonic and cyclic triaxial tests was carried out over reconstituted silt samples. The effects of the inherent soil properties and the effects of loading characteristics on the cyclic response of saturated low-plastic reconstituted silt samples were examined separately. Based on the test results, a model was introduced to estimate the effect of initial shear stress on the cyclic response. Besides, liquefaction susceptibility of the samples was examined via current liquefaction susceptibility criteria.  相似文献   

10.
In this study the stress–strain characteristics of sand-ground rubber mixtures are investigated in the sandlike zone,at different confining pressures,using hollow cylinder specimens subjected to torsional monotonic and cyclic loading.Under monotonic loading a mixture of sand-ground rubber with 10% and 25% rubber content show more contraction behaviour than that observed in a pure sand specimen.Phase transformation point in these mixtures are located on a larger shear strain.As expected,the shear strength of specimens decreases with increase of ground rubber content.However,with increasing of effective confining pressure,the loss in shear strength of the mixture is decreased.In addition,a mixture with 25% ground rubber shows a smaller loss in shear strength compared to a mixture with 10% ground rubber mixture.Under cyclic loading mixtures with 10% and 25% ground rubber have similar liquefaction resistance,especially at confining pressures of 110 k Pa and 260 k Pa.Therefore,by using of the mixture with 25% ground rubber,a larger volume of scrap tires could be recycled.The addition of ground rubber to sand would affect the shear strain variation and excess pore water pressure trends,and this effect was further intensified with increasing ground rubber percentage.  相似文献   

11.
The paper provides insight into factors affecting the prediction of seismic pore-water pressure build up in clean sands and sand–silt mixtures for modeling purposes. Laboratory pore pressure measurements were conducted using stress-controlled undrained cyclic simple shear (CSS) tests carried out on both reconstituted and undisturbed specimens of silty sands under different initial conditions (density state, effective vertical stress, initial fabric and fines content). Test results were interpreted by using a damage concept-based model which is actually implemented for clean sands in non-linear time domain site response analysis codes. In the present work, such a model was properly modified for sands having fines contents higher than 35%. The general applicability of the modified procedure for predicting pore water pressure response of silty sands under irregular shear stress loading using data from stress-controlled CSS tests was also verified and all factors affecting calibration parameters of the model were throughly analyzed.  相似文献   

12.
Nonlinear elastic behavior of fiber-reinforced soil under cyclic loading   总被引：5，自引：0，他引：5  
Experimental investigations and modeling of nonlinear elasticity of fiber-reinforced soil under cyclic loading at small strain are conducted in this paper. The investigations include three aspects. First, cyclic shear tests are conducted using conventional triaxial apparatus. Twenty-seven specimens with three different fiber contents are employed to conduct triaxial cyclic shear tests under different confining pressure and loading repetition. Effects of geofiber, confining pressure and loading repetition on elastic shear modulus of reinforced soil are studied and analyzed. Second, a hyperbolic function is introduced to describe the nonlinear stress–strain skeletal curve under cyclic loading. Nonlinear elastic modulus is expressed as a function of shear strain and two variables A and B that are related to the initial tangential modulus and ultimate cyclic loading stress, respectively. In the present paper, variables A and B both are further assumed to be functions of geofiber content, confining pressure and loading repetition. Finally, eight constitutive coefficients of the nonlinear elastic model are calibrated using stress–strain curves from cyclic triaxial shear tests. The calibration of parameters is conducted using the technique of the linear regression for multiple variables. Impacts and effects of geofiber, confining pressure and loading repetitions on soil nonlinear elastic behavior are discussed.  相似文献   

