首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献，搜索用时 703 毫秒
1.
Naturally occurring radon in ground water can potentially be used as an in situ partitioning tracer to characterize dense nonaqueous phase liquid (DNAPL) saturations. The static method involves comparing radon concentrations in water samples from DNAPL-contaminated and noncontaminated portions of an aquifer, while the push-pull method involves the injection (push) and extraction (pull) of a radon-free test solution from a single well. In the presence of DNAPL, radon concentrations during the pull phase are retarded, with retardation manifested in greater dispersion of radon concentrations relative to a conservative tracer. The utility of these methods was investigated in the laboratory using a physical aquifer model (PAM). Static and push-pull tests were performed before and after contamination of the PAM sediment pack with trichloroethene (TCE), and after alcohol cosolvent flushing and pump-and-treat remediation. Numerical simulations were used to estimate the retardation factor for radon in push-pull tests. Radon partitioning was observed in static and push-pull tests conducted after TCE contamination. Calculated TCE saturations ranged up to 1.4% (static test) and 14.1% (push-pull test). Post-remediation tests showed decreases in TCE saturations. The results show that radon is sensitive to changes in DNAPL saturation in space and time. However, the methods are sensitive to DNAPL saturation heterogeneity, test location, sample size, and test design. The influence of these factors on test results, as well as the apparent overestimation of the retardation factor in push-pull tests, warrant further investigation.  相似文献   

2.
The use of surfactant solutions for the in situ recovery of residual NAPL in aquifers is increasingly considered as a viable remediation technique. The injection of a few pore volumes of high concentration surfactant solutions can mobilize most of the residual NAPL contacted by the solutions. However, the washing solutions'physico-chemical properties (low density and high viscosity), combined with the natural porous media heterogeneity, can prevent a good sweep of the entire contaminated volume. From the petroleum industry, it is well-known that polymer solutions can be injected following a surfactant solution slug to act as a mobility buffer and increase the overall sweep efficiency. The objective of our laboratory study is first to select and characterize polymers that would be suitable for aquifer restoration. Our experiments showed that among several polymers, xanthan gum solution rheology was made in order to predict shear rates, xanthan gum concentrations, salinity, and temperature effects on solution viscosity. The second set of experiments were made with a sand box which was designed to reproduce a simple heterogeneous media consisting of layers of sand with different permeability. These tests illustrate the xanthan gum solution's ability to increase surfactant solution's sweep efficiency and limit viscous fingering. The tests established that: (1) the injection of xanthan solution behind a surfactant solution slug decreases fluid velocity in high permeability layers and increases it in low-permeability ones, thus increasing the sweep efficiency (2) xanthan solutions eliminate viscous fingering at the polymer/surfactant solution front; (3) a xanthan solution preflush is desirable to limit surfactant solution mobility and prevent surfactant adsorption on solids; and (4) depending on site heterogeneity injection strategies should be applied to limit overriding by low-density surfactant solution.  相似文献   

3.
Contamination from the use of chlorinated solvents, often classified as dense nonaqueous phase liquids (DNAPLs) when in an undissolved state, represents an environmental challenge with global implications. Mass-transfer limitations due to rate-limited dissolution can lead to long-term aquifer persistence for even small volumetric fractions. The identification of DNAPL source zones located beneath the water table is critical to ultimately achieve site remediation and aquifer restoration. This paper provides a comparison of the advantages and disadvantages of many of the methods being used for detecting and delineating DNAPL contaminant source zones. The objective is to determine which options are best to pursue based on site characteristics, method performance, and method costs. DNAPL characterization methods are grouped into approaches, which include site preparation, characterization, and data-processing activities necessary to design an effective remediation system. We compare the different approaches based on the level of chemical and hydrogeologic resolution, and the need for additional data requirements. Our findings can be used to assist with selection of appropriate site remediation management options.  相似文献   

4.
Plume containment using pump-and-treat (PAT) technology continues to be a popular remediation technique for sites with extensive groundwater contamination. As such, optimization of PAT systems, where cost is minimized subject to various remediation constraints, is the focus of an important and growing body of research. While previous pump-and-treat optimization (PATO) studies have used discretized (finite element or finite difference) flow models, the present study examines the use of analytic element method (AEM) flow models. In a series of numerical experiments, two PATO problems adapted from the literature are optimized using a multi-algorithmic optimization software package coupled with an AEM flow model. The experiments apply several different optimization algorithms and explore the use of various pump-and-treat cost and constraint formulations. The results demonstrate that AEM models can be used to optimize the number, locations and pumping rates of wells in a pump-and-treat containment system. Furthermore, the results illustrate that a total outflux constraint placed along the plume boundary can be used to enforce plume containment. Such constraints are shown to be efficient and reliable alternatives to conventional particle tracking and gradient control techniques. Finally, the particle swarm optimization (PSO) technique is identified as an effective algorithm for solving pump-and-treat optimization problems. A parallel version of the PSO algorithm is shown to have linear speedup, suggesting that the algorithm is suitable for application to problems that are computationally demanding and involve large numbers of wells.  相似文献   

5.
This paper investigates numerical optimization of dense nonaqueous phase liquid (DNAPL) site remediation design considering effects of prediction and measurement uncertainty. Results are presented for a hypothetical problem involving remediation using thermal source reduction (TSR) and bioremediation with electron donor (ED) injection. Pump-and-treat is utilized as a backup measure if compliance criteria are not met. Remediation system design variables are optimized to minimize expected net present value (ENPV) cost. Adaptive criteria are assumed for real-time control of TSR and ED duration. Source zone dissolved concentration data enabled more reliable and lower cost operation of TSR than soil concentration data, but using both soil and dissolved data improved results sufficiently to more than offset the additional cost. Decisions to terminate remediation and monitoring or to initiate pump-and-treat are complicated by measurement noise. Simultaneous optimization of monitoring frequency, averaging period, and lookback periods to confirm decisions, in addition to remediation design variables, reduced ENPV cost. Results indicate that remediation design under conditions of uncertainty is affected by subtle interactions and tradeoffs between design variables, compliance rules, site characteristics, and uncertainty in model predictions and monitoring data. Optimized designs yielded cost savings of up to approximately 50% compared with a nonoptimized design based on common engineering practices. Significant improvements in accuracy and reductions in cost were achieved by recalibrating the model to data collected during remediation and re-optimizing design variables. Repeating this process periodically is advisable to minimize total costs and maximize reliability.  相似文献   

6.
In situ bioreclamation is a proven technology that cost-effectively treats organic contamination in subsurface environments. As a remediation strategy, it reduces both the contamination dissolved in ground water, as well as residual soil-bound contamination.
To maximize biodegradation, the technology is applied after conducting laboratory studies. Application of the technology involves infiltrating necessary nutrients to the contaminated subsurface.
Results of a specific case study indicate excellent performance with rapid cleanup of petroleum hydrocarbon contamination from soils and ground water.
Costs associated with in situ bioreclamation technology showed a savings of approximately 50 percent over simple pump-and-treat technology. Time frame for cleanup was shown to be approximately 30 percent of the projected time frame of simple pump-and-treat technology.  相似文献   

7.
The release of stored dissolved contaminants from low permeability zones contributes to plume persistence beyond the time when dense nonaqueous phase liquid (DNAPL) has completely dissolved. This is fundamental to successfully meeting acceptable low concentrations in groundwater that are driven by site‐specific cleanup goals. The study goals were to assess the role of DNAPL entrapment morphology on mass storage and plume longevity. As controlled field studies are not feasible, two‐dimensional (2D) test tanks were used to quantify the significance of mass loading processes from source dissolution and stored mass rebound. A simple two‐layer soil domain representing a high permeable formation sand overlying a zone of lower permeability sand was used in the tests. DNAPL mass depletion through dissolution was monitored via X‐ray photon attenuation, and effluent samples were used to monitor the plume. These data enabled analysis of the DNAPL distribution, the dissolved plume, and the dissolved phase distribution within the low permeability layer. Tests in an intermediate tank showed that mass storage contributes substantially to plume longevity. Detectable effluent concentrations persisted long after DNAPL depletion. The small tank results indicated that the DNAPL morphology influenced the flow field and caused distinctive transport mechanisms contributing to mass storage. Zones of high DNAPL saturation at the interface between the low and high permeability layers exhibited flow bypassing and diffusion dominated transport into the low permeability layer. In the absence of a highly saturated DNAPL zone near the soil interface the contaminant penetrated deeper into the low permeability layer caused by a combination of advection and diffusion.  相似文献   