13.
The November 3, 2002 Denali-Alaska earthquake (Mw=7.9) caused significant liquefaction associated damage to various infrastructure built on fine-grained soils. The seismic response, liquefaction potential, and excess pore pressure generation of soils in cold regions, especially those of fine-grained nature, have not been studied thoroughly and therefore are not well-understood. This paper presents results from an extensive laboratory study on the characteristics of excess pore pressure generation and liquefaction potential of fine-grained soils. Laboratory-constituted soils specimens were tested in four categories: (1) tests on specimens subjected to no thermal conditioning or freeze–thaw cycles; (2) tests on specimens conditioned at 24, 5, 1, 0.5, and −0.2 °C; (3) tests on specimens subjected to 1–4 freeze–thaw cycles; and (4) tests on specimens conditioned at near-freezing temperatures of 0.5 and −0.2 °C through different freeze–thaw paths. Strain-controlled, undrained, cyclic triaxial tests were performed at shear strain levels of 0.005–0.8%. Specimens conditioned at different temperatures were found to generate significantly different pore pressures with cyclic loading. The excess pore pressure generation at near or slightly below freezing was found to change dramatically. A transitional change in the dynamic soil behavior, attributed to unfrozen- or frozen-dominant pore water, was discovered. The threshold shear strain was also found to be influenced by the temperature. Subjecting the soil specimens to 1, 2 and 4 freeze–thaw cycles caused a reduction in excess pore pressure generation and slight change in the threshold shear strain. The temperature conditioning path to reach the target temperature was found to be important on the development of excess pore pressure at near and slightly below-freezing temperatures.  相似文献   

14.
During earthquake events, low-plasticity silt undergoes a reduction in shear strength and stiffness due to development of excess pore pressure induced by cyclic loading. With reconsolidation, during which process excess pore pressure is dissipated, the shear strength and stiffness can be regained. However, due to the low permeability of silts (compared to sands), the dissipation of excess pore pressure and the reconsolidation of low-plasticity silt takes much more time. This paper investigates the postliquefaction shear behavior of Mississippi River Valley (MRV) silt at various degrees of reconsolidation using triaxial tests. Test results indicate that there was a steady increase, in shear strength and stiffness, at both large and small deformations, with increase in the degree of reconsolidation. The postliquefaction silt showed the effect of the apparent OCR, which had a close effect on postcyclic shear behavior as did the OCR on the static behavior. The critical state lines of MRV silt were different for pre- and post-liquefaction conditions.  相似文献   

15.
复杂应力条件下饱和松砂单调与循环剪切特性的比较研究   总被引：4，自引：0，他引：4  
本文利用大连理工大学新引进与开发的“土工静力-动力液压-三轴扭转多功能剪切仪”,针对福建标准砂,在不排水条件下同时进行了单调剪切试验与循环剪切试验,进而对其进行了对比分析。通过比较表明,应力-应变关系的应变软化和硬化特性与流滑变形和循环流动特性密切相关,当循环剪切应力水平高于单调剪切过程中应变软化阶段最小强度时将会发生流滑变形。无论在单调剪切中,还是在循环剪切中,稳定状态时的有效偏应力比随着大主应力方向与竖向之间夹角的增大而减小,在中主应力系数相同的条件下,循环剪切中呈现显著剪胀时的有效偏应力比和最终稳定状态时的有效偏应力比峰值分别与单调剪切中达到相变状态时的有效偏应力比和最终稳定有效偏应力比基本上一致。然而不排水条件下单调与循环剪切过程中孔隙水压力的增长特性却并不相同,循环剪切中的最大孔隙水压力随着初始主应力方向角的增大而减小,单调剪切中的最大孔隙水压力却随着主应力方向角的增大而增大。  相似文献   

16.
针对荆江大堤江陵段下伏地层广泛分布的饱和粉细砂,参照原位试验成果重塑粉细砂试样,按估算的固结应力比(Kc约为1.6)对试样动剪模量、阻尼比及总应力动强度进行测试,结果表明:(1)试样应力-应变骨干曲线与Hardin-Drnevich双曲线模型假设高度吻合,Hardin公式可很好地拟合动模量/阻尼比与动应变的关系。在研究试样密实度范围内,最大动模量随围压和密实度的增加而增加,但围压对动模量的敏感性更高,且相同围压下动剪模量比与动应变关系曲线近乎重合。围压增大或密实度升高均会引起阻尼比的降低,1%应变对应的阻尼比分布在0.15~0.21之间;(2)偏压状态下以累积轴向应变5%作为液化判别标准进行抗液化强度试验,随特征振次及测试围压的增大,液化动剪应力比相应减小,试样振动孔压比最高仅能达到0.8~0.9;(3)由总应力法求取的动内摩擦角与黏聚力均随设定特征振次的增加而下降,且内聚力并非约等于0,表明动力作用下该试样具有一定的黏滞性。  相似文献   