8.
The influence of aquifer property correlation on multiphase fluid migration, entrapment and recovery was explored by incorporating correlated and uncorrelated porosity, permeability, and capillary pressure-saturation (Pc-Sat) parameter fields in a cross-sectional numerical multiphase flow model. Comparison of two-dimensional entrapped organic saturation distributions for a simulated tetrachloroethylene (PCE) spill in ensembles of aquifer realizations suggests that the degree of spatial correlation in Pc-Sat parameters exerts a controlling influence on dense nonaqueous phase liquid (DNAPL) spreading and redistribution in saturated aquifers. The predicted evolution of DNAPL source zones and resultant remediation efficiency under surfactant enhanced aquifer remediation (SEAR) also appear to be strongly influenced by the spatial correlation of aquifer parameters and multiphase flow constitutive relationships. Results for a limited number of realizations selected from each ensemble showed that removal of 60% to 99% of entrapped PCE could reduce dissolved contaminant concentration and mass flux by approximately two orders of magnitude under natural gradient conditions. Aqueous phase contaminant mass flux did not vary uniformly as a function of % DNAPL removed, however, and notable differences in behavior were observed for models incorporating correlated versus uncorrelated Pc-Sat and permeability fields. Although these results must be confirmed through analysis of additional realizations, it is likely that similar or larger differences between correlated and uncorrelated system behavior will be observed in aquifers with greater spatially variability than that of the nonuniform, homogeneous sand aquifer studied here. Funding for this research was provided by the United States Environmental Protection Agency, Great Lakes and Mid-Atlantic Center for Hazardous Substance Research under Grant No. R-825540, the Michigan Department of Environmental Quality under Contract No. Y80011, and the Strategic Environmental Research and Development Program under Project No. CU-1293. The content of this publication does not necessarily represent the views of these agencies and has not been subject to agency review.  相似文献   

9.
Vapor extraction (soil venting) has been demonstrated to be a successful and cost-effective remediation technology for removing VOCs from the vadose (unsaturated) zone. However, in many cases, seasonal water table fluctuations, drawdown associated with pump-and-treat remediation techniques, and spills involving dense, non-aqueous phase liquids (DNAPLS) create contaminated soil below the water table. Vapor extraction alone is not considered to be an optimal remediation technology to address this type of contamination.
An innovative approach to saturated zone remediation is the use of sparging (injection) wells to inject a hydrocarbon-free gaseous medium (typically air) into the saturated zone below the areas of contamination. The contaminants dissolved in the ground water and sorbed onto soil particles partition into the advective air phase, effectively simulating an in situ air-stripping system. The stripped contaminants are transported in the gas phase to the vadose zone, within the radius of influence of a vapor extraction and vapor treatment system.
In situ air sparging is a complex multifluid phase process, which has been applied successfully in Europe since the mid-1980s. To date, site-specific pilot tests have been used to design air-sparging systems. Research is currently underway to develop better engineering design methodologies for the process. Major design parameters to be considered include contaminant type, gas injection pressures and flow rates, site geology, bubble size, injection interval (areal and vertical) and the equipment specifications. Correct design and operation of this technology has been demonstrated to achieve ground water cleanup of VOC contamination to low part-per-billion levels.  相似文献   

10.
Release of an estimated 150,000 gallons (568,000 L).of 1.2–dichloroethane (EDC) from a buried pipeline into a ditch and surrounding soil resulted in shallow subsurface contamination of a Gulf Coast site. Short-term remediation included removal of EDC DNAPI. (dense nonaqueous phase liquid) by dredging and vacuuming the ditch, and by dredging the river where the ditch discharged. EDC saturation in shallow impacted sediments located beneath the ditch was at or below residual saturation and these sediments were therefore left in place. The ditch was lined, backfilled, and capped. Long-term remediation includes EDC DNAPL recovery and hydraulic containment from the shallow zone with long-term monitoring of the shallow, intermediate, and deep (200 foot) aquifers. Ground water, DNAPL., and dissolved phase models were used to guide field investigations and the selection of an effective remedial action strategy. The DNAPL. modeling was conducted for a two-dimensional vertical cross section of the site, and included the three aquifers separated by two aquitards with microfractures. These aquitards were modeled using a dual porosity approach. Matrix and fracture properties of the aquitards used for DNAPL modeling were determined from small-scale laboratory properties. These properties were consistent with effective hydraulic conductivity determined from ground water flow modeling. A sensitivity analysis demonstrated that the vertical migration of EDC was attenuated by dissolution of EDC into the matrix of the upper aquitard. When the organic/water entry pressure of the aquitard matrix, or the solubility of EDC were decreased to unrealislically low values. EDC DNAPL. accumulated in the aquifer below the upper aquitard.
EDC DNALM, did not reach the regional (deepest) aquifer in any of the cases modeled. The limited extent of vertical EDC migration predicted is supported by ground water monitoring conducted over the four years since the spill.  相似文献   

11.
Volume reduction and lowering of capillary pressure within a large DNAPL pool are utilized as objectives in the design of a large-scale dual phase recovery system at a chemical manufacturing facility in the United States. By reducing DNAPL pool height through mass removal, capillary pressure is lowered, resulting in a reduced potential for future vertical and horizontal mobilization of the chlorinated solvent DNAPL pool. The DNAPL pool extends over an approximately 200 m by 275 m area in low permeability fill deposits overlying a clay aquitard. A three-dimensional multiphase flow model was employed to arrive at a final design incorporating nine horizontal drains (total length 664 m) and a pulsed pumping system. The numerical model was calibrated to the results of a 42-day field pilot-test involving the removal of approximately 25,000 L of DNAPL from a single, 55 m long horizontal drain. Numerical simulation revealed that gravity drainage, as opposed to hydraulic gradients in the water phase, is the dominant recovery mechanism at this site. This stems from the relatively high density and the viscosity of the DNAPL, and the relatively low permeability of the formation deposits. The use of pulsed pumping is shown to reduce the volume of contaminated ground water recovered from the 9-drain system, without significant reduction of the total volume of DNAPL recovered.  相似文献   

12.
At sites where a dense nonaqueous phase liquid (DNAPL) was spilled or released into the subsurface, estimates of the mass of DNAPL contained in the subsurface from core or monitoring well data, either in the nonaqueous or aqueous phase, can be highly uncertain because of the erratic distribution of the DNAPL due to geologic heterogeneity. In this paper, a multiphase compositional model is applied to simulate, in detail, the DNAPL saturations and aqueous-phase plume migration in a highly characterized, heterogeneous glaciofluvial aquifer, the permeability and porosity data of which were collected by researchers at the University of Tübingen, Germany. The DNAPL saturation distribution and the aqueous-phase contaminant mole fractions are then reconstructed by sampling the data from the forward simulation results using two alternate approaches, each with different degrees of sampling conditioning. To reconstruct the DNAPL source zone architecture, the aqueous-phase plume configuration, and the contaminant mass in each phase, one method employs the novel transition probability/Markov chain approach (TP/MC), while the other involves a traditional variogram analysis of the sampled data followed by ordinary kriging. The TP/MC method is typically used for facies and/or hydraulic conductivity reconstruction, but here we explore the applicability of the TP/MC method for the reconstruction of DNAPL source zones and aqueous-phase plumes. The reconstructed geometry of the DNAPL source zone, the dissolved contaminant plume, and the estimated mass in each phase are compared using the two different geostatistical modeling approaches and for various degrees of data sampling from the results of the forward simulation. It is demonstrated that the TP/MC modeling technique is robust and accurate and is a preferable alternative compared to ordinary kriging for the reconstruction of DNAPL saturation patterns and dissolved-phase contaminant plumes.  相似文献   