17.
黄河三角洲粉土液化的试验研究   总被引：2，自引：0，他引：2  
在野外自然地理和地质调查的基础上，以黄河地区可液化场地粉土为研究对象，利用室内动三轴和振动柱试验进行测定，分析了动荷载作用下粉土的动应力应变关系并模拟了地震荷载作用下粉土的孔压响应及抗液化强度，得出了液化破坏标准，提出了原状粉土的振动孔压上升模型。对试验结果进行分析发现，随着粘粒含量的增加，粉砂、粉土、粉质粘土、粘土达到相同剪应变所需的动剪应力也依次增加；粉土孔压比0．68、粉砂土孔压比0．87作为液化破坏开始的标志；粉土发生液化所需的循环应力比大于砂土。这些研究为以后建立适合本地区的饱和地基土地震破坏判别方法提供了参数和依据。  相似文献   

18.
The paper presents a mathematical model for the deformation of soil under irregular cyclic loading in the simple-shear conditions. The model includes the possible change in the effective pressure in saturated soil due to the cyclic shearing, the reciprocal influence of the effective pressure on the response of the soil to the shear loading, and the pore pressure dissipation due to the seepage of the pore fluid. The hysteresis curves for the strain–stress relationship are constructed in such a way that they produce both the required backbone curve and the required damping ratio as functions of the strain amplitude. At the same time, the approach enables the constitutive functions involved in the model to be specified in various ways depending on the soil under study. The constitutive functions can be calibrated independently of each other from the conventional cyclic shear tests. The constitutive model is incorporated in the boundary value problem for the dynamic site response analysis of level ground. A numerical solution is presented for the dynamic deformation and liquefaction of soil at the Port Island site during the 1995 Hyogoken-Nambu earthquake.  相似文献   

19.
Stiffness degradation of natural fine grained soils during cyclic loading   总被引：5，自引：0，他引：5  
Cyclic behavior of natural fine grained soils under a broad range of strains were investigated considering the effects of plasticity index and changes in confining pressures based on cyclic triaxial tests. A total of 98 stress controlled cyclic triaxial tests were conducted on normally consolidated and slightly overconsolidated samples. The investigation was divided into two parts. The first part consists of stress controlled cyclic triaxial tests under different stress amplitudes that were conducted to estimate the modulus reduction and the thresholds between nonlinear elastic, elasto-plastic and viscoplastic behavior. The second part involves the investigation of the undrained stress–strain behavior of fine grained soils under irregular cyclic loadings. The results showed that the elastic threshold is approximately equal to 90% of Gmax. Another transition point was defined as the flow threshold where the value of tangent of shear modulus ratio changes for the second time. Simple empirical relationships to estimate the dynamic shear modulus and damping ratio was formulated and compared with the similar empirical relationships proposed in the literature. The results provide useful guidelines for preliminary estimation of dynamic shear modulus and damping ratio values for fine grained soils based on laboratory tests.  相似文献   

20.
Small strain shear modulus Gmax is an essential parameter in soil dynamics, and it is usually estimated based on the Hardin and Richart equation. However, many previous researches on sands have indicated that the Hardin and Richart equation does not consider the influences of cyclic loading history on Gmax. In this paper, effects of cyclic loading history on Gmax of saturated clays under undrained conditions are studied using a combination device of piezoelectric-ceramic bender element system and cyclic triaxial apparatus. The dynamic pre-loading includes both relatively high amplitudes of cyclic stresses and cyclic strains. Gmax without cyclic loading history is also investigated for the comparison purpose. Test results show that, at the same effective stress, both cyclic strain history and cyclic stress history will induce reduction of Gmax compared to the corresponding Gmax values with non-cyclic loading effects. In strain-controlled tests, the reduction of Gmax is slight and relatively stable; while in stress-controlled tests, the reduction of Gmax increases suddenly and remarkably when the effective stresses degrade to a certain degree. The comparison between double amplitude axial strain and residual excess pore water pressure behaviors show that the remarkable reduction of Gmax can demonstrate the cyclic failure of saturated clays.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号