13.
Dense nonaqueous phase liquids (DNAPLs) are immiscible fluids with a specific gravity greater than, water. When present, DNAPLs present a serious and long-term source of continued ground water and soil contamination (Pankow and Cherry 1996). Accurate characterization and delineation of DNAPL in the subsurface is critical for evaluating restoration potential and for remedy design at a site. However, obtaining accurate and definitive direct evidence of DNAPL is difficult. A field study was recently performed comparing several approaches to DNAPL characterization at a site where anecdotal and limited direct evidence of DNAPL exists. The techniques evaluated included a three-dimensional high-resolution seismic survey, field screening of soil cores with a flame ionization detector (FID)/organic vapor analyzer (OVA), hydrophobic (Sudan IV) dye-impregnated reactive FLUTe® (Flexible Liner Underground Technologies) liner material in combination with Rotasonic drill cores, centrifuged soil with Sudan IV dye, ultraviolet light (UV) fluorescence, a Geoprobe® Membrane Interface Probe (MIP®), and phase equilibrium partitioning evaluations based on laboratory analysis of soil samples. Sonic drilling provided reliable continuous cores from which minor soil structures could be evaluated and screened with an OVA, The screening provided reliable preliminary data for identifying likely DNAPL zones and for selecting samples for further analyses. The FLUTe liner material provided the primary direct evidence of the presence of DNAPL and reliable information on the thickness and nature of its occurrence (i.e., pooled or ganglia). The MIP system provided good information regarding the subsurface lithology and rapid identification and delineation of probable DNAPL areas. The three-dimensional seismic survey was of minimal benefit to this study, and the centrifuging of samples with Sudan IV dye and the use of UV fluorescence provided no benefit. Results of phase equilibrium partitioning concentration calculations for soil samples (to infer the presence of DNAPL) were in good agreement with the site screening data. Additionally, screening data compared well with previous ground water data and supported using 1% of the pure phase solubility limit of Freon 113 (2 mg/L) as an initial means to define the DNAPL study area. Based on the results of this study, the preferred approach for identifying and delineating DNAPL in the subsurface is to initially evaluate ground water data and define an area where dissolved concentrations of the target analyte(s) approach 1% of the pure phase solubility limit. Within this study area, the MIP device is used to more specifically identify areas and lithologic zones where DNAPL may have accumulated. Core samples (either Rotasonic or Geoprobe) are then collected from zones where MIP readings are indicative of the presence of DNAPL. Soil samples from the free-product portions of the core(s) are then submitted to a laboratory for positive analyte identification. Soil analyses are then combined with site-specific geotechnical information (i.e., fraction organic carbon, soil bulk density, and porosity) and equilibrium partitioning algorithms used to estimate concentrations of organic contaminants in soil samples that would be indicative of free product. Used in combination, the soil analysis and the MIP records appear to provide accurate DNAPL identification and delineation.  相似文献   

14.
Dense nonaqueous phase liquid (DNAPL) source areas containing chlorinated volatile organic compounds (cVOCs) such as trichloroethene (TCE) and perchloroethene (PCE) often give rise to significant dissolved plumes in groundwater, leading to the closure of downgradient water supply wells and creating vapor intrusion issues in buildings located above the plume. Hydraulic containment via pump‐and‐treat has often been implemented to limit migration but must continue indefinitely. Removal of the DNAPL source area by means such as in situ thermal remediation (ISTR) offers the potential to diminish or end the need for hydraulic containment if the associated dissolved plume attenuates sufficiently following source removal. A question often raised is whether this occurs or whether the back diffusion of contaminants from secondary sources such as low‐permeability lenses in the dissolved plume precludes it. The authors conducted DNAPL source removal using ISTR at dozens of sites. This paper presents a compilation of cases—10 separate DNAPL source areas at five project sites—where data indicate that the implementation of a thorough ISTR in a DNAPL source area can result in the attenuation of the associated dissolved plume, such that in several cases, long‐standing pump‐and‐treat systems could be turned off. Our findings contrast with recent assertions that aggressive source remediation may not be justifiable because dissolved plume concentrations will not decline sufficiently. We show that the application of ISTR can result in the thorough removal of the DNAPL source, effective diminution of dissolved plume groundwater concentrations, and achievement of drinking water standards.  相似文献   

15.
Large-scale column experiments were undertaken to evaluate the potential of polymer mats to remove selected volatile organic compounds, polycyclic aromatic hydrocarbons, and pesticides (atrazine and fenamiphos) from ground water and potentially to act as permeable reactive barriers in contaminated ground water environments. The polymer mats, composed of interwoven silicone (dimethylsiloxane) tubes and purged with air, were installed in 2 m long flow-through columns. The polymer mats proved efficient in physically removing (stripping) benzene and naphthalene from contaminated water. Removal efficiencies for both these compounds from an aqueous phase flowing past a polymer mat were 75% or greater. However, for atrazine and fenamiphos, removal efficiencies were 5% or less, probably as a result of their lower Henry's law constants and possibly lower polymer diffusion coefficients.
These experiments indicate that, at least for relatively volatile compounds, polymer mats can provide a remediation technique for the removal of organic compounds from contaminated water. Application of this technique may be well suited as a longer-term, semipassive strategy to remediate contaminated ground water, using natural ground water flow to deliver contaminated ground water to polymer mats engineered as sorption-stripping barriers.
Additional benefits of this technique may include targeted delivery of gaseous chemical amendments, such as oxygen, to enhance aerobic biodegradation and to further reduce any residual concentrations of contaminants.  相似文献   

16.
Optimal cost pump-and-treat ground water remediation designs for containment of a contaminated aquifer are often developed using deterministic ground water models to predict ground water flow. Uncertainty in hydraulic conductivity fields used in these models results in remediation designs that are unreliable. The degree to which uncertainty contributes to the reliability of remediation designs as measured by the characterization of the uncertainty is shown to differ depending upon the geologic environments of the models. This conclusion is drawn from the optimal design costs for multiple deterministic models generated to represent the uncertainty of four distinct models with different geologic environments. A multi scenario approach that includes uncertainty into the remediation design called the deterministic method for optimization subject to uncertainty (DMOU) is applied to these distinct models. It is found that the DMOU is a method for determining a remediation design subject to uncertainty that requires minimal postprocessing efforts. Preprocessing, however, is required for the application of the DMOU to unique problems. In the ground water remediation design problems, the orientation of geologic facies with respect to the orientation of flow patterns, pumping well locations, and constraint locations are shown to affect the preprocessing, the solutions to the DMOU problems, and the computational efficiency of the DMOU approach. The results of the DMOU are compared to the results of a statistical analysis of the effects of the uncertainty on remediation designs. This comparison validates the efficacy of the DMOU and illustrates the computational advantages to using the DMOU over statistical measures.  相似文献   

17.
The influence of model dimensionality on predictions of mass recovery from dense non-aqueous phase liquid (DNAPL) source zones in nonuniform permeability fields was investigated using a modified version of the modular three-dimensional transport simulator (MT3DMS). Thirty-two initial two- (2D) and three-dimensional (3D) tetrachloroethene–DNAPL source zone architectures, taken from a recent modeling study, were used as initial conditions for this analysis. Commonly employed source zone metrics were analyzed to determine differences between 2D and 3D predictions: (i) down-gradient flux-averaged contaminant concentration, (ii) reductions in contaminant mass flux through a down-gradient boundary, (iii) source zone ganglia-to-pool (GTP) ratio, and (iv) time required to achieve a remediation objective. 3D flux-averaged contaminant concentrations were approximately 3.5 times lower than concentrations simulated in 2D. This difference was attributed to dilution of the contaminant concentrations down gradient of the source zone. Contaminant flux reduction predictions for a given mass recovery were generally 5% higher in 3D simulations than in 2D simulations. The GTP ratio declined over time as mass was recovered in both 2D and 3D simulations. Although the source longevity (i.e., time required to achieve 99.99% mass recovery) differed between individual 2D and 3D realizations, the mean source longevity for the 2D and 3D simulation ensembles was within 2%. 2D simulations tended to over-predict the time required to achieve lower mass recovery levels (e.g. 50% mass recovery) due to a smaller contaminated area exposed to uncontaminated water. These findings suggest that ensemble averages of 2D numerical simulations of DNAPL migration, entrapment, dissolution, and mass recovery in statistically homogenous, nonuniform media may provide reasonable approximations to average behavior obtained using simulations conducted in fully three-dimensional domains.  相似文献   

18.
DNAPL to LNAPL Transitions During Horizontal Cosolvent Flooding   总被引：1，自引：0，他引：1  
Cosolvent flooding is a technology with the potential to remove nonaqueous phase liquid (NAPL) sources from the subsurface. It can be used to initiate separate phase mobilization, which allows removal of NAPL within very few pore volumes. Mobilization may result in a sinking DNAPL bank during horizontal flooding of NAPLs denser than water. Reversal of phase density difference between aqueous and DNAPL phases could potentially avoid this downward migration of mobilized DNAPLs. We achieved phase density difference reversal and made DNAPLs float using two components in the cosolvent flooding solution. A low-density cosolvent partitions preferentially into the DNAPL and swells it, which causes a reduction in density of the DNAPL and reversal of the density difference between the NAPL and aqueous phases. A highdensity additive that remains in the aqueous phase allows the cosolvent flooding solution overall to have a density greater than that of water and permits control of the flooding instability. This study focused on tert-butanol as the swelling cosolvent and tetrachloroethylene as the contaminant. In batch tests with sucrose and glycerol as dense additives, phase density difference reversal occurred. To investigate the applicability of phase density difference reversal as a remediation technology, horizontal column and sandbox experiments were performed. These experiments demonstrated the occurrence of phase density difference reversal and effective remediation in horizontal cosolvent floods.  相似文献   

19.
A three-dimensional two-phase flow model is coupled to a non-linear reactive transport model to study the efficacy of potassium permanganate treatment on dense, non-aqueous phase liquid (DNAPL) source removal in porous media. A linear relationship between the soil permeability (k) and concentration of manganese dioxide precipitate ([MnO2(s)]), k = ko + Srind [MnO2(s)], is utilized to simulate nodal permeability reductions due to precipitate formation. Using published experimental column studies, an Srind = −5.5 × 10−16 m2 L/mg was determined for trichloroethylene (TCE) DNAPL. This Srind was then applied to treatment simulations on three-dimensional TCE DNAPL source zones comprising either DNAPL at residual saturations, or DNAPL at pooled saturations.  相似文献   

20.
Hydraulic displacement is a mass removal technology suitable for stabilization of a dense, nonaqueous phase liquid (DNAPL) source zone, where stabilization is defined as reducing DNAPL saturations and reducing the risk of future pool mobilization. High resolution three-dimensional multiphase flow simulations incorporating a spatially correlated, heterogeneous porous medium illustrate that hydraulic displacement results in an increase in the amount of residual DNAPL present, which in turn results in increased solute concentrations in groundwater, an increase in the rate of DNAPL dissolution, and an increase in the solute mass flux. A higher percentage of DNAPL recovery is associated with higher initial DNAPL release volumes, lower density DNAPLs, more heterogeneous porous media, and increased drawdown of groundwater at extraction wells. The fact that higher rates of recovery are associated with more heterogeneous porous media stems from the fact that larger contrasts in permeability provide for a higher proportion of capillary barriers upon which DNAPL pooling and lateral migration can occur. Across all scenarios evaluated in this study, the ganglia-to-pool (GTP) ratio generally increased from approximately 0.1 to between approximately 0.3 and 0.7 depending on the type of DNAPL, the degree of heterogeneity, and the imposed hydraulic gradient. The volume of DNAPL recovered as a result of implementing hydraulic displacement ranged from between 9.4% and 45.2% of the initial release volume, with the largest percentage recovery associated with 1,1,1 trichloroethane, the least dense of the three DNAPLs considered.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号